Move 4xx PHY_MODE_XXX defines to asm-ppc/ibm_ocp.h. This is a preparation
step for the new EMAC driver.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for the two PCI busses on MPC83xx and the MPC834x SYS/PIBS
reference board.
The code initializes PCI inbound/outbound windows, allocates and registers
PCI memory/io space. Be aware that setup of the PCI buses on the PIBs
board is expected to be done by the firmware.
Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for Marvell EV64360BP board. So far, it supports
mpsc serial console, gigabit ethernet, jffs2 root filesystem, etc. Other
device support, like watchdog, RTC, will be added later.
Signed-off-by: Lee Nicks <allinux@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable IBM405_ERR77 and IBM405_ERR51 errata workarounds for 405EP. This
chip has these problems fixed.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix STD_UART_OP definitions in Bamboo and Luan board ports which were
causing "initialization makes pointer from integer without a cast"
warnings.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix PowerPC NPe405H EMAC Tx channel assignments. EMAC unit in this chip
uses common for 4xx "two Tx / one Rx" configuration.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a field to struct ocp_func_emac_data that allows
platform-specific unsupported PHY features to be passed in to the ibm_emac
ethernet driver.
This patch also adds some logic for the Bamboo eval board to populate this
field based on the dip switches on the board. This is a workaround for the
improperly biased RJ-45 sockets on the Rev. 0 Bamboo.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support ochi-ppc-soc.c on IBM stb04xxx platforms
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the PCORE board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the SPD823TS board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the SM850 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the OAK board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the MENF1 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the MCPN765 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the K2 board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the ASH board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the ADIR board is no longer maintained and thus being removed
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PM is broken on 44x; removed duplicate entry for CONFIG_PM, made
the inclusion of generic one conditional on BROKEN || !44x.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add PPC440EP core support. PPC440EP is a PPC440-based SoC with a classic PPC
FPU and another set of peripherals.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix 44x early serial debugging for big RAM configurations (more than 512M).
We cannot use default OpenBIOS virtual mapping, because it interferes with
pinned TLB entry.
While we are at it, move early UART mapping to TLB slot 0, so it can
survive longer during boot process (slot 1 is used by the first ioremap
call, effectively killing UART mapping if it occupies this slot). Also,
change UART TLB entry size to 4K (256M is too much for a bunch of registers
:). Squash some warnings on the way.
Tested on Ebony and Ocotea with 1G of RAM.
Thanks to Scott Coulter <scott.coulter@cyclone.com> for diagnosing this
problem.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added missing include of cpm2.h in correct order to allow TQM8260 to build
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the MAL channels count in PPC 440SP OCP definition. PPC 440SP has only
1 EMAC attached to MAL.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updated prpmc750 platform code to include serial_reg.h to fix building.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The UARTs on the MPC824x are unique devices and really shouldn't be thought
of as a DUART. In addition, if both UARTs are in use we need to configure
the part to enable the 2nd UART since the pins for the UARTs are
multiplexed. Adds support to run the 824x Sandpoint with both UARTs if
desired.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added a proper prototype for cpm2_reset() which gets rid of a build
warning.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix u32 vs pm_message_t confusion in cpufreq.
Signed-off-by: Bernard Blackham <bernard@blackham.com.au>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Freescale MPC86xADS board support. The supported
devices are SMC UART and 10Mbit ethernet on SCC1.
The manual for the board says that it "is compatible with the MPC8xxFADS
for software point of view". That's why this patch extends FADS instead of
introducing a new platform.
FEC is not supported as the "combined FCC/FEC ethernet driver" driver by
Pantelis Antoniou should replace the current FEC driver.
Signed-off-by: Gennadiy Kurtsman <gkurtsman@ru.mvista.com>
Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Editor snafu in which the call to ppc_sys_get_pdata got inside the if check
instead of before it. Oops.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes CONFIG_PMAC_PBOOK (PowerBook support). This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Lost a curly brace in translation. Everything is better now.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Continue the Good Fight: Limit bootmem.h include creep.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ensure that the returned pointer from ppc_sys_get_pdata is not NULL before we
start using it. This handles any cases where we have variants of processors
on the same board with different functionality.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adding support for MPC8548 w/o PCI support, broke building MPC8555 CDS
by trying to remove a loop variable that was used when PCI is enabled.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org)
This change provides support for the DS1374 Real-Time Clock chip present
on the MPC8349ADS board. It depends on a previous patch which adds I2C
support for the DS1374.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fight the Good Fight: Limit prom.h header creep.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Made the number of TLB CAM entries private and converted the board
consumers to use num_tlbcam_entries which is setup at boot time from
configuration registers. This way the only consumers of the #define
NUM_TLBCAMS are the arrays used to manage the TLB.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The MPC8548 has 48 internal interrupts and 12 external interrupts. The
previous generation PowerQUICC III devices only had 32 internal and 12
external interrupts on the primary interrupt controller.
Expanded the number of internal interrupts to 48 for all PowerQUICC III
processors and moved the interrupt numbers for the external after the 48
internal interrupt lines, rather than putting the 12 new internal
interrupts at the end and ifdef'ng the whole mess. As parted of this
created a macro which represents the internal interrupt senses since they
are the same on all PQ3 processors.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Added platform device initialization for the two 8250 style UARTs that
exist on the MPC8245. Additionally, updated the Sandpoint code to enable
one of these UARTs if an MPC8245 is connected to it.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds support for using the MPC8548 processor on the CDS reference board.
Currently all the major busses (PCI, PCI-X, PCI-Express, sRIO) and eTSEC3
and eTSEC4 are not supported.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Despite all the care lately in making the powermac sleep/wakeup as
robust as possible, there is still a nasty related to the use of cpufreq
on PMU based machines. Unfortunately, it affects paulus old powerbook
so I have to fix it :)
We didn't manage to understand what is precisely going on, it leads to
memory corruption and might have to do with RAM not beeing properly
refreshed when a cpufreq transition is done right before the sleep.
The best workaround (and less intrusive at this point) we could come up
with is included in this patch. We basically do _not_ force a switch to
high speed on suspend anymore (that is what is causing the problem) on
those machines. We still force a speed switch on wakeup (since we don't
know what speed we are coming back from sleep at, and that seems to work
fine).
Since, during this short interval, the actual CPU speed might be
incorrect, we also hack around by multiplying loops_per_jiffy by 2 (max
speed factor on those machines) during early wakeup stage to make sure
udelay's during that time aren't too short.
For after 2.6.12, we'll change udelay implementation to use the CPU
timebase (which is always constant) instead like we do on ppc64 and thus
get rid of all those problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trying to initialize the i8259 PIC will not work if CONFIG_PCI is not
enabled. The kernel hangs if the initialization is tried.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change allows mpc83xx_restart to issue a software reset.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The call to io_block_mapping was creating an invalid BAT entry because the
value of BCSR_SIZE (32K) is too small to be used in a BAT (128K min). This
change removes the io_block_mapping call since these registers can easily
be mapped using ioremap at the point of use.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch that introduced support for the VIA chipset broke building if
CONFIG_PCI is disabled.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds on-chip PCI bridge support for the PQ2 family. The
incomplete existent code is updated with interrupt handling stuff and
board-specific bits for 8272ADS and PQ2FADS; the related files were renamed
(from m8260_pci to m82xx_pci) to be of more generic fashion. This is
tested with 8266ADS and 8272ADS, should work on PQ2FADS as well.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the VIA IDE controller that exists on the MPC8555 CDS
system. Updated the config for the system to enable support by default.
Signed-off-by: Scott Hall <shall@mvista.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some debug registers needed to be initialized early on to allow proper
support for KGDB. Additionally, we need to setup the
ppc.md_early_serial_map function pointer on boards that have serial support
for KGDB.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent kernels occasionally trigger a PMU timeout on some mac laptops,
typically on wakeup from sleep. This seem to be caused by either a too big
latency caused by the cpufreq switch on wakeup from sleep or by an
interrupt beeing lost due to the reset of the interrupt controller done
during wakeup.
This patch makes that code more robust by stopping PMU auto poll activity
around cpufreq changes on machines that use the PMU for such changes (long
latency switching involving a CPU hard reset and flush of all caches) and
by removing the reset of the open pic interrupt controller on wakeup (that
can cause the loss of an interrupt and Darwin doesn't do it, so it must not
be necessary).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a missing attribute to pmac cpufreq so that
"scaling_available_frequencies" works. It also cleans up the duplicate
definitions for low and high speed constants.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: John Clemens <clemej@alum.rpi.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The clock spreading disable/enable code was called to late/early during
the suspend/resume code on some laptops and would trigger a
might_sleep() warning due to the down() call in the low level i2c code.
This fixes it by calling those functions earlier/later when interrupts
are still enabled.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A typo in the machine table incorrectly mark the 101 PowerBook as
needing explicit callback from the video driver to enable sleep mode. I
did not implement that mecanism for chipsest older than r128, so we need
to mark this machine as always beeing able to sleep for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We are experiencing a problem when flushing the CPU caches before sleep
on some laptop models using the 750FX CPU rev 1.X. While I haven't been
able to figure out a proper explanation for what's going on, I do have a
workaround that seem to work reliably and allows those machine to sleep
and wakeup properly again.
I'll re-update that code if/when I ever find exactly what is happening
with those CPU revisions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some earlier models of aluminium powerbooks and ibook G4s have a clock chip
that requires some tweaking before and after sleep. It seems that without
that magic incantation to disable and re-enable clock spreading, RAM isn't
properly refreshed during sleep. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the hooks into the PPC7D platforms file to support the DS1337
RTC device as the clock device for the PPC7D board.
Signed-off-by: Chris Elston <chris.elston@radstone.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the SDRAM output from /proc/cpuinfo. The previous code
assumed that there was only one bank of SDRAM, and that the size in the memory
configuration register was the total size.
Signed-off-by: Chris Elston <chris.elston@radstone.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some G3 CPUs can crash in funny way if a store from an FPU register
instruction is executed on a register that has never been initialized since
power on. This patch fixes it by making sure all FP registers have been
properly initialized at kernel boot and when waking from sleep. It also makes
the code that decides wether HID0_BTIC and HID0_DPM are allowed on a given CPU
smarter (it can actually _clear_ them now if they are not allowed instead of
just setting them when they are allowed in case the firmware got them wrong)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* ->io_base_virt in struct pci_controller is iomem pointer. Marked as such.
Most of the places that used it are already annotated to expect iomem.
* places that did gratitious (and wrong) casts a-la
isa_io_base = (unsigned long)ioremap(...);
hose->io_base_virt = (void *)isa_io_base;
turned into
hose->io_base_virt = ioremap(...);
isa_io_base = (unsigned long)hose->io_base_virt;
* pci_bus_io_base() annotated as returning iomem pointer.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hacks the current PowerMac Alsa driver to add some basic support
of analog sound output to some desktop G5s. It has severe limitations
though:
- Only 44100Khz 16 bits
- Only work on G5 models using a TAS3004 analog code, that is early
single CPU desktops and all dual CPU desktops at this date, but none
of the more recent ones like iMac G5.
- It does analog only, no digital/SPDIF support at all, no native
AC3 support
Better support would require a complete rewrite of the driver (which I am
working on, but don't hold your breath), to properly support the diversity
of apple sound HW setup, including dual codecs, several i2s busses, all the
new codecs used in the new machines, proper clock switching with digital,
etc etc etc...
This patch applies on top of the other PowerMac sound patches I posted in
the past couple of days (new powerbook support and sleep fixes).
Note: This is a FAQ entry for PowerMac sound support with TI codecs: They
have a feature called "DRC" which is automatically enabled for the internal
speaker (at least when auto mute control is enabled) which will cause your
sound to fade out to nothing after half a second of playback if you don't
set a proper "DRC Range" in the mixer. So if you have a problem like that,
check alsamixer and raise your DRC Range to something reasonable.
Note2: This patch will also add auto-mute of the speaker when line-out jack
is used on some earlier desktop G4s (and on the G5) in addition to the
headphone jack. If that behaviour isn't what you want, just disable
auto-muting and use the manual mute controls in alsamixer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch restores the original behaviour of prep_pcibios_fixup() to only
call prep_pib_init() on machines with an openpic. This allows the
Powerstack II Pro4000 to boot again.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When building a ppc32 MULTIPLATFORM kernel for a 64bit pmac, we try and
build certain files or use certain functions that make no sense in that
context. This catches the last of these.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following problem was found by Giovambattista Pulcini
<gpulcini@swintel.it>, who also provided a partial patch, and this has been
verified by our time guru Gabriel Paubert <paubert@iram.es>.
The problem is that in do_settimeofday() we always set time_state to
TIME_ERROR and except on two platforms, never re-set it. This meant that
ntp_gettime() and ntp_adjtime() always returned TIME_ERROR, incorrectly.
Based on Gabriel's analysis, time_state is used for leap-second processing,
and ppc shouldn't be mucking with it.
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My previous patch that added sleep support for uninorth-agp and some AGP
"off" stuff in radeonfb and aty128fb is breaking some configs. More
specifically, it has problems with rage128 setups since the DRI code for
these in X doesn't properly re-enable AGP on wakeup or console switch
(unlike the radeon DRM).
This patch fixes the problem for pmac once for all by using a different
approach. The AGP driver "registers" special suspend/resume callbacks with
some arch code that the fbdev's can later on call to suspend and resume
AGP, making sure it's resumed back in the same state it was when suspended.
This is platform specific for now. It would be too complicated to try to
do a generic implementation of this at this point due to all sort of weird
things going on with AGP on other architectures. We'll re-work that whole
problem cleanly once we finally merge fbdev's and DRI.
In the meantime, please apply this patch which brings back some r128 based
laptops into working condition as far as system sleep is concerned.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the PowerMac cpufreq driver. It depends on the addition
of the suspend() method (my previous patch) and on the new flag I defined
to silence some warnings that are normal for us.
It fixes various issues related to cpufreq on pmac, including some crashes
on some models when sleeping the machine while in low speed, proper voltage
control on some newer machines, and adds voltage control on 750FX based G3
laptops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the procedure in the ppc32 kernel that synchronizes the timebase
registers across an SMP powermac system does so by setting both timebases
to zero. That is OK at boot but causes problems if done later. So that we
can do hotplug CPU on these machines, this patch changes the code so it
reads the timebase from one CPU and transfers the value to the other CPU.
(Hotplug CPU is needed for sleep (aka suspend to RAM) to work.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
