When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On the OMAP3, initialize SDRC timings when the kernel boots. This ensures
that the kernel is running with known, optimized SDRC timings, rather than
whatever was configured by the bootloader.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The original CDP kernel that this code comes from waited for 0x800
loops after switching the CORE DPLL M2 divider. This does not appear
to be necessary.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for keypad, GPIO keys and LEDs. Also enable hardware
debounce feature for GPIO keys.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Setup regulators for MMC1 and MMC2 to get those SD slots
working again.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
CC: David Brownell <david-b@pacbell.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialize regulators for Beagle and Overo.
Patch is based on earlier patches posted to linux-omap mailing
list.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Stanley.Miao <stanley.miao@windriver.com>
with board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Qimonda HYB18M512160AF-6 SDRAM chip, used on
the OMAP3430SDP boards.
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chip used on 3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add timing data for the Micron MT46H32M32LF-6 SDRAM chip, used on the
OMAP3 Beagle and EVM boards. Original timing data is from the Micron
datasheet PDF downloaded from:
http://download.micron.com/pdf/datasheets/dram/mobile/1gb_ddr_mobile_sdram_t48m.pdf
Thanks to Rajendra Nayak <rnayak@ti.com> for his help identifying
the chips used on Beagle & OMAP3EVM.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move platform_device_register() for serial device to
omap_serial_init()
There is no need to have arch_initcall() dependency in serial
as already board files call the function omap_serial_init()
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Hunyue Yau <hyau@mvista.com> with
board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Hunyue Yau <hyau@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.
Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.
Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes it possible to change uart sleep timeout. New sysfs
entry is added (/sys/devices/platform/serial8250.<uart>/sleep_timeout)
Writing zero will disable the timeout feature and prevent UART clocks
from being disabled.
Also default timeout is increased to 5 second to make serial console
more usable.
Original patch was written by Tero Kristo.
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add common omap2/3 function to check wether there is irq pending.
Switch to use it in omap2 pm code instead of its own.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 5461af5af5.
Adding a disable hook to the irq_chip is not the way to fix the
problem being addressed by this patch. Instead, we need to fix
support for [enable|disable]_irq_wake().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't necessarily want to compile in irq.o and sdrc.o for omap4.
Also, clock and prcm may not be implemented initially.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
