Add #define pr_fmt(fmt) KBUILD_MODNAME ":%s: " fmt, __func__
Remove function names from output
Use single line pr_debug instead of broken multiple uses without newline
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_open() will return without cleaning up net device or hardware state
if firmware loading fails. This results in a BUG() on a second attempt to
bring the interface up, reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even
worse effects if the driver is removed afterwards.
Call netdev_close() to clean up on failure.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15091
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Michael Moffatt <michael@moffatt.org.nz>
Tested-by: Michael Moffatt <michael@moffatt.org.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got below kernel oops when I try to bring down the network interface if
ftrace is enabled. The root cause is drv_ampdu_action() is passed with a
NULL ssn pointer in the BA session tear down case. We need to check and
avoid dereferencing it in trace entry assignment.
BUG: unable to handle kernel NULL pointer dereference
Modules linked in: at (null)
IP: [<f98fe02a>] ftrace_raw_event_drv_ampdu_action+0x10a/0x160 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[...]
Call Trace:
[<f98fdf20>] ? ftrace_raw_event_drv_ampdu_action+0x0/0x160 [mac80211]
[<f98dac4c>] ? __ieee80211_stop_rx_ba_session+0xfc/0x220 [mac80211]
[<f98d97fb>] ? ieee80211_sta_tear_down_BA_sessions+0x3b/0x50 [mac80211]
[<f98dc6f6>] ? ieee80211_set_disassoc+0xe6/0x230 [mac80211]
[<f98dc6ac>] ? ieee80211_set_disassoc+0x9c/0x230 [mac80211]
[<f98dcbb8>] ? ieee80211_mgd_deauth+0x158/0x170 [mac80211]
[<f98e4bdb>] ? ieee80211_deauth+0x1b/0x20 [mac80211]
[<f8987f49>] ? __cfg80211_mlme_deauth+0xe9/0x120 [cfg80211]
[<f898b870>] ? __cfg80211_disconnect+0x170/0x1d0 [cfg80211]
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 0b5ccb2(title:ipv6: reassembly: use seperate reassembly queues for
conntrack and local delivery) has broken the saddr&&daddr member of
nf_ct_frag6_queue when creating new queue. And then hash value
generated by nf_hashfn() was not equal with that generated by fq_find().
So, a new received fragment can't be inserted to right queue.
The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have seen RX stalls on a machine that experienced a suspected
OOM. After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side. As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.
The guest did not have a refill job scheduled.
My diagnosis is that an OOM had occured, with the delayed refill
job scheduled. The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.
As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.
The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.
Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this. Also, their buffers are
declared as variable-length arrays with no explicit maximum length.
Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics. Extend the stats
buffer to support this.
The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By rounding up the buffer size to power of 2, several expensive
modulus operations can be avoided. This patch also solves a bug where
the gap need when ring gets full was not being accounted for.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge tries to release regions even if they were not allocated.
This causes messages like the following in the kernel log
Trying to free nonexistent resource <00000000006af400-00000000006af4ff>
Trying to free nonexistent resource <00003c04ff9f4000-00003c04ff9f7fff>
Trying to free nonexistent resource <00003c04ffc00000-00003c04ffcfffff>
This patch fixes the goto logic in order to not release the resources
if they were not allocated.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Among other changes, this commit:
commit 06d0f0663e
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Thu Feb 12 10:06:45 2009 +0530
ath9k: Enable Fractional N mode
changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.
According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are a few station addresses that are
char *, instead of the normal u8 *; gcc
gives pointer signedness warnings for some
of those, so use u8 * consistently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GC is non-existent in netns, so after you hit GC threshold, no new
dst entries will be created until someone triggers cleanup in init_net.
Make xfrm4_dst_ops and xfrm6_dst_ops per-netns.
This is not done in a generic way, because it woule waste
(AF_MAX - 2) * sizeof(struct dst_ops) bytes per-netns.
Reorder GC threshold initialization so it'd be done before registering
XFRM policies.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obviously, this register had some other impact that is causing
the regression. Either it is masking some other access or needs
to be reset in some path.
Either, way it is best to just revert the change for 2.6.33
This reverts commit 166a0fd4c7.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Prémont found commit 9793241fe9
(vlan: Precise RX stats accounting) added a regression for non
hw accelerated vlans.
[ 26.390576] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 26.396369] IP: [<df856b89>] vlan_skb_recv+0x89/0x280 [8021q]
vlan_dev_info() was used with original device, instead of
skb->dev. Also spotted by Américo Wang.
Reported-By: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port. On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.
Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch from Sridhar Samudrala
The following patch fixes the check for IPv6 GSO packet in ixgbevf
driver to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
CC: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter whether connection track is enabled, an end host should send
an ICMPv4 "Fragment Reassembly Timeout" message when defrag timeout.
The reasons are following two points:
1. RFC 792 says:
>>>> >> > > If a host reassembling a fragmented datagram cannot complete the
>>>> >> > > reassembly due to missing fragments within its time limit it
>>>> >> > > discards the datagram, and it may send a time exceeded message.
>>>> >> > >
>>>> >> > > If fragment zero is not available then no time exceeded need be
>>>> >> > > sent at all.
>>>> >> > >
>>>> >> > > Read more: http://www.faqs.org/rfcs/rfc792.html#ixzz0aOXRD7Wp
2. Patrick McHardy also agrees with this opinion. :-)
About the discussion of this opinion, refer to http://patchwork.ozlabs.org/patch/41649
The patch fixed the problem like this:
When enabling connection track, fragments are received at PRE_ROUTING HOOK.
If they are failed to reassemble, ip_expire() will be called.
Before sending an ICMP "Fragment Reassembly Timeout" message,
the patch searches router table to get the destination entry only for host type.
The patch has been tested on both host type and route type.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct. The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simpily pass 'struct neigh_table' with seq_file private pointer,
and save one dereference. Proc entry itself isn't interesting.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After netdev_ops compat code HAVE_* macros aren't needed, in fact
they _will_ result in compile breakage for out of tree drivers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add igbvf to the list of supported Intel drivers and Alex to the list of
maintainers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF detects that the PF has reset turn off carrier and stop all
tx queues.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix panics in the VF driver that occur when you bring it down after
having already brought the PF down.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver gets a control message from the PF that indicates the
PF is about to reset or go down we schedule the watchdog timer so that
it will detect the PF has gone offline and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inadequate coordination between the PF driver and the VF driver results
in tx hangs in the VF driver when you perform certain actions that will
lead to a re-init of the PF. Add feature to notify active VFs when the PF
is about to re-initialize so that the VFs can take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF Reset Done bit should not be set in the extended control register
until the PF has actually completed the bring up process. It is a mis-
interpretation of the purpose of this bit to assume it should be set
when the physical reset of the device is done. Instead it should be used
to indicate to the VFs when the PF is ready to provide them with required
services. This is not until after the PF is finished coming up and ready
to process mailbox events.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This data storage for SW emulated MAC addresses is unlikely to ever be used
so pull it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are allocated (as indicated by adapter->num_vfs is non-zero) then
the PF pool is no longer zero. Instead it will be the same as the number
of VFs allocated. When setting the VLVF entry for the PF we need to use
the correct pool otherwise the PF will get VLAN packets from the wire
because the packet will pass VFTA filtering and the PF has the default
pool, but it will not get VLAN packets from the VFs because it has
not set the correct pool bit in the VLVF entry.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing the "e1000: enhance frame fragment detection" (and e1000e)
patches we found some bugs with reducing the MTU size. The 1024 byte
descriptor used with the 1000 mtu test also (re) introduced the
(originally) reported bug, and causes us to need the e1000_clean_tx_irq
"enhance frame fragment detection" fix.
So what has occured here is that 2.6.32 is only vulnerable for mtu <
1500 due to the jumbo specific routines in both e1000 and e1000e.
So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but
is not vulnerable to the original issue reported. It has been pointed
out that this vulnerability needs to be patched in older kernels that
don't have the e1000 jumbo routine. Without the jumbo routines, we
need the "enhance frame fragment detection" fix the e1000, old
e1000e is only vulnerable for < 1500 mtu, and needs a similar
fix. We split the patches up to provide easy backport paths.
There is only a slight bit of extra code when this fix and the
original "enhance frame fragment detection" fixes are applied, so
please apply both, even though it is a bit of overkill.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fmvj18x_cs, serial_cs:
add new id
Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first two fields of mcc wrb - embedded, payload_len
need to be cpu_to_le32() swapped while issuing a cmd to the hw.
The fields tag0, tag1 are opaque and returned back to cpu as is...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please add support for Microsoft MN-120 PCMCIA network card. It's an
old card, I know, but adding support is very easy. You just need to
get tulip_core.c to recognise its vendor/device ID.
Patch for kernel 2.6.32.4 (and many previous) attached.
.....Ron Murray
Signed-off-by: Ron Murray <rjmx@rjmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pages are posted to the rxq in such a way that more than one frag
can share the page. The last frag that uses the page unmaps the
page. In the case when a page is not fully used (due to lack of space in rxq)
the last frag that uses the page is not being set as a "last_page_user";
instead, the next frag in the rxq is incorrectly being set.
The fix has also been tested on ppc64 with 64k pages...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ddr dma ethtool self test needs to be performed even when ETH_TEST_FL_OFFLINE is not set.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel WiMax Wireless Link 6050 can show under more than one USB
ID. Add support for all, introducing a generic flag (i2400mu->i6050)
that denotes a 6x50 based device.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
sched: Fix vmark regression on big machines
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix race in tty_fasync
serial: serial_cs: oxsemi quirk breaks resume
serial: imx: bit &/| confusion
serial: Fix crash if the minimum rate of the device is > 9600 baud
serial-core: resume serial hardware with no_console_suspend
serial: 8250_pnp: use wildcard for serial Wacom tablets
nozomi: quick fix for the close/close bug
compat_ioctl: Supress "unknown cmd" message on serial /dev/console
