We always knew backward compatibility with the ES3 bootrom, which was
finalised about a year ago, would be a pain. Here we go again.
The bootrom does not support control requests added after it was burnt
into ROM for obvious reasons. This means that we need to suppress
sending the new bundle_activate() operation to any interface executing
the legacy bootrom.
Do so by adding a new NO_PM interface quirk (we can use the
control-protocol version for this later once we bump it).
Note that the interface-disable path (e.g. for power down) is already
handled by the FORCED_DISABLE quirk, and that the suspend/resume
paths are currently avoided by making sure that the bootrom bundle
never suspends.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Make sure to prevent an interface that is going away from being
reactivated.
This is needed to preemptively close a race between the upcoming feature
to reactivate a powered-down interface and physical removal (i.e.
module_removed event processing) as well as logical removal (e.g. the
current system-suspend hack).
Reviewed-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Patrick Titiano <ptitiano@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
It will soon be possible to reactivate an interface that has been
powered down after already having been activated. In that case there's
no need to re-read the DME attributes as part of activation as the
values are already cached.
Reviewed-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Patrick Titiano <ptitiano@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Use an enum for the interface type instead of using the SVC protocol
values directly.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sandeep Patil <sspatil@google.com>
Reviewed-by: Patrick Titiano <ptitiano@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add an interface-type string attribute that represents the detected
interface type as either "dummy", "unipro", "greybus", or "unknown".
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sandeep Patil <sspatil@google.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This patch adds the core timesync functionality.
0. arche-platform.c/arche-apb-ctrl.c
Modifies the platform layer to hook the incoming TIME_SYNC signal up to
the timesync strobe IRQ handler. If the arche-platform driver can't
satisfy the request for the wake-detect line, it will return -EAGAIN and
the calling work-queue must reschedule the attempt to get exclusive
access to the wake-detect pin logic. A private data field is added to
the arche-platform driver to enable passing of a timesync pointer to the
ISR responsible for synchronizing time.
1. timesync.c
A new file added which contains all of the logic associated with sending
greybus commands to SVC, APBx or Interfaces to enable, disable and
disseminate timing information.
2. timesync_platform.c
Any platform/arch specific code goes into timesync_platform.c.
Originally the idea was to keep the x86 and ARM arch dependencies in a
timesync_platform_arch.c file - however with further refinement that's
currently not necessary however just-in-case it becomes necessary to
resuscitate arch or platform specific methods for accessing timer
resources that access shouldn't be part of the core timesync.c logic and
so for the moment we access these timer resources through a thin access
layer in timesync_platform.c. Expect this to go away long term ideally.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add a generic interface for bundle drivers to use to request that a
mode switch is carried out on its behalf.
Mode switching involves tearing down all connections to an interface,
sending a unidirectional mode-switch request, and waiting for a mailbox
event that triggers deferred control connection reset and re-enumeration
of the interface. In case of a timeout waiting for the interface mailbox
event, or on other errors, the interface is powered off.
All of this needs to be done by core from work-queue context in order
not to block incoming SVC requests and bundle-device tear down. Care
must also be taken to serialise against concurrent module removal events
and eject requests.
Special handling of legacy mode-switching is also added in order to
continue to support the ES3 bootrom.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add an interface quirk flag to suppress I/O during interface disable.
This is needed to prevent I/O to the bootrom during controlled
connection tear down (e.g. eject or driver unbind). This will be more
obvious with the new connection tear-down procedure.
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The Interface description in the Greybus specification contains a
'features' field which is currently not implemented on the AP side. The
Interface features field provides information on optional attributes of an
Interface as a bitmask. Currently only GREYBUS_INTERFACE_FEATURE_TIMESYNC
is implemented in the specification but, the expectation is that other
feature flags will be added over time.
This patch adds support to extract the feature byte communicated in the
features field of the Interface Descriptor header and extends struct
interface to contain a features field through which any user with a pointer
to struct interface may interrogate the features of an Interface.
This is a necessary pre-cursor for TimeSync to ensure only Interfaces which
declare GREYBUS_INTERFACE_FEATURE_TIMESYNC will be included when we go
through the process of FrameTime synchronization.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The interface-version request was just removed so remove the now unused
interface-version quirk.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This reverts commit b957ade7b3e4ab8c149c53346dbf02e977b7f3a7.
The interface version is now managed as part of the firmware-management
protocol. This operation is already removed from the greybus
specifications.
Drop interface version support from greybus.
Tested with gbsim (sysfs file not available after this patch).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Acked-by: Sandeep Patil <sspatil@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove unused function prototype that was left after a recent change.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add active state flag to avoid deactivating an interface which is
already off.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Implement controlled module removal through a new module attribute
"eject".
When a non-zero argument is written to the attribute, all interfaces of
the module are disabled (e.g. bundles are deregistered) and deactivated
(e.g. powered off) before instructing the SVC to physically eject the
module.
Note that the module device is not deregistered until the SVC has
reported the physical removal of all of its interfaces.
A new interface mutex is added to enforce interface state-change
serialisation.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add Greybus module abstraction that will be used to implement controlled
module removal (eject) and represent module geometry.
Greybus module devices correspond to physical modules and have one or
more interfaces. Modules have an id that is identical to the id of their
primary interface, which in turn is the interface with lowest numbered
id. The module name is constructed from the bus and module id:
<bus_id>-<module_id>
Interfaces, bundles, and control devices are consequently renamed as
<bus_id>-<module_id>.<interface_id>
<bus_id>-<module_id>.<interface_id>.<bundle_id>
<bus_id>-<module_id>.<interface_id>.ctrl
As before, interface ids (and therefore in a sense now also module ids)
correspond to physical interface positions on the frame.
Modules have the following attributes:
module_id
num_interfaces
where module_id is the id of the module and num_interface the number of
interfaces the module has.
Note that until SVC module-size detection has been implemented, all
interfaces are considered to be part of 1x2 modules. Specifically, the
two interfaces of a 2x2 module will be presented as two 1x2 modules for
now.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Make the control-device lifetime coincide with when the interface is
enabled (enumerated).
This is needed to be able register a new control device after a mode
switch.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The control device is an abstraction of the control connection over
which a greybus manifest is retrieved. As interfaces switch modes (e.g.
after boot-over-unipro) they expose new manifests, which can contain
different vendor and product strings.
Eventually control devices will be deregistered and recreated after an
interface mode switch, while the interface itself remains registered.
Note that only interfaces of type greybus will have control devices.
Specifically, dummy interfaces will not.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Clean up the ES2 VID/PID hack using a new quirk flag.
Note that the hack is now used if and only if the interface is a Toshiba
ES2 bridge (and not if the attributes read zero).
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Read the DDBL1 and Ara DME attributes when activating an interface.
These values are currently provided by the SVC in the intf_hotplug
request, which is about to go away.
Note that there are currently no standard Ara VID and PID attributes and
that Toshiba uses attributes from the reserved space in ES3. For now, we
therefore refuse to enumerate any non-Toshiba bridges.
Also note that the Ara serial number is currently not supported.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Clean up the device id-handling and make sure we never allocate invalid
device ids due to a missing upper bound.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Creating and destroying a route to an interface is arguably an interface
operation and belongs with the interface code.
Add new interface_activate and interface_deactivate helpers that will be
used to activate and deactivate an interface in the new interface boot
sequence.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Clean up handling of the ES3-bootrom quirks by adding an interface
quirk-flags field that is set appropriately when we detect that the ES3
bootrom is running.
Note that we need to reserve the DME_DIS_UNIPRO_BOOT_STARTED and
DME_DIS_FALLBACK_UNIPRO_BOOT_STARTED status values for the ES3 bootrom,
which does not support any CPort features (unlike later boot stages).
Add a BOOTROM infix to the defines to make this more clear.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Separate interface disable from interface removal.
Disabling an interface means tearing down its control connection and
destroying (i.e. deregistering and releasing) its bundles, while
removing it means deregistering and releasing the interface itself.
This is needed to implement controlled module removal, where the module
interfaces are disabled before being physically ejected.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Rename the interface-initialisation function gb_interface_enable(),
which is more descriptive.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Move helper to remove all interfaces of a host-device to the svc code
and call it when removing the svc device as this needs to be coordinated
with flushing the SVC work queue.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Separate interface initialisation from registration of the interface and
its bundles.
This is a step towards registering also interfaces that failed to
initialise (e.g. a dummy interface).
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add interface-route-create helper to allocate an interface device id and
setup the route.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove the unused interface drvdata helpers along with some dubious
comments about public and private definitions.
Greybus drivers bind to bundles and should be using the
greybus_set_drvdata and greybus_get_drvdata helpers.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Reviewed-by: Jeffrey Carlyle <jcarlyle@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The version of the currently running firmware on the module is useful
for userspace as it can be used to find if an update is available or
not. This patch fetches interface's version with a new control operation
and exposes the same in userspace.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Two exactly same modules can be uniquely identified using module's
serial-number. This patch updates the interface hotplug event to also
receive the serial-number of the module.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The Device descriptor block Level 1 (DDBL1) attributes are specified by
the MIPI standard and prefixing them with 'unipro_' isn't the best thing
to do. They should be prefixed with DDBL1 instead.
To make it more readable/clear:
- rename macros and variable by prefixing them with ddbl1_.
- write full names for mfg and prod ids as manufacturer and product ids.
- replace mfg (manufacturing) with mfr (manufacturer)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Set an interface disconnected flag when the interface has been
hot-unplugged (e.g. forcibly removed or after a reboot), and use it to
disable the control connection early when deregistering the interface
and its bundles.
This avoids a one-second (default) timeout for every enabled connection
(e.g. one per bundle) at hot-unplug, something which for the default
gpbridge manifest currently amounts to five seconds.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Kill gb_create_bundle_connection, which was only used to create the
control bundle and connection, and replace it with a specialised static
helper.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Make interfaces child devices of host devices.
The new interface device name is "<bus_id>-<intf_id>", where bus_id is
the dynamically allocated bus id for the host device and intf_id is the
svc-allocated interface id.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix vendor and product matching by matching on the 32-bit Ara vendor and
product ids.
Remove the "fake" 16-bit vendor and product ids and export the Ara ids
using the "vendor" and "product" interface attributes instead.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove the unimplemented interface unique-id.
There will eventually be an interface-serial-number attribute provided,
but let's not export it or commit to a name for this attribute until we
need it.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We need to skip setting E2EFC and other flags to the SVC connection
create request, for all cports, on an interface that need to boot over
unipro, i.e. interfaces required to download firmware.
This also adds a FIXME as we need to do it differently for ES3.
Tested-by: Eli Sennesh <esennesh@leaflabs.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off by: Eli Sennesh <esennesh@leaflabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The callers already have a valid interface pointer and there is no need
for gb_interface_remove() to find the interface again.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This shall be used later to find a firmware blob for the interface, lets
save it in the interface structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add a public declaration for gb_interface_destroy(), matching
gb_interface_create().
It's not yet used outside "interface.c" but I suppose it
could be, and its scope is currently public.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Its not referenced by svc or any other code anymore, lets stop exposing
it to rest of the files.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Perry Hung <perry@leaflabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Its not updated/used anymore, remove it. Also move back the struct
gb_svc to svc.c as its not referenced by external users anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Perry Hung <perry@leaflabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
SVC connection is required before the AP knows its position on the endo
and type of endo. To enable message processing between the AP and SVC at
this time, we need a partially initialized connection which can handle
these messages.
Once the AP receives more information from the SVC, it can discard this
partially initialized connection and create a proper one, tied to a
bundle and interface.
Destroying the partially initialized connection is a bit tricky, as it
is required to send a response to svc-hello. That part will be properly
fixed separately.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We need to create bundle/connection for svc cport after the endo layout
and interface id is known to the AP. gb_create_control_connection() can
be reused for this, but it should be renamed to something more
appropriate, as its not about control-connection anymore.
Lets name it gb_create_bundle_connection().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Its another special protocol (just like control protocol) and is
required to be accessed from other files, lets save a pointer to it in
interface structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
While introducing bundles, the device_id also got moved to the bundle,
whereas it identifies an interface block to the AP.
Move it back to interface instead of bundle.
Calls to gb_bundle(s)_init() are dropped as connections will be
initialized while they are created now, as device_id will be valid.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>