[PATCH] [NET] mv643xx: add workaround for HW checksum generation bug
The hardware checksum generator on the mv64xxx occasionally generates
an incorrect checksum. This patch works around the issue and enables
hardware checksum generation.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Patch Description:
This patch incorporates the following hardware fixes required
for Xframe II adapter.
1. New values to program the dtx_control register.
2. Disable memory controller interrupts(MC_INTR) since these
are now monitored thru' a poll routine.
3. Don't reset an XframeII card on an ECC double-bit error(It
can recover).
4. Save/restore PCI config space before/after a reset irrespective
of Xframe I or II card.
5. Bumped up the driver version no. to 2.0.3.1
Please review the patch and apply the same if it looks ok.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Now that all tms380 devices have a valid
struct device with dma_mask, remove dmalimit from tmsdev_init().
Kconfig: depend tms380tr and madgemc on MCA.
abyss.c, proteon.c, skisa.c, tmspci.c, tms380tr.h:
remove dmalimit parameter from tmsdev_init().
tms380tr.c: use device->dma_mask instead of dmalimit.
madgemc.c: move to new MCA API using struct device.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A problem was reported by Grant Grundler on an HP rx8620 using IOX
Core LAN partno(A7109-6) 5701 copper NIC. The tg3 driver mistakenly
detects this NIC as having a SerDes PHY and link does not come up as a
result.
The problem was caused by an incorrectly programmed eeprom that set the
NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit in the NIC_SRAM_DATA_CFG location.
This patch will override the NIC_SRAM_DATA_CFG_PHY_TYPE_FIBER bit if a
valid PHY ID is read from the MII registers on older 570x chips where
the MII interface is not used on SerDes chips. On newer chips such as
the 5780 that use MII for both copper and SerDes, SerDes detection must
rely on the eeprom.
This patch will make the SerDes detection identical to versions 3.25 and
older.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/e1000/e1000_main.c: In function `e1000_clean_tx_irq':
drivers/net/e1000/e1000_main.c:2774: warning: size_t format, dma_addr_t arg (arg 8)
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The multicast code of the fmvj18x_cs driver is broken.
I fixed it to work properly.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SIS190 must select MII since it's using it.
While I was editing the Kconfig entry, I also converted the spaces to
tabs.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The Linksys EG1032 uses Realtek's 8169 chipset.
Credit goes to Bob Wilson <bwilson4web@hotmail.com> for the report.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use msleep_interruptible() instead of delay_cycx() to guarantee the task
delays as expected. Remove the prototype and definition of delay_cycx().
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Rdiger found a bug in nv_open that explains some of the reports
with duplex mismatches:
nv_open calls nv_update_link_speed for initializing the hardware link speed
registers. If current link setting matches the values in np->linkspeed and
np->duplex, then the function does nothing.
Usually, doing nothing is the right thing, but not in nv_open: During
nv_open, the registers must be initialized because the nic was reset.
The attached patch fixes that by setting np->linkspeed to an invalid value
before calling nv_update_link_speed from nv_open.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The DM9000 driver is responding to ioctl() calls it should not be. This
can cause problems with the wireless tools incorrectly indentifying the
device as wireless capable, and crashing under certain operations.
This patch also moves the version printk() to the init call, so that
you only get it once for multiple devices, and to show it is loaded
if there are no defined dm9000s
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix DM9000 driver usage of spinlocks, which mainly came to light
when running a kernel with spinlock debugging. These come down to:
1) Un-initialised spin lock
2) Several cases of using spin_xxx(lock) and not spin_xxx(&lock)
3) move the locking around the phy reg for read/write to only
keep the lock when actually reading or writing to the phy.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After suspend the driver needs to retest link status in case the cable
has been inserted or removed during the suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Using the right register clearly improves chances of getting the MII
code and thus the driver working at all.
- On startup check the media type before setting up duplex or we might
spend the first 1.2s with a wrong duplex setting.
- Get rid of whitespace lines.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The flush threshold in the MAC chip should be increased.
Found while reviewing vendor version of sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages. Handle this situation
cleanly by masking away at boot time.
Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c | 24 ++++++++++--------------
drivers/net/skge.h | 8 ++++++--
2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace remaining WLAN_FC_* defines with the ones used in ieee80211
header file. This completes the move from hostap version of frame
control field processing to ieee80211 version.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove backwards compatibility define for WLAN_CAPABILITY_ESS now that
net/ieee80211.h defines this.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
IEEE 802.11 has a capability field flag called ESS, but ieee80211 had
renamed this to BSS for some reason. hostap has been using
WLAN_CAPABILITY_ESS and since that matches with the standard, lets use
it as the name for this define. Add WLAN_CAPABILITY_BSS as a backwards
compatibility name for the same bit since ieee80211 and ipw2200 are
using this and there are versions outside kernel tree that expect to
find this define name.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace temporary HOSTAP_FC_GET_{TYPE,STYPE} macros with the ieee80211
version of WLAN_FC_GET_{TYPE,STYPE}.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused defines that are already available from generic kernel
header files.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace hardware model specific #ifdef's in struct local_info with
void *hw_priv that is pointing to cs/pci/plx specific data
structure. This removes unneeded #ifdef's and as such, is a step
towards making it possible to share objects for hostap_hw.c and
hostap_download.c with cs/pci/plx drivers without having to compile
and link the same code separately for each one.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PCI version of Prism2.5/3 has undocumented DMA support for TX/RX data,
but this seems to have some hardware bugs that prevent it from being
used properly for TX. RX side could possibly be made to work reliably.
Even though DMA support would be very useful for saving host CPU (from
about 40% to 5-10% when operating at maximum throughput), it seems to
be best to just remove this code finally. The implementation has
always been commented out by default and has received very limited
testing. The code may have already been broken number of times and I
don't have much interested in trying to verify whether it works or
not. Getting this out makes it easier to maintain the driver and
allows some cleanups that have been partly postponed because of this
experimental bus master/DMA code.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Old AP mode code for power saving was using skb->cb for couple of
flags before the more generic 802.11 TX code started using the same
buffer for struct hostap_skb_tx_data. This resulted in the power save
code corrupting the magic value in beginning of the buffer and TX code
dropping the power saved packets because of this for the case where
STAs send PS-Poll frames with PwrMgmt flag set.
This patch modifies the power save code to use the same struct
hostap_skb_tx_data as rest of the TX path in order to avoid corrupting
the data in skb->cb.
In addition, this patch reorders fields in the structure and makes
them use smaller types in order to make the structure fit in skb->cb
on 64-bit hosts.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Suggested by Steven Rostedt, matches his patch included in e100.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined buffer_info-dma to be dma_addr_t instead of uint64
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused functions, render some variable static instead of global - based on patch from Adrian Bunk
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix data output by ethtool -d
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use netdev_priv() instead of netdev->priv
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix unnecessary link state messages
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Set RXDCTL:PTHRESH/HTHRESH to zero
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add the device ID of the Buffalo AirStation WLI-CF-S11G
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to incorporate comments from earlier 12 patches.
It also fixes a few issues we found during this time.
Following is a list of changes in this patch. Item 1 incorporates
earlier comments. Issues addressed in items 2 to 4 were discovered
recently.
1. wmb() call in s2io_xmit() replaced with mmiowb().
2. The dtx_control register was earlier programmed incorrectly
for Xframe II adapter.
3. As suggested by hardware team, after a reset, in case of
Xframe II adapter, we clear certain spurious errors by
clearing PCI-X ECC status register, "detected parity error"
bit in PCI_STATUS register and PCI_STATUS bit in txpic_int register.
4. On IBM PPC platforms, we found that in the Rx buffer replenish
function, two memory writes(one to the the descriptor length and
another to the ownership) were getting reordered. This was causing
the adapter to see the ownership transfered to it before the length
was updated.
One solution was to add a wmb() but since this would turnout expensive
on some platforms if called for every descriptor, we set the ownership
bit and other fields of '2' to 'N' Rx descriptors followed by a wmb()
and then set the ownership of first descriptor ('1').
Here the value 'N' is configurable by making it a module loadable
parameter (rxsync_frequency).
(NOTE: This parameter is a power of 2).
5. Bumped up the driver version no. to 2.0.2.1
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The last patch in this series fixes the following issues found during
testing.
1. Ensure we don't pass zero sized buffers to the card(which can lockup)
2. Restore the PCI-X parameters(in case of Xframe I adapter) after a reset.
3. Make sure total size of all FIFOs does not exceed 8192.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The below patch implements a new "Link state change handling"
scheme supported by the Xframe II adapter. It also bumps up the
driver version to 2.0.2.0.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This is a patch to provide bimodal interrupt moderation support for
Xframe II adapter. Basically, in this moderation scheme, the adapter
raises a traffic interrupt if the no. of packets transmitted and/or
received reaches a programmable threshold.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch implements the slow-path handling functions(link
state change, hardware errors) as a timer. It is not
handled in interrupt handler as was done previously.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch relates to mostly performance related changes.
1. Fixed incorrect computation of PANIC level in rx_buffer_level().
2. Removed unnecessary PIOs(read/write of tx_traffic_int and
rx_traffic_int) from interrupt handler and removed read of
general_int_status register from xmit routine.
3. Enable two-buffer mode(for Rx path) automatically for SGI
systems. This improves Rx performance dramatically on
SGI systems.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch fixes certain memory leaks discovered in free_tx_buffers()
and rx_osm_handler()
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch includes fixes for few purely software bugs identified
since last release.
1. Keep track and display(as part of ethtool command output) the no.
of single-bit and double-bit ECC errors.
2. Handle race condition between intr handler and "interface down"
routine.
3. Initial link state setting modified so that the link state displayed
after "interface Up" is correct.
4. Fix for "Incorrect Tx packet count when TSO is enabled".
5. Disable periodic DMA of statistics and schedule one-shot DMA
only when required.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix the p-persistence CSMA algorithm which in simplex mode was starting
with a slottime delay before doing anything else as if there was carrier
collision resulting in bad performance on simplex links.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Else on SMP systems it is possible for hotplug to execute,
invoke tg3_open(), and end up loading the uninitialized
PCI register save area into the card.
Signed-off-by: David S. Miller <davem@davemloft.net>
cs89x0 talks a lot at boot. Seems like debug leftover. This patch
downgrades printks to KERN_DEBUG. While we're at it, make these messages a
bit less obscure.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make it compile with CONFIG_PM=n
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drivers really only work well in SMP if they actually can be selected.
This is a leftover from the time when the 6pack drive only used to be
a bitrotten variant of the slip driver.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Kconfig | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Whitespace cleanup for loopback driver. Hopefully it fixes the last few
annoyances.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch slightly optimizes the loopback driver's stats update.
Saves two loads, one add and one increment per packet sent.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch #ifdefs the TSO code in the loopback driver.
Saves ~800 bytes of text on i386 and avoids a conditional in the fast path.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
--ReaqsoxgOBHFXBhH
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
Hi Jeff,
Here's a little patch fixing a typo in smc91x.h.
Regards,
Tony
--ReaqsoxgOBHFXBhH
Content-Type: text/x-chdr; charset=us-ascii
Content-Disposition: inline; filename="patch-fix-typo-smc91x.h"
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use module_param() instead of the old MODULE_PARM()
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Yukon-Lite chipset needs workaround for revision 7 (or later).
Without this patch, chip gets stuck in low power mode and never
boots. Newer SysKonnect vendor code already had same patch.
Related bug in skge is http://bugs.gentoo.org/87822
Chris, please add for 2.6.12.2
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup code that is used to toggle LED's. Since we
get called from ethtool, can use that thread rather than
setting up a timer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
During autonegotiation set PHY interrupt mask to ignore
bogus speed change interrupts.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The code to clear fifo errors was incorrect and sending garbage
to the external phy. Removed the no longer used inline's funcs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The check for Yukon lite changes was restricting itself to
rev A3. It turns out that these changes are also true on A4
and later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleanup the phy_lock deadlock because of relocking in the nway_reset path.
Reported by Francois Romieu.
Also, don't need to do irqsave/restore for blink,
just excluding bh is good enough.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Here is a fix for a typo, thanks Eliot Dresselhaus.
Since transmitter not active when device is down, it wasn't really noticed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The SK-9E boards use the Marvell Yukon2 chipset which
is not supported by the skge driver. Thanks to Ralph Roesler
for noticing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Using Genesis board, I get harmless error reports. Rather than console
error, turn it into a error counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
A few sparse cleanups for orinoco.c
Signed-off-by: Peter Hagervall <hager@cs.umu.se>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch makes tms380tr use the new DMA API. Now that on Alpha, this API
also supports bus master DMA for ISA (platform) devices, i changed the
driver to use this new API.
This also works around a bug in the firmware loader: The example provided
in Documentation/firmware_class no longer works, as the firmware loader now
calls get_kobj_path_length() and the kernel promptly oopses, as the
home-grown device doesn't have a parent. Of course, this doesn't happen
with a "real" device which has its bus (or pseudo bus in the case of
platform) as parent.
Converted tms380tr to use new DMA API:
- proteon.c, skisa.c: use platform pseudo bus to create a struct device
- Space.c: delete init hooks
- abyss.c, tmspci.c: pass struct device to tms380tr.c
- tms380tr.c, tms380tr.h: new DMA API, use real device fo firmware loader
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In ALB mode, allow new slave to use bond's MAC address if the new
slave's MAC address is being used within the bond and no other slave
is using the bond's MAC address.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace Host AP version of WEP, TKIP, CCMP implementation with
net/ieee80211 that has more or less identical implementation (since
it is based on the Host AP implementation). Remove Host AP specific
implementation and modules from drivers/net/wireless/hostap.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Preparations for starting to use net/ieee80211 instead of private
IEEE 802.11 implementation. Include net/ieee80211.h and
net/ieee80211_crypt.h into files that will be needed these in the
future. Remove duplicate definitions from hostap_common.h and
rename WLAN_FC_GET_{TYPE,STYPE} macros for now sinc net/ieee80211.h
is using incompatible definitions. This will be resolved in the
future by updating Host AP to use the versions that do not shift
type/stype.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethernet drivers to remain as ignorant as is reasonable of the connected
PHY's design and operation details.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The station control register must depend on both the advertisement and the lpa
The link partner ability has better be intersected with the current
advertised value before it is feed to the station control register.
Sight-catched-by: Lars Vahlenberg <lars.vahlenberg@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added PHY identifier for the Asus K8S-MX motherboard
Note: the same ID appears in the sis900 driver.
Signed-off-by: Lars Vahlenberg <lars.vahlenberg@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a dummy read before accessing the status register
SiS driver suggests it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Allow a non-hardcoded ID for the PHY
This is the first step before the driver probes for the PHY address.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
extract bits definition from SiS driver
- fix the Rx stats;
- minor pieces of documentation.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add a restriction to the size of the Rx buffer
SiS driver forces the size of any Rx buffer to be a multiple of 64 bit.
I would not be surprized that it goes along with some alignment issues
which have been experienced before. So far it does not make much of a
difference (both drivers use 1536 bytes buffer).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Extract some mac addr code from SiS's driver.
Some magic may hide beyond the isa bridge. The Rx mac control
register is now set without condition.
Note: good or bad, this part of the code is quite close to sis900.c.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Replace hardcoded constants by enumerated values in sis190_read_eeprom
The names of the enumerated values have been extracted from SiS'official
driver (v1.00.00 published on 2005/07/11).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Merge some register related information from SiS driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
ethtool/mii support
Bug: disabling autonegotiation and setting the link parameters at the
same time does not provide the expected result. More investigation is
needed.
Note: past the initial probe/open time, the link is managed from user-space
or accessed through sis190_phy_task, i.e. in a usermode context. Whence the
very limited locking needs.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
netconsole support.
This stuff should be factored out of every driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Raise the sis190 driver from the dead
The driver handles the integrated network device found on SiS 965L
chipset. It follows the classical (non-napi) interrupt-driven model
and provides minimal ethtool support.
The code comes from a heavy cleanup/rewrite of the original code
which was removed from the kernel on 14/04/2004. Since the r8169
driver does not work too bad and there will probably be (at least)
a few months of improvements/testing/fixing, I made the code as
close as possible to the r8169 one.
Pascal Chapperon <pascal.chapperon@wanadoo.fr> deserves some special
credit for testing and bug-catching. Many thanks to Lars Vahlenberg
as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixed beacon frame when moving from monitor mode to master mode
(workaround for firmware bug that left IBSS IE in the Beacon
frames). This is using the same workaround that was previously used
when moving from adhoc mode to master mode.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Warning fix for 64-bit platforms
Hello!
The patch fixes following warning seen on 64-bit platforms (in my case -
x86_64, gcc-4.0):
In file included from /usr/local/src/hostap/driver/modules/hostap_cs.c:203:
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit_cb?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1674: warning: cast from pointer to integer of different size
/usr/local/src/hostap/driver/modules/hostap_hw.c: In function ?prism2_transmit?:
/usr/local/src/hostap/driver/modules/hostap_hw.c:1758: warning: cast to pointer from integer of different size
prism2_transmit_cb uses a (void *) argument to get an integer. A
simple fix would be to use double cast from pointer to long and then to
int (and vice versa when int is passed as a pointer). But I prefer a
slightly longer patch.
I believe that whenever an argument can hold both a pointer and an
integer, it should be declared long. long can hold both pointers and
integers (except win64, but we are not coding for Windows), it can be
cast to both of them and it's never assumed to be a valid pointer, which
could be useful for some automatic code checkers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
line 129 of hostap_80211_rx.c should read:
LWNG_SETVAL(mactime, 2, 0, 4, rx_stats->mac_time);
not:
LWNG_SETVAL(mactime, 2, 0, 0, rx_stats->mac_time);
The length field is incorrect.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Firmware seems to be getting into odd state in host_roaming mode 2
when hostscan is used without join command, so try to fix this by
re-joining the current AP. This does not actually trigger a new
association if the current AP is still in the scan results.
This makes background scans (iwlist wlan0 scan) not to break data
connection when in host_roaming 2 mode, e.g., when using wpa_supplicant.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cleaned up scan result processing by converting struct
hfa384x_scan_result into struct hfa384x_hostscan_result. This removes
special cases from result processing since the results are only used
in one, hostscan, format.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Added support for setting channel mask for scan requests
('iwpriv wlan0 scan_channels 0x00ff' masks scans to use channels 1-8).
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add MODULE_VERSION information for the Host AP kernel modules and
update the version string to indicate which version of the external
Host AP driver is included in the kernel tree.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
pcmcia id_table for hostap_cs.c
Hi Jouni,
Here's a patch for adding a pcmcia id_table to hostap_cs.c as introduced
by the PCMCIA subsystem changes in linux-2.6.13-rc1. The id_table allows
hotplug (along with pcmciautils [1]) to load the driver without the need
for the pcmcia-cs cardmgr daemon.
The id_table was generated from the CVS version of hostap_cs.conf using
a script borrowed from Dominik Brodowski. I have removed any duplicate
entries, but I have only been able to test the functionality of the
patch with a Linksys WPC11v3.
Sincerely,
Brix
[1]: http://www.kernel.org/pub/linux/utils/kernel/pcmcia/
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Create sysfs "device" files for hostap
I was writing some scripts to automatically build kismet source lines,
and I noticed that hostap devices don't have device files, unlike my
prism54 and ipw2200 cards:
$ ls -l /sys/class/net/eth0/device
/sys/class/net/eth0/device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:02:01.0
$ ls -l /sys/class/net/wifi0
ls: /sys/class/net/wifi0/device: No such file or directory
$ ls -l /sys/class/net/wlan0
ls: /sys/class/net/wlan0/device: No such file or directory
The following (quite small) patch makes sure that both the wlan and wifi
net devices have that pointer to the bus device.
This way, I can do things like
for i in /sys/class/net/*; do
if ! [ -e $i/device/drive ]; then
continue;
fi;
driver=$(basename $(readlink $i/device/driver))
case $driver in
hostap*)
echo -- hostap,$i,$i-$driver
break;
ipw2?00)
echo -- $driver,$i,$i-$driver
break;
prism54)
echo prism54g,$i
esac
done
Which should generate a working set of source lines for kismet no matter
what order I plug the cards in.
It might also be handy to have a link between the two net devices, but
that's a patch for another day.
That patch is against 2.6.13-rc1-mm1.
-- Dave
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_cs: Remove irq_list, irq_mask and pcmcia/version.h
Remove irq_list, irq_mask and pcmcia/version.h as suggested in
http://kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
EXPORT_SYMTAB does nothing. There's no need to define something if it
doesn't have any effect.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update hostap_cs to use new PCMCIA event callback registration.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
An early version of the sk98lin patch was merged via Len's tree. But there
were subsequent updates as a result of review from Jeff. THis fixes things
up.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We want to extract our LAN card driver from tulip core driver and
make a new file uli526x.c at tulip folder, because we have added
some ethtool interface support and non-eprom support in our driver
and may be other change in the futher.
If our controllers support are still contained in the tulip core
driver, I think it'll increase the complexity of maintenance, you
know, tulip core driver include several files and support so many
other controllers. Furthermore, I tested the newest kernel 2.6.12
and I found the tulip driver can not work on our lan controller, and
I no time to debug it, so I aspired want to make a single uli526x.c
file just for our controllers. Could you help us remove the ULi
m5261/m5263 lan controller support from tulip core driver and add
the new single uli526x.c file for us?
Signed-off-by: Peer Chen <Peer.Chen@uli.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
sys_reboot() now calls device_suspend(), so it is no longer necessary for
the e1000 driver to register a reboot notifier [in fact doing so results in
e1000_suspend() getting called twice].
(akpm: we need to fast-track this. It's causing ia64 to oops on shutdown)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: <cramerj@intel.com>
Cc: <john.ronciak@intel.com>
Cc: <ganesh.venkatesan@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove duplicates from the device id table.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
turn many #if $undefined_string into #ifdef $undefined_string to fix some
warnings after -Wno-def was added to global CFLAGS
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move in_aton to allow netpoll and pktgen to work without the rest of
the IPv4 stack. Fix whitespace and add comment for the odd placement.
Delete now-empty net/ipv4/utils.c
Re-enable netpoll/netconsole without CONFIG_INET
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggestion from Sam Ravnborg <sam@ravnborg.org>
It causes all driver families to be displayed aligned immediately under the
main network drivers heading (in menuconfig/xconfig/gconfig) instead of
not being subordinate to (i.e., not indented) the Network device support
heading at all.
The improved network driver families are:
token ring, wireless, PCMCIA, WAN, ATM, and S390.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780S support by adding a new tg3_setup_fiber_mii_phy() function and
a timer function for parallel link detection. 5780S uses standard MII
registers for 1000BaseX and runs in GMII mode as opposed to TBI mode on
older serdes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disallow jumbo TSO on 5780 due to hardware restrictions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate all DMA watermark settings for standard and jumbo frames on
all chips in tg3_init_bufmgr_config() and add new settings for 5780.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rx_pkt_buf_sz to the tg3 structure to support variable buffer
sizes on the standard ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic jumbo frames support for 5780. This chip supports jumbo frames
on the standard receive ring without the jumbo ring. The
TG3_FLAG_JUMBO_ENABLE is changed to TG3_FLAG_JUMBO_RING_ENABLE to
indicate using the jumbo ring on 5704 and older chips. A new
TG3_FLG2_JUMBO_CAPABLE flag is added to indicate jumbo frames support
with or without the jumbo ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5780 PCI IDs, chip IDs, and other basic support.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETCONSOLE=y and INET=n results in the following compile error:
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
net/built-in.o: In function `netpoll_parse_options':
: undefined reference to `in_aton'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put NETCONSOLE and NETPOLL options together since they are related.
This cuts down on the hassle of flipping back and forth between
the Networking menu and the Network drivers menu to change their
config settings.
Tested with menuconfig, gconfig, and xconfig.
gconfig has a small problem with this. I think that it's
a bug in gconfig and I will take it up with Romain Lievin.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Use of the time_after() macro, defined at linux/jiffies.h, which deal
with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tr_type_trans(), hippi_type_trans() left as-is.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.
The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.
Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should do this:
.suspend()
pci_disable_device()
.resume()
pci_enable_device()
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This is part of the grand scheme to eliminate the qlen
member of skb_queue_head, and subsequently remove the
'list' member of sk_buff.
Most users of skb_queue_len() want to know if the queue is
empty or not, and that's trivially done with skb_queue_empty()
which doesn't use the skb_queue_head->qlen member and instead
uses the queue list emptyness as the test.
Signed-off-by: David S. Miller <davem@davemloft.net>
As a follow-up, remove the inclusion of pcmcia/version.h in many files.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "event handler" to struct pcmcia_driver -- the unified event handler
will disappear really soon, but switching it to struct pcmcia_driver in the
meantime allows for better "step-by-step" patches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few more u32 vs. pm_message_t fixes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for some new PHY models to sungem as used on some
recent Apple iMac G5 models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the usage of struct of_match to struct of_device_id,
similar to pci_device_id. This allows a device table to be generated,
which can be parsed by depmod(8) to generate a map file for module
loading.
In order for hotplug to work with macio devices, patches to
module-init-tools and hotplug must be applied. Those patches are
available at:
ftp://ftp.suse.com/pub/people/jeffm/linux/macio-hotplug/
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave, you were right and the sleeping locks in shaper were
broken. Markus Kanet noticed this and also tested the patch below that
switches locking to spinlocks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ethtool -C with verification of user parameters.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
Those are big, slow and generally not recommended for kernel code.
They are even not present on i386. So it should be concluded that
one could as well get away with do_div() alone.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many drivers use skb->tail unnecessarily.
In these situations, the code roughly looks like:
dev = dev_alloc_skb(...);
[optional] skb_reserve(skb, ...);
... skb->tail ...
But even if the skb_reserve() happens, skb->data equals
skb->tail. So it doesn't make any sense to use anything
other than skb->data in these cases.
Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers. It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.
Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge. In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Now we can change the pci core to always set this pointer, as pci drivers
should use it, not the driver core callback.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More fixes for greg depredations.
Also nuke lots of pointless typecasts.
All this new wireless code adds near-infinite amounts of trailing whitespace.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/wireless/ipw2100.c: In function `ipw2100_set_key_index':
drivers/net/wireless/ipw2100.c:5326: array index in non-array initializer
drivers/net/wireless/ipw2100.c:5326: (near initialization for `cmd')
drivers/net/wireless/ipw2100.c:5326: warning: missing braces around initializer
drivers/net/wireless/ipw2100.c:5326: warning: (near initialization for `cmd.host_command_parameters')
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix few typos/thinkos in ipw, remove ugly macro (it is commented around,
anyway), and fix types passed to pci_set_power_state.
Signed-off-by: Andrew Morton <akpm@osdl.org>
There are several never used macros in ipw2100. This removes them.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
ipw2100 still has support for old kernels. Thats considered bad for patch in
mainline... this fixes few instances.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom macros.
This patch includes dma-mapping.h explicitly because it caused errors on some
architectures otherwise. See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom macros.
This patch includes dma-mapping.h explicitly because it caused errors on some
architectures otherwise. See
http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
On Mon, 06 Jun 2005 14:29:52 +0800, Zhu Yi wrote:
> ("%zd", sizeof()) should be better.
Thanks. This is a corrected version of the patch.
This patch fixes warnings when compiling ipw2100 and ipw2200 on x86_64.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: Jirka Bohac <jbohac@suse.cz>
This results in recursive dependencies:
- IPW2200 depends on NET_RADIO
- IPW2200 selects IEEE80211
- IEEE80211 selects NET_RADIO
This patch fixes the IPW2200 dependencies in a way that they are similar
to the IPW2100 dependencies.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
The amd8111e driver directly assigns the DMA mask to the dma_mask
member of the struct pci_dev instead of using pci_set_dma_mask(). This
makes the call to pci_dma_supported() redundant as pci_set_dma_mask()
does this check.
I do not own this device so I only compile-tested this patch.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
For boards that invert the SMC91x IRQ line (maybe an FPGA inverts it),
the set_irq_type() call can't assume IRQT_RISING. These particular
boards currently use OMAP-specific calls to change the trigger type,
but the boards break when set_irq_type() stops being a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add new pcmcia id_table for fmvj18x_cs and serial_cs.
(TDK multi-function card (NetPartner9610 and MobileNetworker3200))
Signed-off-by: Jun Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Need to handle receive and transmit packet arbiter timeouts.
Transmit arbiter timeouts happens when Gigabit sends to 100Mbit port
on same switch and pause occurs.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Cleanup messages (for debug) about PHY interrrupts, because when
user can't get driver working that is often the problem.
Use a consistent way of enabling interrupts by port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Rewrite the code for handling the Broadcom PHY to something that
works. Remove link polling because Broadcom and Yukon don't need it.
When I wrote initial code, didn't have a genesis chipset based
board to test, so it was a non-working guess.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Remove support for the non-Broadcom genesis based boards. The code
is untested, and probably won't work as is. The newer boards are all
Yukon based, and only old Genesis board I can find uses Broadcom.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Remove the bits and pieces added relating to Yukon II chipset.
The Yukon 2 will be in a separate driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Replace inline accessor functions for chip revision and number of ports
with simple structure members.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The inlines and macro's needed some cleanup's and fixes:
* change name of macro SKGEMAC_REG to SK_REG to better reflect usage
and fix comments
* ditto for SK_GEXM_REG -> SK_XMAC_REG and SKGEGMA_REG -> SK_GMA_REG
* change skge_gm_ to just gm_ since it is just a local function and long
names look ugly.
* change skge_xm_ to just xm_
* fix xm_write32 to write as two u16's with correct byte order
* fix xm_outaddr to correctly use offset
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Check the link state during b44_open. This closes a 1 HZ window
that existed after b44_open ran but before the b44_timer handler ran,
during which ethtool would report "Link detected: yes" no matter what
the link state actually was.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the tulip driver to suspend and resume properly. It was
originally written by Karsten Keil and then modified by Adam Belay.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/wireless/prism54/isl_38xx.c:131: warning: 'current_time.tv_sec' is used uninitialized in this function
drivers/net/wireless/prism54/isl_38xx.c:131: warning: 'current_time.tv_usec' is used uninitialized in this function
Signed-off-by: Olaf Hering <olh@suse.de>
Jeff,
Just incase this got lost in the recent netdev mailing list transition
here is a nicer version of Andy's patch for gianfar.
- kumar
* TCP/IP/UDP checksumming and verification
* VLAN tag insertion/extraction
* Larger multicast hash-table
* Padding to align IP headers
Also added:
* msg lvl support
* Some whitespace cleanup
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
The race causes a kernel oops when smc_hardware_send_pkt() tries to
dereference pending_tx_skb which would have been freed from one of the
driver reset paths just after the tx_task tasklet has been scheduled.
This race is possible on SMP but was uncovered by the kernel RT work.
Signed-off-by: Nicolas Pitre <nico@cam.org>
--Boundary-00=_F5lsC5eH1wGW5o9
Content-Type: text/plain;
charset="koi8-r"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
Hi Jeff,
In some messages in via-rhine.c there is a leading space
for no apparent reason. This patch removes it.
--
vda
--Boundary-00=_F5lsC5eH1wGW5o9
Content-Type: text/x-diff;
charset="koi8-r";
name="via-rhine.c.diff"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="via-rhine.c.diff"
Driver version, white space, comments & other
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Included proposals to false late collisions due to H/W latencies
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool set speed/duplex validates parameters for consistency
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
* don't hardcode constant for advertised field
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed the loopback test failure for 82573 based adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Fixed register and loopback test failures with 82573 controllers
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Cleanup debug message printed when Tx Unit hang is detected
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use netdev_priv() to get to netdev->priv - from shemminger@osdl.org
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Use correct WOL settings for 82544 adapters
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
NAPI performance enhancements - Fixed issues with shared interrupts and NAPI resulting in bad performance.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
e100_eeprom_load was called after e100_phy_init causing phy_init
not to use values set in EEPROM - from emann@mrv.com
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Added patch from Eran Mann to fix following e100 MDI/MDI-X issues
* MDI/MDI-X autodetection should never be enabled for 82551ER/QM chips
* enabling this feature based on eeprom settings
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
If the frame has ToDS flag set, mark it by setting skb->pkt_type to
PACKET_OTHERHOST, so that applications unaware of promiscous mode won't get
uplink (STA->AP) packets for STA->STA transmissions relayed by the AP.
Thanks to John Denker and David Gibson for finding the problem and the
solution.
Patch from Pavel Roskin
This patch is to provide support for cs89x0-based network device on
Philips' pnx0105 board.
Signed-off-by: dmitry pervushin <dpervushin@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use ssleep() / msleep_interruptible() [as appropriate]
instead of schedule_timeout() to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use msleep_interruptible() instead of schedule_timeout() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Insert set_current_state() before schedule_timeout() so the
function delays as expected. Without the addition, schedule_timeout()
will return immediately.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Use ssleep() instead of nicedelay()
to guarantee the task delays as expected. Remove the prototype and
definition of nicedelay(). This is a very weird function, because it is
called to sleep in terms of usecs, but always sleeps for 1 second,
completely ignoring the parameter. I have gone ahead and followed suit,
just sleeping for a second in all cases, but maybe someone with the
hardware could tell me if perhaps the paramter *should* matter. Additionally,
nicedelay() is called in TASK_INTERRUPTIBLE state, but doesn't deal with signals
in case these longer delays do not complete, so I believe ssleep() is more
appropriate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
This patch fixes two bugs in the dm9000 network driver:
- Don't read one byte too much in 8bit mode.
- release correct resource
Signed-off-by: Jochen Karrer <j.karrer@lightmaze.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix int vs. pm_message_t confusion in airo. Should change no code.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This is a fix for the interrupt handler in the defxx driver to use
irqreturn_t. Beside the obvious fix of returning a proper status at all,
it actually checks board registers as appropriate for determining if an
interrupt has been recorded in the bus-specific interface logic.
The patch also includes an obvious one-line fix for SET_NETDEV_DEV needed
for the EISA variation, for which I've decided there is no point in sending
separately.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
drivers/net/tulip/dmfe.c: In function `dmfe_parse_srom':
drivers/net/tulip/dmfe.c:1805: warning: passing arg 1 of `__le16_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
drivers/net/tulip/dmfe.c:1817: warning: passing arg 1 of `__le32_to_cpup' from incompatible pointer type
This is basically a guess:
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
The 8129/8130 support is a sub-option that is not visible if the user
hasn't enabled the 8139 support.
Let's make it a bit easier for users to find the driver for their nic.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch contains the follwing cleanups:
- make needlessly global code static
- remove obsolete Emacs settings
Signed-off-by: Adrian Bunk <bunk@stusta.de>
During some performance diagnostics I stumbled on this slightly wasteful
code in pcnet_cs.c which I made the patch included at the bottom for (two
minor comment fixes included).
Improvement:
instead of *always* calculating
lea 0x2c0(%edx),%ebx
and then additionally doing the
mov %edx,0xc0(%ebx)
addition *if we need it*,
we now do the *whole* calculation of
mov %edx,0x380(%ebx)
*only* if we need it.
This even manages to save us a whole 16-byte alignment buffer loss
in this compilation case.
Result: slightly improves IRQ handler performance in both shared and
non-shared IRQ case, which should make my rusty P3/700 a slight bit happier.
Thank you for your support,
Andreas Mohr
old asm result (using gcc 3.3.5):
000015a0 <ei_irq_wrapper>:
15a0: 55 push %ebp
15a1: 89 e5 mov %esp,%ebp
15a3: 53 push %ebx
15a4: 8d 9a c0 02 00 00 lea 0x2c0(%edx),%ebx
15aa: e8 fc ff ff ff call 15ab <ei_irq_wrapper+0xb>
15af: 83 f8 01 cmp $0x1,%eax
15b2: 74 03 je 15b7 <ei_irq_wrapper+0x17>
15b4: 5b pop %ebx
15b5: 5d pop %ebp
15b6: c3 ret
15b7: 31 d2 xor %edx,%edx
15b9: 89 93 c0 00 00 00 mov %edx,0xc0(%ebx)
15bf: eb f3 jmp 15b4 <ei_irq_wrapper+0x14>
15c1: eb 0d jmp 15d0 <ei_watchdog>
15c3: 90 nop
15c4: 90 nop
15c5: 90 nop
15c6: 90 nop
15c7: 90 nop
15c8: 90 nop
15c9: 90 nop
15ca: 90 nop
15cb: 90 nop
15cc: 90 nop
15cd: 90 nop
15ce: 90 nop
15cf: 90 nop
000015d0 <ei_watchdog>:
new asm result:
000015a0 <ei_irq_wrapper>:
15a0: 55 push %ebp
15a1: 89 e5 mov %esp,%ebp
15a3: 53 push %ebx
15a4: 89 d3 mov %edx,%ebx
15a6: e8 fc ff ff ff call 15a7 <ei_irq_wrapper+0x7>
15ab: 83 f8 01 cmp $0x1,%eax
15ae: 74 03 je 15b3 <ei_irq_wrapper+0x13>
15b0: 5b pop %ebx
15b1: 5d pop %ebp
15b2: c3 ret
15b3: 31 d2 xor %edx,%edx
15b5: 89 93 80 03 00 00 mov %edx,0x380(%ebx)
15bb: eb f3 jmp 15b0 <ei_irq_wrapper+0x10>
15bd: 8d 76 00 lea 0x0(%esi),%esi
000015c0 <ei_watchdog>:
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the DMA_{64,32}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Make sure the code compiles with and without ARLAN_ENTRY_EXIT_DEBUGGING.
Only provide parameter descriptions when parameters are defined.
Remove "arlan_"-prefix to shape up built-in parameter names:
arlan.arlan_debug -> arlan.debug
arlan.arlan_EEPROM_bad -> arlan.EEPROM_bad
arlan.arlan_entry_and_exit_debug -> arlan.entry_and_exit_debug
arlan.arlan_entry_debug -> arlan.entry_debug
arlan.arlan_exit_debug -> arlan.exit_debug
Signed-off-by: Magnus Damm <damm@opensource.se>
Use the DMA_32BIT_MASK constant from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask() instead of custom
macros.
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
