We were scanning for 0xFF through the entire chip -- which takes a while
when it's a 512MiB device as I have on my current toy. The specs only say
we need to check certain bytes -- so do only that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Implement HW ECC support,
- Provide read_buf() and write_buf() routines using memcpy
- Use on-flash bad block table
- Fix module refcounting
- Avoid read/modify/write in hwcontrol()
- Minor cosmetic fixes
Partly based on code and ideas from Tom Sylla <tom.sylla@amd.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
One Block of the NAND Flash Array memory is reserved as
a One-Time Programmable Block memory area.
Also, 1st Block of NAND Flash Array can be used as OTP.
The OTP block can be read, programmed and locked using the same
operations as any other NAND Flash Array memory block.
OTP block cannot be erased.
OTP block is fully-guaranteed to be a valid block.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
There's some problem with write oob in serveral platform.
So we write oob with oobsize aligned (16bytes) instead of 3 bytes (from {2,
3})
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Some free byte positions at onenand_oob_64 were wrong. This was also
reported by Christian Lehne. 3 byte slots are at 2+16*i and 2 byte
slots at 14+16*i.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for MTD_PCMCIA_ANONYMOUS.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Oops. Stupid StudlyCaps. Again.
This driver is doubly-deprecated because is was subsumed into doc2000.c
and _also_ we want people to start using the new NAND wrapper for these
devices anyway. But ISTR there was still one person using it because
something didn't work for them. Must chase that up and then I can kill
this.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This lacks hardware ECC support and a few optimisations we're going to
want fairly soon, but it works well enough to mount and use JFFS2.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
After dwmw2 let me know it ought to be done, I rewrote the physmap map
driver to be a platform driver. I know zilch about the driver model,
so I probably botched it in some way, but I've done some tests on an
ixp23xx board which uses physmap, and it all seems to work.
In order to not break existing physmap users, I've added some compat
code that will instantiate a platform device iff CONFIG_MTD_PHYSMAP_LEN
is defined and != 0. Also, I've changed the default value for
CONFIG_MTD_PHYSMAP_LEN to zero, so that people who inadvertently
compile in physmap (or new, platform-style, users of physmap) don't get
burned.
This works pretty well -- the new physmap driver is a drop-in replacement
for the old one, and works on said ixp23xx board without any code changes
needed. (This should hold as long as users don't touch 'physmap_map'
directly.)
Once all physmap users have been converted to instantiate their own
platform devices, the compat code can go. (Or we decide that we can
change all the in-tree users at the same time, and never merge the
compat code.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The TS-72xx is a series of embedded single board computers from
Technologic Systems based on the Cirrus ep93xx (arm920t based) CPU.
The TS-7200 uses NOR flash, while all the other models in the series
(TS-7250, TS-7260) use NAND flash -- included is a driver for the NAND
flash on those boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Toralf Förster found a compile error when CONFIG_MTD_SC520CDP=y and
CONFIG_MTD_CONCAT=n:
drivers/built-in.o: In function `init_sc520cdp':
sc520cdp.c:(.init.text+0xb4de): undefined reference to `mtd_concat_create'
drivers/built-in.o: In function `cleanup_sc520cdp':
sc520cdp.c:(.exit.text+0x14bc): undefined reference to `mtd_concat_destroy'
This patch fixes it.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Expand the parameter parsing for block2mtd. It now accepts:
Ki, Mi, Gi - the official prefixes for binary multiples,
see http://physics.nist.gov/cuu/Units/binary.html,
ki - mistake on my side and analog to "k" for decimal multiples,
KiB, MiB, GiB - for people that prefer to add a "B" for byte,
kiB - combination of the above.
There were complaints about not accepting "k" for 1024. This has long
been common practice, but is known to lead to confusion. Hence the new
SI units and hence block2mtd only accepts units that cannot be confused
with decimal units. Diverging from common practice doesn't always please
people, even if the change is for the better.
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch removes repeated calls to kmalloc / kfree in mtd_write /
mtd_read functions, replacing them by a single kmalloc / kfree pair.
Signed-off-by: Thiago Galesi <thiagogalesi@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Several flags are set by some devices, but never checked. Remove them.
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
mtdblock_ro is by definition readonly. Remove the silly checks.
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
mtdblock is the only user of aggregate capabilities in mtd. This is clearly
bogus and should be changed. In particular, it tries to determine whether
the device in question is a piece of RAM. For every single driver that fits
the current criteria, an easier test would be to check for the type being
MTD_RAM.
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix printk format warning:
drivers/mtd/devices/m25p80.c:189: warning: format '%zd' expects type
'signed size_t', but argument 6 has type 'u_int32_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I just hit the following error and warning :
drivers/mtd/maps/nettel.c: In function `nettel_init':
drivers/mtd/maps/nettel.c:418: error: `ROOT_DEV' undeclared (first use in this function)
drivers/mtd/maps/nettel.c:418: error: (Each undeclared identifier is reported only once
drivers/mtd/maps/nettel.c:418: error: for each function it appears in.)
drivers/mtd/maps/nettel.c:418: warning: implicit declaration of function `MKDEV'
make[3]: *** [drivers/mtd/maps/nettel.o] Error 1
make[2]: *** [drivers/mtd/maps] Error 2
make[1]: *** [drivers/mtd] Error 2
The patch fixes the missing ROOT_DEV declaration by including linux/root_dev.h
and fixes the implicit declaration of MKDEV by including linux/kdev_t.h .
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove the blkmtd driver.
- An alternative exists (block2mtd) that hasn't had bug report for > 1 year.
- Most embedded people tend to use ancient kernels with custom patches from
mtd cvs and elsewhere, so the 1 year warning period neither helps nor hurts
them too much.
- It's in the way of klibc. The problems caused by pulling blkmtd support
are fairly low, while the problems caused by delaying klibc can be fairly
substantial. At best, this would be a severe burden on hpa's time.
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
Remove the obsolete Kconfig options MTD_CFI_AMDSTD_RETRY
and MTD_CFI_AMDSTD_RETRY_MAX
The code that depended on these was removed in early 2004, but
Kconfig was not updated accordingly.
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix an obvious off-by-one error (vmax_mtd[] contains two elements).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/mtd/devices/blkmtd.c uses a local declaration of name_to_dev_t()
which is inconsistant with the real one. the following patch fixes this by
removing the local declaration and including mount.h instead
this patch was originally done by Micah Anderson.
Signed-off-by: Herbert Poetzl <herbert@13thfloor.at>
Acked-by: Micah Anderson <micah@riseup.net>
Acked-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Redboot simply sets the first character of a fis entry to 0xff on "fis
delete". The kernel redboot parser stops parsing on such an entry, and
without this patch any entries after a deleted image would not be detected.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds flash chip used in Sharp Zaurus sl5500 (collie) to jedec_probe.
Values work for read-only access, but I have not figured out how to do
read-write.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes coverity bug #12. The first two gotos in the function still
have the initial value for mtd set. And the third goto just triggers for
!mtd
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill unneccessary ifdefs in mtdcore.c.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a copy/paste bug found by cpminer inside the inftlcore.c file
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current cmdlinepart.c uses offset value 0 to specify a continuous
partition. This prevents creating a second partition starting at 0.
For example, I can split 4MB device using "mtdparts=id:2M,2M", but I can
not do "mtdparts=id:2M@2M,2M@0" to swap mtd0 and mtd1.
This patch introduces special OFFSET_CONTINUOUS value for a continuous
partition and allows 0 for offset value.
Also this patch replaces 0xffffffff with UINT_MAX for SIZE_REMAINING.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MTD_NAND=m and MTD_NAND_SHARPSL=y or MTD_NAND_NANDSIM=y are illegal
combinations that mustn't be allowed.
This patch fixes this bug by making MTD_NAND_SHARPSL and MTD_NAND_NANDSIM
tristate's.
Additionally, it fixes some whitespace damage at these options.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Acked-by: "Artem B. Bityutskiy" <dedekind@yandex.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- chips/sharp.c: make two needlessly global functions static
- move some declarations to a header file where they belong to
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/mtd/devices/m25p80.c: In function `m25p80_erase':
drivers/mtd/devices/m25p80.c:189: warning: signed size_t format, different type arg (arg 6)
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Handle the _modifying_ operation sm91c92_cs requires in
pcmcia_modify_configuration, so that the only remaining users
of pcmcia_release_configuration() are within the pcmcia core
module.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in the block-erase optimization for Dataflash; it was using block
erase even for smaller segments that need page erase.
That wouldn't matter for JFFS2, which never erases less than one block
(sometimes several blocks), but for other callers it might.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sync up the recent redboot fix with MTD CVS. It uses the correct swab()
functions.
Cc: John Bowler <jbowler@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The RedBoot boot loader writes flash partition tables containing native
byte sex 32 bit values. When booting an opposite byte sex kernel (e.g. an
LE kernel from BE RedBoot) the current MTD driver fails to handle the
partition table and therefore is unable to generate the correct partition
map for the flash.
So far as I am aware this problem is ARM specific, because only ARM
supports software change of the CPU (memory system) byte sex, however the
partition table parsing is in generic MTD code. The patch below has been
tested on NSLU2 (an IXP4XX based system) with a patch,
10-ixp4xx-copy-from.patch (submitted to linux-arm-kernel - it's ARM
specific) required to make the maps/ixp4xx.c driver work with an LE kernel.
Builds of the patched system are in the 'unstable' release of OpenSlug and
UcSlugC available from www.nslu2-linux.org. These builds are BE, the
archives at www.nslu2-linux.org and www.handhelds.org (see
monotone.vanille.de) can be built LE (currently DISTRO targets
nslu-ltu.conf for LE thumb uclibc (32 bit kernel) and nslu2-lau.conf,
nslu2-lag.conf for LE arm uclibc/glibc) and this patch has been tested
extensively will both BE and LE systems on the NSLU2 (including swapping
between BE and LE by reflashing from both RedBoot and Linux).
The patch recognises that the FIS directory (the partition table) is
byte-reversed by examining the partition table size, which is known to be
one erase block (this is an assumption made elsewhere in redboot.c). If
the size matches the erase block after byte swapping the value then
byte-reversal is assumed, if not no further action is taken. The patched
code is fail safe; should redboot.c be changed to support a partition table
with a modified size field the test will fail and the partition table will
be assumed to have the host byte sex.
If byte-reversal is detected the patch byte swaps the remainder of the 32
bit fields in the copy of the table; this copy is then used to set up the
MTD partition map.
Signed-off-by: John Bowler <jbowler@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a kernel oops for Intel P30 flashes, where the wait queue head was not
initialized for the flchip struct, which in turn caused a crash at the
first read operation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found an issue in cfi_cmdset0001.c. It is related to cache region
invalidation in the buffered write procedure.
The code performs cache invalidation from "cmd_addr" to "cmd_adr + len" in
do_write_buffer() while we modify region from "adr" to "adr+len".
This issue affects writes + reads of data by small chunks.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MTD_XIP depends on having working asm/mtd-xip.h; it's not just per-architecture
(arm-only, as current Kconfig would have it), but actually per-subarch as
well. Introduced a new symbol (ARCH_MTD_XIP) set by arch Kconfig; MTD_XIP
depends on it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
CC drivers/mtd/maps/dc21285.o
drivers/mtd/maps/dc21285.c: In function `dc21285_copy_to_32':
drivers/mtd/maps/dc21285.c:113: error: invalid lvalue in increment
drivers/mtd/maps/dc21285.c: In function `dc21285_copy_to_16':
drivers/mtd/maps/dc21285.c:124: error: invalid lvalue in increment
drivers/mtd/maps/dc21285.c: In function `dc21285_copy_to_8':
drivers/mtd/maps/dc21285.c:134: error: invalid lvalue in increment
make[3]: *** [drivers/mtd/maps/dc21285.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Build kernel/intermodule.c only when required.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the wrong dependency of MTD_OBSOLETE_CHIPS on BROKEN and
marks the non-compiling MTD_AMDSTD and MTD_JEDEC drivers as BROKEN.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This collects some small SPI patches that seem to be missing from the MM tree:
- spi_butterfly kbuild hooks got dropped somehow; this restores them
- quick fix for a (theoretical?) m25p80_write() oops noted by Andrew
- quick fix for a potential config-specific oops for mtd_dataflash()
- minor doc tweaks
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.
From: David Brownell <dbrownell@users.sourceforge.net>
Updates including doc, bugfixes to the list code, add
spi_message_add_tail(). Plus, initialize things _before_ grabbing the
locks in some cases (in case it grows more expensive). This also merges
some bitbang updates of mine that didn't yet make it into the mm tree.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was originally a driver for the ST M25P80 SPI flash. It's been
updated slightly to handle other M25P series chips.
For many of these chips, the specific type could be probed, but for now
this just requires static setup with flash_platform_data that lists the
chip type (size, format) and any default partitioning to use.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mike Lavender <mike@steroidmicros.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a conversion of the AT91rm9200 DataFlash MTD driver to use the
lightweight SPI framework, and no longer be AT91-specific. It compiles
down to less than 3KBytes on ARM.
The driver allows board-specific init code to provide platform_data with
the relevant MTD partitioning information, and hotplugs.
This version has been lightly tested. Its parent at91_dataflash driver has
been pretty well banged on, although kernel.org JFFS2 dataflash support was
acting broken the last time I tried it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
at least 2.6.10
- interest seems to have dried up around March 2003.
Therefore, remove EPXA10DB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This (and the three subsequent patches) is working well on OMAP H4 with
2.6.15-rc4 kernel and passes the LTP fs test.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SetPageDirty() and ClearPageDirty() are low-level thing which filesystems
shouldn't be using. They bypass dirty page accounting.
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- every file should #include the headers containing the prototypes for
it's global functions
- make needlessly global functions static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Update the pre-CFI Sharp driver sharps.c so it compiles. map_read32 /
map_write32 no longer exist in the kernel so the driver is totally broken
as it stands. The replacement functions use different parameters resulting
in the other changes.
Change collie to use this driver until someone works out why the cfi driver
fails on that machine.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Tested-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The patch below fixes the following sparse warning:
drivers/mtd/maps/nettel.c:482:27: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arjan: drivers/mtd/maps/sc520cdp.c:167: warning: par_table is never written to and should be declared 'const'
arjan: drivers/mtd/maps/pci.c:105: warning: mtd_pci_map is never written to and should be declared 'const'
arjan: mind fixing those up ?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ixp4xx updates:
- Handle reads that don't start on a half-word boundary.
- Make it work when CPU is in little-endian mode.
Signed-off-by: John Bowler <jbowler@acm.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
