There's no need to setup the frame pointer again in
call_handle_tlbmiss. The frame pointer will already have been setup in
handle_interrupt.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Unfortunately, due to poor DWARF info in current toolchains, unwinding
through interrutps cannot be done reliably. The problem is that the
DWARF info for function epilogues is wrong.
Take this standard epilogue sequence,
80003cc4: e3 6f mov r14,r15
80003cc6: 26 4f lds.l @r15+,pr
80003cc8: f6 6e mov.l @r15+,r14
<---- interrupt here
80003cca: f6 6b mov.l @r15+,r11
80003ccc: f6 6a mov.l @r15+,r10
80003cce: f6 69 mov.l @r15+,r9
80003cd0: 0b 00 rts
If we take an interrupt at the highlighted point, the DWARF info will
bogusly claim that the return address can be found at some offset from
the frame pointer, even though the frame pointer was just restored. The
worst part is if the unwinder finds a text address at the bogus stack
address - unwinding will continue, for a bit, until it finally comes
across an unexpected address on the stack and blows up.
The only solution is to stop unwinding once we've calculated the
function that was executing when the interrupt occurred. This PC can be
easily calculated from pt_regs->pc.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In order to allow the DWARF unwinder to unwind through exceptions we
need to setup the frame pointer register (r14).
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The address that ret_from_exception and ret_from_irq will return to is
found in the stack slot for SPC, not PR. This error was causing the
DWARF unwinder to pick up the wrong return address on the stack and then
unwind using the unwind tables for the wrong function.
While I'm here I might as well add CFI annotations for the other
registers since they could be useful when unwinding.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
'flush_old_exec()' is the point of no return when doing an execve(), and
it is pretty badly misnamed. It doesn't just flush the old executable
environment, it also starts up the new one.
Which is very inconvenient for things like setting up the new
personality, because we want the new personality to affect the starting
of the new environment, but at the same time we do _not_ want the new
personality to take effect if flushing the old one fails.
As a result, the x86-64 '32-bit' personality is actually done using this
insane "I'm going to change the ABI, but I haven't done it yet" bit
(TIF_ABI_PENDING), with SET_PERSONALITY() not actually setting the
personality, but just the "pending" bit, so that "flush_thread()" can do
the actual personality magic.
This patch in no way changes any of that insanity, but it does split the
'flush_old_exec()' function up into a preparatory part that can fail
(still called flush_old_exec()), and a new part that will actually set
up the new exec environment (setup_new_exec()). All callers are changed
to trivially comply with the new world order.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sh64 on the other hand provides both direct broken out syscalls as well
as socketcall access. As there are binaries that use both socketcall has
to stay around. The current ABI prefers direct syscalls.
It was pointed out that when sys_recvmmsg was added in, sys_accept4 was
overlooked. This takes care of wiring it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh32 at the moment only uses sys_socketcall to reach these, so unwire
recvmmsg for now. While we're at it, add it to the ignore list, as per
the s390 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We don't actually require this in the cpu_relax() polling case, so just
cuddle these around the sleeping version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
After the recent FPU optimisation commit the signature of save_fpu()
changed. "regs" wasn't used in the implementation of save_fpu() anyway.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now when the sh-sci driver can do early serial output,
get rid of the old duplicated code. This patch is V2 and
removes support for "earlyprintk=serial" together with
the following kconfig options:
CONFIG_EARLY_SCIF_CONSOLE
CONFIG_EARLY_SCIF_CONSOLE_PORT
CONFIG_EARLY_PRINTK
With this patch applied "earlyprintk=" support is always
built-in the SuperH kernel. For this to work the serial
driver must have early platform support and in the case
of sh-sci the serial console needs to be enabled:
CONFIG_SERIAL_SH_SCI_CONSOLE=y
So after enabling the SuperH SCI console kconfig option
you also need to point out port using the kernel command
line: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Remember that clocks may be disabled by the boot loader
so you may have to do some board specific static clock
setup before earlyprintk will work on your platform.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh5 scif serial port platform
data from a shared platform device to one platform
device per port. Also, move the serial port to the list
of early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
All sh4a except SuperH Mobile processors are modified by
this patch.
While at it, sh7757 gets early platform device support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Only sh4a SuperH Mobile processors are modified by this
patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
While at it, get rid of the R2D ifdef in the processor
code and adjust the defconfigs to use ttySC1.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh3 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh2a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh2 scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Presently there are a couple of paths in to the alignment handler, where
only the address error path presently quiets the notificiation messages
based on the configuration settings. We carry over the notification level
tests to the default alignment handler itself incase so that they behave
uniformly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
New helper - sys_mmap_pgoff(); switch syscalls to using it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The stub already existed in the _64 syscall table, but was lacking a
__NR_recvmmsg definition, while it was absent entirely for _32 variants.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
The macro container_of from kernel.h performs the same
pointer arithmetic operation.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression mptr;
expression member;
@@
- (void *)((char *)mptr - offsetof(T, member))
+ container_of(mptr, T, member)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Now that associative cache writes are no longer needed by the SH-4/SH-4A
cache flush code, associative write support can be explicitly disabled
for all SH-4A parts. This makes any associative write throw an exception,
as this behaviour can not be assumed to exist on future parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Runtime PM code for SuperH Mobile
to allow drivers to have NULL as pm or callback value.
With this in place there is no need for no-op functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This file breaks out the SuperH PFC code from
arch/sh/kernel/gpio.c + arch/sh/include/asm/gpio.h
to drivers/sh/pfc.c + include/linux/sh_pfc.h.
Similar to the INTC stuff. The non-SuperH specific
file location makes it possible to share the code
between multiple architectures.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7724 code to save and restore CPG state during
R-standby. Only CPG registers IRDACLKCR and SPUCLKCR
require software save and restore.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A number of small optimisations to FPU handling, in particular:
- move the task USEDFPU flag from the thread_info flags field (which
is accessed asynchronously to the thread) to a new status field,
which is only accessed by the thread itself. This allows locking to
be removed in most cases, or can be reduced to a preempt_lock().
This mimics the i386 behaviour.
- move the modification of regs->sr and thread_info->status flags out
of save_fpu() to __unlazy_fpu(). This gives the compiler a better
chance to optimise things, as well as making save_fpu() symmetrical
with restore_fpu() and init_fpu().
- implement prepare_to_copy(), so that when creating a thread, we can
unlazy the FPU prior to copying the thread data structures.
Also make sure that the FPU is disabled while in the kernel, in
particular while booting, and for newly created kernel threads,
In a very artificial benchmark, the execution time for 2500000
context switches was reduced from 50 to 45 seconds.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh port of the sLeAZY-fpu feature currently implemented for some architectures
such us i386.
Right now the SH kernel has a 100% lazy fpu behaviour.
This is of course great for applications that have very sporadic or no FPU use.
However for very frequent FPU users... you take an extra trap every context
switch.
The patch below adds a simple heuristic to this code: after 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch.
After 256 switches, this is reset and the 100% lazy behavior is returned.
Tests with LMbench showed no regression.
I saw a little improvement due to the prefetching (~2%).
The tests below also show that, with this sLeazy patch, indeed,
the number of FPU exceptions is reduced.
To test this. I hacked the lat_ctx LMBench to use the FPU a little more.
sLeasy implementation
===========================================
switch_to calls | 79326
sleasy calls | 42577
do_fpu_state_restore calls| 59232
restore_fpu calls | 59032
Exceptions: 0x800 (FPU disabled ): 16604
100% Leazy (default implementation)
===========================================
switch_to calls | 79690
do_fpu_state_restore calls | 53299
restore_fpu calls | 53101
Exceptions: 0x800 (FPU disabled ): 53273
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
