Support for CN400 northbridge when ACPI C3 isn't available.
Tested on Epia SP13000. Thanks to Robert for testing it.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
On board of Epia SP13000 is 10x133Mhz VIA Nehemiah. It is reported
as 10x200MHz. This patch is fixing this issue.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Support for Core CPUs was broken in two ways in speedstep-lib: for x86_64,
we missed a MSR definition; for both x86_64 and i386, the FSB calculation
was wrong by four (it's a quad-pumped bus). Also increase the accuracy
of the calculation.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Fix the bug in duplicate states elimination in acpi-cpufreq.
Bug: Due to duplicate state elimiation in the loop earlier, the number
of valid_states can be less than perf->state_count, in which case
freq_table was ending up with some garbage/uninitialized entries
in the table.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
From: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
On some systems there could be bits set in the upper half of
the control value provided by the _PSS object. These bits are
only relevant for cpufreq drivers that use IO ports which are not
currently supported by the speedstep-centrino driver. The current
MSR oriented code assumes that upper bits are not set and thus
fails to work correctly when they are. e.g. the control and status
value equality check failed on the IBM x3650 even though the ACPI
spec allows inequality.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
We don't need a temporary variable to get the PCI revision ID.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dave Jones <davej@redhat.com>
There was lots of #ifdef noise in the kernel due to hotcpu_notifier(fn,
prio) not correctly marking 'fn' as used in the !HOTPLUG_CPU case, and thus
generating compiler warnings of unused symbols, hence forcing people to add
#ifdefs.
the compiler can skip truly unused functions just fine:
text data bss dec hex filename
1624412 728710 3674856 6027978 5bfaca vmlinux.before
1624412 728710 3674856 6027978 5bfaca vmlinux.after
[akpm@osdl.org: topology.c fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We do the exact same printk about a dozen lines above
with no intermediate printk's.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Here is a small patch for i386 which adds a cpufeature flag and
detection code for Intel's Branch Trace Store (BTS) feature. This
feature can be found on Intel P4 and Core 2 processors among others.
It can also be used by perfmon.
changelog:
- add CPU_FEATURE_BTS
- add Branch Trace Store detection
signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Make the needlessly global alloc_gdt() static.
(against) pda-percpu-init
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Until not so long ago, there were system log messages pointing to
inconsistent MTRR setup of the video frame buffer caused by the way vesafb
and X worked. While vesafb was fixed meanwhile, I believe fixing it there
only hides a shortcoming in the MTRR code itself, in that that code is not
symmetric with respect to the ordering of attempts to set up two (or more)
regions where one contains the other. In the current shape, it permits
only setting up sub-regions of pre-exisiting ones. The patch below makes
this symmetric.
While working on that I noticed a few more inconsistencies in that code,
namely
- use of 'unsigned int' for sizes in many, but not all places (the patch
is converting this to use 'unsigned long' everywhere, which specifically
might be necessary for x86-64 once a processor supporting more than 44
physical address bits would become available)
- the code to correct inconsistent settings during secondary processor
startup tried (if necessary) to correct, among other things, the value
in IA32_MTRR_DEF_TYPE, however the newly computed value would never get
used (i.e. stored in the respective MSR)
- the generic range validation code checked that the end of the
to-be-added range would be above 1MB; the value checked should have been
the start of the range
- when contained regions are detected, previously this was allowed only
when the old region was uncacheable; this can be symmetric (i.e. the new
region can also be uncacheable) and even further as per Intel's
documentation write-trough and write-back for either region is also
compatible with the respective opposite in the other
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Allow selected bug checks to be skipped by paravirt kernels. The two most
important are the F00F workaround (which is either done by the hypervisor,
or not required), and the 'hlt' instruction check, which can break under
some hypervisors.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Both lhype and Xen want to call the core of the x86 cpu detect code before
calling start_kernel.
(extracted from larger patch)
AK: folded in start_kernel header patch
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the pcurrent field in the PDA to implement the "current" macro. This ends
up compiling down to a single instruction to get the current task.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use the cpu_number in the PDA to implement raw_smp_processor_id. This is a
little simpler than using thread_info, though the cpu field in thread_info
cannot be removed since it is used for things other than getting the current
CPU in common code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch is the meat of the PDA change. This patch makes several related
changes:
1: Most significantly, %gs is now used in the kernel. This means that on
entry, the old value of %gs is saved away, and it is reloaded with
__KERNEL_PDA.
2: entry.S constructs the stack in the shape of struct pt_regs, and this
is passed around the kernel so that the process's saved register
state can be accessed.
Unfortunately struct pt_regs doesn't currently have space for %gs
(or %fs). This patch extends pt_regs to add space for gs (no space
is allocated for %fs, since it won't be used, and it would just
complicate the code in entry.S to work around the space).
3: Because %gs is now saved on the stack like %ds, %es and the integer
registers, there are a number of places where it no longer needs to
be handled specially; namely context switch, and saving/restoring the
register state in a signal context.
4: And since kernel threads run in kernel space and call normal kernel
code, they need to be created with their %gs == __KERNEL_PDA.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
When a CPU is brought up, a PDA and GDT are allocated for it. The GDT's
__KERNEL_PDA entry is pointed to the allocated PDA memory, so that all
references using this segment descriptor will refer to the PDA.
This patch rearranges CPU initialization a bit, so that the GDT/PDA are set up
as early as possible in cpu_init(). Also for secondary CPUs, GDT+PDA are
preallocated and initialized so all the secondary CPU needs to do is set up
the ldt and load %gs. This will be important once smp_processor_id() and
current use the PDA.
In all cases, the PDA is set up in head.S, before a CPU starts running C code,
so the PDA is always available.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Clean up the espfix code:
- Introduced PER_CPU() macro to be used from asm
- Introduced GET_DESC_BASE() macro to be used from asm
- Rewrote the fixup code in asm, as calling a C code with the altered %ss
appeared to be unsafe
- No longer altering the stack from a .fixup section
- 16bit per-cpu stack is no longer used, instead the stack segment base
is patched the way so that the high word of the kernel and user %esp
are the same.
- Added the limit-patching for the espfix segment. (Chuck Ebbert)
[jeremy@goop.org: use the x86 scaling addressing mode rather than shifting]
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Acked-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Here is a patch (used by perfmon2) to detect the presence of the Precise Event
Based Sampling (PEBS) feature for i386. The patch also adds the cpu_has_pebs
macro.
- adds X86_FEATURE_PEBS
- adds cpu_has_pebs to test for X86_FEATURE_PEBS
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Fix checks that failed to realize that values are 4-kB-unit-sized (note the
format strings in this same diff context which *do* realize the unit size,
via appended "000"!). Also fix an incorrect below-1MB area check (as
gathered from Jan Beulich's unapplied patch at
http://www.ussg.iu.edu/hypermail/linux/kernel/0411.1/1378.html ) Update
mtrr_add_page() docu to make 4-kB-sized calculation more obvious.
Given several further items mentioned in Jan's patch mail, all in all MTRR
code seems surprisingly buggy, for a surprisingly long period of time (many
years). Further work/investigation would be useful.
TBD Note that my patch is pretty much UNTESTED, since I can only verify that it
TBD successfully boots my machine, but I cannot test against actual buggy
TBD hardware which would require these (formerly broken) checks. Long -mm
TBD simmering would make sense, especially since these now-working checks might
TBD turn out to have adverse effects on unaffected hardware.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Conflicts:
drivers/ata/libata-scsi.c
include/linux/libata.h
Futher merge of Linus's head and compilation fixups.
Signed-Off-By: David Howells <dhowells@redhat.com>
arch/x86_64/kernel/cpufreq/../../../i386/kernel/cpu/cpufreq/speedstep-lib.c:131: error: 'MSR_FSB_FREQ' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On some systems such as the IBM x3650 there are bits set in the
upper half of the control values provided by the _PSS object.
These bits are only relevant for cpufreq drivers that use IO ports
which are not currently supported by the speedstep-centrino driver.
The current MSR oriented code assumes that upper bits are not set
and thus fails to work correctly when they are. e.g. the control
and status value equality check fails even though the ACPI spec
allows the inequality.
Signed-off-by: Gary Hade <garyh@us.ibm.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Several more Intel CPUs are now capable using the p4-clockmod cpufreq
driver. As it is of limited use most of the time, print a big bold warning
if a better cpufreq driver might be available.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
acpi-cpufreq needs the same patch as the previous speedstep-centrino change.
Additionally, the centrino driver can have its ifdef moved out a little
further to eliminate some more code/variables.
Signed-off-by: Dave Jones <davej@redhat.com>
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c:396: warning: 'sw_any_bug_dmi_table' defined but not used
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
If someone inserts speedstep-smi on a mobile P4, it prevents other cpufreq
modules from loading until it is unloaded.
Signed-off-by: Hiroshi Miura <miura@da-cha.org>
Signed-off-by: Dave Jones <davej@redhat.com>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only):
- using allmodconfig
- making sure the files are compiling without any warning/error due to
new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Enable ondemand governor and acpi-cpufreq to use IA32_APERF and IA32_MPERF MSR
to get active frequency feedback for the last sampling interval. This will
make ondemand take right frequency decisions when hardware coordination of
frequency is going on.
Without APERF/MPERF, ondemand can take wrong decision at times due
to underlying hardware coordination or TM2.
Example:
* CPU 0 and CPU 1 are hardware cooridnated.
* CPU 1 running at highest frequency.
* CPU 0 was running at highest freq. Now ondemand reduces it to
some intermediate frequency based on utilization.
* Due to underlying hardware coordination with other CPU 1, CPU 0 continues to
run at highest frequency (as long as other CPU is at highest).
* When ondemand samples CPU 0 again next time, without actual frequency
feedback from APERF/MPERF, it will think that previous frequency change
was successful and can go to wrong target frequency. This is because it
thinks that utilization it has got this sampling interval is when running at
intermediate frequency, rather than actual highest frequency.
More information about IA32_APERF IA32_MPERF MSR:
Refer to IA-32 Intel® Architecture Software Developer's Manual at
http://developer.intel.com
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Recent speedstep-centrino unification onto acpi-cpufreq patchset broke
cpuinfo_cur_freq interface in /sys/../cpuinfo/, when MSR was used for
transitions. Attached patch fixes that breakage.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Only change the frequency if the state previously set is different
from what we are trying to set. We don't really have to get the current
frequency at this point.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Mark ACPI hooks in speedstep-centrino as deprecated. Change the order in which
speedstep-centrino and acpi-cpufreq (when both are in kernel) will be
added. First driver to be tried is now acpi-cpufreq, followed by
speedstep-centrino.
Add a note in feature-removal-schedule to mark this deprecation.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Add in the support for Intel Enhanced Speedstep - MSR based transitions.
With this change, the ACPI based support in speedstep-centrino can be
deprecated and duplicate code in that driver can be marked for removal.
Much easier to maintain and support this way. This also reduces the
user misconfigurations and questions on which driver is to be used
under which CPUs to support Enhanced Speedstep.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Some clean up and redsign of the driver. Mainly making it easier to add
support for multiple sub-mechanisms of changing frequency. Currently this
driver supports only ACPI SYSTEM_IO address space. With the changes
below it is easier to add support for other address spaces like Intel
Enhanced Speedstep which uses MSR (ACPI FIXED_FEATURE_HARDWARE) to do the
transitions.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patchset has refresh/rebase of a bunch of patches/bugfixes related to
acpi-cpufreq that were sent earlier on this list.
patch 1/8
Patch that fixes a bug in swcoordination code in acpi-cpufreq
patch 2/8 through patch 7/8
Grand unification of ACPI based speedstep-centrino and acpi-cpufreq drivers.
ACPI allows P-state transitions in multiple ways. Like using IO ports or using
processor native method (MSR). Without this patch, IO port based P-state
transitions are handled in acpi-cpufreq driver and MSR based transitions on
Intel CPUs are handled in speedstep-centrino driver. Even though most of the
code in these two drivers should be similar, except for final changing/checking
of frequency (one driver does it using IO port and other does it through
MSR), we have duplicated code in these two drivers. There are also issues
around BIOSes supporting both MSR and IO port and which driver should be
loaded first in standard installations.
The patchset combines functionality of these two driver into acpi-cpufreq
driver. ACPI based functionality in speedstep-centrino is marked deprecated
and will be removed in future. speedstep-centrino will continue to work
on systems that depend on older non-ACPI table based P-state chanes.
* 2/8 - Patch that reorganizes the code in acpi-cpufreq, cleaning it up
a little and making it easier to add MSR support later.
* 3/8 - Pull in the MSR based transition support into acpi-cpufreq.
* 4/8 - Mark speedstep-centrino deprecated. Change the order in Makefile to
load acpi-cpufreq first and speedstep-centrino later, in cases where both
are configured in.
* 5/8 - lindent acpi-cpufreq.c
* 6/8 - Minor change to eliminate the check of current frequency on
notifications. We can use last set frequency instead.
* 7/8 - Make cpufreq->get of acpi_cpufreq work correctly again.
There will be a patch in future that removes ACPI based support in
speedstep-centrino in coming months.
patch 8/8
Add support for IA32_APERF and IA32_MPERF MSR and get the actual frequency
from these MSRs and use it to determine the next frequency target in ondemand
governor
This patch:
There is a bug in software coordination patch in acpi-cpufreq, due to which
frequency will only be set on first CPU of any coordinated group.
Bug identified by Denis, was not recognised earlier as there are no platforms
yet that use software coordination with acpi-cpufreq driver.
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Get rid of warning in the thermal throttling code about not checking
sysfs return values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes a couple of if() BUG(); constructs to
BUG_ON(); so it can be safely optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Jesper Juhl reported that testing the software math-emulation by forcing
"no387" doesn't work on modern CPU's.
The reason was two-fold:
- you also need to pass in "nofxsr" to make sure that we not only don't
touch the old i387 legacy hardware, it also needs to disable the
modern XMM/FXSR sequences
- "nofxsr" didn't actually clear the capability bits immediately,
leaving the early boot sequence still using FXSR until we got to
the identify_cpu() stage.
This fixes the "nofxsr" flag to take effect immediately on the boot CPU.
Debugging by Randy Dunlap
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Please ignore previous message.
This patch is adding support for CPU connected to CLE266
chipset. For older CPU this is only way. For "Powersaver"
processor this way will be used if ACPI C3 isn't supported.
I have tested it. It seems to work exacly like ACPI.
But it is less safe. On CLE266 chipset port 0x22 is
blocking processor access to PCI bus too.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Make the sections proper and get rid of section mismatch warnings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (225 commits)
[PATCH] Don't set calgary iommu as default y
[PATCH] i386/x86-64: New Intel feature flags
[PATCH] x86: Add a cumulative thermal throttle event counter.
[PATCH] i386: Make the jiffies compares use the 64bit safe macros.
[PATCH] x86: Refactor thermal throttle processing
[PATCH] Add 64bit jiffies compares (for use with get_jiffies_64)
[PATCH] Fix unwinder warning in traps.c
[PATCH] x86: Allow disabling early pci scans with pci=noearly or disallowing conf1
[PATCH] x86: Move direct PCI scanning functions out of line
[PATCH] i386/x86-64: Make all early PCI scans dependent on CONFIG_PCI
[PATCH] Don't leak NT bit into next task
[PATCH] i386/x86-64: Work around gcc bug with noreturn functions in unwinder
[PATCH] Fix some broken white space in ia32_signal.c
[PATCH] Initialize argument registers for 32bit signal handlers.
[PATCH] Remove all traces of signal number conversion
[PATCH] Don't synchronize time reading on single core AMD systems
[PATCH] Remove outdated comment in x86-64 mmconfig code
[PATCH] Use string instructions for Core2 copy/clear
[PATCH] x86: - restore i8259A eoi status on resume
[PATCH] i386: Split multi-line printk in oops output.
...
The functions prepare_set and post_set in kernel/cpu/mtrr/generic.c wrap
the spinlock set_atomicity_lock: prepare_set returns with the lock held,
and post_set releases the lock without acquiring it. Add lock annotations
to these two functions so that sparse can check callers for lock pairing,
and so that sparse will not complain about these functions since they
intentionally use locks in this manner.
Signed-off-by: Josh Triplett <josh@freedesktop.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add supplemental SSE3 instructions flag, and Direct Cache Access flag.
As described in "Intel Processor idenfication and the CPUID instruction
AP485 Sept 2006"
AK: also added for x86-64
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The counter is exported to /sys that keeps track of the
number of thermal events, such that the user knows how bad the
thermal problem might be (since the logging to syslog and mcelog
is rate limited).
AK: Fixed cpu hotplug locking
Signed-off-by: Dmitriy Zavin <dmitriyz@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Refactor the event processing (syslog messaging and rate limiting)
into separate file therm_throt.c. This allows consistent reporting
of CPU thermal throttle events.
After ACK'ing the interrupt, if the event is current, the user
(p4.c/mce_intel.c) calls therm_throt_process to log (and rate limit)
the event. If that function returns 1, the user has the option to log
things further (such as to mce_log in x86_64).
AK: minor cleanup
Signed-off-by: Dmitriy Zavin <dmitriyz@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Mark i386-specific cpu cache functions as __cpuinit. They are all
only called from arch/i386/common.c:display_cache_info() that already is
marked as __cpuinit.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Mark i386-specific cpu identification functions as __cpuinit. They are all
only called from arch/i386/common.c:identify_cpu() that already is marked as
__cpuinit.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Mark i386-specific cpu init functions as __cpuinit. They are all
only called from arch/i386/common.c:identify_cpu() that already is marked as
__cpuinit. This patch also removes the empty function init_umc().
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
The different cpu_dev structures are all used from __cpuinit callers what
I can tell. So mark them as __cpuinitdata instead of __initdata. I am a
little bit unsure about arch/i386/common.c:default_cpu, especially when it
comes to the purpose of this_cpu.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
cpu_dev->c_identify is only called from arch/i386/common.c:identify_cpu(), and
this after generic_identify() already has been called. There is no need to call
this function twice and hook it in c_identify - but I may be wrong, please
double check before applying.
This patch also removes generic_identify() from cpu.h to avoid unnecessary
future nesting.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix a very dubious piece of code in
arch/i386/kernel/cpu/common.c:cpu_init(). This clears out %fs and
%gs, but clobbers %eax in the process without telling gcc. It turns
out that gcc happens to be not using %eax at that point anyway so it
doesn't matter much, but it looks like a bomb waiting to go off.
This does end up saving an instruction, because gcc wants %eax==0 for
the set_debugreg()s below.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
sw_any_bug_dmi_table can be used on resume, so it isn't initdata.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Some buggy BIOSes do a "software any" kind of coordination without telling
about it to OS. So, when OS sets frequency on one CPU on these platforms,
it will also impact all the other logical CPUs that are in the same power
domain. Attached patch is a workaround for those buggy BIOSes.
Patch should be a noop on the normal non-buggy platforms.
Applies over previously sent acpi-cpufreq and software coordination
bug fix patch
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Rename option "dont_scale_voltage" to "scale_voltage" because
don't will be default.
Use "pos" for calculating voltage. In this way driver don't need
to know mV value or low level value. Simply min U is one pos and
max U is second pos. All pos between these two are used.
Assume that min U is for min f and max U for max f. For frequency
between min and max calculate pos based on difference between
current frequency and min f.
Values in mobile VRM table changed to values from
C3-M datasheet.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Ignore the return value of early_init_acpi(), as it can give false error
messages. If there is something really wrong, then register_driver will
fail cleanly with EINVAL later.
[ background: modprobe acpi-cpufreq on systems not capable of speed-scaling
started failing with 'invalid argument', where previously it would only
ever -ENODEV
I'm not 100% happy with the solution. It'd be better to handle
failure properly, but this is a low-impact change for 2.6.18
We can always revisit doing this better in .19 --davej.]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some laptops with VIA C3 processor, CLE266 chipset and
AMI BIOS have incorrect latency values in FADT table. These
laptops seems to be C3 capable, but latency values are to
big: 101 for C2 and 1017 for C3. This option will allow
user to skip C3 latency test but not C3 address test. AMI
BIOS is setting C3 address to correct value in DSDT table.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
ACPI C3 works for "Powersaver" processors, so use it only for them.
Older CPU will change frequency on "halt" only. But we can protect transition
in two ways:
- by ACPI PM2 register, there is "bus master arbiter disable" bit.
This isn't tested because VIA mainboards don't have PM2 register,
- by PLE133 PCI/AGP arbiter disable register.
There are two bits in this register. First is "PCI arbiter disable",
second "AGP arbiter disable". This is working on VIA Epia 800 mainboards.
Test on bm_control is more proper because this is true
when PM2 register exist.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Note how any error from acpi_processor_preregister_performance is ignored.
From: bert hubert <bert.hubert@netherlabs.nl>
Signed-off-by: Dave Jones <davej@redhat.com>
This table is only used by Ezra-T CPUs currently, and has values
for some other CPU. Fix them to match the values used by that CPU,
and for now make it clearer by renaming the variable.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This is changing "always true" test to something usefull.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch makes the needlessly global longhaul_walk_callback() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It seems commit 32ee8c3e47 accidentially
reverted cdc9cc1d74, IOW, it reintroduced
the following compile error with CONFIG_PCI=n:
<-- snip -->
...
CC arch/i386/kernel/cpu/cpufreq/gx-suspmod.o
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c: In function ‘gx_detect_chipset’:
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: error: implicit declaration of function ‘pci_match_id’
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: warning: comparison between pointer and integer
make[3]: *** [arch/i386/kernel/cpu/cpufreq/gx-suspmod.o] Error 1
<-- snip -->
This patch therefore re-adds the dependency of X86_GX_SUSPMOD on PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Without this longhaul will always fail when compiled into kernel,
as it needs to initialise after the ACPI processor module.
I lost this when I was splitting patches. Sorry.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
There is no need to worry about local APIC.
There is need to worry about I/O APIC, because I/O APIC
is replacing good old 8259. According to Nehemiah datasheet VIA is
using 3-wire bus to connect local APIC to I/O APIC.
"[...] When IA32_APIC_BASE[11] is set to 0, processor APICs based on the 3-wire APIC
bus cannot be generally re-enabled until a system hardware reset. The 3-wire bus
looses track of arbitration that would be necessary for complete re-enabling. Certain
(local) APIC functionality can be enabled. [...]"
So we must set disable bit for each interrupt in I/O APIC registers.
Same situation as for PIC - we must poke registers direcly.
How to do this? I don't know. So at the moment it is better to fail.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Minimal change necessary for hardware support.
Changes in longhaul.c:
- most important - now C3 state is causing transition,
- code responsible for clearing "bus master" bit removed,
- protect bcr2 transition in the same way as longhaul.
Signed-off-by: Rafa³ Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Use hotplug version of register_cpu_notifier in late init functions.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mce_disabled cannot be __initdata - we access it during APM resume.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make notifier_blocks associated with cpu_notifier as __cpuinitdata.
__cpuinitdata makes sure that the data is init time only unless
CONFIG_HOTPLUG_CPU is defined.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In 2.6.17, there was a problem with cpu_notifiers and XFS. I provided a
band-aid solution to solve that problem. In the process, i undid all the
changes you both were making to ensure that these notifiers were available
only at init time (unless CONFIG_HOTPLUG_CPU is defined).
We deferred the real fix to 2.6.18. Here is a set of patches that fixes the
XFS problem cleanly and makes the cpu notifiers available only at init time
(unless CONFIG_HOTPLUG_CPU is defined).
If CONFIG_HOTPLUG_CPU is defined then cpu notifiers are available at run
time.
This patch reverts the notifier_call changes made in 2.6.17
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 1e9f28fa1e ("[PATCH] sched: new
sched domain for representing multi-core") incorrectly made SCHED_SMT
and some of the structures it uses dependent on SMP.
However, this is wrong, the structures are only defined if X86_HT, so
SCHED_SMT has to depend on that as well.
The patch broke voyager, since it doesn't provide any of the multi-core
or hyperthreading structures.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the phys_core_id and cpu_core_id to cpuinfo_x86 structure. Similar
patch for x86_64 is already accepted by Andi earlier this week.
[akpm@osdl.org: fix warning]
Signed-off-by: Rohit Seth <rohitseth@google.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch fixes two issues:
1. cpu_init is called with interrupt disabled. Allocating gdt table
there isn't good at runtime.
2. gdt table page cause memory leak in CPU hotplug case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
Intel now has support for Architectural Performance Monitoring Counters
( Refer to IA-32 Intel Architecture Software Developer's Manual
http://www.intel.com/design/pentium4/manuals/253669.htm ). This
feature is present starting from Intel Core Duo and Intel Core Solo processors.
What this means is, the performance monitoring counters and some performance
monitoring events are now defined in an architectural way (using cpuid).
And there will be no need to check for family/model etc for these architectural
events.
Below is the patch to use this performance counters in nmi watchdog driver.
Patch handles both i386 and x86-64 kernels.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Intel systems report the cache level data from CPUID 4 in sysfs.
Add a CPUID 4 emulation for AMD CPUs to report the same
information for them. This allows programs to read this
information in a uniform way.
The AMD way to report this is less flexible so some assumptions
are hardcoded (e.g. no L3)
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously the apicid<->coreid split was computed based on the max
number of cores. Now use a new CPUID AMD defined for that. On most
systems right now it should be 0 and the old method will be used.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Treat HW coordination as independent CPUs.
This enables per-cpu monintoring of P-states
http://bugzilla.kernel.org/show_bug.cgi?id=5737
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert a few stragglers over to for_each_possible_cpu(), remove
for_each_cpu().
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (65 commits)
ACPI: suppress power button event on S3 resume
ACPI: resolve merge conflict between sem2mutex and processor_perflib.c
ACPI: use for_each_possible_cpu() instead of for_each_cpu()
ACPI: delete newly added debugging macros in processor_perflib.c
ACPI: UP build fix for bugzilla-5737
Enable P-state software coordination via _PDC
P-state software coordination for speedstep-centrino
P-state software coordination for acpi-cpufreq
P-state software coordination for ACPI core
ACPI: create acpi_thermal_resume()
ACPI: create acpi_fan_suspend()/acpi_fan_resume()
ACPI: pass pm_message_t from acpi_device_suspend() to root_suspend()
ACPI: create acpi_device_suspend()/acpi_device_resume()
ACPI: replace spin_lock_irq with mutex for ec poll mode
ACPI: Allow a WAN module enable/disable on a Thinkpad X60.
sem2mutex: acpi, acpi_link_lock
ACPI: delete unused acpi_bus_drivers_lock
sem2mutex: drivers/acpi/processor_perflib.c
ACPI add ia64 exports to build acpi_memhotplug as a module
ACPI: asus_acpi_init(): propagate correct return value
...
Manual resolve of conflicts in:
arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.c
arch/i386/kernel/cpu/cpufreq/speedstep-centrino.c
include/acpi/processor.h
New CPU flags for next generation of crypto engine as found in VIA C7
processors.
Signed-off-by: Michal Ludvig <michal@logix.cz>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PCI code was outside of CONFIG_PCI, add __initdata at cyrix_55x0 (since
accessed within __init function only).
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only drm, framebuffer, mtrr parts + misc files here and there.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I haven't really maintained this driver for a while, and I'm not
keeping up with the latest in Intel power management. I get a steady
stream of mail which I don't really do anything useful with; the
cpufreq list seems like a better destination, unless someone wants to
get the mail directly.
Also clean up a couple of ancient comments which don't really apply
anymore (as far as I know, nobody has ever damaged a CPU with this
driver).
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The fid/vid masks for parts using the extended parts are slightly incorrect and can result in
incorrect fid/vid codes being applied. No instances of this problem have been reported in
the field but it could be a problem with future parts.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch clarifies the meaning of the cpu_family if
statements in the hw pstate driver patch for powernow-k8
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Sets minimum PLL divider to 2.
No negative impact when tested with two nForce2 based boards.
Alexander Choporov reported (06/01/06) that xdiv = 1 does not work on his
Abit NF7S2. Although there shouldn't be much cases that lead to xdiv = 1.
(Updates also the (C) year)
Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Even though powernow-k7 doesn't work in SMP environments,
it can work on an SMP configured kernel if there's only
one CPU present, however recalibrate_cpu_khz was returning
-EINVAL on such kernels, so we failed to init the cpufreq driver.
Signed-off-by: Dave Jones <davej@redhat.com>
Remove KERN_* suffixes from some Centrino cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove KERN_* suffixes from some NForce2 cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Forthcoming AMD products will use a different algorithm for transitioning
pstates than the current generation Opteron products do. The attached
patch allows the powernow-k8 driver to work with those products.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This prevents annoying messages being printed when it gets
loaded on a machine that doesn't have support scaling via ACPI.
Signed-off-by: Dave Jones <davej@redhat.com>
This shouldn't have actually caused any problems
(as we return if we 'corrupt' 'i', but it's still not
very pretty. For the sake of adding another local variable,
this got cleaner.
Signed-off-by: Dave Jones <davej@redhat.com>
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call. It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).
This patch fixes all such usages to _not_ have the notifier_call __init
section.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending. This means the value leak through
context switches and allow processes to observe some x87 instruction
state of other processes.
This was actually documented by AMD, but nobody recognized it as
being different from Intel before.
The fix first adds an optimization: instead of unconditionally
calling FNCLEX after each FXSAVE test if ES is pending and skip
it when not needed. Then do a x87 load from a kernel variable to
clear FOP/FIP/FDP.
This means other processes always will only see a constant value
defined by the kernel in their FP state.
I took some pain to make sure to chose a variable that's already
in L1 during context switch to make the overhead of this low.
Also alternative() is used to patch away the new code on CPUs
who don't need it.
Patch for both i386/x86-64.
The problem was discovered originally by Jan Beulich. Richard
Brunner provided the basic code for the workarounds, with contribution
from Jan.
This is CVE-2006-1056
Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a check-after-use introduced by commit
4211a30349 and spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove a duplicate NULL pointer check introduced by commit
4211a30349
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Dave Jones <davej@redhat.com>
It's not actually needed and would break non power of two number
of cores.
Follows similar earlier x86-64 patch.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This prevents crashes on dual core system when enough ticks are lost.
Replaces earlier patch by me.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpu_online_map doesn't exist if !CONFIG_SMP.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andi's previous fix to initialise powernow_data on all siblings
will not work properly with CPU Hotplug.
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Don't use cpuid.2 to determine cache info if cpuid.4 is supported. The
exception is P4 trace cache. We always use cpuid.2 to get trace cache
under P4.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new sched domain for representing multi-core with shared caches
between cores. Consider a dual package system, each package containing two
cores and with last level cache shared between cores with in a package. If
there are two runnable processes, with this appended patch those two
processes will be scheduled on different packages.
On such systems, with this patch we have observed 8% perf improvement with
specJBB(2 warehouse) benchmark and 35% improvement with CFP2000 rate(with 2
users).
This new domain will come into play only on multi-core systems with shared
caches. On other systems, this sched domain will be removed by domain
degeneration code. This new domain can be also used for implementing power
savings policy (see OLS 2005 CMP kernel scheduler paper for more details..
I will post another patch for power savings policy soon)
Most of the arch/* file changes are for cpu_coregroup_map() implementation.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I got an oops on a dual core system because the lost tick handler
called cpufreq_get() on core 1 and powernow tried to follow
a NULL powernow_data[] pointer there.
Initialize powernow_data for all cores of a CPU.
Cc: Jacob Shin <jacob.shin@amd.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug identified by Linus Torvalds <torvalds@osdl.org>: the `out'
instruction depends upon the state of memory_data[], so we need to tell gcc
that before executing it. (The opcode, not gcc).
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=5553
Thanks to Antonio Ospite <ospite@studenti.unina.it> for testing.
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I screwed up this conversion - we should be iterating across online CPUs, not
possible ones.
Spotted by Joe Perches <joe@perches.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/i386/kernel/cpu/centaur.c: In function `centaur_mcr_insert':
arch/i386/kernel/cpu/centaur.c:33: warning: implicit declaration of function `mtrr_centaur_report_mcr'
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When vendor-specific i386 initialization code is unavailable the kernel
falls back to a default CPU model name. Make that model name reflect the
CPU family instead of an internal vendor index.
Tested on Pentium II (family 6 model 5).
/proc/cpuinfo before:
model name : ff/05
after:
model name : 06/05
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow the x86 "sep" feature to be disabled at bootup. This forces use of the
int80 vsyscall. Mainly for testing or benchmarking the int80 vsyscall code.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
