Although according to the documentation this largely only affects
desktop LED control, let's make sure we set the ATAPI bit when we
have an ATAPI device attached to the port.
scsi_wait_req does not exist any more in the SCSI layer. This patch
makes it so libata can compile again.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will let me chop the code size of several drivers right down. In
many cases the actual private data is very useful and constant for a
given host controller so being able to just pass it at probe time would
be very useful indeed (eg with the via driver would could pass the udma
clocking and reduce the code size, or with the AMD one the UDMA
multiplier and the offset)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Current upstream 'allmodconfig' build is broken. This is the obvious
patch...
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch started life as a response to fedora specific ide subsystem changes
that made error handling of my ATAPI tape drive fail; the specifics are in
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=160868
The insertion of the statement rq->errors = err; near the end of
ide_end_drive_cmd() in drivers/ide/ide-io.c means that rq->errors does not
contain what it needs to in idescsi_end_request() in drivers/scsi/ide-scsi.c
anymore. Recent mainline kernels now also have this change.
The patch below makes ide-scsi whole.
Signed-off-by: Willem Riede <wrlk@riede.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A driver must wait 100us before attempting an MMIO operation
to the RISC after a soft-reset has been initiated. A
similar delay was needed with earlier ISPs.
Note: a PCI config-space read is used to flush the MMIO
write to the ISP, since the ISP's state machines are unable
to respond to any MMIO read during the reset process.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct issue where abort I/O command was not being issued
when the loop-state was down.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When mulitple initiators are coming up in an FCAL topology.
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On MMIO relaxed-order platforms, it is possible for the
proper delay during NVRAM access to begin before the request
passes through the PCI bus (via a MMIO write) to the ISP.
Thus, causing a subsequent read to the NVRAM part to fail.
Add a MMIO read, after the MMIO write to insure any posted
writes are flushed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
The return data from a read capacity 16 needs to have RTO_EN and PROT_EN
zeroed out.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sd_issue_flush() is called from atomic context so we can't use the
semaphore based routines to get a reference to the scsi_disk. Assume
something else already got the reference so we can safely use it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- if condition fix for ata_dev_identify()
- ata_pio_poll() minor cleanup.
Changes:
- Use (dev->class == ATA_DEV_ATA) for ata_dev_identify()
since "qc->tf.command" has been overwritten by the device status
- Use HSM_ST_TMOUT directly in ata_pio_poll()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The problem is that scsi_run_queue is called from scsi_next_command()
after doing a scsi_put_command. If the command was the only thing
holding the reference on the scsi_device then the resulting device put
will tear down the block queue. Fix this by taking a reference to the
device and holding it around scsi_run_queue()
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the drivers/scsi/ part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/scsi/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix more include file problems that surfaced since I submitted the previous
fix-missing-includes.patch. This should now allow not to include sched.h
from module.h, which is done by a followup patch.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some new ipr adapters do not support some of the initialization
commands currently sent to it from the driver. Handle these
commands failing and continue on with the adapter initialization.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increase device scanning limits so that all devices are found.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Support now exists in some ipr adapters to issue a device reset
to an Advanced Function disk.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New ipr adapters support a new device queueing model in the
adapter firmware. The queueing model is the NACA queueing model,
but it does not mean use of NACA is required. The new model removes
some of the adapter firmware queue state that made handling QERR=0
almost impossible. The queueing model on older adapters included the
concept of a queue frozen state, which would freeze the response
queue in the adapter when a check condition occurred, requiring a
a primitive to resume the queue. The new queueing model removes this
complexity.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Handle some new types of ipr errors that can be returned by the adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some newer ipr adapters are capable of returning autosense from
devices that support it. This patch adds the data structures for
the autosense buffer.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some ipr adapters will automatically create single device
RAID 0 arrays for all unconfigured RAID capable devices found
at adapter initialization time. This patch adds a module parameter
to disable this behavior.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some IPR RAID adapter will automatically create single device RAID arrays
for all attached devices when the card is initialized. Setting the
RUNTIME_RESET doorbell bit will prevent this from occurring, since we
only want this behavior the first time the card is initialized and not
each time the card happens to get reset.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add support for handling some new errors that may be returned
by ipr adapters.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If an ipr adapter repeatedly fails its initialization
the ipr driver will take the adapter offline and never talk
to it again. This provides a method for the user to manually
try the initialization again through sysfs.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some compile time debugging options runtime module options.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the write buffer command that is issued to the ipr adapter
to update its microcode fails for some reason, the DMA buffer
will never get unmapped. Move the pci_map/unmap out of the
IOA reset job so that the buffer is always clearly mapped
and unmapped.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert appropriate kmalloc/memset calls to use kzalloc.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds a scsi_host sysfs attribute and module parm to enable/disable
the write cache on an ipr adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Optimize ipr's slave_alloc to return -ENXIO for devices that
do not exist.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set the no_uld_attach for devices ipr does not want
upper layer drivers to attach to. These devices are
only reported for RAID management and only sg should
be used to talk to them.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix ipr to include all disks in the supported device list,
not just disks formatted to advanced function format.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify error logging path, sanitize error length returned
by the adapter.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Better handle errors received which are not known to the device driver.
Just dump the hex data so that we have a hope of figuring out what
went wrong.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The generic ipr adapter error log currently logs 2 lines of useless
data. Delete these lines.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adds a macro in the ipr driver for logging a physical device location.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify the ipr error structures a bit by removing some duplication.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IPR RAID arrays show up on a virtual scsi bus, with a scsi bus number
of 255, which is generated by the adapter microcode. For the initial
scan of the host, we manually scan this bus since it does not obey
SAM in regards to sparse LUNs and the disk array devices do not have
a consistent product id to use scsi core's blacklist. If /proc/scsi/scsi
or sysfs is used to delete one of these devices, the device will not
be able to get added back by rescanning the host since scsi core
will see ipr's max_channel as 4, rather than 255. Update max_channel
after the initial scan so that ipr raid arrays can get re-added
if they get deleted.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SCSI qlogicisp driver is both marked BROKEN and superseded by the
qla1280 driver.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the internal lock in queuecommand instead. also switch
the only direct use of the internal lock to the wrappers used elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the internal lock in queuecommand instead. also switch
the only direct use of the internal lock to the wrappers used elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the adapter lock in megaraid_queue. Additional benefit is
that we can get rid of the awkward conditional locking in
mega_internal_command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
also remove the adapter->host_lock alias for adapter->lock and remove
some superflous locking aswell as removing the tiny locking wrappers
for the EH routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
recent kernels call the eh_ methods without the host lock held.
megaraid_sas doesn't need it but drops it before calling a sleeping
routine and reqcquires it afterwards. Just remove the
spin_unlock/spin_lock calls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_send_eh_cmnd currently uses a semaphore and an overload of eh_timer
to either get a completion for a command for a timeout.
Switch to using a completion and wait_for_completion_timeout to simply
the code and not having to deal with the races ourselves.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This function has been superceeded by the block request based interfaces
and is unused (except for the uncompilable cpqfc driver).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
now that the abuse in qla2xxx is gone this field can be remove.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
adjust comments, remove a useless cast and remove a write-only variable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch started life as a response to fedora specific ide subsystem changes
that made error handling of my ATAPI tape drive fail; the specifics are in
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=160868
The insertion of the statement rq->errors = err; near the end of
ide_end_drive_cmd() in drivers/ide/ide-io.c means that rq->errors does not
contain what it needs to in idescsi_end_request() in drivers/scsi/ide-scsi.c
anymore. Recent mainline kernels now also have this change.
Signed-off-by: Willem Riede <wrlk@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
IBM has finally agreed that the "Version Matching" between firmware and
drivers ( and the resulting warning messages ) is no longer necessary.
This patch will remove those functions from the ServeRAID driver.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Update raid class to use nested classes for raid components (this will
allow us to move to a component control model now)
- Make the raid level an enumeration rather than and int.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's an oops that sometimes shows up with SCSI transport classes in
sysfs_hash_and_remove. The problem is that now, because of the class to
device and vice versa symlinks, all classes have to be removed from
visibility *before* the device is removed from visibility.
The transport class trigger points violate this, so bring them back into
conformance.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently the driver takes a reference only for requests coming by way
of the gendisk, not for requests coming by way of the struct device or
struct scsi_device. Such requests can arrive in the rescan, flush,
and shutdown pathways.
The patch also makes the scsi_disk keep a reference to the underlying
scsi_device, and it erases the scsi_device's pointer to the scsi_disk
when the scsi_device is removed (since the pointer should no longer be
used).
This resolves Bugzilla entry #5237.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
If I/O is active on the adapter, and an unexpected interrupt is pending
during initialization, the driver blows it's brains out. Since the driver
didn't initiate the I/O, the data in it's internal tables will contain NULL
pointers.
When this condition is detected, a "flush cache and reset" is performed.
The flush cache allows any pending "lazy writes" that the adapter is
processing to complete ( a "must have" for a RAID adapter ) and the reset
puts the adapter back into a known, good state.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jeff Garzik <jgarzik@pobox.com> points out that this was wrong: we need to
disable local interrupts while holding KM_IRQ0 due to IRQ sharing.
And holding interrupts off during a big PIO opration is expensive, so we only
want to do that if we know the page was highmem.
So revert commit 17fd47ab4d
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of power packed into a little patch.
This change eliminates the sharing between our controller-wide spinlock
and the SCSI core's Scsi_Host lock. As the locking in libata was
already highly compartmentalized, always referencing our own lock, and
never scsi_host::host_lock.
As a side effect, this change eliminates a deadlock from calling
scsi_finish_command() while inside our spinlock.
Integrate ata_exec() and ata_tf_to_host() into their only caller,
ata_bus_edd().
Rename ata_tf_to_host_nolock() to ata_tf_to_host().
This makes locking a bit easier to review, and may help pave the way for
future changes.
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(akpm: I don't do typo patches, but one of these is in a printk string)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's not necessary to test PageHighmem in here - kmap_atomic() does the right
thing.
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ata_pci_init_one() receives an array of struct ata_port_info. Recent
updates to the code had always obtained port information from
array element 0, rather than array element N.
Change to avoid hardcoding port_info[0], thereby restoring proper
hardware information to secondary legacy ports.
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
Remove PageReserved() calls from core code by tightening VM_RESERVED
handling in mm/ to cover PageReserved functionality.
PageReserved special casing is removed from get_page and put_page.
All setting and clearing of PageReserved is retained, and it is now flagged
in the page_alloc checks to help ensure we don't introduce any refcount
based freeing of Reserved pages.
MAP_PRIVATE, PROT_WRITE of VM_RESERVED regions is tentatively being
deprecated. We never completely handled it correctly anyway, and is be
reintroduced in future if required (Hugh has a proof of concept).
Once PageReserved() calls are removed from kernel/power/swsusp.c, and all
arch/ and driver code, the Set and Clear calls, and the PG_reserved bit can
be trivially removed.
Last real user of PageReserved is swsusp, which uses PageReserved to
determine whether a struct page points to valid memory or not. This still
needs to be addressed (a generic page_is_ram() should work).
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap (and
thus mapcounted and count towards shared rss). These writes to the struct
page could cause excessive cacheline bouncing on big systems. There are a
number of ways this could be addressed if it is an issue.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Refcount bug fix for filemap_xip.c
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch uses sg_set_buf/sg_init_one in some places where it was
duplicated.
Signed-off-by: David Hardeman <david@2gen.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trivial iomem annotations + missing memcpy_fromio() caught by
those
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
libata-core cleanups:
- use kzalloc() instead of kmalloc() + memset();
- use one exit path in ata_device_add();
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
We want ->tf_read() to get a complete snapshot of all taskfile
registers, without requiring the callers to manually call
ata_chk_status() and ata_chk_err() themselves.
This also fixes a minor bug in sata_vsc where the lower bits of the
feature register were incorrectly placed in the HOB (high order bits)
portion of struct ata_taskfile.
Added kmap_atomic/kunmap_atomic. Added protection of KM_IRQ0 slot with
local_irq_save(), local_irq_restore(), and comments.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return FAILED from eh_ routines if command(s) is(are) not completed
There were scenarios where we may have returned from the error
handlers prior to all affected commands being flushed to the midlayer.
Add changes to ensure this doesn't happen.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adjust lpfc_scsi_buf allocation to account for lun_queue_depth and
error handling
Under high load and high duress, the error handler could steal some
command resources from the normal i/o path. Rework to allocate
additional resources to avoid this scneario.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace lpfc_sli_issue_iocb_wait_high_priority with lpfc_sli_issue_iocb_wait.
Simplify code paths, as there really wasn't a "priority"
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: James Smart <James.Smart@emulex.com>
There were scenarios where the error handlers could reuse an iotag
value of an active io. Remove all possibility of this by
pre-assigning iotag resources to command resources.
Signed-off-by: James Smart <James.Smart@emulex.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Table was not providing a lot of value and injected a couple of
errors. Removed it and made functionality inline.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix for "Unknown IOCB command Data: x0 x3 x0 x0" messages and
inability to see devices
On some platforms, the host-memory based ring mgmt area was not
zero. Also, driver wasn't manipulating the entire 32bits of the ring
pointers.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Reuse macros defined for sysfs store callbacks in the initialization
code in order to enforce the same range checking.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update adapter names to match Emulex naming conventions.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanup white spaces in argument calls & initializations, prune if
statements, remove casting and remove redundant if checks.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hopefully there should be a brand new replacement driver for this heap
of junk by the beginning of next year.
Acked By: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wrap a highly common idiom. Makes the code easier to read, helps pave
the way for sdev->{id,channel} removal, and adds a token that can easily
by grepped-for in the future.
There are a couple sdev_id() and scmd_printk() updates thrown in as well.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a flag to mark a PHY as attached to the HBA as opposed to beeing on
an expander. This is needed because various features are only supported
on those. This is a crude hack, the proper fix would be to use
different classes for host-attached vs expander phys. I'm looking into
that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes an issue reported in drivers/scsi/sr.c by Coverity
Error reported: Pointer returned from "scsi_cd" is never used
Patch description:
Remove the scsi_cd() call as it does not have any effect.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch attempts to fix an issue found in drivers/scsi/scsi_ioctl.c by Coverity.
Error reported:
CID: 3437
Checker: FORWARD_NULL (help)
File: /export2/p4-coverity/mc2/linux26/drivers/scsi/scsi_ioctl.c
Function: scsi_ioctl_send_command
Description: Variable "buf" tracked as NULL was passed to a function that dereferences it.
Patch description:
buf can be NULL if inlen and outlen are both 0. This patch adds check if the
length is non-zero before calling copy from/to user.
Signed-off-by: Jayachandran C. <c.jayachandran@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert megaraid to use pci_driver's shutdown method rather than
the generic device_driver shutdown method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IPR scsi adapter have an exposure today in that they issue BIST to the adapter
to reset the card. If, during the time it takes to complete BIST, userspace
attempts to access PCI config space, the host bus bridge will master abort the
access since the ipr adapter does not respond on the PCI bus for a brief
period of time when running BIST. On PPC64 hardware, this master abort
results in the host PCI bridge isolating that PCI device from the rest of the
system, making the device unusable until Linux is rebooted. This patch makes
use of some newly added PCI layer APIs that allow for protection from
userspace accessing config space of a device in scenarios such as this.
Signed-off-by: Brian King <brking@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/scsi/ipr.c | 2 ++
1 file changed, 2 insertions(+)
I'm using this card in a RAID1 with 2 new SATA drives with no problems.
Card - SATA 300 TX2plus PDC40775 (3d73)
Signed-off-by: Ed Kear <ed@kear.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- move default mode pages to the front of libata-scsi.c
so various functions can access them
- partial annotation of these pages, point out divergence
from sat-r06
- replace various mode page magic numbers with defines
- strengthen MODE SENSE command decoding: handle DBD
bit in cdb, yield block descriptor (per sat-r06) and
handle mode sub pages
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For now supporting the ->get_linkerrors method is mandatory. I'll
probably be beaten to implement the .show_foo variables and different
types of attributes soon..
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move the remaining bits of sgiwd93.h into sgiwd93.c; replace the use of
CMD_PER_LUN and CAN_QUEUE by raw numbers.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use physical addresses at the interface level, letting drivers remap
them as appropriate.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maciej W. Rozycki <macro@linux-mips.org>
Date: Mon Jun 13 19:55:42 2005 +0000
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: 'Andrew Vasquez' <andrew.vasquez@qlogic.com>
Drop scsi_populate_tag_msg() interrogation.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The file is missing an include of scsi_transport_fc.h
drivers/scsi/qla2xxx/qla_rscn.c:334: error: implicit declaration of function 'fc_remote_port_unblock'
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables. As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here's a patch which drops the eh_active checks in the qla2xxx
eh_handler callbacks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The previous patch adding the ability to nest struct class_device
changed the paramaters to the call class_device_create(). This patch
fixes up all in-kernel users of the function.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: pass interface to class intreface methods
Pass interface as argument to add() and remove() class interface
methods. This way a subsystem can implement generic add/remove
handlers and then call interface-specific ones.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While populating command type 6 and 7 IOCBs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ISP23xx and ISP24xx chips have support for an adaptive
method of posting SCSI command completions for multiple SCSI
commands during a single system interrupt.
SCSI commands are placed on the system response queue
without interrupting the host until 1) a delay timer
expires; or 2) a SCSI command completes with an error.
As long as the host software (qla2xxx) services the response
queue for completions (this polling is done during
queuecommand()) within the 'delay timer' period, the
firmware will not generate system interrupt.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The non-handled failure cases of the Fabric Login mailbox
command handling logic would incorrectly mark the fcport as
dead and not allow the standard port-down-retry-count logic
to manage the transition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch adds the 'new comm' interface, which modern AAC based
adapters that are less than a year old support in the name of much
improved performance. These modern adapters support both the legacy and
the 'new comm' interfaces.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch resolves a compiler warning on 64 bit architectures.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
The compat field needed to be in cpu order.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
This patch uses the adapter supplemental information AdapterTypeText as
the default for the array name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Mark Haverkamp <markh@osdl.org>
Received from Mark Salyzyn.
This patch changes the driver over to utilizing the DMA_64BIT_MASK and
DMA_32BIT_MASK manifests.
Applies to the scsi-rc-fixes-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Rejects fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace the mcr53c8xx roll your own ktime_... macros with the correct
time_after() et al.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one()'s call to qla2x00_iospace_config() fails, we call
qla2x00_free_device() to clean up. But because ha->dpc_pid hasn't been set
yet, qla2x00_free_device() tries to stop a kernel thread which hasn't started
yet. It does wait_for_completion() against an uninitialised completion struct
and the kernel hangs up.
Fix it by initialising ha->dpc_pid a bit earlier.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct some function names in kernel-doc.
Add some kernel-doc descriptions.
Fix some typos.
Remove a few blank lines.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Just set the name field directly in the device_driver structure
contained in the vio_driver struct.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sata_qstor strays into a nasty area - gcc handling of wide enums is
full of bugs that got fixed between gcc versions creating portability
nightmare. Single-member enums are safe, so are ones that stay within
the range of int or unsigned int. Anything beyond that is asking for
trouble.
Declaration of constants split in two enums, taking the ~0UL one into
a separate enum.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Jeff found an endian bug in the Marvell driver (thanks!). Here's the
fix for it.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Found in the -rt patch set. The scsi_error thread likely will be in the
TASK_INTERRUPTIBLE state upon exit. This patch fixes this bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Found in the -rt patch set. The scsi_error thread likely will be in the
TASK_INTERRUPTIBLE state upon exit. This patch fixes this bug.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
problem:
id[53-58] might be changed after initializing device CHS settings.
changes:
- call ata_dev_reread_id() to reread the identify device info,
after initializing device CHS settings.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This change makes quirk_intel_ide_combined() dependent on the precise
conditions under which it is needed:
* IDE is built in
* IDE SATA option is not set
* ata_piix or ahci drivers are enabled
This fixes an issue where some modular configurations would not cause
the quirk to be enabled.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus torvalds <torvalds@osdl.org>
The patch below should make the Pioneer DRM-624X automatically
be set up with all 6 "drives". (6 slot SCSI CD changer)
Signed-off-by: Karl Magnus Kolst <karl.kolsto@uib.no>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a request is deferred in scsi_init_io because the sg table could not
be allocated, the associated scsi_cmnd is not released and the request is
not marked with REQ_DONTPREP. When the command is retried, if
scsi_prep_fn decides to kill it then the scsi_cmnd will never be released.
This patch (as573) changes scsi_init_io so that it calls scsi_put_command
before deferring a request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Juan was kind enough to linger on site, and work on a production
machine, to try the parameter to make the system stable. He discovered
that reducing the maximum transfer size issued to the adapter to 128KB
stabilized his system. This is related to an earlier change for the
2.6.13 tree resulting from Martin Drab's testing where the transfer size
was reduced from 4G to 256KB; we needed to go still further in scaling
back the request size.
Here is the patch that tames this regression.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix 12 undefined preprocessor identifier warnings (4 each in 3 driver builds):
drivers/scsi/NCR5380.c:2744:16: warning: undefined preprocessor identifier 'NDEBUG_ABORT'
drivers/scsi/NCR5380.c:2744:16: warning: "NDEBUG_ABORT" is not defined
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While doing some testing of error cases I ran into this bug. In some cases
the reset handler can exit with the host_lock still held.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days, in 2.6.x, even INQUIRY commands are sent using
scatter gather lists.
Bug reported by Tom 'spot' Callaway.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for sil_3131 and sil_3531. Both are
identical to 3124 except that they have only one port. Bits 30 and 31
of ata_port_info->host_flags is used to encode available port numbers.
Version number is bumped to 0.22.
Edward Falk supplied all the necessary information and preliminary
patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
- change "xlat" and "fill" actors in libata-scsi so
they are responsible for SCSI status and sense data
when they return 1. This allows GOOD status or a
specialized error to be set.
- yield an error for mode sense requests for saved
values [sat-r06]
- remove static inlines for ata_bad_scsiop() and
ata_bad_cdb() which are no longer used
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add extern ata_scsi_set_sense() to build SCSI
fixed sense data and corresponding SCSI status
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hello, guys.
This patch implements ->tf_read callback for sil24. It didn't use to
be necessary but new ata_gen_fixed_sense now makes use of ->tf_read
callback. This patch is taken from Edward Falk's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
03_sil24_add-tf-reading.patch
This patch implements proper TF register reading back and
caching and bumps up version to 0.22. This is taken from
Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 50 +++++++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 45 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
01_sil24_ignore-non-error-exception-irqs.patch
Do not error-finish commands for non-error exception irqs -
just ignore them. This is taken from Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This should fix up lockups that people were seeing due to
improper spinlock placement. Also, the start/stop DMA routines put
guarded trust in the cached state of DMA.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
1) note urgent bug, that completes command twice
2) only fix up INQUIRY data if the SCSI version is zero (typically
indicates ATAPI MMC-ish device)
3) if there is a problem on the ATA bus, don't bother with REQUEST
SENSE, just directly handle the error based on Status/Error registers.
megaraid_sas depends on arch-specific indirect includes pulling
fs.h in; on alpha they do not.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
This is my libata compatible low level driver for the Marvell SATA
family. Currently it runs in DMA mode on a 6081 chip.
The 5xxx series parts are not yet DMA capable in this driver because
the registers have differences that haven't been accounted for yet.
Basically, I'm focused on the 6xxx series right now. I apologize for
those seeing problems on the 5xxx series, I've not had a chance to
look at those problems yet.
For those curious, the previous bug causing the SCSI timeout and
subsequent panics was caused by an improper clear of hc_irq_cause in
mv_host_intr().
This version is running well in my environment (6081 chips,
with/without SW raid1) and is showing equal or better performance
compared to the Marvell driver (mv_sata) in my initial tests (timed
dd's of reads/writes to/from memory/disk).
I still need to look at the causes of occasional problems such as this:
ata11: translating stat 0x35 err 0x00 to sense
ata11: status=0x35 { DeviceFault SeekComplete CorrectedError Error }
SCSI error : <10 0 0 0> return code = 0x8000002
Current sda: sense key Hardware Error
end_request: I/O error, dev sda, sector 3155010
and this, seen at init time:
ATA: abnormal status 0x80 on port 0xE093911C
but they aren't showstoppers.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since our max_lun is unconditionally set to 1, we might as well
hardcode a LUN 0 probe, rather than a wildcard LUN scan.
The ide-scsi driver sets max_lun to a value greater than under
certain conditions:
if ((drive->id->last_lun & 0x7) != 7)
host->max_lun = (drive->id->last_lun & 0x7) + 1;
else
host->max_lun = 1;
last_lun is Word 126 of IDENTIFY PACKET DEVICE, marked as obsolete
and undocumented in non-ancient specs. We'll leave it out for now.
Should the need arise to support multi-LUN ATAPI devices, we'll
probably want to add the above code.
Finally, there have been reports of REPORT LUNS commands locking up
ATAPI drives. Eliminating the wildcard LUN scan could help reduce
the trouble from problematic drives.
Replace SCSI's legacy "bang at the door" method of probing with one
directly controlled by the underlying ATA transport layer.
We now only call scsi_scan_target() for devices we find, rather than
probing every possible channel/id within a certain range.
Some Legacy megaraid cards can't actually cope with the scatter/gather
version of the READ CAPACITY command (which is what we now send them
since altering all SCSI internal I/O to go via the block layer). Fix
this (and a few other broken megaraid driver assumptions) by sending
the non-sg version of the command if the sg list only has a single
element.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In these drivers, scsi_remove_host() is called too late, at the point
it is called, the driver has already shut down too far to accept any
I/O that the shutdown might generate. Any generated I/O actually
triggers a panic.
Fix this by calling scsi_remove_host() as early as possible and not
calling scsi_host_put() until just before we kfree the ahc_softc.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem in our host release in that it calls
scsi_proc_hostdir_rm(). However, if you hold a reference to the host as
you remove the module, the host template (which proc uses) will be freed
and the system will panic when the host device is finally released.
Fix this by moving scsi_proc_hostdir_rm() to where it should be: in
scsi_remove_host().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A bunch of create_proc_dir_entry() calls creating directories had crept
in since the last sweep; converted to proc_mkdir().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Received from Mark Salyzyn from Adaptec.
High Priority Queues have *never* been used in the entire history of the
aac based adapters. Associated with this, aac_insert_entry can be
removed, SavedIrql can be removed & padding variable can be removed.
With the movement of SavedIrql out & replaced with an automatic variable
qflags, the locking can be refined somewhat. The sparse warnings did not
catch the need for byte swapping in the 'dprintk' debugging print
macros, so fixed this up when this code was moved outside of the now
refined locking.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
The size of the command packet's scatter gather list maximum size was
miscalculated in the low range leading to the driver initialization
limiting the maximum i/o size that could go to the Adapter. There were
no negative operational side effects resulting from this bad math, only
a subtle limit in performance of the Adapter at the top end of the
range.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
In the rare instances where the adapter, or the motherboard, is
misbehaving; driver initialization or shutdown becomes problematic. By
introducing a 3 minute timeout on the first interrupt driven command
during initialization, or the issuance of the adapter shutdown command
during driver unload, we can resolve the lockup problems induced by
common (but rare) hardware misbehaviors.
The timeout during initialization, should it occur, is accompanied by a
message presented to the console and the logs indicating that the user
should inspect and resolve problems with interrupt routing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds some additional error return checking and error return
value propagation during initialization. Also, the deprecation of
pci_module_init with pci_register_driver along with the change in return
values.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Hotplug sniffs the AIFs (events) from the adapter and if a container
change resulting in the device going offline (container zero), online
(container zero completed) or changing capacity (morph) it will take
actions by calling the appropriate API.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recevied from Mark Salyzyn from Adaptec.
Aif pre-allocation is used to pull the kmalloc outside of the locks.
Applies to the scsi-misc-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
There are a few adapters that are capable of creating devices with this large
of a capacity, but now that we have the large fib support in, the management
applications will be capable of generating them. The problem is, once they are
created, the driver will not be able to access the devices correctly without
this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brown paperbag bug: sas_rphy_delete was ordered completely
wrong. Fix it up to be the same order as sas_phy_delete or
fc_rport_terminate and fix rphy objects that leaked after module
removal.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a hole in the rport unblock handling when processing
fabric events via the ADISC/PLOGI device state machine. Original code
would not properly 'unblock' the port upon the port reloging into the
fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
