This cleans up the kilauea/halekala board ports to use the ppc40x_simple
platform support.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This cleans up the makalu board port to use the ppc40x_simple platform
support.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Now that the 4xx NAND driver is available again in arch/powerpc, let's
enable it on Sequoia. This patch also disables the early debug messages
(CONFIG_PPC_EARLY_DEBUG) in the Sequoia defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The single board defconfig files were missed during the cleanup
of CONFIG_PCI_LEGACY in the multi-board config files. This
disables the option for the single board configs, as it isn't
used by anything for these boards.
Reported-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Refresh and set these options:
CONFIG_SYSFS_DEPRECATED_V2: y -> n
CONFIG_INPUT_JOYSTICK: y -> n
CONFIG_HID_SONY: n -> m
CONFIG_RTC_DRV_PS3: - -> m
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the vast majority of 85xx platforms are UP we introduce a new SMP
config for the few platforms that have more than one core. Beyond
CONFIG_SMP=y and its dependencies this should be identical to
mpc85xx_defconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable highmem support for the TQM8548-AG modules and NAND support for
the TQM8548-BE modules. Furthermore disable USB, Wireless and IDE support
because it's not available on the STK85xx starter kit.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.
The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.
For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:
can@3,100 {
compatible = "philips,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 2>;
interrupts = <2 8 1>; // number, type, routing
interrupt-parent = <&fpga_pic>;
};
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Most of the code enabled by these options is __init, and it's much
more useful to actually run the tests.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Support for the PPC9A VME Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the default config file for GE Fanuc's PPC9A, a 6U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Defining flash partition table in platform code is deprecated, and due to
recent changes linkstation and storcenter do not compile any more with
their default configurations because of undefined references to
physmap_set_partitions(). Instead of fixing them by using the correct
kernel configuration macro in preprocessor conditional, remove partition
table definitions altogether. Instead add support for partition definition
on the command-line and in device tree to the default configurations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Virtex FPGA designs have two serial port logic cores to choose from; the
simple uartlite, and the full featured uart16550. Both cores are in
common use so the defconfig should support both of them. Currently
only console on uartlite is supported in the defconfig. This patch adds
console support for the 16550 core.
The Virtex reference designs do not work without this patch.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The following options are enabled to support the digsy-mtc.
- LXT phy
- AT24 eeprom
- RTC (DS1337)
- MTD partitioning based on OF description
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the device-tree entries for a handful of devices on the
Canyonlands board, such as the EHCI and OHCI controllers, the real
time clock and the AD7414 thermal monitor.
I also updated the defconfig to enable various options related to
these devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
CONFIG_CC_OPTIMIZE_FOR_SIZE is selected, because otherwise the kernel
wouldn't boot. The AmigaOne's U-boot firmware seems to have a problem
loading uImages bigger than 1.8 MB.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
TSEC0 is connected to Vitesse 7385 5-port switch. The switch
isn't connected to any mdio bus, the link to the switch is fixed
to Full-duplex 1000 Mb/s (no pause).
This patch fixes following failure during bootup:
mdio@24520:01 not found
eth0: Could not attach to PHY
IP-Config: Failed to open eth0
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds basic support for the 6 GPIO lines found on GE Fanucs SBC310 to the GE Fanuc GPIO driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the default config file for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
