* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix bogus dma mapping
ieee1394: sbp2: pass REQUEST_SENSE through to the target
fix an GFP_KERNEL allocation in atomic section: kvm_dev_ioctl_create_vcpu()
called kvm_mmu_init(), which calls alloc_pages(), while holding the vcpu.
The fix is to set up the MMU state in two phases: kvm_mmu_create() and
kvm_mmu_setup().
(NOTE: free_vcpus does an kvm_mmu_destroy() call so there's no need for any
extra teardown branch on allocation/init failure here.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__free_page() doesn't like a NULL argument, so check before calling it. A
NULL can only happen if memory is exhausted during allocation of a memory
slot.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
No need to append _MSR to msr names, a prefix should suffice.
Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These msrs are referenced by benchmarking software when pretending to be an
Intel cpu.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest version of kvm doesn't initialize kvm_arch_ops in kvm_init(), which
causes an error with the following sequence.
1. Load the supported arch's module.
2. Load the unsupported arch's module.$B!!(B(loading error)
3. Unload the unsupported arch's module.
You'll get the following error message after step 3. "BUG: unable to handle
to handle kernel paging request at virtual address xxxxxxxx"
The problem here is that the unsupported arch's module overwrites kvm_arch_ops
of the supported arch's module at step 2.
This patch initializes kvm_arch_ops upon loading architecture specific kvm
module, and prevents overwriting kvm_arch_ops when kvm_arch_ops is already set
correctly.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of doing tricky stuff with the arch dependent virtualization
registers, take a peek at the guest's efer.
This simlifies some code, and fixes some confusion in the mmu branch.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
current_cpu_data invokes smp_processor_id(), which is inadvisable when
preemption is enabled. Switch to boot_cpu_data instead.
Resolves sourceforge bug 1621401.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fallback to PIO mode in the hwif->dma_check() handler doesn't work in
the Intel PIIX and SMsC SLC90E66 IDE drivers because:
- config_drive_for_dma() calls the hwif->speedproc() handler with a wrong
mode number (unbiased by XFER_PIO_0) in case of the PIO fallback;
- hwif->tuneproc() handler doesn't really set the drive's own speed (this
is not fixed as yet).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no need to check in piix_config_drive_for_dma() for broken MW DMA
mode 0 as this mode is not supported by the driver (it sets
hwif->mwdma_mask to 0x6), and hence can't be selected by ide_dma_speed().
(Alan sayeth "Probably right but if not you've got a subtle corruptor. Should
at least stick a BUG_ON mode 0 setting right close when the mode is set.")
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Russel King recently reminded us that one shouldn't use asm/arch/hardware.h
but one should use asm/hardware.h. Unfortunately, the spi_s3c24xx_gpio
driver is using the wrong header. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Return a fault code if the Dataflash driver runs into a "no device present"
error when the MISO line has a pulldown (it currently expects a pullup), so
that rmmod won't oops.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix build issues that show up with the m25p80 SPI flash driver when
building with MTD debug enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some issues were recently turned up with the current specification of what
it means for spi_transfer.tx_buf to be null, as part of transfers which are
(from the SPI protocol driver perspective) pure reads.
Specifically, that it seems better to change the TX behaviour there from
"undefined" to "will shift zeroes". This lets protocol drivers (like the
ads7846 driver) depend on that behavior. It's what most controller drivers
in the tree are already doing (with one exception and one case of driver
wanting-to-oops), it's what Microwire hardware will necessarily be doing,
and it removes an issue whereby certain security audits would need to
define such a value anyway as part of removing covert channels.
This patch changes the specification to require shifting zeroes, and
updates all currently merged SPI controller drivers to do so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RAID_UNKNOWN is used even when PROC_FS=n, so move it outside of the
CONFIG_PROC_FS block.
drivers/block/cciss.c:1910: error: 'RAID_UNKNOWN' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many spinlock recursion was in the isicom driver. Eliminate it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The apple fn keys don't work anymore with 2.6.20-rc1.
The reason is that USB_HID_POWERBOOK appears in several files although
USB_HIDINPUT_POWERBOOK is the thing to be used.
The patch fixes this.
Cc: Greg KH <greg@kroah.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit bed8bdfd ("IB: kmemdup() cleanup") introduced one bad conversion to
kmemdup() in mthca_alloc_fmr(), where the structure allocated and the
structure copied are not the same size. Revert this back to the original
kmalloc()/memcpy() code.
Reported-by: Dotan Barak <dotanb@mellanox.co.il>.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tty_driver->owner is not set, so if somebody remove mxser_module, it might
oops (and doesn't tell the user: no way, it's in use). Set the .owner value.
Cc: <osv@javad.com>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't have macros between a function's kernel-doc block and the function
definition. This is not valid for kernel-doc.
Warning(/var/linsrc/linux-2.6.20-rc1-git8//drivers/pci/probe.c:653): No description found for parameter 'IORESOURCE_PCI_FIXED'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Choose rpa_vscsi.c over iseries_vscsi.c when building both pseries and
iseries. This fixes a link error.
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_param_str() cannot use kstrdup() to duplicate the parameter. That's
fine when the driver is compiled as a module but it sure is not when built
into the kernel as the kernel parameters are parsed before the kmalloc
slabs are setup.
Signed-off-by: Sebastien Dugué <sebastien.dugue@bull.net>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to use a PCI device, not a FireWire host device. Problem found by
Andreas Schwab, mistake pointed out by Benjamin Herrenschmidt.
http://ozlabs.org/pipermail/linuxppc-dev/2006-December/029595.html
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Andreas Schwab <schwab@suse.de>
Delete some incorrect code, left over from the initial driver submission
in March 2001.
SBP-2 targets should provide sense data via the SBP-2 status block
(autosense). We have to pass the REQUEST_SENSE command through to
targets which don't implement autosense, if there are any, and to
accomodate application clients which use this command.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (28 commits)
V4L/DVB (5010): Cx88: Fix leadtek_eeprom tagging
V4L/DVB (5012): Usbvision fix: It was using "&&" instead "&"
V4L/DVB (5001): Add two required headers on kernel 2.6.20-rc1
V4L/DVB (5014): Allyesconfig build fixes on some non x86 arch
V4L/DVB (4997): Bttv: delete duplicated ioremap()
V4L/DVB (4996): Msp3400: fix kthread_run error check
V4L/DVB (4995): Vivi: fix kthread_run() error check
V4L/DVB (4994): Vivi: fix use after free in list_for_each()
V4L/DVB (4992): Fix typo in saa7134-dvb.c
V4L/DVB (4991): Cafe_ccic.c: fix NULL dereference
V4L/DVB (4990): Cpia2/cpia2_usb.c: fix error-path leak
V4L/DVB (4988): Cx2341x audio_properties is an u16, not u8
V4L/DVB (4984): LOG_STATUS should show the real temporal filter value.
V4L/DVB (4983): Force temporal filter to 0 when scaling to prevent ghosting.
V4L/DVB (4982): Fix broken audio mode handling for line-in in msp3400.
V4L/DVB (4980): Fixes bug 7267: PAL/60 is not working
V4L/DVB (4979): Fixes compilation when CONFIG_V4L1_COMPAT is not selected
V4L/DVB (4973): Dvb-core: fix printk type warning
V4L/DVB (4972): Dvb-core: fix bug in CRC-32 checking on 64-bit systems
V4L/DVB (4970): Usbvision memory fixes
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (42 commits)
r8169: extraneous Cmd{Tx/Rx}Enb write
forcedeth: modified comment header
NetXen: Reducing ring sizes for IOMMU issue.
NetXen: Fix for PPC machines.
NetXen: work queue fixes.
NetXen: Link status message correction for quad port cards.
NetXen: Multiple adapter fix.
NetXen: Using correct CHECKSUM flag.
NetXen: driver reload fix for newer firmware.
NetXen: Adding new device ids.
PHY probe not working properly for ibm_emac (PPC4xx)
ep93xx: some minor cleanups to the ep93xx eth driver
sky2: phy power down needs PCI config write enabled
sky2: power management/MSI workaround
sky2: dual port NAPI problem
via-velocity uses INET interfaces
e1000: Do not truncate TSO TCP header with 82544 workaround
myri10ge: handle failures in suspend and resume
myri10ge: no need to save MSI and PCIe state in the driver
myri10ge: make msi configurable at runtime through sysfs
...
Copy inline assembly of stsch and add "memory" to clobber list in order
to prevent gcc from optimizing away the checking of the global variable
"pgm_check_occured".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce the max. buffer size for the monwriter device to prevent a
possible problem with the z/VM monitor service.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
reference to .init.text: from .text between 'cx88_card_setup'
(at offset 0x68c) and 'cx88_risc_field'
Caused by leadtek_eeprom() being declared __devinit and called from
a non-devinit context.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
include/media/ir-common.h:78: error: field 'work' has incomplete type
drivers/media/common/ir-functions.c: In function 'ir_rc5_timer_end':
drivers/media/common/ir-functions.c:301: error: 'jiffies' undeclared (first use in this function)
drivers/media/common/ir-functions.c:301: error: (Each undeclared identifier is reported only once)
drivers/media/common/ir-functions.c:301: error: for each function it appears in.)
drivers/media/common/ir-functions.c:347: error: 'HZ' undeclared (first use in this function)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- CAFE_CCIC needs to depend on PCI, else "allyesconfig" breaks
on systems without PCI
- em28xx-video can't udelay(2500) else "allyesconfig" breaks
on systems that refuse to spin that long (I saw it on ARM)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ioremap() is called twice to same resource.
The returen value of first one is not error-checked.
second one is complely ignored.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of kthread_run() should be checked by IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of kthread_run() should be checked by IS_ERR().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Freeing data including list_head in list_for_each() is not safe.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We shouldn't dereference "cam" when we already know it's NULL.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The temporal filter is forced off when scaling. The VIDIOC_LOG_STATUS
handler still showed the old temporal filter. It is now consistent with
the real temporal filter value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the code to unconditionally turn off the temporal filter when scaling.
If the window is not full screen the filter will introduce a nasty ghosting
effect.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The wrong matrix was used when an external input was selected instead of
the tuner input. The rxsubchans field was also not initialized to STEREO
for an external input. And finally the msp34xxg_detect_stereo() should
not try to detect stereo for an external input, that code is for the
tuner input only.
Together these bugs made it hit 'n miss whether you ever got stereo out
of the msp3400 for an external input.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On cx88 driver, sampling rate should be at chroma subcarrier freq (FSC).
However, driver were programming wrong values for PAL/60, PAL/Nc and
NTSC 4.43. This patch do the proper calculation. It also calculates
htotal, hdelay and hactive constants, according with the sampling
rate.
It is tested with PAL/60 by Piotr Maksymuk and Olivier. Also tested with
the already-supported standards.
Test is still required for PAL/Nc.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- SYSFS: Replaced all to_video_device(cd), video_device_create_file,
video_device_remove_file and add the proper checks at create_file
- Converted old norm values to V4L2 ones.
- Robustness on sysfs hue/contrast/saturation queries.
Additional check in order to return 0 if the driver is not opened.
- Whitespace cleanups in usbvision-cards.c
This patch merges two fixes by Thierry MERLE and Mauro Chehab, and adds
additional checks.
Signed-off-by: Dwaine Garden<DwaineGarden@rogers.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb_net.c: In function 'dvb_net_ule':
dvb_net.c:628: warning: format '%#lx' expects type 'long unsigned int', but argument 3 has type 'u32'
dvb_net.c:628: warning: format '%#lx' expects type 'long unsigned int', but argument 4 has type 'u32'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CRC-32 checking during ULE decapsulation always failed on x86_64 systems due
to the size of a variable used to store CRC. This bug was discovered on
Fedora Core 6 with kernel-2.6.18-1.2849. The i386 counterpart has no such
problem. This patch has been tested on 64-bit system as well as 32-bit system.
Signed-off-by: Ang Way Chuang <wcang@nrg.cs.usm.my>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
