videodev converts old-style controls to an extended control so the ivtv and
cx18 drivers no longer have to handle both.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Randy Dunlap for reporting this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx18 can support transport streams with newer firmwares. Add a TS
capability to the generic cx2341x module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Completely rely on the video_ioctl2 debugging facilities rather than
doing it ourselves.
Fill in some missing fields in ivtv with VIDIOC_G_FBUF.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IVTV_IOC_DMA_FRAME ioctl fails to correctly 'start' the decoder. Although
yuv output will be correct, some functions which should be disabled while the
decoder is in use remain enabled. This can result in hardware registers being
corrupted, causing problems with the mpeg decoder. This patch ensures the
decoder 'start' sequence is called, disabling these functions until the
device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the yuv device may not always 'start' the decoder.
Although yuv output will be correct, some functions which should be disabled
while the decoder is in use remain enabled. This can result in hardware
registers being corrupted, causing problems with the mpeg decoder. This patch
simply moves the existing decoder 'start' sequence to earlier in the write()
handler.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the capture is scaled, then the video_temporal_filter is set to 0
by the cx2341x.c module since otherwise you would get ghosting.
However, this was also done in the VIDIOC_S_FMT ioctl which meant that
the video_temporal_filter control was reset to 0 or 8 each time S_FMT
was called. This was old code that should have been removed a long time
ago.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Based on an initial conversion patch from Douglas Landgraf.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Separate gpio_init field and xceive_pin and combine the two when
the gpio is initialized. So there is no longer any need to set the
xceive pin in the gpio_init values, simplifying the creation of a
new card definition.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Peter Brandt for doing the necessary tests to fill out the card
definition!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
snprinf() takes the trailing \0 into account in its length calculations,
so there is no need to subtract 1 to the buffer size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the ivtv framebuffer will now attempt to use DMA if the
amount of data to copy is >= 4096 bytes. This change effectively depreciates
the need for the proprietary IVTVFB_IOC_DMA_FRAME ioctl since a write() of
sufficient size will do the same thing.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Update all the remaining new-style i2c drivers to use standard module
aliasing instead of the old driver_name/type driver matching scheme.
Note that the tuner driver is a bit quirky at the moment, as it
overwrites i2c_client.name with arbitrary strings. We write "tuner"
back on remove, to make sure that driver cycling will work properly,
but there may still be troublesome corner cases.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upon error conditions in cx18/ivtv_probe(), the code at the 'err:' label
leaves a NULL entry in cx18/ivtv_cards[]. This can cause a NULL pointer
de-reference in cx18/ivtv_v4l2_open() which is fixed by this patch.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- don't show kernel backtrace when the allocation of the buffers fails: the
normal ivtv/cx18 messages are clear enough and the backtrace scares users.
- fix cleanup after the buffer allocation fails (caused kernel panic).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix compile warnings if MODULE is not defined.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since:
1) FW_LOADER is defined as:
config FW_LOADER
tristate "Userspace firmware loading support"
depends on HOTPLUG
2) several V4L/DVB driver just selects it;
3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.
So, All drivers that select FW_LOADER should also depend on HOTPLUG.
An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:
drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_TUNER is responsible for compilation of tuners.ko module. This were the
previous behaviour before the creation of MEDIA_TUNER.
Before this patch, tuner.ko were created even for drivers that don't need a
tuner (like webcam drivers).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When there is a lot of DMA traffic this timeout might sometimes be too low.
Increase it to be on the safe side.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Note that this card is only detected and not yet working.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/v4l2-common.c:719:16: warning: Using plain integer as NULL pointer
drivers/media/video/au0828/au0828-dvb.c:122:19: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1101:22: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1102:23: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-audio.c:78:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-video-v4l.c:84:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1264:9: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-context.c:197:28: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:126:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:133:32: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:145:31: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:177:55: warning: Using plain integer as NULL pointer
drivers/media/video/videobuf-core.c💯9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frank Bennett reported that ivtv was causing skype to crash. With help
from one of their developers he showed it was a kernel problem.
VIDIOCGCAP copies a name into a fixed length buffer - ivtv uses names
that are too long and does not truncate them so corrupts a few bytes of
the app data area.
Possibly the names also want trimming but for now this should fix the
corruption case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ change_compare_np @
expression E;
@@
(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)
@ include depends on change_compare_np @
@@
@ no_include depends on !include && change_compare_np @
@@
#include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added the last remaining out-of-tree kernel driver from the ivtv project.
The saa717x is used in several Japanese cards and a Russian card. The
driver is not complete in that only NTSC is supported and no PAL/SECAM.
Hopefully this will be added in the future.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Kyuma Ohta <whatisthis@jcom.home.ne.jp>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
flags used for spinlocks don't need to be initialized, except where the
compiler has no way to see, that the spin_unlock_irqrestore is only called
if the spin_lock_irqsave has been called before. Local variable
initialization doesn't have to be protected.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are two tuner types: those for M/N standards and those for all others.
However, M/N standards are not always 60 Hz (PAL-N/Nc are 50 Hz), so rename
the module option accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow options like pal=bgh, improve description of those options.
Add tunerhz option: 50=card has 50Hz tuner, 60=card has 60Hz tuner.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The q_io queue was never taken into account by the poll function. Thanks to
Andy Walls for finding this bug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The DMA timeout timer was started once for each set of DMA transfers,
but it should be started for each single DMA transfer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CROPCAP suggests that video capture supports cropping, but this is not the
case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The existing yuv code limits output to the display area occupied by the
framebuffer. This patch allows the yuv output to be 'detached' via
V4L2_FBUF_FLAG_OVERLAY.
By default, the yuv output window will be restricted to the framebuffer
dimensions and the output position is relative to the top left corner of the
framebuffer. This matches the behaviour of previous versions.
If V4L2_FBUF_FLAG_OVERLAY is cleared, the yuv output will no longer be linked
to the framebuffer. The maximum dimensions are either 720x576 or 720x480
depending on the current broadcast standard, with the output position
relative to the top left corner of the display. The framebuffer itself can be
resized, moved and panned without affecting the yuv output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the following needlessly global functions static:
- ivtv_yuv_next_free()
- ivtv_yuv_setup_frame()
- ivtv_yuv_udma_frame()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a dma transfer is attempted for either yuv or framebuffer output, a missing
sg_init_table() call causes a kernel BUG in scatterlist.h if CONFIG_DEBUG_SG
is set.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As the result of a previous change that delayed the loading of the firmware,
the driver can sometimes report a bogus error regarding the yuv output filter
table not being found in the firmware. This patch moves the filter table
check to ensure it's only done after the firmware has been loaded.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix "warning: Using plain integer as NULL pointer".
Convert 'x < y ? x : y' to use min() instead.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the AVerMedia EZMaker PCI Deluxe and update the ivtv cardlist.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the shadowing 'struct v4l2_chip_ident *chip', since it already exists
and makes the if-statement useless.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv-yuv code clean up & reformat. Includes minor changes to some debug lines.
Also fixes a bug found during the reformatting, which would cause the
incorrect amount of yuv data to be sent to the card if source cropping
coordinates were used.
Apart from the bug-fix, there should be no functional difference to the
previous version.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver was incorrectly reporting that it supported YUV 4:2:2 output, when
it is actually YUV 4:2:0. Though I believe the hardware can be pushed to
4:2:2, we don't currently support that.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously, all yuv data written to /dev/video48 had only basic support with
no double buffering to avoid display tearing.
With this patch, yuv frames written to video48 are now handled by the existing
IVTV_IOC_DMA_FRAME framework. As such, the frames are hardware buffered to
avoid tearing, and honour scaling mode & field order options. Unlike the
proprietary IVTV_IOC_DMA_FRAME ioctl, all parameters are controlled by the
V4L2 API.
Due to mpeg & yuv output restrictions being different, their V4L2 output
controls have been separated. To control the yuv output, the V4L2 calls must
be done via video48.
If the ivtvfb module is loaded, there will be one side effect to this merge.
The yuv output window will be constrained to the visible framebuffer area. In
the event that a virtual framebuffer size is being used, the limit to the
output size will be the virtual dimensions, but only the portion that falls
within the currently visible area of the framebuffer will be shown.
Like the IVTV_IOC_DMA_FRAME ioctl, the supplied frames must be padded to 720
pixels wide. However the height must only be padded up the nearest multiple
of 32. This would mean an image of 102 lines must be padded to 128. As long
as the true source image size is given, the padding will not be visible in
the final output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Interlace mode selection code moved into the frame setup phase, so it's now
run before the frame is loaded into a hardware buffer. Given that it can
affect how a new frame is displayed, it was a bit stupid running it after the
frame was already visible.
A few stray interlace related variables which were linked to individual frames
have now been moved into the yuv_frame_info struct. This means that all
variables linked to a specific frame are in the same place & not scattered.
Minor code reformatting in areas touched by the above changes.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To reduce the number of display register accesses, the yuv code keeps track of
the current video settings. Should there be a change in any single parameter,
it will update the associated display registers to ensure everything is
displayed correctly.
The existing check also looks at the field order for the video. This is not
required, since field reversal does not require any display register changes.
This patch removes the field order from the check.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Inadvertently missed a line when converting code to new hardware buffering
method. In some circumstances, this would lead to a frame being displayed
using parameters belonging to another frame.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv_yuv_prep_frame is split in smaller code blocks.
Modified yuv buffer handling on the PVR350 itself. We now cycle through all 8
hardware buffers.
With this patch in place, driver behaviour should remain unchanged from the
existing release.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the yuv output stream buffer is divided into blocks whose size
depend on the broadcast standard selected during the driver init phase.
However, the standard can be changed after the init phase. This effectively
breaks the yuv output stream handler, since it relies on the different yuv
planes being block aligned.
This patch changes the setup, so that the block size is always the same. The
decoder dma function has been modified to cope with the fact that the second
yuv plane may no longer be block aligned. The start of the yuv frame must
still be at the beginning of a block, so the stream write function has also
been modified to ensure this is always true.
Also, the stream write function will now initiate a yuv dma transfer as soon
as a full frame is ready. It will not wait until the current write request
has completed, or the stream buffer becomes full.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also replaces all occurrences of TUNER_XCEIVE_XC3028 to TUNER_XC2028.
Some work is still may be required to make sure that non-tm6000 drivers will
be capable of using tuner-xc2028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using an udelay of 5 seems to result in problems for several people.
For now abandon the udelay value of 5 and stick to 10, even though this
will mean a longer load time of the cx2584x firmware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The eeprom decides which Hauppauge model it is, so the decision whether to
use an udelay of 5 or 10 needs to be taken after reading the eeprom, not
before.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is referenced both from __devinit code (ivtv_probe) and
normal .text (ivtv_process_eeprom), and therefore cannot
be discarded via __devexit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commits
58b053e4ce ("Update arch/ to use sg helpers")
45711f1af6 ("[SG] Update drivers to use sg helpers")
fa05f1286b ("Update net/ to use sg helpers")
converted many files to use the scatter gather helpers without ensuring
that the necessary headerfile <linux/scatterlist> is included. This
happened to work for ia64, powerpc, sparc64 and x86 because they
happened to drag in that file via their <asm/dma-mapping.h>.
On most of the others this probably broke.
Instead of increasing the header file spider web I choose to include
<linux/scatterlist.h> directly into the affectes files.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (37 commits)
V4L/DVB (6382): saa7134: fix NULL dereference at suspend time for cards without IR receiver
V4L/DVB (6380): ivtvfb: Removal of the 'osd_compat' module option
V4L/DVB (6379): patch which improves GotView Saa7135 remote control
V4L/DVB (6378b): Updates info about the removal of V4L1 at feature-removal-schedule.txt
V4L/DVB (6378a): Removal of VIDIOC_[G|S]_MPEGCOMP from feature-removal-schedule.txt
V4L/DVB (6378): DiB0700-device: Using 1.10 firmware
V4L/DVB (6357): pvrusb2: Improve encoder chip health tracking
V4L/DVB (6356): "while (!ca->wakeup)" breaks the CAM initialisation
V4L/DVB (6352): ir-kbd-i2c: Missing break statement
V4L/DVB (6350): V4L: possible leak in em28xx_init_isoc
V4L/DVB (6348): ivtv: undo video mute when closing the radio
V4L/DVB (6347): ivtv: fix video mute when radio is used
V4L/DVB (6346): ivtvfb: YUV output size fix when ivtvfb is not loaded
V4L/DVB (6345): ivtvfb: YUV handling of an image which is not visible in the display area
V4L/DVB (6343): ivtvfb: check return value of unregister_framebuffer
V4L/DVB (6342): ivtv: fix circular locking (bug 9037)
V4L/DVB (6341): ivtv: fix resizing MPEG1 streams
V4L/DVB (6340): ivtvfb: screen mode change sometimes goes wrong
V4L/DVB (6339): ivtv: set the video color to black instead of green when capturing from the radio
V4L/DVB (6338): ivtv: fix incorrect EBUSY return
...
Due to changes in the core ivtv driver as of release 1.0, the osd_compat
module option has been rendered obsolete. This patch removes the option and
all code associated with it.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the radio is active the video should be muted when a capture
starts. However, this was done at the wrong time and the mute settings
were overwritten when cx2341x_update was called.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the ivtvfb module isn't loaded, the valid YUV output area should be set to
full-screen. This patch fixes the case where the valid output area was not
reset when the output broadcast format was changed from NTSC to PAL. This
resulted in output being limited to the top 480 lines of the display.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the ivtvfb module is loaded, the YUV output is relative to the
framebuffer output. When a virtual screen size is used, the output area for
the YUV may actually be off screen. To prevent the hardware from crashing,
the current driver will ignore an off-screen position and leave the output
visible at the last on-screen position. This may not be desirable, so this
patch will switch off the YUV output should the image move off-screen, and
re-enable it should the image move on-screen again.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
