There is a bug when VLAN is configured on the cxgb3 interface, the iscsi
conn. would be denied with message "cxgb3i: NOT going through cxgbi device."
This patch adds code to get the real egress net_device when vlan is configured.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling and wiring mode correction:
RGB wiring on the -EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use BLOCK_NIL consistently rather than sometimes 0xffff and sometimes
BLOCK_NIL.
The semantic patch that finds this issue is below
(http://www.emn.fr/x-info/coccinelle/). On the other hand, the changes
were made by hand, in part because drivers/mtd/inftlcore.c contains dead
code that causes spatch to ignore a relevant function. Specifically, the
function INFTL_findwriteunit contains a do-while loop, but always takes a
return that leaves the loop on the first iteration.
// <smpl>
@r exists@
identifier f,C;
@@
f(...) { ... return C; }
@s@
identifier r.C;
expression E;
@@
@@
identifier r.f,r.C,I;
expression s.E;
@@
f(...) {
<...
(
I
|
- E
+ C
)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In multi-run (-r/--repeat) printouts, print out the noise of
the wall-clock average as well.
Also, fix a bug in printing out scaled counters: if it was not
scaled then we should not update the average with -1.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allow a no-counters run. This can be useful to measure just
elapsed wall-clock time - or to assess the raw overhead of perf
stat itself, without running any counters.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vince Weaver reported that there's a handful of #ifdef __MINGW32__
sections in the code.
Remove them as they are in essence dead code - as unlike upstream
Git, the perf tool is unlikely to be ported to Windows.
Reported-by: Vince Weaver <vince@deater.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When NAPI is disabled while we're in net_rx_action, we end up
calling __napi_complete without flushing GRO packets. This is
a bug as it would cause the GRO packets to linger, of course it
also literally BUGs to catch error like this :)
This patch changes it to napi_complete, with the obligatory IRQ
reenabling. This should be safe because we've only just disabled
IRQs and it does not materially affect the test conditions in
between.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As transparent proxying looks up the socket early and assigns
it to the skb for later processing, we must drop any existing
socket ownership prior to that in order to distinguish between
the case where tproxy is active and where it is not.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
scripts/ihex2fw is a generated binary and should be ignored
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Some distributions have enabled the gcc flag -Wformat-security by default.
This results in a number of warnings about format arguments to functions,
sometimes in cases where fixing the warning is not likely to actually fix a
bug. Instead of hand patching a dozens of places (possibly more) that produce
warnings that get ignored anyway we just turn off the flag in the Makefile.
Signed-off-by: Floris Kraak <randakar@gmail.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
In the series for 2.6.31 it was noticed to ship the copyright,
but the generated changelog got lost somehow.
As bonus the generated linux-image deb packages are Lenny lintian clean.
Cc: Frans Pop <elendil@planet.nl>
Cc: Andres Salomon <dilinger@debian.org>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch is preparation for replacing most ".data.init_task" in the
kernel with macros, so that the section name can later be changed
without having to touch a lot of the kernel.
The long-term goal here is to be able to change the kernel's magic
section names to those that are compatible with -ffunction-sections
-fdata-sections. This requires renaming all magic sections with names
of the form ".data.foo".
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
We recently added a INIT_TASK(align) in include/asm-generic/vmlinux.lds.h,
but there is already a macro INIT_TASK in include/linux/init_task.h, which
is quite confusing. We should switch the macro in the linker script to
INIT_TASK_DATA. (Sorry that I missed this in reviewing the patch). Since
the macros are new, there is only one user of the INIT_TASK in
vmlinux.lds.h, arch/mn10300/kernel/vmlinux.lds.S.
However, we are currently using INIT_TASK_DATA for laying down an entire
.data.init_task section. So rename that to INIT_TASK_DATA_SECTION.
I would be worried about changing the meaning of INIT_TASK_DATA, but the
old INIT_TASK_DATA implementation had no users, and in fact if anyone had
tried to use it, it would have failed to compile because it didn't pass
the alignment to the old INIT_TASK.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch is preparation for replacing most uses of
".bss.page_aligned" and ".data.page_aligned" in the kernel with
macros, so that the section name can later be changed without having
to touch a lot of the kernel.
The long-term goal here is to be able to change the kernel's magic
section names to those that are compatible with -ffunction-sections
-fdata-sections. This requires renaming all magic sections with names
of the form ".data.foo".
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
RW_DATA_SECTION is defined to take 4 different alignment parameters,
while NOSAVE_DATA currently uses a fixed PAGE_SIZE alignment as noted
in the comments.
There are presently no in-tree users of this at present, and I just
stumbled across this while implementing the simplified script on a new
architecture port, which subsequently resulted in a syntax error.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The mac80211 module uses rcu_call() thus it should use rcu_barrier()
on module unload.
The rcu_barrier() is placed in mech.c ieee80211_stop_mesh() which is
invoked from ieee80211_stop() in case vif.type == NL80211_IFTYPE_MESH_POINT.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunrpc module uses rcu_call() thus it should use rcu_barrier() on
module unload.
Have not verified that the possibility for new call_rcu() callbacks
has been disabled. As a hint for checking, the functions calling
call_rcu() (unx_destroy_cred and generic_destroy_cred) are
registered as crdestroy function pointer in struct rpc_credops.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading modules that uses call_rcu() callbacks, then we must
use rcu_barrier(). This module uses syncronize_net() which is not
enough to be sure that all callback has been completed.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 module uses rcu_call() thus it should use rcu_barrier() on
module unload.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decnet module unloading as been disabled with a '#if 0' statement,
because it have had issues.
We add a rcu_barrier() anyhow for correctness.
The maintainer (Chrissie Caulfield) will look into the unload issue
when time permits.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Chrissie Caulfield <christine.caulfield@googlemail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some devices in the wild that clear the DRQ bit during the
last word of a packet command and therefore could use a "second chance"
for that last word of data to be xferred instead of simply failing the
request. Do that by attempting to suck in those last bytes in PIO mode.
In addition, the ATA_ERR bit has to be cleared for we cannot be sure the
data is valid otherwise.
See http://bugzilla.kernel.org/show_bug.cgi?id=13399 for details.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The m25p16 data sheet from numonyx lists the worst-case bulk erase time
(tBE) as 40 seconds.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: misc small cleanups
amd64_edac: fix ecc_enable_override handling
amd64_edac: check only ECC bit in amd64_determine_edac_cap
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (29 commits)
powerpc/rtas: Fix watchdog driver temperature read functionality
powerpc/mm: Fix potential access to freed pages when using hugetlbfs
powerpc/440: Fix warning early debug code
powerpc/of: Fix usage of dev_set_name() in of_device_alloc()
powerpc/pasemi: Use raw spinlock in SMP TB sync
powerpc: Use one common impl. of RTAS timebase sync and use raw spinlock
powerpc/rtas: Turn rtas lock into a raw spinlock
powerpc: Add irqtrace support for 32-bit powerpc
powerpc/BSR: Fix BSR to allow mmap of small BSR on 64k kernel
powerpc/BSR: add 4096 byte BSR size
powerpc: Map more memory early on 601 processors
powerpc/pmac: Fix DMA ops for MacIO devices
powerpc/mm: Make k(un)map_atomic out of line
powerpc: Fix mpic alloc warning
powerpc: Fix output from show_regs
powerpc/pmac: Fix issues with PowerMac "PowerSurge" SMP
powerpc/amigaone: Limit ISA I/O range to 4k in the device tree
powerpc/warp: Platform fix for i2c change
powerpc: Have git ignore generated files from dtc compile
powerpc/mpic: Fix mapping of "DCR" based MPIC variants
...
Newly allocated objects are more likely to be reported as false
positives. Kmemleak ignores the reporting of objects younger than 5
seconds. However, this age was calculated after the memory scanning
completed which usually takes longer than 5 seconds. This patch
make the minimum object age calculation in relation to the start of the
memory scanning.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since there is a kernel thread for automatically scanning the memory, it
makes sense for the debug/kmemleak file to only show its findings. This
patch also adds support for "echo scan > debug/kmemleak" to trigger an
intermediate memory scan and eliminates the kmemleak_mutex (scan_mutex
covers all the cases now).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Because of false positives, the memory scanning thread may print too
much information. This patch changes the scanning thread to only print
the number of newly suspected leaks. Further information can be read
from the /sys/kernel/debug/kmemleak file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: video: prevent NULL deref in acpi_get_pci_dev()
eeepc-laptop: add rfkill support for the 3G modem in Eee PC 901 Go
eeepc-laptop: get the right value for CMSG
eeepc-laptop: makes get_acpi() returns -ENODEV
eeepc-laptop: right parent device
eeepc-laptop: rfkill refactoring
eeepc-laptop.c: use pr_fmt and pr_<level>
eeepc-laptop: Register as a pci-hotplug device
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] remove unknown mount option warning message
[CIFS] remove bkl usage from umount begin
cifs: Fix incorrect return code being printed in cFYI messages
[CIFS] cleanup asn handling for ntlmssp
[CIFS] Copy struct *after* setting the port, instead of before.
cifs: remove rw/ro options
cifs: fix problems with earlier patches
cifs: have cifs parse scope_id out of IPv6 addresses and use it
[CIFS] Do not send tree disconnect if session is already disconnected
[CIFS] Fix build break
cifs: display scopeid in /proc/mounts
cifs: add new routine for converting AF_INET and AF_INET6 addrs
cifs: have cifs_show_options show forceuid/forcegid options
cifs: remove unneeded NULL checks from cifs_show_options
sky2 driver on PowerPC targets floods kernel log with following errors:
eth1: hw csum failure.
Call Trace:
[ef84b8a0] [c00075e4] show_stack+0x50/0x160 (unreliable)
[ef84b8d0] [c02fa178] netdev_rx_csum_fault+0x3c/0x5c
[ef84b8f0] [c02f6920] __skb_checksum_complete_head+0x7c/0x84
[ef84b900] [c02f693c] __skb_checksum_complete+0x14/0x24
[ef84b910] [c0337e08] tcp_v4_rcv+0x4c8/0x6f8
[ef84b940] [c031a9c8] ip_local_deliver+0x98/0x210
[ef84b960] [c031a788] ip_rcv+0x38c/0x534
[ef84b990] [c0300338] netif_receive_skb+0x260/0x36c
[ef84b9c0] [c025de00] sky2_poll+0x5dc/0xcf8
[ef84ba20] [c02fb7fc] net_rx_action+0xc0/0x144
The NIC is Yukon-2 EC chip revision 1.
Converting checksum field from le16 to CPU byte order fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Complete the counter swap by indeed switching the times too and
updating the userpage after modifying the counter values.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1246014623.31755.195.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the newly created callchains radix tree to gather the chains stats
from the recorded events and then print the callchains for all of them,
sorted by hits, using the "-c" parameter with perf report.
Example:
66.15% [k] atm_clip_exit
63.08%
0xffffffffffffff80
0xffffffff810196a8
0xffffffff810c14c8
0xffffffff8101a79c
0xffffffff810194f3
0xffffffff8106ab7f
0xffffffff8106abe5
0xffffffff8106acde
0xffffffff8100d94b
0xffffffff8153e7ea
[...]
1.54%
0xffffffffffffff80
0xffffffff810196a8
0xffffffff810c14c8
0xffffffff8101a79c
[...]
Symbols are not yet resolved.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1246026481-8314-3-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We plan to display the callchains depending on some user-configurable
parameters.
To gather the callchains stats from the recorded stream in a fast way,
this patch introduces an ad hoc radix tree adapted for callchains and also
a rbtree to sort these callchains once we have gathered every events
from the stream.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1246026481-8314-2-git-send-email-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
amd64_check_ecc_enabled() returns non-zero status when ECC
checking/correcting is disabled and this fails further loading of the
driver even when 'ecc_enable_override' boot param is used.
Fix that by clearing return status in that case.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Checking whether the machine is using ECC enabled DRAM is done through
testing the DimmEccEn bit in the DRAM Cfg Low register (F2x[1,0]90). Do
that instead of testing all bits from the DimmEccEn upwards.
Also, remove mci->edac_cap assignment and use value returned from
amd64_determine_edac_cap().
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Drop the e820 scanning and use existing function for finding valid
RAM regions to add to 1:1 mapping.
Signed-off-by: Chris Wright <chrisw@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first entry of the ftrace profile was always skipped when
reading trace_stat/functionX.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4A443D59.4080307@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_kill_rq()
and ide_floppy_do_request() for failed requests.
[ bugfix part ]
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_do_devset()
and ide_complete_drive_reset(). Then remove ide_rq_bytes().
[ cleanup part ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such requests should be failed with -EIO (like all other requests
in this function) instead of being completed successfully.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTAS watchdog driver to read out the temperature crashes
on a PXCAB:
Unable to handle kernel paging request for data at address 0xfe347b50
Faulting instruction address: 0xc00000000001af64
Oops: Kernel access of bad area, sig: 11 [#1]
The wrong usage of "(void *)__pa(&temperature)" in rtas_call() is
removed by using the function rtas_get_sensor() which does the
right thing.
Signed-off-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using 64k page sizes, our PTE pages are split in two halves,
the second half containing the "extension" used to keep track of
individual 4k pages when not using HW 64k pages.
However, our page tables used for hugetlb have a slightly different
format and don't carry that "second half".
Our code that batched PTEs to be invalidated unconditionally reads
the "second half" (to put it into the batch), which means that when
called to invalidate hugetlb PTEs, it will access unrelated memory.
It breaks when CONFIG_DEBUG_PAGEALLOC is enabled.
This fixes it by only accessing the second half when the _PAGE_COMBO
bit is set in the first half, which indicates that we are dealing with
a "combo" page which represents 16x4k subpages. Anything else shouldn't
have this bit set and thus not require loading from the second half.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
