When the i2c-mv64xxx i2c driver is signalled to abort a transaction,
it aborts it immediately by issuing a stop condition on the bus.
This violates the i2c protocol and can cause what appears to be an i2c
bus hang. This patch delays issuing the stop condition until the i2c
device can reasonably expect a stop condition.
Also includes a minor fixup.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
One more supported PCI ID for the i2c-nforce2 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the ibm_iic driver to the HWMON class so it will scan the
bus for connected hardware monitor sensors.
Signed-off-by: Martin Hicks <mort@bork.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The removal of I2C_DF_NOTIFY left some out of date comments in the
code. Drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Given that implementing i2c_driver.command is optional, there is no
point in an empty implementation thereof.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Geng <linux@MichaelGeng.de>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the VIA CENTAUR CPUs to detection table.
Table was updated to treat future Intel x86 CPUs as VRD10.
Stepping field was added, because some VIA CPUs have
different VRM specs across stepping. I changed the vrm type
to u8 because all drivers use u8 anyway.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simplify the way the w83792d driver handles the extra resolution
bits of voltage input channels.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Yuan Mu <Ymu@winbond.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup the w83792d driver a bit:
* Discard unused lock and irrelevant comments inherited from the
w83781d driver.
* Simplify w83792d_{read,write}_value functions.
* Drop useless address test during detection.
* Drop useless bitmasking.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Yuan Mu <Ymu@winbond.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-dev doesn't use the reference counting logic of struct class_device so move
it to the dynamic method. This makes the code paths simpler and the driver
smaller.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
This prevents i2c drivers from messing up and forgetting to set the
module owner of their driver. It also reduces the size of their drivers
by one line :)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the matroxfb driver.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for acorn arch.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers/media/video and usb/media drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for macintosh.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the hwmon drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the miscellaneaous i2c chip drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the core of the i2c drivers: it removes .name and
.owner fields from the struct i2c_device and modify various
functions to use struct device fields instead.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do not limit the usage count of i2c clients to 1. In other words,
change the client usage count behavior from the old I2C_CLIENT_ALLOW_USE
to the old I2C_CLIENT_ALLOW_MULTIPLE_USE. The rationale is that no
driver actually needs the limiting behavior, and the unlimiting
behavior is slightly easier to implement.
Update the documentation to reflect this change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No i2c client uses the I2C_CLIENT_ALLOW_MULTIPLE_USE flag, drop it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The I2C_DF_DUMMY flag is gone since 2.5.70, it's about time to
drop all ifdef'd out references thereto.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Port the vt8231 hardware monitoring driver from lm_sensors CVS to
Linux 2.6.
Signed-off-by: Roger Lucas <roger@planbit.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch adds support for the Barco LPT->DVI I2C adapter to
the i2c-parport driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate of BCD macros.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the VID reading; no cpu0_vid and vrm files created if
the chip is w83627thf and GPIO5 not enabled.
Signed-off-by: Yuan Mu <ymu@winbond.com.tw>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers, hwmon, adm1025 and adm1026: remove deprecated sysfs names.
these names have been listed for removal for six months, time for them to go
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add code to handle case where board firmware does not start the
RTC.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tweaks i2c-i801.c so that the driver always sets the SMBAUXCTL
register (which enables/disables PEC) explicitly before each transaction.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call serio_reconnect() instead of serio_rescan() when detecting that
a new keyboard was plugged in. This should help KVM uses losing custom
keymap settings when switching between boxes.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix mthca_create_eq for when the EQ size is not a power of 2.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modify_qp should check that the physical port number provided
is a legal value.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check error return on call to mthca_dev_lim for Tavor
(as is done for memfree).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add some PCMCIA device IDs for the microdrive found in the Sharp Zaurus
and a different revision of the Socket CF+ Bluetooth card.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
kill the socket_shutdown()/shutdown_socket() confusion by making it
one single function. move cs_socket_put() in there. nicer to read and
smaller:
original:
text data bss dec hex filename
25181 1076 32 26289 66b1 drivers/pcmcia/pcmcia_core.ko
patched:
text data bss dec hex filename
24973 1076 32 26081 65e1 drivers/pcmcia/pcmcia_core.ko
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Export the stored values instead of re-reading everything in the socket
information sysfs files, and make them accessible to all users, not only
to root.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This adds PCMCIA support for both MPC885ADS and MPC866ADS.
This is established not together with FADS, because 885 does not have
io_block_mapping() for BCSR area.
Also, some cleanups done both for 885ADS and MBX.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This fixes misconfiguration that could result in odd work of some old CF
cards.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some PCMCIA sockets have statically mapped memory windows, but dynamically
mapped IO windows. Using the "nonstatic" socket library is inpractical for
them, as they do neither need a resource database (as we can trust the
kernel resource database on m68k and ppc) nor lots of other features of that
library. Let them get a small "iodyn" socket library (105 lines of code)
instead.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Merge the suspend and resume methods for 16-bit PCMCIA cards into the
device model -- for both runtime power management and suspend to ram/disk.
Bugfix in ds.c by Richard Purdie
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Make the bridge specific initialization code config options depending on
CONFIG_EMBEDDED. Config options for TI/EnE, Toshiba, Ricoh and O2Micro are
available. Disabling all of the specific tweaks cuts off more than half
of yenta_socket.ko.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Also return a value if CONFIG_PCMCIA_PROBE is not set.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add a return value to pcmcia_validate_mem. Only if we have enough memory
available to map the CIS, we should proceed in trying to determine information
about the device.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Don't waste cpu time in yenta interrupt handler when the interrupt was for
another device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
I have recently been switching from using 2.4.32 on my trusty
old Sparc Blade 100 to using 2.6.15 . Some of the problems I ran into
were distorted video when the console was active (missing first
character, skipped dots) and when running X windows (colored snow,
stripes, missing pixels). A quick examination of the 2.6 versus 2.4
source for the ATY driver revealed alot of changes.
A closer look at the code/data for the 64GR/XL chip revealed
two minor "typos" that the rewriter(s) of the code made. The first is
a incorrect clock value (230 .vs. 235) and the second is a missing
flag (M64F_SDRAM_MAGIC_PLL). Making both these changes seems to have
fixed my problem. I tend to think the 235 value is the correct one,
as there is a 29.4 Mhz clock crystal close to the video chip and 235.2
(29.4*8) is too close to 235 to make it a coincidence.
The flag for M64F_SDRAM_MAGIC_PLL was dropped during the
changes made by adaplas in file revision 1.72 on the old bitkeeper
repository.
The change relating to the clock rate has been there forever,
at least in the 2.6 tree. I'm not sure where to look for the old 2.5
tree or if anyone cares when it happened.
On SPARC Blades 100's, which use the ATY MACH64GR video chipset, the
clock crystal frequency is 235.2 Mhz, not 230 Mhz. The chipset also
requires the use of M64F_SDRAM_MAGIC_PLL in order to setup the PLL
properly for the DRAM.
Signed-off-by: Luis F. Ortiz <lfo@Polyad.Org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Richard Purdie
The SL-Cxx00 devices have a power control register in SCOOP that is
shared by both CF and MMC/SD card slots. The CF reset code was resetting
this register leading to various lockups as the MMC power was suddenly
lost. This patch handles the CPR register in a more sensitive manner.
It also removes some unneeded collie specific calls as the reset code
handles this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch moves a large chunk of the sharpsl_pm driver to
arch/arm/common so that it can be reused on other devices such as the
SL-5500 (collie). It also abstracts some functions from the core into
the machine and platform specific parts of the driver to aid reuse.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IXP4xx driver bails out on all A0 CPUs, but it should only do
so on IXP42x as IXP46x has functioning HW.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch #if 0's an unused global function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to drivers making their id tables __devinit, we can't allow
userspace to bind or unbind drivers from devices manually through sysfs.
So we only allow this if CONFIG_HOTPLUG is enabled.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: rearrange exports in platform.c
The new way is to specify export right after symbol definition.
Rearrange exports to follow new style to avoid mixing two styles
in one file.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's the patch for modalias support for input classes. It uses
comma-separated numbers, and doesn't describe all the potential keys (no
module currently cares, and that would make the strings huge). The
changes to input.h are to move the definitions needed by file2alias
outside __KERNEL__. I chose not to move those definitions to
mod_devicetable.h, because there are so many that it might break compile
of something else in the kernel.
The rest is fairly straightforward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
CC: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IDE: MODALIAS support for autoloading of ide-cd, ide-disk, ...
Add MODULE_ALIAS to IDE midlayer modules: ide-disk, ide-cd, ide-floppy and
ide-tape, to autoload these modules depending on the probed media type of
the IDE device.
It is used by udev and replaces the former agent shell script of the hotplug
package, which was required to lookup the media type in the proc filesystem.
Using proc was racy, cause the media file is created after the hotplug event
is sent out.
The module autoloading does not take any effect, until something like the
following udev rule is configured:
SUBSYSTEM=="ide", ACTION=="add", ENV{MODALIAS}=="?*", RUN+="/sbin/modprobe $env{MODALIAS}"
The module ide-scsi will not be autoloaded, cause it requires manual
configuration. It can't be, and never was supported for automatic setup in
the hotplug package. Adding a MODULE_ALIAS to ide-scsi for all supported
media types, would just lead to a default blacklist entry anyway.
$ modinfo ide-disk
filename: /lib/modules/2.6.15-rc4-g1b0997f5/kernel/drivers/ide/ide-disk.ko
description: ATA DISK Driver
alias: ide:*m-disk*
license: GPL
...
$ modprobe -vn ide:m-disk
insmod /lib/modules/2.6.15-rc4-g1b0997f5/kernel/drivers/ide/ide-disk.ko
$ cat /sys/bus/ide/devices/0.0/modalias
ide:m-disk
It also adds attributes to the IDE device:
$ tree /sys/bus/ide/devices/0.0/
/sys/bus/ide/devices/0.0/
|-- bus -> ../../../../../../../bus/ide
|-- drivename
|-- media
|-- modalias
|-- power
| |-- state
| `-- wakeup
`-- uevent
$ cat /sys/bus/ide/devices/0.0/{modalias,drivename,media}
ide:m-disk
hda
disk
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are cases in which a device's memory mapped registers overlap
with another device's memory mapped registers. On several PowerPC
devices this occurs for the MDIO bus, whose registers tended to overlap
with one of the ethernet controllers.
By switching from request_resource to insert_resource we can register
the MDIO bus as a proper platform device and not hack around how we
handle its memory mapped registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as604) makes the driver core hold a device's parent's lock
as well as the device's lock during calls to the probe and remove
methods in a driver. This facility is needed by USB device drivers,
owing to the peculiar way USB devices work:
A device provides multiple interfaces, and drivers are bound
to interfaces rather than to devices;
Nevertheless a reset, reset-configuration, suspend, or resume
affects the entire device and requires the caller to hold the
lock for the device, not just a lock for one of the interfaces.
Since a USB driver's probe method is always called with the interface
lock held, the locking order rules (always lock parent before child)
prevent these methods from acquiring the device lock. The solution
provided here is to call all probe and remove methods, for all devices
(not just USB), with the parent lock already acquired.
Although currently only the USB subsystem requires these changes, people
have mentioned in prior discussion that the overhead of acquiring an
extra semaphore in all the prove/remove sequences is not overly large.
Up to now, the USB core has been using its own set of private
semaphores. A followup patch will remove them, relying entirely on the
device semaphores provided by the driver core.
The code paths affected by this patch are:
device_add and device_del: The USB core already holds the parent
lock, so no actual change is needed.
driver_register and driver_unregister: The driver core will now
lock both the parent and the device before probing or removing.
driver_bind and driver_unbind (in sysfs): These routines will
now lock both the parent and the device before binding or
unbinding.
bus_rescan_devices: The helper routine will lock the parent
before probing a device.
I have not tested this patch for conflicts with other subsystems. As
far as I can see, the only possibility of conflict would lie in the
bus_rescan_devices pathway, and it seems pretty remote. Nevertheless,
it would be good for this to get a lot of testing in -mm.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The first of these changes s/hotplug/uevent/ was needed to
compile sn2_defconfig (ia64/sn). The other three files
changed are blind changes of all remaining bus_type.hotplug
references I could find to bus_type.uevent.
This patch attempts to finish similar changes made in the
gregkh-driver-kill-hotplug-word-from-driver-core Nov 22 patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The distinction between hotplug and uevent does not make sense these
days, netlink events are the default.
udev depends entirely on netlink uevents. Only during early boot and
in initramfs, /sbin/hotplug is needed. So merge the two functions and
provide only one interface without all the options.
The netlink layer got a nice generic interface with named slots
recently, which is probably a better facility to plug events for
subsystem specific events.
Also the new poll() interface to /proc/mounts is a nicer way to
notify about changes than sending events through the core.
The uevents should only be used for driver core related requests to
userspace now.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It makes zero sense to have hotplug, but not the netlink
events enabled today. Remove this option and merge the
kobject_uevent.h header into the kobject.h header file.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These days we use udev to manage all kernel events. /proc/sys/kernel/hotplug
will usually be disabled by an init-script. pnpnbios is not integrated with
the driver core and should stay away from the now disabled /sbin/hotplug.
Set the helper to /sbin/phpbios, even when there is probably no current
user of this faciliy. If it's needed, it should definitely get proper driver
core integration instead of forking binaries from the kernel.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thinko: 64 bytes is the minimum SRQ WQE size (not the maximum).
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes the pragma packing in the ip2 driver by popping the previous
setting rather than explicitly assuming that the correct setting is 4.
This also gets around a compiler bug in the FRV compiler when building
allmodconfig.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prevents a compiler warning and uses down_interruptible() instead of down() in
process context.
Signed-off-by: Sam Bishop <sam@bishop.dhs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix usb_find_interface. You cannot case pointers to int and long on
a big-endian 64-bitter without consequences.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I looked at the userspace code which uses the LPIOC_GET_DEVICE_ID ioctl
and I almost went blind. Let's export it in sysfs instead, and just as a
string instead of with a big-endian length at the beginning of it.
This also prints the message about finding the printer _after_ we know
the minor device number it's going to have, rather than reporting all
printers as 'usblp0'.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: David Woodhouse <dwmw2>
David has a G5 with a printer. I am quite surprised that nobody else noticed
this before. Linus has a G5. Hackers hate printing in general, maybe.
We do not use BKL anymore, because one of code paths had a sleeping call,
so we had to use a semaphore. I am sure it's safe to use unlocked_ioctl.
The new ioctls return long and retval is int. It looks completely fine to me.
We never want these extra bits, and the sign extension ought to work right.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
--
Noticed that my zd1201 adapter isn't "seen" by hal and NetworkManager.
The problem seems to be that unlike other network device drivers I
checked, zd1201 does not do a SET_NETDEV_DEV(), which makes it so a
"device" symlink is created under /sys/class/net/wlan0.
With the following patch the device symlink shows up, and now I am
happily using NetworkManager to control the adapter:
$ ls -l /sys/class/net/wlan0
total 0
-r--r--r-- 1 root root 4096 Dec 18 13:42 address
-r--r--r-- 1 root root 4096 Dec 18 13:42 addr_len
-r--r--r-- 1 root root 4096 Dec 18 13:42 broadcast
-r--r--r-- 1 root root 4096 Dec 18 13:42 carrier
lrwxrwxrwx 1 root root 0 Dec 18 13:42 device -> ../../../devices/pci0001:10/0001:10:1b.1/usb4/4-1
-r--r--r-- 1 root root 4096 Dec 18 13:42 features
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fedora users complain that passing "nousbstorage" to the installer causes
the rest of the USB support to disappear. The installer uses kernel command
line as a way to pass options through Syslinux. The problem stems from the
use of strncmp() in obsolete_checksetup().
I used __module_param_call() instead of module_param because I wanted to
preserve the old syntax in grub.conf, and it's the only macro which allows
to remove the prefix.
The fix is tested to accept the option "nousb" correctly now.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Attached patch adds device IDs for the Linksys USB200M Rev 2 device
which uses the AX88772 chipset.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern pointed out there was an ordering issue in unusual_devs.h,
and this patch fixes it.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement command retries and resets in ub. It is advantageous for users
to know if their devices are getting bad. However, failing every I/O
is not practical if you have a external USB enclosure with a hard drive.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove kmalloc() return value casts that we don't need from
drivers/usb/*
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds vendor and product IDs to the ftdi_sio driver's device
ID table for two devices from teratronik.de. The device IDs were
submitted by O. Wlfelschneider of Teratronik Elektronische Systeme
GmbH.
The charset of the patch is latin-1, same as the original files.
Please apply, thanks! (I've tried to avoid a clash with Andrew Morton's
patch to add support for Posiflex PP-7700 printer to the same driver.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This little patch adds recognition of Posiflex PP-7000 retail printer to
ftdo_sio module. The printer uses FT232BM bridge programmed with custom
VID/PID. The patch posted to lkml and sf.net was for 2.6.11.1 kernel,
here is one reworked for 2.6.12.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Summary: Driver for ATI/Philips USB RF remotes
This is a new input driver for ATI/Philips USB RF remotes (eg. ATI
Remote Wonder II).
Signed-off-by: Ville Syrjl <syrjala@sci.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of ARRAY_SIZE. Some trailing whitespaces are also removed.
Patch is compile-tested on i386.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as621) fixes a local variable conflict I accidently
introduced into usb_set_configuration.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugs involving the REPORT LUNS SCSI-3 command are much easier to track
down if usb-storage displays the command's name, rather than "(Unknown
command)".
Signed-off-by: Paul Walmsley <paul@booyaka.com>
Cc: <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another usb-storage subdriver, which supports two fairly
old dual-XD/SmartMedia reader-writers (USB1.1 devices).
This driver was written by Daniel Drake <dsd@gentoo.org> -- he notes
that he wrote this driver without specs, however a vendor-supplied GPL
driver for the previous generation of products ("sma03") did prove to be
quite useful, as did the sddr09 driver which also has to deal with
low-level physical block layout on SmartMedia.
The original patch has been reformed by me, as it clashed with the
libusual patches.
We really need to consolidate some of this common SmartMedia code, and
get together with the MTD guys to share it with them as well.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the third of three patches to prepare the sddr09 subdriver for
conversion to the Sim-SCSI framework. This patch (as596) moves the
computation of the LBA to the start of the read/write routines, so that
addresses completely beyond the end of the device can be detected and
reported differently from transfers that are partially within the
device's capacity.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andries Brouwer <Andries.Brouwer@cwi.nl>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the second of three patches to prepare the sddr09 subdriver for
conversion to the Sim-SCSI framework. This patch (as595) updates the
code to use standard error values for return codes instead of our
special-purpose USB_STOR_TRANSPORT_... codes. The reverse update is
then needed in the transport routine, but with the Sim-SCSI framework
that routine will go away.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andries Brouwer <Andries.Brouwer@cwi.nl>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the first of three patches to prepare the sddr09 subdriver for
conversion to the Sim-SCSI framework. This patch (as594) straightens
out the initialization procedures and headers:
Some ugly code from usb.c was moved into sddr09.c.
Set-up of the private data structures was moved into the
initialization routine.
The connection between the "dpcm" version and the standalone
version was clarified.
A private declaration was moved from a header file into the
subdriver's .c file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andries Brouwer <Andries.Brouwer@cwi.nl>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OneTouch subdriver submits its own interrupt URB for notifications
about button presses. Consequently it needs to know about suspend and
resume events, so it can cancel or restart the URB.
This patch (as593) adds a hook to struct us_data, to be used for
notifying subdrivers about Power Management events, and it implements
the hook in the OneTouch driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Nick Sillik <n.sillik@temple.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern pointed out that (in 2.6 kernel) one successful submission results
in one callback, even for ISO-out transfers. Thus, the silly check can be
removed from usbmon. This reduces the amount of garbage printed in case
of ISO and Interrupt transfers.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as615b) edits a large number of comments in the uhci-hcd code,
mainly removing excess apostrophes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as616) changed the uhci_explen macro in uhci-hcd.h so that
it now accepts the desired length, rather than length - 1 with special
handling for 0. This also fixes a minor bug that would show up only
when a driver submits a 0-length bulk URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
They deal with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minimum data length must be UART_STATE + 1, as data[UART_STATE] is being
accessed for the new line_state. Although PL-2303 hardware is not
expected to send data with exactly UART_STATE length, this keeps it on
the safe side.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device data in ohci-pxa27x is a struct hcd, not a struct ohci_hcd.
This correct the suspend/resume calls to account for this and adds some
code to invalidate the platform data when the module is removed.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
patch below marks various USB tables and variables as const so that they
end up in .rodata section and don't cacheline share with things that get
written to. For the non-array variables it also allows gcc to optimize
more.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as614) makes a small change to the part of the hub driver
responsible for remote wakeup of root hubs. When these wakeups occur
the driver is suspended, and in case the resume fails the driver should
remain suspended -- it shouldn't try to proceed with its normal
processing.
This will hardly ever matter in normal use, but it did crop up while I
was debugging a different problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as613) moves the updates to hcd->state in the dummy_hcd
driver to where they now belong. It also uses the new
HC_FLAG_HW_ACCESSIBLE flag in a way that simulates a real PCI
controller, and it adds checks for attempts to resume the bus while the
controller is suspended or to suspend the controller while the bus is
active.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as612) removes the "volatile" declarations from the
file-storage gadget. It turns out that they aren't needed for anything
much; adding a few memory barriers does a sufficient job.
The patch also removes a wait_queue. Not much point having a queue when
only one task is ever going to be on it!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: don't allocate dma pools for PIO HCDs
hcd_buffer_alloc() and hcd_buffer_free() have a similar dma_mask
check and revert to kmalloc()/kfree(), but hcd_buffer_create()
doesn't check dma_mask and allocates unused dma pools.
Signed-off-by: Chris Humbert <mahadri-kernel@drigon.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some versions of the controller seem to put multiple report packet into a
single urb. also it can happen that a packet is split across multiple urbs.
unpatched you get a jumpy cursor on some screens.
the patch does:
- handle multiple packets per urb
- handle packets split across multiple urb
- check packet type
- cleanups
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a race-condition in usb-serial driver that can be triggered if
a processes does 'port->tty->driver_data = NULL' in serial_close() while
other processes is in kernel-space about to call serial_ioctl() on the
same port.
This happens because a process can open the device while there is
another one closing it.
The patch below fixes that by adding a semaphore to ensure that no
process will open the device while another process is closing it.
Note that we can't use spinlocks here, since serial_open() and
serial_close() can sleep.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Checks if 'port' is NULL before using it in all tty operations, this
can avoid NULL pointer dereferences.
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When going to suspend, there's no point in setting HC state in
host controller driver as USB core takes care of this.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as610) adds a field to struct usb_device to store the device's
port number. This allows us to remove several loops in the hub driver
(searching for a particular device among all the entries in the parent's
array of children).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as609) changes the way we keep track of power budgeting for
USB hubs and devices, and it updates the choose_configuration routine to
take this information into account. (This is something we should have
been doing all along.) A new field in struct usb_device holds the amount
of bus current available from the upstream port, and the usb_hub structure
keeps track of the current available for each downstream port.
Two new rules for configuration selection are added:
Don't select a self-powered configuration when only bus power
is available.
Don't select a configuration requiring more bus power than is
available.
However the first rule is #if-ed out, because I found that the internal
hub in my HP USB keyboard claims that its only configuration is
self-powered. The rule would prevent the configuration from being chosen,
leaving the hub & keyboard unconfigured. Since similar descriptor errors
may turn out to be fairly common, it seemed wise not to include a rule
that would break automatic configuration unnecessarily for such devices.
The second rule may also trigger unnecessarily, although this should be
less common. More likely it will annoy people by sometimes failing to
accept configurations that should never have been chosen in the first
place.
The patch also changes usbcore's reaction when no configuration is
suitable. Instead of raising an error and rejecting the device, now
the core will simply leave the device unconfigured. People can always
work around such problems by installing configurations manually through
sysfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It looks like that the gs_serial module maybe sleep with spinlock in gs_close.
Sometimes, system hang when I remove the gs_serial module.
From: Fengwei Yin <xaityyy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following cleanups:
- make needlessly global functions static
- every file should #include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The earlier USB locking updates didn't touch the suspend/resume
routines. They need updating as well, since now the caller holds the
device semaphore. This patch (as608) makes the necessary changes. It
also adds a line to store the correct power state when a device is
resumed, something which was unaccountably missing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as606b) is an updated version of my earlier patch to
disconnect children from a hub device when the hub driver is unbound.
Thanks to the changes in the driver core locking, we now know that the
entire hub device (and not just the interface) is locked whenever the
hub driver's disconnect method runs. Hence it is safe to disconnect the
child device structures immediately instead of deferring the job.
The earlier version of the patch neglected to disable the hub's ports.
We don't want to forget that; otherwise we'd end up with live devices
using addresses that have been recycled. This update adds the necessary
code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as605) removes the private udev->serialize semaphore,
relying instead on the locking provided by the embedded struct device's
semaphore. The changes are confined to the core, except that the
usb_trylock_device routine now uses the return convention of
down_trylock rather than down_read_trylock (they return opposite values
for no good reason).
A couple of other associated changes are included as well:
Now that we aren't concerned about HCDs that avoid using the
hcd glue layer, usb_disconnect no longer needs to acquire the
usb_bus_lock -- that can be done by usb_remove_hcd where it
belongs.
Devices aren't locked over the same scope of code in
usb_new_device and hub_port_connect_change as they used to be.
This shouldn't cause any trouble.
Along with the preceding driver core patch, this needs a lot of testing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the driver that forgot to set the module owner up. Now we
can remove the unneeded pointer from the usb driver structure. The idea
for how to do this was from Al Viro, who did this for the PCI drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets drivers, like the usb-serial ones, disable the ability to add
ids from sysfs.
The usb-serial drivers are "odd" in that they are really usb-serial bus
drivers, not usb bus drivers, so the dynamic id logic will have to go
into the usb-serial bus core for those drivers to get that ability.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Echo the usb vendor and product id to the "new_id" file in the driver's
sysfs directory, and then that driver will be able to bind to a device
with those ids if it is present.
Example:
echo 0557 2008 > /sys/bus/usb/drivers/foo_driver/new_id
adds the hex values 0557 and 2008 to the device id table for the foo_driver.
Note, usb-serial drivers do not currently work with this capability yet.
usb-storage also might have some oddities.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will make the dynamic-id stuff easier to do, as it will be
self-contained.
No logic was changed at all.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the bias parameter writeable. Writing the parameter does not trigger
a rebind of currently attached storage devices.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a shim driver libusual, which routes devices between
usb-storage and ub according to the common table, based on unusual_devs.h.
The help and example syntax is in Kconfig.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as515b) adds a routine to usbcore to simplify handling of
host controllers that lost power or were reset during suspend/resume.
The new core routine marks all the child devices of the root hub as
NOTATTACHED and tells khubd to disconnect the device structures as soon
as possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent platform_device update has reintroduced into dummy_hcd.c the
dreaded dev->dev syndrome. This harkens back to when an earlier version
of that driver included the unforgettable line:
dev->dev.dev.driver_data = dev;
This patch (as602) renames the platform_device variables to "pdev", in
the hope of reducing confusion.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
adds new module parameter "devid" that points to a string with format
"device_name:vendor_id:device_id:flags". if provided at module load
time, this string is being parsed and a new entry is created in
usb_dev_id[] and pegasus_ids[] so the new device can later be recognized
by the probe routine. this might be helpful for someone who don't
know/wish to build new module/kernel, but want to use his new usb-to-eth
device that is not yet listed in pegasus.h
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
removes all redundant collecting of the return value from
get/set_registers() and suchlike. can't remember who put all of those
some time ago, but they doesn't make any sense to me. where needed only
a few references remained;
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as601) adds a proper reference count to the file-storage
gadget's main data structure, to keep track of references held by child
devices (LUNs in this case). Before this, the driver would wait for
each child to be released before unbinding.
While there's nothing really wrong with that (you can't create a hang by
doing "rmmod g_file_storage </sys/.../lun0/ro" since the open file will
prevent rmmod from running), the code might as well follow the standard
procedures. Besides, this shrinks the size of the structure by a few
words... :-)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This modifies the HCD builds to automatically "-DDEBUG" if
CONFIG_USB_DEBUG is selected. It's just a minor source code cleanup,
guaranteeing consistency.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the ISP116x HCD use the driver model wakeup flags for its
controller, not the flags in the HCD glue (which will be removed).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes UHCI stop using the HCD glue wakeup flags to report whether
the controller can wake the system. The existing code was wrong anyway;
having a PCI PM capability doesn't imply it reports PME# is supported.
I skimmed Intel's ICH7 datasheet and that basically says the wakeup
signaling gets routed only through ACPI registers. (On the other hand,
many VIA chips provide the PCI PM capabilities...) I think that doing
this correctly with UHCI is going to require the ACPI folk to associate
the /proc/acpi/wakeup identifiers (and wakeup enable/disable flags)
with the relevant /sys/devices/pci*/... devices.
From: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the SL811 HCD use the driver model wakeup flags for its
controller, not the flags in the HCD glue (which will be removed).
From: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/host/sl811-hcd.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
On some systems, EHCI seems to be getting IRQs too early during driver
setup ... before the root hub is allocated, in particular, making trouble
for any code chasing down root hub pointers! In this case, it seems to
be safe to just ignore the root hub setting. Thanks to Rafael J. Wysocki
for getting this properly tested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This teaches the EHCI driver to use the new driver model wakeup flags,
replacing the similar ones in the HCD glue. It also adds a workaround
for the current glitch whereby PCI init doesn't init the wakeup flags
from the PCI PM capabilities. (EHCI controllers don't worry about
legacy mode; the PCI PM capability would always do the job.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
More care on loading firmware, take into account fw->size can't be zero.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A driver for USB ADSL modems based on the ADI eagle chipset using the
usb_atm infrastructure.
The managing part was taken from bsd ueagle driver, other parts were
written from scratch.
The driver uses the in-kernel firmware loader :
- to load a first usb firmware when the modem is in pre-firmware state
- to load the dsp firmware that are swapped in host memory.
- to load CMV (configuration and management variables) when the modem
boot. (We can't use options or sysfs for this as there many possible
values. See
https://mail.gna.org/public/eagleusb-dev/2005-04/msg00031.html for a
description of some)
- to load fpga code for 930 chipset.
The device had 4 endpoints :
* 2 for data (use by usbatm). The incoming
endpoint could be iso or bulk. The modem seems buggy and produce lot's
of atm errors when using it in bulk mode for speed > 3Mbps, so iso
endpoint is need for speed > 3Mbps. At the moment iso endpoint need a
patched usbatm library and for this reason is not included in this patch.
* One bulk endpoint for uploading dsp firmware
* One irq endpoint that notices the driver
- if we need to upload a page of the dsp firmware
- an ack for read or write CMV and the value (for the read case).
If order to make the driver cleaner, we design synchronous
(read|write)_cmv :
-send a synchronous control message to the modem
-wait for an ack or a timeout
-return the value if needed.
In order to run these synchronous usb messages we need a kernel thread.
The driver has been tested with sagem fast 800 modems with different
eagle chipset revision and with ADI 930 since April 2005.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the ehci-hcd driver prepares a control URB, it tests for a
zero-length data stage by looking at the transfer_dma value instead of
the transfer_buffer_length. (In fact it does this even for non-control
URBs, which is an additional aspect of the same bug.)
However, under certain circumstances it's possible for transfer_dma to
be 0 while transfer_buffer_length is non-zero. This can happen when a
freshly allocated page (mapped to address 0 and marked Copy-On-Write,
but never written to) is used as the source buffer for an OUT transfer.
This patch (as598) fixes the problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch makes a cleanup of isp116x-hcd. Most of the volume of
the patch comes from 2 sources: moving the code around to get rid of a
few function prototypes and reworking register dumping functions/macros.
Among other things, switched over from using procfs to debugfs.
Cleanup. The following changes were made:
- Rework register dumping code so it can be used for dumping
to both syslog and debugfs.
- Switch from procfs to debugfs..
- Die gracefully on Unrecoverable Error interrupt.
- Fix memory leak in isp116x_urb_enqueue(), if HC happens to
die in a narrow time window.
- Fix a 'sparce' warning (unnecessary cast).
- Report Devices Removable for root hub ports by default
(was Devices Permanently Attached).
- Move bus suspend/resume functions down in code to get rid of
a few function prototypes.
- A number of one-line cleanups.
- Add an entry to MAINTAINERS.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MAINTAINERS | 6
drivers/usb/host/isp116x-hcd.c | 429 ++++++++++++++++-------------------------
drivers/usb/host/isp116x.h | 83 +++++--
3 files changed, 230 insertions(+), 288 deletions(-)
Until now the isp116x-hcd had no support to reinitialize the HC on
resume, if the controller lost its state during suspend. This patch,
generated against your Oct 26 git tree, adds that support. The patch is
basically the same as the one tested by Ivan Kalatchev, who reported the
problem, on 2.6.13.
Please apply,
Support reinitializing the isp116x host controller from scratch on
resume, if the controller has lost its state.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch by David converts the sending queue of the CDC ACM driver
to a queue of URBs. This is needed for quicker devices. Please apply.
Signed-Off-By: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/class/cdc-acm.c | 229 ++++++++++++++++++++++++++++++--------------
drivers/usb/class/cdc-acm.h | 33 +++++-
2 files changed, 185 insertions(+), 77 deletions(-)
Add power management functions for the pxa27x USB OHCI host controller.
This is a totally rewritten version of the patch by Nicolas Pitre and
Todd Poynor which accounts for recent USB changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All call sites for serial8250_handle_port() acquired the port spinlock
and released it afterwards. This is a needless duplication of code.
Move the spinlocking inside serial8250_handle_port().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The function uart_match_port() incorrectly compares the ioremap'd
virtual addresses of ports instead of the physical address to find
duplicate ports for MMIO based UARTs. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've also fixed the sort-ordering comments on this naming convention.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reading the MSR register on 8250-compatible UARTs results in any
modem status interrupts being cleared. To avoid missing any
status changes, arrange for get_mctrl() to read the current
status via check_modem_status(), which will process any pending
state changes for us.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since MMCI currently uses PIO to read data, we have to take steps
to ensure data cache coherency on aliasing CPU caches. Add the
necessary flush_dcache_page() calls.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Stephen Hemminger <shemminger@osdl.org>
is_multicast_ether_addr() accepts broadcast too, so the
is_broadcast_ether_addr() calls are redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_register_simple() is going away, switch to
using platfrom_device_alloc() + platform_device_add(). Also
make sure that wbsd_driver gets unregistered when wbsd_init
fails.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Select a block size for IO based on the read and write block size
combinations, and whether the card supports partial block reads
and/or partial block writes.
If we are able to satisfy block reads but not block writes, mark
the device read only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Turning struct iphdr::tot_len into __be16 added sparse warning.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And actually, with this, the whole pppox layer can basically
be removed and subsumed into pppoe.c, no other pppox sub-protocol
implementation exists and we've had this thing for at least 4
years.
Signed-off-by: David S. Miller <davem@davemloft.net>
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its common enough to to justify that, TCP still can't use it as it has the
prequeueing stuff, still to be made generic in the not so distant future :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to inet6_hash_connect, making it possible to ditch
dccp_v6_hash_connect and share the same code with TCP instead.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming it to inet_hash_connect, making it possible to ditch
dccp_v4_hash_connect and share the same code with TCP instead.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
readpage(), prepare_write(), and commit_write() callers are updated to
understand the special return code AOP_TRUNCATED_PAGE in the style of
writepage() and WRITEPAGE_ACTIVATE. AOP_TRUNCATED_PAGE tells the caller that
the callee has unlocked the page and that the operation should be tried again
with a new page. OCFS2 uses this to detect and work around a lock inversion in
its aop methods. There should be no change in behaviour for methods that don't
return AOP_TRUNCATED_PAGE.
WRITEPAGE_ACTIVATE is also prepended with AOP_ for consistency and they are
made enums so that kerneldoc can be used to document their semantics.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes all references to the bouncing address
rddunlap@osdl.org and one dead web page from the kernel.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Also use the PnP functions to start/stop the devices during the suspend so
that drivers will not have to duplicate this code.
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some G5s still occasionally experience shutdowns due to overtemp
conditions despite the recent fix. After analyzing logs from such
machines, it appears that the overtemp code is a bit too quick at
shutting the machine down when reaching the critical temperature (tmax +
8) and doesn't leave the fan enough time to actually cool it down. This
happens if the temperature of a CPU suddenly rises too high in a very
short period of time, or occasionally on boot (that is the CPUs are
already overtemp by the time the driver loads).
This patches makes the code a bit more relaxed, leaving a few seconds to
the fans to do their job before kicking the machine shutown.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ignore all files generated from *_shipped files, plus a few others.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch fixes a typo introduced by conversion to dynamic input_dev
allocation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo introduced by conversion to dynamic input_dev
allocation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo introduced by conversion to dynamic input_dev
allocation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Erik Hovland
This patch provides two changes. An indent is supplied for an if/else clause so that it is more readable. An acronym is incorrectly typed as UER when it should be IER.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thanks to Roman Zippel for the suggestion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
[ Short explanation: Kconfig uses ternary math: n/m/y, and !m is m ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts the series of commits
67dbb4ea33281ab031a847807ce381
that changed the GART VM start offset. It fixed some machines, but
seems to continually interact badly with some X versions.
Quoth Ben Herrenschmidt:
"So I think at this point, the best is that we keep the old bogus code
that at least is consistent with the bug in the server. I'm working on a
big patch to X that reworks the memory map stuff completely and fixes
those issues on the server side, I'll do a DRM patch matching this X fix
as well so that the memory map is only ever set in one place and with
what I hope is a correct algorithm..."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo introduced by conversion to dynamic input_dev
allocation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__get_unaligned creates a typeof the var its passed, and writes to it,
which on gcc4.1, spits out the following error:
drivers/char/vc_screen.c: In function 'vcs_write':
drivers/char/vc_screen.c:422: error: assignment of read-only variable 'val'
Signed-off-by: Dave Jones <davej@redhat.com>
[ The "right" fix would be to try to fix <asm-generic/unaligned.h>
but that's hard to do with the tools gcc gives us. So this
simpler patch is preferable -- Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Christophe Zimmerman, this explains the slow mouse movement
with 2.6.x kernels.
And checking the 2.4.x drivers/sbus/char/sunmouse.c driver shows we
always used a 5-byte protocol with Sun mice in the past. I have no
idea how the 3-byte thing got into the 2.6.x driver, but it's surely
wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1). Retested. Problem remains fixed.
Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding would work.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As reported by Jules Villard <jvillard@ens-lyon.fr> and some others, the
recent GART aperture start reconfiguration causes problems on some
setups.
What I _think_ might be happening is that the X server is also trying to
muck around with the card memory map and is forcing it back into a wrong
setting that also happens to no longer match what the DRM wants to do
and blows up. There are bugs all over the place in that code (and still
some bugs in the DRM as well anyway).
This patch attempts to avoid that by using the largest of the 2 values,
which I think will cause it to behave as it used to for you and will
still fix the problem with machines that have an aperture size smaller
than the video memory.
Acked-by: Jules Villard <jvillard@ens-lyon.fr>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the checks are scattered all over and this leads
to inconsistencies and even cases where the check is not made.
Based upon a patch from Kris Katterjohn.
Signed-off-by: David S. Miller <davem@davemloft.net>
The oops is characteristic of the underlying device being removed from
visibility before the class device, and sure enough we do device_del()
before transport_unregister() in the scsi_target_reap() routines. I've
no idea why this is suddenly showing up, since the code has been in
there since that function was first invented. However, I've confirmed
this fixes Andrew Vasquez's boot oops.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The COW semantics just do not make any sense especially
with the physically discontiguous I/O mappings possible
here.
Signed-off-by: David S. Miller <davem@davemloft.net>
Two critical bugs were found in forcedeth 0.47:
- TSO doesn't work.
- pci_map_single() for the rx buffers is called with size==0. This bug
is critical, it causes random memory corruptions on systems with an
iommu.
Below is a minimal fix for both bugs, for 2.6.15.
TSO will be fixed properly in the next version. Tested on x86-64.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[patch 1/3] s390: some minor qeth driver fixes
From: Frank Pavlic <pavlic@de.ibm.com>
- let's have just one function for both ,input and output queue
to check qdio errors
- add /proc/s390dbf/qeth_qerr entries for outbound processing
- check removed for layer2 device in qeth_add_multicast_ipv6
- NULL pointer dereference with bonding and VLAN device fixed
- minimum length check for portname fixed
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth_main.c | 42 +++++++++++++++++++++---------------------
qeth_sys.c | 6 +++---
2 files changed, 24 insertions(+), 24 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Andy,
libphy has no license tag. Something like the attached (untested!) patch
is needed. Hopefully such a change finds its way into 2.6.15.
filename: /lib/modules/2.6.15-rc5-3-ppc64/kernel/drivers/net/phy/libphy.ko
vermagic: 2.6.15-rc5-3-ppc64 SMP gcc-4.1
depends:
srcversion: ACC921B5E82701BE1E6F603
drivers/net/phy/phy_device.c | 4 ++++
1 files changed, 4 insertions(+)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add ID for Symbol LA-4123. Reported by Tomas Novak <tap@post.cz>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
orinoco_nortel was broken during conversion to iomem API. Wrong PCI BAR
is used for chipset registers. Reported by Tomas Novak <tap@post.cz>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch prevents libata from incorrectly modifying inquiry
VPD pages and command support data from ATAPI devices. I have tested
the patch with a SATA ATAPI tape drive on an AHCI controller.
Patch is against kernel 2.4.32 with 2.4.32-libata1.patch applied.
Anthony J. Battersby
Cybernetics
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It is possible for hardware to get confused when an oversized frame
is received. In that case, just drop the packet and increment a counter.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't lose multicast addresses when link goes down or ring
parameters change.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't die if we run out of memory on mtu or ring parameter change.
For other admin operations, don't rebuild Rx ring, just restart the PHY.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Also have to handle out of memory condition on resume.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We changed the name of the Kconfig symbols along with
the move to arch/powerpc. This one hunk got lost during
the conversion.
From: Jens.Osterkamp@de.ibm.com
Cc: netdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/s2io.c: In function `s2io_txdl_getskb':
drivers/net/s2io.c:2023: warning: cast from pointer to integer of different size
drivers/net/s2io.c: In function `s2io_open':
drivers/net/s2io.c:3325: warning: long long unsigned int format, u64 arg (arg 3)
drivers/net/s2io.c:3333: warning: long long unsigned int format, u64 arg (arg 3)
drivers/net/s2io.c: In function `s2io_eeprom_test':
drivers/net/s2io.c:4749: warning: long long unsigned int format, long unsigned int arg (arg 3)
drivers/net/s2io.c:4749: warning: long long unsigned int format, u64 arg (arg 4)
drivers/net/s2io.c:4768: warning: long long unsigned int format, long unsigned int arg (arg 3)
drivers/net/s2io.c:4768: warning: long long unsigned int format, u64 arg (arg 4)
I had to update this patch because more warnings have just appeared.
You cannot print a u64 with %l or %ll. You do not know what type the
architecture is using. It must be cast to a type which matches the printf
control string - unsigned long long.
The patch also fixes some overly-long strings. Please try to keep the code
looking neat in an 80-col window.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Ananda Raju <Ananda.Raju@neterion.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If changing ring parameters is unable to allocate memory, we need
to return an error and take the device down.
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5715
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Don't need to keep Yukon-2 related definitions around for Skge
driver that is only for Yukon-1 and Genesis.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
