Remove duplicate multipliers in clock_ratio table. On 1,4GHz
Nehemiah two frequencies are present twice in table. It isn't
fatal, but with voltage scaling enabled each will be set twice.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Longhaul with voltage scaling enabled works great on Ezra
CPU (Longhaul ver. 2). As long as "conservative" governor is
used. Both "ondemand" and "userspace" can change voltage
from min to max at once. Motherboard unfortunatly turns off
when vid difference is big. Longhaul was printing warning
message, but it is not enough. Now driver will have
"conservative" governor built in and will split bigger
changes to smaller ones.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
During recent acpi-cpufreq changes, writing to PERF_CTL msr
changed from RMW of entire 64 bit to RMW of low 32 bit and clearing of
upper 32 bit. Fix it back to do a proper RMW of the MSR.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Eliminate build warning (sysfs_create_file return value must be checked)
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It is good idea to wait for PCI bus to become idle before
frequency change. Thanks to ACPI it is possible. It makes
sense only when northbridge support is in use because it is
only case in which we can disable arbiter after check if PCI
bus is busy.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Move one line where it should be. After first transition
Longhaul will skip frequency transition if destination
frequency is already set.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Looks like VT8237 has the same bits which VT8235 has.
Poke registers if it is found.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch is removing southbridge support as separate
kind of support. Instead it is used to make other kinds
of support more stable. Also northbridge and ACPI C3
support both will be used if both are available.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Indicate number of processors and cores more cleanly
in startup messages.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Mark Langsdorf points out that the correct define for this
revision bump is 0x80000. Also to save us having to keep
renaming the #define, give it a more meaningful name.
Signed-off-by: Dave Jones <davej@redhat.com>
When the PST tables are broken, powernow-k7 uses ACPI's processor_perflib to
deduce the available frequency multipliers from the _PSS tables.
Upon frequency change, processor_perflib performs some verification on the
frequency (checks that it's within allowable bounds).
powernow-k7 deals with absolute frequencies in KHz, whereas perflib only
deals with MHz values. When performing the above verification, perflib
multiplies the MHz values by 1000 to obtain the KHz value.
We then end up with situations like the following:
- powernow-k7 multiplies the multiplier by the FSB, and obtains a value
such as 1266768 KHz
- perflib belives the same state has frequency of 1266 MHz
- acpi_processor_ppc_notifier calls cpufreq_verify_within_limits to verify
that 1266768 is in the allowable range of 0 to 1266000 (i.e. 1266 * 1000)
- it's not, so that frequency is rejected
- the maximum CPU frequency is not reachable
This patch solves the problem by rounding up the MHz values stored in perflib's
tables. Additionally it corrects a broken URL.
It also fixes http://bugzilla.kernel.org/show_bug.cgi?id=8255 although this
case is a bit different: the frequencies in the _PSS tables are wildly wrong,
but we get better results if we force ACPI to respect the fsb * multiplier
calculations (even though it seems that the multiplier values aren't entirely
correct either).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Adding tabs where spaces currently are.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB cannot run on i386 at this point because i386 uses the page->private and
page->index field of slab pages for the pgd cache.
Make SLUB run on i386 by replacing the pgd slab cache with a quicklist.
Limit the changes as much as possible. Leave the improvised linked list in place
etc etc. This has been working here for a couple of weeks now.
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When trying to load the ipmi_si module on a powerpc with no BMC (baseboard
management controller) the driver failes to load correctly, but doesn't
unregister itself from of_platform. So, on a second modprobe the kernel
crashes. This patch adds the missing unregister call.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a rather obvious error that Patrick found in the setup routines. Need to
set the proper address space in the ACPI case.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On PPC64, we need to include asm/prom.h for function definitions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush the tty flip buffer when the line discipline input queue is flushed,
including the user call tcflush(TCIFLUSH/TCIOFLUSH). This prevents
unexpected stale data after a user application calls tcflush().
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Antonino Ingargiola <tritemio@gmail.com>
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use zero_user_page() instead of open-coding it.
[akpm@linux-foundation.org: kmap-type fixes]
Signed-off-by: Nate Diller <nate.diller@gmail.com>
Acked-by: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable stacktrace filter support for x86-64 for now. Will be enable when we
can get the dwarf2 unwinder back.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Looks like these two are wired up in a wrong way.
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The earlier change to call the bp mtrr init from bugs.c broke
on some configurations due to missing includes. Noticed
by "Avuton Olrich" <avuton@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pm3fb_setup() should only compiled if pm3fb is built statically in the kernel.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new get_irqnr_preamble macro to move the address of the IRQ
controller outside the IRQ handling loop.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This finally adds the PPC_PRPMC2800 Kconfig option, the board setup
code (the setup and reset functions) and the defconfig, to support the
Motorola PrPMC2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively. There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.
The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant. From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly. If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.
Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_cache_coherency() verifies that the cache coherency setting of
the kernel (CONFIG_NOT_COHERENT_CACHE) matches that left by the firmware,
as indicated by coherency-off device tree property.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds PCI bridge support for the Marvell mv64x60 chip.
We also provide the ability to read/write the mv64x60 hotswap
register via sysfs if the hs_reg_valid property is set in the
device tree.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch creates platform_device entries for the Marvell mv64x60
I2C ports, based on information contained in device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
