NVidia reports (via Mark Overby) that some of their EHCI controllers
don't like certain data structure addresses beyond the 2GB mark.
He provided an earlier version of this patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One change may improve some S1 or S3 resume cases, and the other
seems mostly to explain some strange state "lsusb" would show.
Two fixes:
- On resume, don't think about resuming any unpowered port, or
resetting any port with OWNER set to the OHCI/UHCI companion.
This will make some S1 and S3 resume scenarios work better.
- PORT_CSC was not being cleared correctly in ehci_hub_status_data.
This was visible at least through current versions of "lsusb",
and might have caused some other hub related strangeness.
The fix addresses all three write-to-clear bits, using the same
approach that UHCI happens to use: a mask of bits that are
cleared in most writes to that port status register.
Original patch seems to have been from from William.Morrow@amd.com
and this version (from David) finishes the write-to-clear changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Three new device IDs for CP2101 USB to UART Bridge
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as558) removes from the UHCI driver a kernel timer used for
checking Full Speed Bandwidth Reclamation (FSBR). The checking can be
done during normal root-hub polling; it doesn't need a separate timer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as549) introduces two small changes in the HCD glue layer.
The first simply removes a redundant test. The second allows root-hub
polling to continue for a single iteration after a host controller dies;
this is needed for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the USB touchpad which can be found on post-February 2005
Apple PowerBooks.
This driver is derived from Johannes Berg's appletrackpad driver [1],
but it has been improved in some areas:
* appletouch is a full kernel driver, no userspace program is necessary
* appletouch can be interfaced with the synaptics X11 driver[2], in order
to have touchpad acceleration, scrolling, two/three finger tap, etc.
This driver has been tested by the readers of the 'debian-powerpc' mailing
list for a few weeks now and I believe it is now ready for inclusion into the
mainline kernel.
Credits go to Johannes Berg for reverse-engineering the touchpad protocol,
Frank Arnold for further improvements, and Alex Harper for some additional
information about the inner workings of the touchpad sensors.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
here is a new and extended version of the sisusbvga (previously: sisusb)
driver. The patch is against 2.6.13 and updates the driver to version 0.0.8.
Additions include complete VGA/EGA text console support and a build-in
display mode infrastructure for userland applications that don't know
about the graphics internals.
Fixes include some BE/LE issues and a get/put_dev bug in the previous
version.
Other changes include a change of the module name from "sisusb" to
"sisusbvga". The previous one was too generic IMHO.
Please note that the patch also affects the Makefile in
drivers/video/console as the driver requires the VGA 8x16 font in case
the text console part is selected.
Heavily tested, as usual. Please apply.
One thing though: I already prepared for removal of the "mode" field and
the changed "name" field in the usb_class_driver structure. This will
perhaps need some refinement depending on whether you/Linus merge the
respective core changes before or after 2.6.14.
Signed-off-by: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does a full cleanup of 'NULL checks before vfree', and a partial
cleanup of calls to kfree for all of drivers/ - the kfree bit is partial in
that I only did the files that also had vfree calls in them. The patch
also gets rid of some redundant (void *) casts of pointers being passed to
[vk]free, and a some tiny whitespace corrections also crept in.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up timer initialization by introducing DEFINE_TIMER a'la
DEFINE_SPINLOCK. Build and boot-tested on x86. A similar patch has been
been in the -RT tree for some time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch aggregates all modifications in the -mm tree and adds
complete ringtone support.
The following features are supported:
- keyboard full support
- LCD full support
- LED full support
- dialtone full support
- ringtone full support
- audio playback via generic usb audio diver
- audio record via generic usb audio diver
For driver documentation see: Documentation/input/yealink.txt
For vendor documentation see: http://yealink.com
Signed-off-by: Henk <Henk.Vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As sugested by Alan Stern here are a few code cleanups for onetouch.c:
-Check number of endpoints before directly referencing intf->endpoint[2]
-Use defined constants instead of magic numbers
-Revmove the non-ascii characters from copyright notice
-Make registration and deregistration messages more similar
Signed-off-by: Nick Sillik <n.sillik@temple.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This code looks at urb->transfer_dma, maps the page and takes the data.
I am looking for volunteers to contribute architectures other than i386
or to develop an architecure-neutral API for it (or point me that it
was done already).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the field tt_usecs to ehci_qh and ehci_iso_stream, and sets it
appropriately when setting them up as periodic endpoints. It records
the transation translator's think_time (added in last patch) plus the
downstream (i.e. low or full speed) bustime of the transfer associated
with each interrupt or iso frame, as calculated by usb_calc_bus_time.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds think_time to the usb_tt struct and sets it appropriately
(measured in ns); this can help us implement better split transaction
scheduling.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This wraps up the conversion of the "usbnet" driver structure, by
moving the Prolific PL-2201/2302 minidriver to a module of its own.
It also includes some minor cleanups to the remaining "usbnet" file,
notably removing that long changelog at the top.
Minor historical note: Linux 2.2 first called the driver for
this hardware "plusb".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds host-side RNDIS support to the "usbnet" driver, so Linux can talk
to various devices (often based on WinCE) that otherwise only Windows could
talk to.
Tested with little-endian Linux talking to a Linux-USB Ethernet/RNDIS based
peripheral. This also includes updates from Eddie C. Dost <ecd@brainaid.de>
for big-endian SPARC Linux talking to a Nokia 9500 Communicator.
It's still marked as EXPERIMENTAL because this code is so young. This
ought to let Linux to work with various cable modems that previously
would have been "Windows Only".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes the CDC Ethernet support live in a separate driver module.
This module is a bit special since it exports utility functions
that are reused by the the Zaurus and RNDIS drivers, but it's
not "core" like usbnet itself.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves usbnet support for Zaurus and compatibles into its own module.
Other than exporting a couple of helper functions, this just involved
shuffling some code and updating the comments.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the GeneSys GL620USB-A support into its own driver file.
It also fixes a "return wrong skb" glitch in the rx unbatching, as
recently reported, and adds some missing byteswaps in the special
"genelink" headers (so it might now work on big-endian Linux).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As with the "cdc_subset" and "asix" drivers, this just moves the net1080
support into its one driver module. In this case there's a small bit of
extra cleanup involved, moving some funky framing logic into the tx_fixup()
routine (resolving a long overdue FIXME).
Minor historical note: "usbnet" started out as "net1080", then got
generalized to make it easier for other network drivers to reuse the
urb queueing and fault management code here.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the ASIX AX8817x driver into its own file, just using
the "usbnet" infrastructure as a utility library.
- As with "cdc_subset" this involved minor Kconfig/kbuild tweaks,
moving code from one file to another, and exporting a few functions.
- This includes updates from Jamie Painter to add (and use) a new hook
to handle the different maximum transfer sizes for rx and tx sides.
- Also from Jamie, some bugfixes:
* MDIO byteorder (to address some PPC media negotiation problems);
* Force alignment at key spots when using ax88772 framing (on some
embedded hardware, the network stack will break otherwise);
* Address some link reset problems.
It also makes this driver use the standard (5 seconds vs half second)
control timeouts used elsewhere in USB; and wraps a few lines before
the 80th column (which previously needed it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch creates the first of several separate "minidriver" modules
for "usbnet". This one handles only the very simplest hardware, which
can be handled almost entirely by the "usbnet" core.
- Move device-specific bits into new "cdc_subset.c" driver,
shrinking "usbnet" by a bunch;
- Export the functions needed to support this minidriver
(with EXPORT_SYMBOL_GPL);
- Update Kconfig and kbuild accordingly.
This one handles about a dozen different device types, with the most
notable ones being Gumstix and most Linux-based PDAs (except Zaurus
running that ancient code from Sharp).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This starts to prepare the core of "usbnet" to know less about various
framing protocols that map Ethernet packets onto USB, so "minidrivers"
can be modules that just plug into the core.
- Remove some framing-specific code that cluttered the core:
* net->hard_header_len records how much space to preallocate;
now drivers that add their own framing (Net1080, GeneLink,
Zaurus, and RNDIS) will have smoother TX paths. Even for
the drivers (Zaurus, Net1080) that need trailers.
* defines new dev->hard_mtu, using this "hardware" limit to
check changes to the link's settable "software" mtu.
* now net->hard_header_len and dev->hard_mtu are set up in the
driver bind() routines, if needed.
- Transaction ID is no longer specific to the Net1080 framing;
RNDIS needs one too.
- Creates a new "usbnet.h" header with declarations that are shared
between the core and what will be separate modules.
- Plus a couple other minor tweaks, like recognizing -ESHUTDOWN
means the keventd work should just shut itself down asap.
The core code is only about 1/3 of this large file. Splitting out the
minidrivers into separate modules (e.g. ones for ASIX adapters,
Zaurii and similar, CDC Ethernet, etc), in later patches, will
improve maintainability and shrink typical runtime footprints.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix
drivers/usb/misc/ldusb.c: In function `ld_usb_read':
drivers/usb/misc/ldusb.c:467: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c: In function `ld_usb_write':
drivers/usb/misc/ldusb.c:531: warning: int format, different type arg (arg 4)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 5)
drivers/usb/misc/ldusb.c:532: warning: int format, different type arg (arg 6)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Deprecate the OSS USB drivers.
This patch includes spelling fixes by Lee Revell.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ohci-ppc-soc.c provides for a platform-specific callback mechanism for
when the HC is successfully probed or removed. It turned out that none
of the 3 platforms using it need this facility. Also the required
include/asm-ppc/usb.h has never been accepted. This patch removes the
callback feature and the include of <asm/usb.h>.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid an annoying message that can appear if devices are disconnected
in the middle of a USB scatterlist operation.
Message noted in http://bugzilla.kernel.org/show_bug.cgi?id=4373
(but the real issue there seems to be a SCSI level hang).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use a more correct calculation for highspeed bit times.
http://bugzilla.kernel.org/show_bug.cgi?id=3604
This sort if thing might start to make a difference now that the high
speed periodic scheduler is more complete -- and even getting used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as556) adds support for unbinding the usb_generic "driver".
That driver only binds to USB devices, as opposed to interfaces, and it
does nothing much besides marking which struct device's go with an
overall USB device plus providing suspend/resume methods. Now that
users can unbind drivers at will using the sysfs "unbind" attribute, we
need a rational way of dealing with USB devices that are no longer under
full control of the USB stack. The patch handles this by unconfiguring
the device, thereby removing all the interfaces and their associated
drivers and children.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as555) modifies the already-awkward
usb_lock_device_for_reset routine in usbcore by adding a timeout. The
whole point of the routine is that the caller wants to acquire some
semaphores in the wrong order; protecting against the possibility of
deadlock by timing out seems only prudent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the port numbering confusion for the S3C24XX platform device
information as reported by Rudy <rudyboy168@gmail.com>
This patch ensurs that the the ports are numbered 0 and 1.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as554) makes the hub driver disconnect any child USB devices
when it is unbound from a hub. Normally this will never happen, but
there are a few oddball ways to unbind the hub driver while leaving the
children intact. For example, the new "unbind" sysfs attribute can be
used for this purpose.
Given that unbinding hubs with children is now safe, the patch also
removes the code that prevented people from doing so using usbfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as553) merely moves some code and deletes an unneeded test in
the hub driver. This is in preparation for the patch that follows.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding flash-device support to the shuttle_usbat driver in 2.6.11
introduced the need to detect which type of device we are dealing with:
CDRW drive, or flash media reader.
The detection routine used turned out to not work for HP8200 CDRW users,
who saw their devices being detected as a flash disk.
This patch (which has been tested on both flash and cdrom) removes some
unnecessary code, moves device detection to much later during
initialization, and introduces a new detection routine which appears to
work.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
29 July 2005, Cambridge, MA:
This afternoon Alan Stern submitted a patch to remove the URB_ASYNC_UNLINK
flag from the Linux kernel. Mr. Stern explained, "This flag is a relic
from an earlier, less-well-designed system. For over a year it hasn't
been used for anything other than printing warning messages."
An anonymous spokesman for the Linux kernel development community
commented, "This is exactly the sort of thing we see happening all the
time. As the kernel evolves, support for old techniques and old code can
be jettisoned and replaced by newer, better approaches. Proprietary
operating systems do not have the freedom or flexibility to change so
quickly."
Mr. Stern, a staff member at Harvard University's Rowland Institute who
works on Linux only as a hobby, noted that the patch (labelled as548) did
not update two files, keyspan.c and option.c, in the USB drivers' "serial"
subdirectory. "Those files need more extensive changes," he remarked.
"They examine the status field of several URBs at times when they're not
supposed to. That will need to be fixed before the URB_ASYNC_UNLINK flag
is removed."
Greg Kroah-Hartman, the kernel maintainer responsible for overseeing all
of Linux's USB drivers, did not respond to our inquiries or return our
calls. His only comment was "Applied, thanks."
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as479b, and has been rediffed. Please note
the order of submission of this latest patch series -- even tho this has
an older original number, it is the last patch I'll be sending today.
This patch changes the reported SCSI revision level to 2 for all
disk-type devices. This is needed in a few cases because the device
reports a level of 3 or higher but then crashes when given a REPORT LUNS
command (for which support is supposed to be mandatory at those levels).
This shouldn't harm us, since it only matters for sparse LUNs and we
have separate ways of coping with that.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is originally from Nick Sillik, and has been rediffed against
the latest tree.
This patch adds usability to the OneTouch Button on Maxtor External USB
Hard Drives. Using an unusual device entry it declares an extra init
function which claims the interrupt endpoint associated with this
button. The button is connected to the input system.
Signed-off-by: Nick Sillik <n.sillik@temple.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as534, and has been re-diffed against the latest
tree.
usb-storage has a small loophole, a window between the time queuecommand
accepts a new command and the time the control thread starts to execute
it. If disconnect is called during that window, the driver won't cancel
the pending command -- we've been relying on the SCSI core to cancel it
for us during host removal. But it's better for usb-storage to cancel
it; this avoids races and reduces reliance on the SCSI core.
Fortunately cancelling these commands is easy to do; the key is to do it
_before_ calling scsi_remove_host.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as533, and has been re-diffed against the
current tree.
Disconnect processing in usb-storage naturally divides into two parts:
one to quiesce the driver (make sure no commands are executing or
queued) and remove the host, and the other to deallocate all the USB and
non-USB resources. This patch creates two subroutines to handle those
two parts. Mostly it's just code movement, but there is one significant
change. If the scsi-scanning thread fails to initialize but the host
has successfully been added, we need to quiesce the driver before
removing the host. After all, it's possible that scanning could have
been initiated from somewhere else, such as userspace -- very low
probability, but it's easily handled by calling the new subroutine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as531 from Alan Stern. It has been rediffed
against the latest tree.
The SCSI people have deprecated the use of scsi_cmnd.serial_number for
anything other than printk. Worse than that, the SCSI core doesn't
always increment the number (when the error handler is running, for
example). So this patch creates a locally-stored value for use in
bulk-only tags. The net result is a simplification, since we no longer
have to save & restore the serial_number value while autosensing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch isp116x-hcd over from root hub polling to interrupt. This change closes
also a race that was present with the old polling scheme: status polling could
happen in a time window, where root hub status bits were not stable.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes support for user-provided platform-specific hardware reset
and clock starting/stopping functions. Hardware reset was needed earlier as
getting the software reset working was tricky due to the lack of documentation.
Recently, a number of people using isp116x have said the software reset is
working for them.
I haven't heard of anybody using the clock starting/stopping.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch sets the isp116x to report overcurrent always per-port.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The isp116x chip will now always be in per-port power switching mode. Remove
conf options to set any other mode.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the power-on-to-power-good-time configuration option for
isp116x-hcd.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This just fixes some gfp flags warnings that joined us recently.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rate-limit usblp printer error status messages.
I unplugged my USB printer and almost instantly got several hundred
of these in my kernel message log:
drivers/usb/class/usblp.c: usblp0: error -19 reading printer status
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an entry in the unusual_devs.h file for a Mitsumi card
reader/floppy combo that uses a VIA chipset. The IGNORE_RESIDUE flag was
needed for the second LUN to operate properly.
Signed-off-by: Mihnea-Costin Grigore <mihnea@zulu.ro>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as551) fixes another little problem recently added to the
USB core. Someone didn't fix the type of the first argument to
unregister_chrdev_region.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a /sys/class/usb_device/ class
where every connected usb-device will show up:
tree /sys/class/usb_device/
/sys/class/usb_device/
|-- usb1.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.0/usb1
|-- usb2.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.1/usb2
...
The presence of the "dev" file lets udev create real device nodes.
kay@pim:~/src/linux-2.6> tree /dev/bus/usb/
/dev/bus/usb/
|-- 1
| `-- 1
|-- 2
| `-- 1
...
udev rule:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usb_device %k", NAME="%c"
(echo $1 | /bin/sed 's/usb\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/')
This makes libusb pick up the real nodes instead of the mounted usbfs:
export USB_DEVFS_PATH=/dev/bus/usb
Background:
All this makes it possible to manage usb devices with udev instead of
the devfs solution. We are currently working on a pam_console/resmgr
replacement driven by udev and a pam-helper. It applies ACL's to device
nodes, which is required for modern desktop functionalty like
"Fast User Switching" or multiple local login support.
New patch with its own major. I've succesfully disabled usbfs and use real
nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks
up the udev managed nodes instead of reading usbfs files.
This makes udev to provide symlinks for libusb to pick up:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c"
/sbin/usbdevice:
#!/bin/sh
echo $1 | /bin/sed 's/usbdev\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/'
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To recap: My new G4 powerbook has a bluetooth device that boots up in
what apppears to be a compatability mode - it looks exactly like an HID
keyboard/mouse device.
A special command sequence is sent to switch it into full bluetooth
mode. When this occurs the original HID device vanishes, and a new
(bluetooth HID) USB device appears on the bus with a different product
ID.
The original thread is here:
http://sourceforge.net/mailarchive/message.php?msg_id=12532263
The attached patch adds the device to the hid-core quirks so that
hid-core ignores it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the ftdi_sio driver adds a bunch of new devices and fixes
an incorrect PID:
o Fix PID for ELV UO100 (the PID was in fact for ELV UR100).
o Add PID ELV UR100 (see above) and ELV ALC 8500 Expert.
o Add a whole bunch of other PIDs for ELV USB devices, commented out for
now as they may be used by other drivers eventually. (Christian Abt
of ELV.de submitted a full list of devices including an indication of
which set of drivers are used by default in the MS Windows world. We
decided to comment out the devices that use FTDI's D2XX Windows
drivers by default.)
o Add PIDs for eight devices from Xsens Technologies BV (submitted in a
patch against 2.6.12.2 by Patrick Riphagen).
o Add PID for Falcom Samba GPRS modem (submitted by Sebastian Schubert).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Support one user specified vendor and product ID via a couple
of new module parameters.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This trivial patch makes pl2303 driver work correctly with pl2303HX chip.
Apparently some bug in HX version of pl2303 makes the chip loose some
transmitted bytes or stop working at all after reception of
USB_REQ_CLEAR_FEATURE mesage. Logs generated by UsbSnoop application reveal
that windows driver does not send this type of messages to the converter.
From: "Dariusz M." <D.Marcinkiewicz@elka.pw.edu.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch centralizes the assignment of bcdDevice numbers for different
gadget controllers. This won't improve the object code at all, but it
does save a lot of repetitive and error-prone source code ... and will
simplify the work of supporting a new controller driver, since most new
gadget drivers will no longer need patches (unless some hardware quirks
limit USB protocol messaging).
Added minor cleanups and identifer hooks for the UDC in the Freescale
iMX series processors.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch removes unneeded casts for the following (void *) pointers:
- tty_struct->driver_data
- void *private argument of usb_serial_port_softint()
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reading this driver I noticed some trailing whitespaces and tabs so I
removed them with some 80th column fitting and a few more similar
things.
From: Carlo Perassi <carlo@linux.it>
Signed-off-by: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Carlo Perassi <carlo@linux.it>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Driver core: link device and all class devices derived from it.
To ease the task of locating class devices derived from a certain
device create symlinks from parent device to its class devices.
Change USB host class device name from usbX to usb_hostX to avoid
conflict when creating aforementioned links.
Tweaked by Greg to have the symlink be "class_name:class_device_name" in
order to prevent duplicate links.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C_DEVNAME and i2c_clientname were introduced in 2.5.68 [1] to help
media/video driver authors who wanted their code to be compatible with
both Linux 2.4 and 2.6. The cause of the incompatibility has gone since
[2], so I think we can get rid of them, as they tend to make the code
harder to read and longer to preprocess/compile for no more benefit.
I'd hope nobody seriously attempts to keep media/video driver compatible
across Linux trees anymore, BTW.
[1] http://marc.theaimsgroup.com/?l=linux-kernel&m=104930186524598&w=2
[2] http://www.linuxhq.com/kernel/v2.6/0-test3/include/linux/i2c.h
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge the algorithm id part (16 upper bits) of the i2c adapters ids
into the definition of the adapters ids directly. After that, we don't
need to OR both ids together for each i2c_adapter structure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more users of i2c_algorithm.id, so we can finally drop
this structure member.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When trying to make the hiddev driver issue several Set_Report control
transfers to a custom device with 2.6.13-rc6, only the first transfer in a
row is carried out, while others immediately following it are silently
dropped.
This happens where hid_submit_report() (in hid-core.c) tests for
HID_CTRL_RUNNING, which seems to be still set because the first transfer is
not finished yet.
As a workaround, inserting a delay between the two calls to
ioctl(HIDIOCSREPORT) in userspace "solves" the problem. The
straightforward fix is to add a call to hid_wait_io() to the implementation
of HIDIOCSREPORT (in hiddev.c), just like for HIDIOCGREPORT. Works fine
for me.
Apparently, this issue has some history:
http://marc.theaimsgroup.com/?l=linux-usb-users&m=111100670105558&w=2
Signed-off-by: Stefan Nickl <Stefan.Nickl@kontron.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The device is a Wireless Security Lock (WSL). The device identifies itself
as a Cypress Ultra Mouse. It is, however, not a mouse at all and as such,
shouldn't be handled as one.
Signed-off-by: Brian Schau <brian@schau.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Map custom HID events (such as the ones generated by some Logitech and
Apple Powerbooks USB keyboards) to the FN keycode.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a quirk for the Apple Powermouse, remapping GenericDesktop.Z to
Rel.HWheel, to allow horizontal scrolling in Linux.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a missing break; statement to the URB status handling
in hid-core.c, avoiding flushing the request queue on success.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The hid now supports the Logitech UltraX Media Remote control.
For now, ID 45 on the consumer usage page has been incorrectly
mapped to KEY_RADIO since no other devices uses it.
Signed-off-by: Micah F. Galizia <mfgalizi@csd.uwo.ca>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fixes handling of multi-transaction reports for HID devices. New
function hid_size_buffers() that calculates the longest report
for each endpoint and stores the result in the hid_device object.
These lengths are used to allocate buffers that are large enough
to store any report on the endpoint. For compatibility, the minimum
size for an endpoint buffer set to HID_BUFFER_SIZE rather than the
known optimal case (the longest report length).
It fixes bug #3063 in bugzilla.
Signed-off-by: Michael Haboustak <mike-@cinci.rr.com>
I simplified the patch a bit to use just a single buffer size.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Extend mapping of the consumer usage page in hid-input.c to handle
more cases appearing on new USB keyboards.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add simulation usage page mappings to hid-input.c to support
a new crop of joysticks using them to designate Rudder and
Throttle controls.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove the "list" member of struct sk_buff, as it is entirely
redundant. All SKB list removal callers know which list the
SKB is on, so storing this in sk_buff does nothing other than
taking up some space.
Two tricky bits were SCTP, which I took care of, and two ATM
drivers which Francois Romieu <romieu@fr.zoreil.com> fixed
up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
There's a "return the wrong SKB" error in the GL620A cable minidriver
(for "usbnet") which can oops. This would not appear when talking
Linux-to-Linux, only Linux-to-Windows (for recent Linuxes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Coverity checker.
(akpm: I stole this from Greg's tree and used the (IMO) tidier sizeof(*p)
construct).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When recently addressing remarks by Alexey Dobriyan about
the isp116x-hcd, I introduced a bug in the driver. Please
apply the attached patch to fix it.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch has a one line oops fix, plus related cleanups.
- The bugfix uses microframe scheduling data given to the hardware to
test "is this a periodic QH", rather than testing for nonzero period.
(Prevents an oops by providing the correct answer.)
- The cleanup going along with the patch should make it clearer what's
going on whenever those bitfields are accessed.
The bug came about when, around January, two new kinds of EHCI interrupt
scheduling operation were added, involving both the high speed (24 KBytes
per millisec) and low/full speed (1-64 bytes per millisec) microframe
scheduling. A driver for the Edirol UA-1000 Audio Capture Unit ran into
the oops; it used one of the newly supported high speed modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that I see a bug in hidinput_hid_event. The check for NULL can never
work, becaue &hidinput->input is nonzero at all times.
Cc: <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch does the same swap, i.e. use the ISO macro if (isoc).
Additionally, it fixes the return value - the usb_calc_bus_time function
returns the time in nanoseconds (I didn't notice that before) while the
HS_USECS and HS_USECS_ISO are microseconds. This fixes the function to
return nanoseconds always, and adjusts ehci-q.c (the only high-speed
caller of the function) to wrap the call in NS_TO_US().
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
USB (OHCI) Host driver for S3C2410/S3C2440 based systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201
driver. the only missing part is that the corresponding usbid is not
declared. The following patch should fix this.
From: "Mathieu" <matt@minas-morgul.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch enables a support of KYOCERA AH-K3001V, one of the most
popular cell phone in Japan. This device has vendor specific ID but works
with acm driver by adding USB ID. This device already works on
FreeBSD and OS X by native USB ACM driver with USB ID added.
This device is probed as NO_UNION_NORMAL not to hang up when probing.
Signed-off-by: Masahito Omote <omote@utyuuzin.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch handles a rarely-encountered failure mode in usbcore. It's
legal for device_add to fail (although now it happens even more rarely
than before since failure to bind a driver is no longer fatal). So when
we destroy the interfaces in a configuration, we shouldn't try to delete
ones which weren't successfully registered. Also, failure to register an
interface shouldn't be fatal either -- I think; you may disagree about
this part of the patch.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only uses of both variables were recently removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes an information leak in the usbfs snoop facility:
uninitialized data from __get_free_page can be returned to userspace and
written to the system log. It also improves the snoop output by printing
the wLength value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Fix timeouts in a couple of usb_control_msg() calls due to
change of units from jiffies to milliseconds in 2.6.12.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR. Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch adds the following new devices to the ftdi_sio driver:
* microHAM USB-Y6 and USB-Y8 devices submitted by Justin Burket (KL1RL).
* Evolution Robotics ER1 Control Module submitted by Shawn M. Lavelle.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was already fixed more sufficiently by Andrew Morton's
change 843c944fb8.
Noted by Duncan Sands.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the Option Card driver:
- remove a deadlock
- add sponsor notice
- add new card
- renamed the device to what's usually printed on it
- removed some dead code
- clean up a bunch of irregular whitespace (end-of-line, tabs)
Also add a MAINTAINERS entry for the Option Card driver.
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following driver provides complete interrupt-in and interrupt-out
reports (raw data) to a user program. Until now it uses the
HIDIOCGDEVINFO ioctl call, because I don't know better :-(. Perhaps, it
will be ok for you - and I will be happy, if you assign 8 minor numbers.
I have tested it in several environments and it works very well for me.
However, it has a problem with two or more devices at the same hub, if
the two or more devices need 1 ms interrupt-in transfers. Unfortunately
more than one interrupt-in transfer every ms isn't possible (ehci
driver?). This is why the min_interrupt_in_interval and
min_interrupt_out_interval are increased to 2 ms (see the corresponding
module parameters). This way, I can use two devices simultaneously at
the same hub.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This increases the reference count on the usb cdc acm control interface
which is referred to by the tty interface provided by the driver. This
allows the deferred removal of the tty after the physical device is
disconnected if the tty is held open at the time of disconnection.
Signed-off-by: brian@murphy.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export usb_get_intf and usb_put_intf so that modules can increase
usb interface reference counts.
Signed-off-by: brian@murphy.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A patch re-organizing some parts of root hub initialization deleted the
code initializing the bus-neutral reboot/shutdown notifier for OHCI.
This patch just restores that deleted code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent "pm_message_t" changes removed functionality from the Linux
PM framework. This patch removes it from the OMAP OHCI too, removing
the distinction between (previous) PM_SUSPEND_MEM and PM_SUSPEND_DISK
state transitions ... now the only suspend semantics supportable are
what was previously PM_SUSPEND_DISK (4) and is now "PMSG_SUSPEND" (3).
From: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor OMAP updates that somehow got dropped from previous patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I also needed the following on 2.6.13-rc1 without CONFIG_USB_ETH_RNDIS,
symbol fs_status_desc isn't available in that case on PXA255.
This builds both with and without ETH_RNDIS, but I haven't actually
tested either.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
below you will find one patch to hid-core.c, which lets usbhid ignore
our HID devices. It would be nice, if you can apply it.
Signed-off-by: Michael Hund <mhund@ld-didactic.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The length of the array desc->bitmap is 3, and not 4:
Definitions involved:
In drivers/usb/core/hcd.h
464 #define bitmap DeviceRemovable
In drivers/usb/host/ohci-hub.c
395 struct usb_hub_descriptor *desc
In drivers/usb/core/hub.h
130 struct usb_hub_descriptor {
131 __u8 bDescLength;
132 __u8 bDescriptorType;
133 __u8 bNbrPorts;
134 __u16 wHubCharacteristics;
135 __u8 bPwrOn2PwrGood;
136 __u8 bHubContrCurrent;
137 /* add 1 bit for hub status change; round to bytes */
138 __u8 DeviceRemovable[(USB_MAXCHILDREN + 1 + 7) / 8];
139 __u8 PortPwrCtrlMask[(USB_MAXCHILDREN + 1 + 7) / 8];
140 } __attribute__ ((packed));
In include/linux/usb.h
306 #define USB_MAXCHILDREN (16)
This defect was found automatically by Coverity Prevent, a static analysis
tool.
(akpm: this code should be shot. Field `bitmap' doesn't exist in struct
usb_hub_descriptor. And this .c file is #included in
drivers/usb/host/ohci-hcd.c, and someone somewhere #defines `bitmap' to
`DeviceRemovable'.
>From a maintainability POV it would be better to memset the whole array
beforehand - I changed the patch to do that)
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Cc: <linux-usb-devel@lists.sourceforge.net?
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a basic keypress input driver for the Keyspan Digital
Remote with part number UIA-11. Currently there is an older remote with
part number UIA-10 which isn't supported by this driver. Support for
the older UIA-10 could be added but a binary file is required to be
download to the device, and I don't have that file. I also don't have a
UIA-10 device so I wouldn't be able to test any of the changes.
Signed-off-by: Michael Downey <downey@zymeta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/gadget/net2280.c: In function 'show_registers':
drivers/usb/gadget/net2280.c:1501: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg,
This patch fixes the kmalloc() flags argument type in USB
subsystem; hopefully all of its occurences. The patch was
made against patch-2.6.12-git2 from Jun 20.
Cleanup of flags for kmalloc() in USB subsystem.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sorry that it took so long. Here comes a cleanup patch that
addresses the remarks by Alexey Dobriyan about
gregkh-usb-usb-isp116x-hcd-add.patch EXCEPT the remark about
the typecasting of mem_flags argument for kcalloc; this will
be addressed in a later patch.
OlavCleanup of isp116x-hcd.
Signed off by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make usbmon to print Setup packets of Control transfers. This is useful
when debugging enumeration issues.
This is a change to the trace format which is not fully compatible.
A parser has to look at the data length word now. If that word is
a character like 's', read setup packet before proceeding with data.
I decided not to bump the API tag for this because not many such
parsers exist at this point.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
although 2.6.12 now contains the sisusb driver, it failes to build this
driver due to a missing patch of the Makefile.
From: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We map states 0x00 and 0x10 to the ATM_PHY_SIG_LOST flag. The current logic fails to
resync the line if we get state 0x10 followed by 0x00, since we only resync the line
when the state is 0x00 and the flag changed. Doubly fixed by (1) always resyncing the
line when the state is 0x00 even if the state didn't change, and (2) keeping track of
the last state, not just the flag. We do (2) as well as (1) in order to get better log
messages.
This is a tweaked version of the original patch by Aurelio Arroyo.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No functional change, but less likely to break in the future.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Remove redundant handling of TIOCMBIS and TIOCMBIC ioctls
as they are handled in the tty layer and never reach this driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: Use a single usb_device_id table and detect the type of chip
programatically. The table also flags devices requiring special
initialization. The patch makes the driver about 10K smaller and makes
it easier to add new device IDs.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes an unneeded subclass and protocol from the
07af/0005/100 entry in unsual_devs.h as reported by Alfred Ganz
<alfred-ganz@agci.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently hid-core follows the same code path for input reports
regardless of whether they are a result of interrupt transfers or
control transfers. That leads to interrupt events erroneously being
reported to hiddev for regular control transfers.
Prior to 2.6.12 the problem was mitigated by the fact that
reporting to hiddev is supressed if the field value has not changed,
which is often the case. Said filtering was removed in 2.6.12-rc1 which
means any input reports fetched via control transfers result in hiddev
interrupt events. This behavior can quickly lead to a feedback loop
where a userspace app, in response to interrupt events, issues control
transfers which in turn create more interrupt events.
This patch prevents input reports that arrive via control transfers from
being reported to hiddev as interrupt events.
Signed-off-by: Adam Kropelin <akropel1@rochester.rr.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Catch up with some PCMCIA API changes:
- Docs say that as of 2.6.11 the PCMCIA IRQInfo2 field is ignored,
but it's not yet removed from the API; stop using it anyway.
- As of 2.6.13 PCMCIA finally hotplugs and does driver binding
without "cardmgr"; add a MODULE_DEVICE_TABLE to support this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes CONFIG_PMAC_PBOOK (PowerBook support). This is now
split into CONFIG_PMAC_MEDIABAY for the actual hotswap bay that some
powerbooks have, CONFIG_PM for power management related code, and just left
out of any CONFIG_* option for some generally useful stuff that can be used
on non-laptops as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one-liner fixes a test for interfaces that are already resumed.
It would be nice if this could get into 2.6.12, but it's not critical
since it only affects people doing selective (runtime) suspend/resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a build error on pxa25x processes with pxa2xx_udc and
CONFIG_USB_ETH=m
# CONFIG_USB_ETH_RNDIS is not set
The error is because on that CPU there's no status transfer support
except with RNDIS. Workaround, enable the RNDIS support too.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One debug message won't print the right value; OSDL bugid 4545.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch started life as as527, and was rediffed by me.
Since the IDE interface doesn't convey much information about types of
errors, many USB-IDE adapters report all low-level errors with SK = 0x04,
which is supposed to be used only for non-recoverable errors. As a result
the SCSI midlayer doesn't retry the command. But quite often a retry
would succeed, whereas an unnecessary retry doesn't really hurt anything.
This patch uses a recently-implemented flag to tell the SCSI midlayer that
such hardware errors should be retried.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch causes a port reset whenever there's a transport error or abort.
If that fails it reverts back to doing a mass-storage device reset. It
started life as as497 and was rediffed by me.
This makes error recovery a lot quicker and more reliable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does two things to help reset recovery. It started life as
as496 and was rediffed by me.
First, the patch checks the result of a CLEAR_HALT request and doesn't reset the
endpoint's data toggle unless the request succeeded.
Second, it reduces the timeout for a device reset from 20 seconds to 5
seconds.
If all goes well, then I've finally figured quilt out and this patch should
apply cleanly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
up(&usblp->sem) was called twice in a row in this code path.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> On Sun, Apr 10, 2005 at 07:21:28PM +0600, Viktor A. Danilov wrote:
> >
> > PROBLEM: aiptek input doesn`t register `device` & `driver` section in sysfs (/sys/class/input/event#)
> > REASON: `dev` - field not filled...
> > SOLUTION: in linux/drivers/usb/input/aiptek.c write
> > aiptek->inputdev.dev = &intf->dev;
> > before calling
> > input_register_device(&aiptek->inputdev);
The following (tested) patch fixes the exact same issue with the ATI
Remote input driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for Creative WebCam Go Mini.
Camera has STV680 chip and just different Product ID(0x4007) and Vendor ID (0x041e).
Signed-off-by: Kiril Jovchev <jovchev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initialize status fields in the read and write urbs to prevent a race
condition with open/read/close - open/write/close sequences.
Fixes bug #4432 at bugzilla.kernel.org
Signed-off-by: Adam Oldham <oldhamca@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The itd_patch() function is responsible for allocating entries in the
buffer page pointer list of the iTD. Particularly, a new page pointer
is needed every time when buffer data crosses a page boundary.
However, there is a bug in the allocation logic: the function does not
allocate a new entry when the current transaction is the first
transaction in the iTD (as indicated by first!=0).
The consequence is that, when the data of the first transaction begins
somewhere at the end of a page so that it actually does cross the page
boundary, no new page pointer is allocated. This means that the data
at the end of the first transaction (beyond the page boundary) will be
accessed by the HC using the second page pointer, which is zero.
Furthermore, the first page pointer will be later overwritten by the
page pointers of the other transactions, which will garble it because
the value is or-ed into the iTD field.
All this particular check (for !first) does is cause incorrect
behaviour, so it should be entirely removed (and with it the variable
first that is not used for anything else).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the way uhci-hcd detects valid ports. The
specification doesn't mention any way to find out how many ports a
controller has, so the driver has to use some heuristics, reading the port
status and control register and deciding whether the value makes sense.
With this patch the driver will recognize a typical failure mode (all bits
set to one) for nonexistent ports and won't assume there are always at
least 2 ports -- such an assumption seems silly if the heuristics have
already shown that the ports don't exist.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drain the rndis response queue on disconnect. This fixes a problem
in which an rndis response left in the queue from a previous session
could cause a subsequent session to fail.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a compile glitch with CONFIG_USB_ETH_RNDIS disabled, and
replaces some inline #ifdeffery (and other code) with inline functions
which can evaluate to constants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support to dummy_hcd for suspending and resuming the root
hub and the emulated platform devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the byte-ordering issue for setup packets in the
dummy_hcd driver and cleans up a few things that sparse -Wbitwise
dislikes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
you seem to have applied the original, not the new improved one with
whiter teeth that uses kcalloc instead of kmalloc + memset. Here's a
patch that goes on top of the one you applied.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Work around the gcc-2.95.x macro expansion bug.
Cc: Duncan Sands <baldrick@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Zero the entire instance, not just the struct usbatm_data head.
Make sure the just allocated urb is freed if we fail to allocate
a buffer. Based on a patch by Stanislaw W. Gruszka.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduce the number of "unknown vpi/vci" debug messages to (usually) at most
one per-urb, rather than one per-cell. This is only an issue when (a) many
packets come in but no connection is open; and (b) CONFIG_USB_DEBUG is set.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doesn't do any firmware loading etc, just transmission and reception.
The user needs to take care of modem initialization, and load the
module with parameters giving the endpoints to use and so forth.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver for modems based on the Conexant AccessRunner chipset.
Original patch by Josep Comas, much reworked by Roman Kagan.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Port the speedtch driver to the new usbatm core. The code is much
the same as before, just reorganized, though I threw in some minor
improvements (a new module parameter for choosing the altsetting,
more robust urb failure handling, ...) while I was there.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the core usbatm code: minidrivers (i.e. drivers for particular
modems) now register themselves with the usbatm core, supplying methods
for binding/unbinding etc. The design was inspired by usb-serial and
usbnet. At the same time, more common code from the speedtch and
cxacru (patch 3/5) drivers was generalized and moved into the core. The
transmission and reception parts have been unified and simplified. Since
this is a major change and I don't like underscores in file names,
usb_atm.[ch] has been renamed usbatm.[ch].
Many thanks to Roman Kagan, who did a lot of the coding.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various minor EHCI updates
* Dump some more info in the debug dumps, notably the product
description (e.g. chip vendor), BIOS handhake flags, and
debug port status (when it's not managed by the HCD).
* Minor updates to the BIOS handoff code: always flag the HCD
as owned by Linux (in case BIOS doesn't grab it "early"),
and on the buggy-BIOS path always match the "early handoff"
code and forcibly disable SMI IRQs.
* For the disabled 64bit DMA support, there's now a constant
to use for the mask; use it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has several small updates to the px2xx UDC driver:
* small fixes from Eugeny S. Mints <emints@ru.mvista.com>
- local_irq_save() around potential endpoint disable race
- fix handling of enqueue to OUT endpoints (potential oops)
* add shutdown() method to disable any D+ pullup
* rename methods accessing raw signals, referencing the signals
* describes itself as for "pxa25x", since pxa27x is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sparse updates; and the API change for SETUP packets being in USB byteorder.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is mostly "sparse" related updates, one of which was a missing
le32_to_cpu() should have affected big-endian hardware.
Notable is the API change: setup packets are now provided in USB
byte order. This affects only big-endian hardware, and the gadget
drivers have been updated in a separate patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates most of the gadget framework to expect SETUP packets use
USB byteorder (matching the annotation in <linux/usb_ch9.h> and usage
in the host side stack):
- definition in <linux/usb_gadget.h>
- gadget drivers: Ethernet/RNDIS, serial/ACM, file_storage, gadgetfs.
- dummy_hcd
It also includes some other similar changes as suggested by "sparse",
which was used to detect byteorder bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents gadget drivers from being selected when no controller has
been selected, by adding an additional boolean and depending on it.
It's mostly to help "allmodconfig".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the dummy_hcd driver use emulated root-hub interrupts
instead of polling. It's in the spirit of similar changes being made to
the other HCDs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds to the dummy_hcd driver a new routine for keeping track of
all changes in the state of the emulated USB link. The logic is now kept
in one spot instead of spread around, and it's easier to verify and
update the code. The behavior of the port features has been corrected in
a few respects as well (for instance, if the POWER feature is clear then
none of the other features can be set).
Also added is support for the (relatively new) _connect() and
_disconnect() calls of the Gadget API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the dummy_hcd driver create separate platform devices for
the emulated host controller and emulated device controller. This gives a
more accurate simulation and will permit testing of situations where only
one of the two devices is suspended.
This also changes the name of the host controller platform device to match
the name of the driver. That way the normal platform bus probe mechanism
will handle binding the driver to the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes some cosmetic changes to dummy_hcd:
Minor alterations of comments and whitespace.
Replace USB_PORT_FEAT_xxx with USB_PORT_STAT_xxx. This is
appropriate as the values are stored in a status variable
and they aren't feature indices. Also it allows the
elimination of a bunch of awkward bit shift operations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
