Some free byte positions at onenand_oob_64 were wrong. This was also
reported by Christian Lehne. 3 byte slots are at 2+16*i and 2 byte
slots at 14+16*i.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Default values for boolean and tristate options can only be 'y', 'm' or 'n'.
This patch removes wrong default for MTD_PCMCIA_ANONYMOUS.
Signed-off-by: Jean-Luc Leger <jean-luc.leger@dspnet.fr.eu.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Oops. Stupid StudlyCaps. Again.
This driver is doubly-deprecated because is was subsumed into doc2000.c
and _also_ we want people to start using the new NAND wrapper for these
devices anyway. But ISTR there was still one person using it because
something didn't work for them. Must chase that up and then I can kill
this.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: add locking to console write function
[SERIAL] Remove unconditional enable of TX irq for console
[SERIAL] 8250: set divisor register correctly for AMD Alchemy SoC uart
[SERIAL] AMD Alchemy UART: claim memory range
[SERIAL] Clean up serial locking when obtaining a reference to a port
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
This lacks hardware ECC support and a few optimisations we're going to
want fairly soon, but it works well enough to mount and use JFFS2.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Addresses for ioremap must be calculated off of pci_resource_start;
we can't directly use the bus address as seen by the HCA. Fix the
code that remaps device memory for FMR access.
Based on patch by Klaus Smolin.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
661FX7MI-S motherboard which uses the SiS 661FX chipset. The patch adds
an entry to mii_chip_info for the transceiver.
The PHY ids were found using the sis900_c_122.diff patch from
http://brownhat.org/sis900.html but that patch didn't solve the problem,
because the PHY at address 1 was already being chosen.
Without my patch, when bursts of packets arrive from other hosts on a
LAN, the interface dropped one roughly 10% of the time, causing
retransmits. There were fifth second pauses in refresh of large xterms,
and it made Netrek suck. I can provide further test data.
Workaround in lieu of patch is to use mii-tool to advertise
100baseTx-HD, then force renegotiation.
I wasn't able to identify the actual transceiver, so the description
field is a guess.
This patch is similar to Artur Skawina's patch:
http://marc.theaimsgroup.com/?l=linux-netdev&m=114297516729079&w=2
I'm not sure, but I wonder if it means the default behaviour should be
changed, so as to better handle future transceivers.
Diff is against 2.6.16.13.
Signed-off-by: James Cameron <james.cameron@hp.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
make sure phy_map entries whose PHY address is masked are initialized
to NULL, given that other code (such as mdiobus_unregister for
instance) assumes that non-NULL phy_map entries are allocated
phy_devices
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Bringing down a port also masks off the status and other IRQ's
needed for device to function due to missing paren's.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This patch corrects the order of the calls to register_chrdev() and
pcmcia_register_driver(). Now udev correctly creates userspace device
files /dev/cmmN and /dev/cmxN respectively.
Based on an earlier patch by Jan Niehusmann <jan@gondor.com>.
Signed-off-by: Harald Welte <laforge@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A race condition exists in mptfc between the thread registering a device
with the fc transport and the scan work generated by the transport.
This race existed prior to the application of the mptfc bug fix patch.
mptfc_register_dev() calls fc_remote_port_add() with the FC_RPORT_ROLE_TARGET
bit set in the rport ids passed to the function. Having this bit set causes
fc_remote_port_add() to schedule a scan of the device.
This scan can execute before mptfc_register_dev() can fill in the dd_data
in the rport structure. When this happens, mptfc_target_alloc() will fail
because dd_data is null.
Attached is a patch which fixes the problem. The patch changes the rport ids
passed to fc_remote_port_add() to not have the TARGET bit set. This prevents
the scan from being scheduled. After mptfc_register_dev() fills in the rport
dd_data field, fc_remote_port_rolechg() is called, changing the role of the
rport to TARGET. Thus, the scan is scheduled after dd_data is filled
in which prevents the failure in mptfc_target_alloc().
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
tg3_run_loopback doesn't check that dev_alloc_skb() returns anything
useful.
Even if dev_alloc_skb() fails to return an skb to us we'll happily go
on and assume it did, so we risk dereferencing a NULL pointer. Much
better to fail gracefully by returning -ENOMEM than crashing here.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a child interface with a non-default P_Key via
/sys/class/net/ibX/delete_child, the interface must be freed with
free_netdev() (rather than kfree() on the private data).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since sir_kthread.c pretty much duplicates the workqueue
functionality, we'd better switch. The SIR fsm has been merged into
sir_dev.c and thus sir_kthread.c is deleted.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal PNP hotplug support for the smsc-ircc2 driver. A modular
driver will be modprobed via hotplug, but still bypasses driver model
probing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the CS5535 errata 111:
When the SMBus controller tries to access a non-existing device, it sets
the NEGACK bit, SMBus I/O offset 01h[4], to 1 after it detects no
acknowledge at the ninth clock. The specification states that the bit
can be cleared by writing a 1 to it, but under certain circumstances it
is possible for this bit to not clear.
Writing a 0 to the bit resets the internal state machine and clears the
issue.
Since all writable bits in ACBST are W1C bits (write-one-to-clear) the
second write doesn't affect any other logic except the buggy NEGACK
state machine. The second write clears an internal register which is
responsible for "overwriting" the NEGACK bit in ACBST.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't pass a string on the stack to request_region. As soon as we
leave the function that stack is gone and the string is lost. Let's
use the same string we identify the i2c_adapter with instead, it's
more simple, more consistent, and just works.
This is the second half of fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scx200_acb driver shouldn't return failure after initialization
if it successfully registered at least one i2c_adapter, else we are
leaking resources. The driver was OK in that respect up to 2.6.16, a
recent change broke it.
This is part of the fix to bug #6445.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix races in in destroying various objects. If a destroy routine
waits for an object to become free by doing
wait_event(&obj->wait, !atomic_read(&obj->refcount));
/* now clean up and destroy the object */
and another place drops a reference to the object by doing
if (atomic_dec_and_test(&obj->refcount))
wake_up(&obj->wait);
then this is susceptible to a race where the wait_event() and final
freeing of the object occur between the atomic_dec_and_test() and the
wake_up(). And this is a use-after-free, since wake_up() will be
called on part of the already-freed object.
Fix this in mthca by replacing the atomic_t refcounts with plain old
integers protected by a spinlock. This makes it possible to do the
decrement of the reference count and the wake_up() so that it appears
as a single atomic operation to the code waiting on the wait queue.
While touching this code, also simplify mthca_cq_clean(): the CQ being
cleaned cannot go away, because it still has a QP attached to it. So
there's no reason to be paranoid and look up the CQ by number; it's
perfectly safe to use the pointer that the callers already have.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a SCSI abort completes, or the command completes successfully, then
the driver must remove the command from its queue of pending
commands. Similarly, if a device reset succeeds, then all commands
queued for the given device must be removed from the queue.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to display local_link_integrity_errors and
excessive_buffer_overrun_errors in
/sys/class/infiniband/<hca>/ports/<n>/counters/
uses the wrong shift to extract the 4 bit values.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds support for ACG Identification Technologies GmbH's HF
Dual ISO Reader (an RFID tag reader) to the ftdi_sio driver's device ID
table. The product ID was supplied by anotonios (anton at goto10 dot
org) on the ftdi-usb-sio-devel list and subsequently verified by myself
(Ian Abbott).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In kernel 2.6.16, if a mounted storage device is removed, an oops happens
because ub supplies an interface device (and kobject) to the block layer,
but neglects to pin it. And apparently, the block layer expects its users
to pin device structures.
The code in ub was broken this way for years. But the bug was exposed only
by 2.6.16 when it started to call block_uevent on close, which traverses
device structures (kobjects actually).
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The choose_configuration() routine contains code the determine the
device's power source, so that configurations requiring external power
can be ruled out if the device is running on bus power. Unfortunately
it turns out that some devices have errors in their config descriptors
and other devices don't like the GET_DEVICE_STATUS request.
Since that information wasn't used for anything else, this patch (as673)
removes the code, leaving only a comment. It fixes bugzilla entry
#6448.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a small regression in USB controller power usage for many
OHCI controllers, notably including every non-PCI version of OHCI: on
those systems, the runtime autosuspend mechanism is no longer enabled.
The change moves to saner defaults. All root hubs are expected to handle
remote wakeup (and hence autosuspend), although drivers for buggy silicon
may override that default.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach "pegasus" to handle a few of the disconnect fault paths
without hundreds of usless syslog messages.
Handle the carrier check workqueue entry even if the driver has
not been opened.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of the way stringify works, using an expression
like 64 * 1024 for UDSL_MAX_BUF_SIZE results in 64 * 1024
turning up in the modinfo output instead of 65536. So use
65536 directly (this was the only way I found of fixing this).
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The maximum possible bandwidth for a speedtouch modem is about 7Mbaud.
You can only get this by using isochronous urbs (enable_isoc=1) and
altsetting 3. With the current default altsetting of 2, the modem
maxes out at about 4Mbaud. So change the default altsetting to 3
when using isochronous urbs. It would be nice to base the altsetting
on the detected line speed, but that's hard given the current design.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A loop on a power-lost resume path used the wrong index.
I suspect khubd has been working around such bugs.
Noticed by Andreas Mohr <andi@rhlx01.fht-esslingen.de>.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A newer board revision changed the type of ethernet phy.
Moreover, this generalizes the way that a phy gets switched
into fiber mode when autodetection is not available.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
We found a new chip setting that we need in order
to make the driver work more reliable.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip
on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting
ei_status.word16.
The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in
8-bit mode -- ensure this too.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
since the au1000 driver already selects the CRC32 routines, simply replace
the internal ether_crc() implementation with the semantically equivalent
one from <linux/crc32.h>
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
It is more efficient not to write the status ring from the
processor and just read the active portion.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Need to make the edge-triggered workaround timer faster to get marginally
better peformance. The test_and_set_bit in schedule_prep() acts as a barrier
already. Make it a module parameter so that laptops who are concerned
about power can set it to 0; and user's stuck with broken BIOS's
can turn the driver into pure polling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Gcc isn't smart enough to know that it can do a modulo
operation with power of 2 constant by doing a mask.
So add macro to do it for us.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Mask for transmit ring status was picking up bits from the
unused sync ring. They were always zero, so far...
Also, make sure to remind self not to make tx ring too big.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The status interrupt flag should be cleared before processing,
not afterwards to avoid race. Need to process in poll routine
even if no new interrupt status. This is a normal occurrence when
more than 64 frames (NAPI weight) are processed in one poll routine.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Taking the cpu hotplug semaphore in a normal events workqueue
is unsafe because other tasks can wait for any workqueues with
it hold. This results in a deadlock.
Move the DBS timer into its own work queue which is not
affected by other work queue flushes to avoid this.
Has been acked by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: Do not overwrite makefile as anohter user
kbuild: drivers/video/logo/ - fix ident glitch
kbuild: fix gen_initramfs_list.sh
kbuild modpost - relax driver data name
kbuild: removing .tmp_versions considered harmful
kbuild: fix modpost segfault for 64bit mipsel kernel
After dwmw2 let me know it ought to be done, I rewrote the physmap map
driver to be a platform driver. I know zilch about the driver model,
so I probably botched it in some way, but I've done some tests on an
ixp23xx board which uses physmap, and it all seems to work.
In order to not break existing physmap users, I've added some compat
code that will instantiate a platform device iff CONFIG_MTD_PHYSMAP_LEN
is defined and != 0. Also, I've changed the default value for
CONFIG_MTD_PHYSMAP_LEN to zero, so that people who inadvertently
compile in physmap (or new, platform-style, users of physmap) don't get
burned.
This works pretty well -- the new physmap driver is a drop-in replacement
for the old one, and works on said ixp23xx board without any code changes
needed. (This should hold as long as users don't touch 'physmap_map'
directly.)
Once all physmap users have been converted to instantiate their own
platform devices, the compat code can go. (Or we decide that we can
change all the in-tree users at the same time, and never merge the
compat code.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use NULL instead of 0 for a null pointer value (sparse warning):
drivers/net/irda/irda-usb.c:1781:30: warning: Using plain integer as NULL pointer
Also, correct timeout argument to use milliseconds instead of jiffies.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/rtc/rtc-sa1100.c: In function `sa1100_rtc_proc':
drivers/rtc/rtc-sa1100.c:298: warning: unsigned int format, long unsigned int arg (arg 3)
and arrange for sa1100_rtc_open() to pass the devid to free_irq()
rather than NULL.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the conditions under which we poke at the APHY registers in
bcm43xx_phy_initg() to avoid a machine check on chips where they don't
exist.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that the bcm34xx driver and the ieee80211
stack do not agree on what channels are possible for 802.11a.
The ieee80211 stack only wants channels between 34 and 165, while
the bcm43xx driver accepts anything from 0 to 200. I made the
bcm43xx driver comply with the ieee80211 stack expectations, by
using the proper constants.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
[mb]: Reduce stack usage by kzalloc-ing ieee80211_geo
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for valid MAC address in SPROM fields instead of relying on
PHY type while setting the MAC address in the networking subsystem,
as some devices have multiple PHYs.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a crash when
iwconfig ethX mode foo
is done before
ifconfig ethX up
or after
ifconfig ethX down
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3490/1: i.MX: move uart resources to board files
[ARM] 3488/1: make icedcc_putc do the right thing
[ARM] 3487/1: IXP4xx: Support non-PCI systems
[ARM] 3486/1: Mark memory as clobbered by the ARM _syscallX() macros
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mmc_request_done should be called at the end of handling a request, not
between the data and initial command parts of the request.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Address the issue of EDAC/BIOS coexistence for the e752x chip-sets.
We have found a problem where the BIOS will start the system with the error
registers (dev0:fun1) hidden and assuming it has exclusive access to them.
The edac driver violates this assumption.
The workaround this patch offers is to honor the hidden-ness as an
indication that it is not safe to use those registers.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates the lpfc driver to revision 8.1.6, which includes
the following changes:
- Fix data corruption in SCSI BUS reset path, due to reusing
the same request structure for each target.
- Change version number to 8.1.6
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a bug fix for mptspi driver, where after a host reset or
resume, we revalidate the negotiation parameters for all devices.
This bug was introduced when the driver was ported to use the spi
transport layer.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A number of small issues are fixed, and added the header file, missed from the
original series. With this, driver should be pretty stable as tested among
both platform-device-driven and "old way" boards. Also added missing GPL
statement , and updated year field on existing ones to reflect
code update.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SCC uart sends a break sequence each time it is stopped with the
CPM_CR_STOP_TX command. That means that each time an application closes the
serial device, a break is transmitted. To fix this, graceful tx stop is
issued for SCC.
Signed-off-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the issues with multiple irqs.
I am resending based on feedback. I decoupled the dma mask for
consistent memory and fixed leak with multiple irq in error path.
Thanks to Manfred for catching the spin lock problem.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Fixes Rhine I cards disclosing fragments of previously transmitted frames
in new transmissions.
Before transmission, any socket buffer (skb) shorter than the ethernet
minimum length of 60 bytes was zero-padded. On Rhine I cards the data can
later be copied into an aligned transmission buffer without copying this
padding. This resulted in the transmission of the frame with the extra
bytes beyond the provided content leaking the previous contents of this
buffer on to the network.
Now zero-padding is repeated in the local aligned buffer if one is used.
Following a suggestion from the via-rhine maintainer, no attempt is made
here to avoid the duplicated effort of padding the skb if it is known that
an aligned buffer will definitely be used. This is to make the change
"obviously correct" and allow it to be applied to a stable kernel if
necessary. There is no change to the flow of control and the changes are
only to the Rhine I code path.
The patch has run on an in-service Rhine-I host without incident. Frames
shorter than 60 bytes are now correctly zero-padded when captured on a
separate host. I see no unusual stats reported by ifconfig, and no unusual
log messages.
Signed-off-by: Craig Brind <craigbrind@gmail.com>
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, Mar 11, Olaf Hering wrote:
> Why is the /sys/class/net/eth0/device symlink not created for the
> mv643xx_eth driver? Does this work for other platform device drivers?
> Seems to work for the ps2 keyboard at least.
The SET_NETDEV_DEV has to be done before a call to register_netdev. With
the new patch below, the device symlink for the platform device was
created. Unfortunately, after the 4 ls commands, the network connection
died. No idea if the box crashed or if something else broke, lost remote
access.
Provide sysfs 'device' in /class/net/ethN Also, set module owner field,
like pcnet32 driver does.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no reason for the PXAMCI debug code to print so many lines - it
causes the kernel buffer to overflow when trying to debug this driver.
Remove some debug messages which are duplicated by core code, and
combine other messages, resulting in fewer characters written to the
kernel log.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always send a stop command at the end of a data transfer. If we avoid
sending the stop command, some cards remain in data transfer mode, and
refuse to accept further read/write commands.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout. We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
x86 SMP breaks as a result of the previous change, we have no real
option other than to add locking to the 8250 console write function.
If an oops is in progress, try to acquire the lock. If we fail to
do so, continue anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: tidy up white space in a few files
IB/ipath: fix label name in interrupt handler
IB/ipath: improve sparse annotation
IB/ipath: simplify IB timer usage
IB/ipath: simplify RC send posting
IB/ipath: prevent hardware from being accessed during reset
IB/ipath: fix verbs registration
IB/ipath: change handling of PIO buffers
IB/ipath: iterate over correct number of ports during reset
IB/ipath: set up 32-bit DMA mask if 64-bit setup fails
IB/ipath: fix race with exposing reset file
IB/mthca: Fix offset in query_gid method
Fix genrtc's read() routine for 64-bit platforms. Current gen_rtc_read()
stores 64bit integer and returns 8 even if an user tried to read a 32bit
integer.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make rtc-dev work well on 64-bit platforms with 32-bit userland. On those
platforms, users might try to read 32-bit integer value. This patch make
rtc-dev's read() work well for both "int" and "long" size. This tweak is came
from genrtc driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Paulo Marques <pmarques@grupopie.com> MAX_IPD_TIME is by
a factor of ten too small. Since this means that we allow ten times more
IPDs in the intended time frame this could result in a cpu check stop of a
physical cpu.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently loading the ioc3 as a module will cause the ports to be numbered
in reverse order. This mod maintains the proper order of cards for port
numbering.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When retrying a failed BIO_RW_BARRIER request, we need to keep the reference
in ->nr_pending over the whole retry. Currently, we only hold the reference
if the failed request is the *last* one to finish - which is silly, because it
would normally be the first to finish.
So move the rdev_dec_pending call up into the didn't-fail branch. As the rdev
isn't used in the later code, calling rdev_dec_pending earlier doesn't hurt.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the test for 'do barrier work' down a bit so that if the first write to a
raid1 is a BIO_RW_BARRIER write, the checking done by superblock writes will
cause the right thing to happen.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because that is what you get if a BIO_RW_BARRIER isn't supported!
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to hold a reference to rdevs while reading and writing to attempt to
correct read errors. This reference must be taken under an rcu lock.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should add to the counter for the rdev *after* checking if the rdev is
NULL!!!
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
