The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous DEBUG_SHIRQ patch missed one case. The console doesn't
set its host descriptors non-blocking.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'request-queue-t' of git://git.kernel.dk/linux-2.6-block:
[BLOCK] Add request_queue_t and mark it deprecated
[BLOCK] Get rid of request_queue_t typedef
2.6.23-rc1 turned up another batch of references from non-__init code to
__init code. In most cases, these were missing __init annotations. In one
case (os_drop_memory), the annotation was present but wrong.
init_maps is __init, but for some reason was being very careful about the
mechanism by which it allocated memory, checking whether it was OK to use
kmalloc (at this point in the boot, it definitely isn't) and using either
alloc_bootmem_low_pages or kmalloc/vmalloc. So, the kmalloc/vmalloc code is
removed.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
COWed devices can't handle more than 32 (64 on x86_64) sectors in one request
due to the size of the bitmap being carried around in the io_thread_req.
Enforce that by telling the block layer not to put too many sectors in
requests to COWed devices.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UML had two wrapper procedures for kmalloc, um_kmalloc and um_kmalloc_atomic
because the flag constants weren't available in userspace code.
kern_constants.h had made kernel constants available for a long time, so there
is no need for these wrappers any more. Rather, userspace code calls kmalloc
directly with the userspace versions of the gfp flags.
kmalloc isn't a real procedure, so I had to essentially copy the inline
wrapper around __kmalloc.
vmalloc also had its own wrapper for no good reason. This is now gone.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
run_helper and run_helper_thread had arguments which were the same in all
callers. run_helper's stack_out was always NULL and run_helper_thread's
stack_order was always 0. These are now gone, and the constants folded
into the code.
Also fixed leaks of the helper stack in the AIO and SIGIO code.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup of the SIGWINCH support.
Some code and comment reformatting.
The stack used for SIGWINCH threads was leaked. This is now fixed by storing
it with the pid and other information, and freeing it when the thread is
killed.
If something goes wrong with a WIGWINCH thread, and this is discovered in the
interrupt handler, the winch record would leak. It is now freed, except that
the IRQ isn't freed. This is hard to do from interrupt context. This has the
side-effect that the IRQ system maintains a reference to the freed structure,
but that shouldn't cause a problem since the descriptor is disabled.
register_winch_irq is now much better about cleaning up after an
initialization failure.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the host side of a console can't be opened, this will now produce visible
error messages.
enable_chan now returns a status and this is passed up to con_open and
ssl_open, which will complain if anything went wrong.
The default host device for the serial line driver is now a pts device rather
than a pty device since lots of hosts have LEGACY_PTYS disabled. This had
always been failing on such hosts, but silently.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup, mostly style violations.
Tidied the includes.
getmaster returns a real errno, which pty_open returns if there's a
problem.
The printks now have severity.
Changed os_* calls to call libc directly.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Major tidying of the xterm console driver:
got rid of the tt-mode gdb support
tidied up the includes
fixed lots of style violations
replaced os_* calls with glibc calls in xterm.c
all printk calls now have a severity indicator
the error paths of xterm_open are closer to being right
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DEBUG_SHIRQ generates spurious interrupts, triggering handlers such as
mconsole_interrupt() or line_interrupt(). They expect data to be available to
be read from their sockets/pipes, but in the case of spurious interrupts, the
host didn't actually send anything, so UML hangs in read() and friends.
Setting those fd's as O_NONBLOCK makes DEBUG_SHIRQ-enabled UML kernels boot
and run correctly.
Signed-off-by: Eduard-Gabriel Munteanu <maxdamage@aladin.ro>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is theoretically possible for a request to finish and be freed between
writing it to the I/O thread and updating the sector count. In this case, the
update will dereference a freed pointer.
To avoid this, I delay the update until processing the next sg segment, when
the request pointer is known to be good.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/kernel.h wherever simple_strtoul is used. This kills a
compile warning in stderr_console.c and potential ones in the other files.
This also fixes a bunch of style violations in exitcode.c.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow a pcap device to be assigned a MAC on the command line. They don't
really need one, but it is handy to be able to do when your distro assigns a
new ethernet device whenever it sees a new MAC.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some network device cleanup.
When setup_etheraddr found a globally valid MAC being assigned to an
interface, it went ahead and used it rather than assigning a random MAC like
the other cases do. This isn't really an error like the others, but it seems
consistent to make it behave the same.
We were getting some duplicate kfree() in the error case in eth_configure
because platform_device_unregister frees buffers that the error cases
following tried to free again.
The pcap initialization routine wasn't doing the proper printk of its
information, causing a printk of the first part of that line to be
unterminated by a newline.
The pcap code had a bunch of style violations, which are now fixed.
pcap_setup wasn't returning false when it detected an unrecognized
option.
The printks in pcap_user all got UM_KERN_BLAH prepended to their
format strings.
pcap_remove now checks for a non-NULL pcap structure before it calls
pcap_close.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename os_{read_write}_file_k back to os_{read_write}_file, delete
the originals and their bogus infrastructure, and fix all the callers.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Formatting fixes ahead of renaming os_{read_write}_file_k to
os_{read_write}_file and fixing all the callers.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all remaining os_{read_write}_file users to use the simple
{read,write} wrappers, os_{read_write}_file_k.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sanitise gfp flags; it actually is an atomic context, so drop the
GFP_KERNEL part.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of writing entire structures between UML and the I/O thread, we send
pointers. This cuts down on the amount of data being copied and possibly
allows more requests to be pending between the two.
This requires that the requests be kmalloced and freed instead of living on
the stack.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Send as many I/O requests to the I/O thread as possible, even though it will
still only handle one at a time. This provides an opportunity to reduce
latency by starting one request before the previous one has been finished in
the driver.
Request handling is somewhat modernized by requesting sg pieces of a request
and handling them separately, finishing off the entire request after all the
pieces are done.
When a request queue stalls, normally because its pipe to the I/O thread is
full, it is put on the restart list. This list is processed by starting up
the queues on it whenever there is some indication that progress might be
possible again. Currently, this happens in the driver interrupt routine.
Some requests have been finished, so there is likely to be room in the pipe
again.
This almost doubles throughput when copying data between devices, but made no
noticable difference on anything else I tried.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch starts the removal of a very old, very broken piece of code. This
stems from the problem of passing a userspace buffer into read() or write() on
the host. If that buffer had not yet been faulted in, read and write will
return -EFAULT.
To avoid this problem, the solution was to fault the buffer in before the
system call by touching the pages that hold the buffer by doing a copy-user of
a byte to each page. This is obviously bogus, but it does usually work, in tt
mode, since the kernel and process are in the same address space and userspace
addresses can be accessed directly in the kernel.
In skas mode, where the kernel and process are in separate address spaces, it
is completely bogus because the userspace address, which is invalid in the
kernel, is passed into the system call instead of the corresponding physical
address, which would be valid. Here, it appears that this code, on every host
read() or write(), tries to fault in a random process page. This doesn't seem
to cause any correctness problems, but there is a performance impact. This
patch, and the ones following, result in a 10-15% performance gain on a kernel
build.
This code can't be immediately tossed out because when it is, you can't log
in. Apparently, there is some code in the console driver which depends on
this somehow.
However, we can start removing it by switching the code which does I/O using
kernel addresses to using plain read() and write(). This patch introduces
os_read_file_k and os_write_file_k for use with kernel buffers and converts
all call locations which use obvious kernel buffers to use them. These
include I/O using buffers which are local variables which are on the stack or
kmalloc-ed. Later patches will handle the less obvious cases, followed by a
mass conversion back to the original interface.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define release methods for the ubd and net drivers. They contain as much of
the remove methods as make sense. All error checking must have already been
done as well as anything else that might be holding a reference on the device
kobject.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
userspace code used to have to call the kernelspace function page_size() in
order to determine the value of the kernel's PAGE_SIZE. Since this is now
available directly from kern_constants.h as UM_KERN_PAGE_SIZE, page_size() can
be deleted and calls changed to use the constant.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calls lines_init() *after* xterm_title is modified to include umid.
Signed-off-by: Davide Brini <davide.brini@unibo.it>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To look at users I did:
$ find arch/um/ include/asm-um -name '*.[ch]'|xargs grep -r 'net_kern\.h'
+-l|xargs grep '\<user\>'
Most users just cast user to the appropriate pointer, the remaining ones are
fixed here. In net_kern.c, I'm almost sure that save trick is not needed
anymore, but I've not verified it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid using the temporary buffer introduced by previous patch to hold the
device name.
Btw, avoid leaking device on an error path. Other error paths may need
cleanup.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve checking and diagnostics for broadcast and multicast Ethernet MAC
addresses, and distinguish between those cases in output; also make sure the
device is assigned a MAC address valid only locally to avoid collisions.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
user_util.h isn't needed any more, so delete it and remove all includes of it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rescue the useful contents of the soon-to-be-gone user-util.h.
pty.c now gets ptsname from stdlib.h like it should have always done.
CATCH_EINTR is now in os.h, although perhaps all usage should be under
os-Linux at some point.
get_pty is also in os.h.
This patch restores the old definition of ARRAY_SIZE in user.h. This file is
included only in userspace files, so there will be no conflict with the
kernel's new ARRAY_SIZE. The copy of the kernel's ARRAY_SIZE and associated
infrastructure is now gone.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a number of problems associated with network interface hotplug.
The userspace initialization function can fail in some cases, but the
failure was never passed back to eth_configure, which proceeded with the
configuration. This results in a zombie device that is present, but can't
work. This is fixed by allowing the initialization routines to return an
error, which is checked, and the configuration aborted on failure.
eth_configure failed to check for many failures. Even when it did check,
it didn't undo whatever initializations has already happened, so a present,
but partially initialized and non-working device could result. It now
checks everything that can fail, and bails out, undoing whatever had been
done.
The return value of eth_configure was always ignored, so it is now just
void.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bunch of formatting violations in the drivers:
return(n) -> return n
whitespace fixes
emacs formatting comment removal
breaking if(foo) return(n) into two lines
There are also a couple of errno use bugs:
using errno in a printk when the failure put errno into a local variable
saving errno after a printk, which can change it
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a disk fails to open, i.e. its host file doesn't exist, it won't be
removable because the hot-unplug code checks the existence of its gendisk.
This won't exist because it is only allocated for successfully opened disks.
Thus, a typo on the command line can result in a unusable and unfixable disk.
This is fixed by freeing the gendisk if it's there, but not letting that
affect the removal.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment immediately preceding this points out, this list is changed in
irq context, so it needs to be protected with spin_lock_irqsave in process
context when it is processed.
Sometimes, gcc should just compile the comments and forget the code.
The IRQ side of this was better, in the sense that it blocked and unblocked
interrupts, but it still should have saved and restored them.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a NULL dereference when unplugging a device. The default value of
err_msg wants to be "" in case the driver doesn't modify it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 62f96cb01e introduced per-devices
queues and locks, which was fine as far as it went, but left in place a
global which controlled access to submitting requests to the host. This
should have been made per-device as well, since it causes I/O hangs when
multiple block devices are in use.
This patch fixes that by replacing the global with an activity flag in the
device structure in order to tell whether the queue is currently being run.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid reusing userspace errno twice - it can be cleared by libc code
everywhere (in particular printk() does clear it in my setup).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix confusion about call context - comments and code are inconsistent and
plain wrong, my fault.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since both UML consoles do not use percpu variables, they may be called when
the cpu is still offline, and they may be marked CON_ANYTIME (this is
documented in kernel/printk.c, grep for CON_ANYTIME to find mentions of this).
Works well in testing done with lock debug enabled, should be safe but is not
needed for next release.
This would probably help also stderr_console.c, but this is yet to test.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memory allocated by mcast_user_init must be freed in the matching mcast_remove.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Of kernel subsystems that work with pids the tty layer is probably the largest
consumer. But it has the nice virtue that the assiation with a session only
lasts until the session leader exits. Which means that no reference counting
is required. So using struct pid winds up being a simple optimization to
avoid hash table lookups.
In the long term the use of pid_nr also ensures that when we have multiple pid
spaces mixed everything will work correctly.
Signed-off-by: Eric W. Biederman <eric@maxwell.lnxi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
