This allows for proper console unregistration via the VT layer, and updates
the FB layer to use it. This makes debugging new console drivers much easier,
since you can properly clean them up before unloading.
[adaplas]
unregister_framebuffer() is typically called as part of the driver's
module_exit(). Doing so otherwise will freeze the machine as the VT layer is
holding reference counts on fbcon, and fbcon on the driver. With this change,
it allows unregister_framebuffer() to be called safely anywhere as needed.
Additions from the original: If multiple drivers are used by fbcon, and if
one of them unregisters, a driver will take over the consoles vacated by the
outgoing one (via set_con2fb_map). Once only the outgoing driver remains,
then fbcon will unbind from the VT layer (if CONFIG_HW_CONSOLE_UNBINDING is
set to y).
It is important that these drivers implement fb_open() and fb_release()
just to ensure that no other process is using the driver. Likewise, these
drivers _must_ check the return value of unregister_framebuffer().
[akpm@linux-foundation.org: make fbcon_unbind() stub inline]
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow fbcon to select the primary display adapter using the
fb_is_primary_device() arch-specific helper. If a a primary adapter is
detected, fbcon will unbind the old adapter from the VT layer, then rebind
using the new adapter. This requires that bind_/unbind_con_driver() be made
public.
Because this feature may produce unexpected behavior (from the user's POV),
this must be explicitly enabled in Kconfig.
[akpm@linux-foundation.org: export unbind_con_driver]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add function helper, fb_is_primary_device(). Given struct fb_info, it will
return a nonzero value if the device is the primary display.
Currently, only the i386 is supported where the function checks for the
IORESOURCE_ROM_SHADOW flag.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move arch-specific bits of fb_mmap() to their respective subdirectories
[bob.picco@hp.com: efi_range_is_wc is referenced but not declared]
[bunk@stusta.de: fix include/asm-m68k/fb.h]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow root squashing to vary per-pseudoflavor, so that you can (for example)
allow root access only when sufficiently strong security is in use.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We could return some sort of error in the case where someone asks for secinfo
on an export without the secinfo= option set--that'd be no worse than what
we've been doing. But it's not really correct. So, hack up an approximate
secinfo response in that case--it may not be complete, but it'll tell the
client at least one acceptable security flavor.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement the secinfo operation.
(Thanks to Usha Ketineni wrote an earlier version of this support.)
Cc: Usha Ketineni <uketinen@us.ibm.com>
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow readonly access to vary depending on the pseudoflavor, using the flag
passed with each pseudoflavor in the export downcall. The rest of the flags
are ignored for now, though some day we might also allow id squashing to vary
based on the flavor.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the first actual use of the secinfo information by using it to return
nfserr_wrongsec when an export is found that doesn't allow the flavor used on
this request.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want it to be possible for users to restrict exports both by IP address and
by pseudoflavor. The pseudoflavor information has previously been passed
using special auth_domains stored in the rq_client field. After the preceding
patch that stored the pseudoflavor in rq_pflavor, that's now superfluous; so
now we use rq_client for the ip information, as auth_null and auth_unix do.
However, we keep around the special auth_domain in the rq_gssclient field for
backwards compatibility purposes, so we can still do upcalls using the old
"gss/pseudoflavor" auth_domain if upcalls using the unix domain to give us an
appropriate export. This allows us to continue supporting old mountd.
In fact, for this first patch, we always use the "gss/pseudoflavor"
auth_domain (and only it) if it is available; thus rq_client is ignored in the
auth_gss case, and this patch on its own makes no change in behavior; that
will be left to later patches.
Note on idmap: I'm almost tempted to just replace the auth_domain in the idmap
upcall by a dummy value--no version of idmapd has ever used it, and it's
unlikely anyone really wants to perform idmapping differently depending on the
where the client is (they may want to perform *credential* mapping
differently, but that's a different matter--the idmapper just handles id's
used in getattr and setattr). But I'm updating the idmapd code anyway, just
out of general backwards-compatibility paranoia.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the callers of exp_get_by_name(), exp_find(), and exp_parent() into
those that are processing requests and those that are doing other stuff (like
looking up filehandles for mountd).
No change in behavior, just a (fairly pointless, on its own) cleanup.
(Note this has the effect of making nfsd_cross_mnt() pass rqstp->rq_client
instead of exp->ex_client into exp_find_by_name(). However, the two should
have the same value at this point.)
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're passing three arguments to exp_pseudoroot, two of which are just fields
of the svc_rqst. Soon we'll want to pass in a third field as well. So let's
just give up and pass in the whole struct svc_rqst.
Also sneak in some minor style cleanups while we're at it.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We add a list of pseudoflavors to each export downcall, which will be used
both as a list of security flavors allowed on that export, and (in the order
given) as the list of pseudoflavors to return on secinfo calls.
This patch parses the new downcall information and adds it to the export
structure, but doesn't use it for anything yet.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new field to the svc_rqst structure to record the pseudoflavor that the
request was made with. For now we record the pseudoflavor but don't use it
for anything.
Signed-off-by: Andy Adamson <andros@citi.umich.edu>
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One more incremental delegation policy improvement: don't give out a
delegation on a file if conflicting access has previously required that a
delegation be revoked on that file. (In practice we'll forget about the
conflict when the struct nfs4_file is removed on close, so this is of limited
use for now, though it should at least solve a temporary problem with
self-conflicts on write opens from the same client.)
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Our original NFSv4 delegation policy was to give out a read delegation on any
open when it was possible to.
Since the lifetime of a delegation isn't limited to that of an open, a client
may quite reasonably hang on to a delegation as long as it has the inode
cached. This becomes an obvious problem the first time a client's inode cache
approaches the size of the server's total memory.
Our first quick solution was to add a hard-coded limit. This patch makes a
mild incremental improvement by varying that limit according to the server's
total memory size, allowing at most 4 delegations per megabyte of RAM.
My quick back-of-the-envelope calculation finds that in the worst case (where
every delegation is for a different inode), a delegation could take about
1.5K, which would make the worst case usage about 6% of memory. The new limit
works out to be about the same as the old on a 1-gig server.
[akpm@linux-foundation.org: Don't needlessly bloat vmlinux]
[akpm@linux-foundation.org: Make it right for highmem machines]
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It looks like Al Viro gutted this header file five years ago and it hasn't
been touched since.
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NFS4_FHSIZE is measured in bytes, not 4-byte words, so much more space than
necessary is being allocated for struct nfs4_cb_recall.
I should have wondered why this structure was so much larger than it needed to
be!
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both lockd and (in the nfsv4 case) nfsd enforce a "grace period" after reboot,
during which clients may reclaim locks from the previous server instance, but
may not acquire new locks.
Currently the lockd and nfsd enforce grace periods of different lengths. This
may cause problems when we reboot a server with both v2/v3 and v4 clients.
For example, if the lockd grace period is shorter (as is likely the case),
then a v3 client might acquire a new lock that conflicts with a lock already
held (but not yet reclaimed) by a v4 client.
This patch calculates a lease time that lockd and nfsd can both use.
Signed-off-by: Marc Eshel <eshel@almaden.ibm.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently NFSD calls directly into filesystems through the export_operations
structure. I plan to change this interface in various ways in later patches,
and want to avoid the export of the default operations to NFSD, so this patch
adds two simple exportfs_encode_fh/exportfs_decode_fh helpers for NFSD to call
instead of poking into exportfs guts.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the exportfs interface was added the expectation was that filesystems
provide an operation to convert from a file handle to an inode/dentry, but it
kept a backwards compat option that still calls into iget.
Calling into iget from non-filesystem code is very bad, because it gives too
little information to filesystem, and simply crashes if the filesystem doesn't
implement the ->read_inode routine.
Fortunately there are only two filesystems left using this fallback: efs and
jfs. This patch moves a copy of export_iget to each of those to implement the
get_dentry method.
While this is a temporary increase of lines of code in the kernel it allows
for a much cleaner interface and important code restructuring in later
patches.
[akpm@linux-foundation.org: add jfs_get_inode_flags() declaration]
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
currently the export_operation structure and helpers related to it are in
fs.h. fs.h is already far too large and there are very few places needing the
export bits, so split them off into a separate header.
[akpm@linux-foundation.org: fix cifs build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CAPI 2.0 driver uses a semaphore as mutex. Use the mutex API instead of
the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quicc Engine enabled mpc83xx CPU's has a somewhat different HW interface to
the SPI controller. This patch adds a qe_mode knob that sees to that
needed adaptions are performed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CRC7 routines, used for example in MMC over SPI communication.
Kerneldoc updates
[akpm@linux-foundation.org: fix funny mix of const and non-const]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new spi->mode bit: SPI_3WIRE, for chips where the SI and SO signals
are shared (and which are thus only half duplex). Update the LM70 driver
to require support for that hardware mode from the controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor SPI controller driver updates: make the setup() methods reject
spi->mode bits they don't support, by masking aginst the inverse of bits
they *do* support. This insures against misbehavior later when new mode
bits get added.
Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH.
Support for all four SPI clock/transfer modes is routine.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sparse now warns if one compares pointers with integers. However, there are
false positives, like:
fs/filesystems.c:72:2: warning: Using plain integer as NULL pointer
Every time BUG_ON(ptr) is used, ptr is checked against integer zero. Avoid
that and save ~70 false positives from allyesconfig run.
mentioned by Al.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Josh Triplett <josh@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make arguments of timespec_equal() const struct timespec.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KSYM_NAME_LEN is peculiar in that it does not include the space for the
trailing '\0', forcing all users to use KSYM_NAME_LEN + 1 when allocating
buffer. This is nonsense and error-prone. Moreover, when the caller
forgets that it's very likely to subtly bite back by corrupting the stack
because the last position of the buffer is always cleared to zero.
This patch increments KSYM_NAME_LEN by one and updates code accordingly.
* off-by-one bug in asm-powerpc/kprobes.h::kprobe_lookup_name() macro
is fixed.
* Where MODULE_NAME_LEN and KSYM_NAME_LEN were used together,
MODULE_NAME_LEN was treated as if it didn't include space for the
trailing '\0'. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the SB1250 DUART, a dual serial port implementation
included in the Broadcom family of SOCs descending from the SiByte SB1250
MIPS64 chip multiprocessor. It is a new implementation replacing the
old-fashioned driver currently present in the linux-mips.org tree. It
supports all the usual features one would expect from a(n asynchronous)
serial driver, including modem line control (as far as hardware supports it
-- there is edge detection logic missing from the DCD and RI lines and the
driver does not implement polling of these lines at the moment), the serial
console, BREAK transmission and reception, including the magic SysRq. The
receive FIFO threshold is not maintained though.
The driver was tested with a SWARM board which uses a BCM1250 SOC (which is
dual MIPS64 CMP) and has both ports of the single DUART implemented wired
externally. Both were tested. Testing included using the ports as
terminal lines at 1200bps (which is the ports minimum), 115200bps and a
couple of random speeds inbetween. The modem lines were verified to
operate correctly. No testing was performed with a use as a network
interface, like with SLIP or PPP.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CHILD_MAX macro in limits.h should not be there. It claims to be the
limit on processes a user can own, but its value is wrong for that.
There is no constant value, but a variable resource limit (RLIMIT_NPROC).
Nothing in the kernel uses CHILD_MAX.
The proper thing to do according to POSIX is not to define CHILD_MAX at all.
The sysconf (_SC_CHILD_MAX) implementation works by calling getrlimit.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OPEN_MAX macro in limits.h should not be there. It claims to be the
limit on file descriptors in a process, but its value is wrong for that.
There is no constant value, but a variable resource limit (RLIMIT_NOFILE).
Nothing in the kernel uses OPEN_MAX except things that are wrong to do so.
I've submitted other patches to remove those uses.
The proper thing to do according to POSIX is not to define OPEN_MAX at all.
The sysconf (_SC_OPEN_MAX) implementation works by calling getrlimit.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OPEN_MAX constant is an arbitrary number with no useful relation to
anything. Nothing should be using it. SCM_MAX_FD is just an arbitrary
constant and it should be clear that its value is chosen in net/scm.h
and not actually derived from anything else meaningful in the system.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put WARN_ON and fixed all callers of unregister_blkdev(). Now we can make
unregister_blkdev return void.
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a proper prototype for proc_nr_files() in include/linux/fs.h
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Identical implementations of PTRACE_POKEDATA go into generic_ptrace_pokedata()
function.
AFAICS, fix bug on xtensa where successful PTRACE_POKEDATA will nevertheless
return EPERM.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the kernel OOPSed or BUGed then it probably should be considered as
tainted. Thus, all subsequent OOPSes and SysRq dumps will report the
tainted kernel. This saves a lot of time explaining oddities in the
calltraces.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Added parisc patch from Matthew Wilson -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bounce buffer logic is included on systems that do not need it. If a
system does not have zones like ZONE_DMA and ZONE_HIGHMEM that can lead to
the use of bounce buffers then there is no need to reserve memory pools etc
etc. This is true f.e. for SGI Altix.
Also nicifies the Makefile and gets rid of the tricky "and" there.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Detect slab objects being passed to the page oriented functions of the VM.
It is not sufficient to simply return NULL because the functions calling
page_mapping may depend on other items of the page_struct also to be setup
properly. Moreover slab object may not be properly aligned. The page
oriented functions of the VM expect to operate on page aligned, page sized
objects. Operations on object straddling page boundaries may only affect the
objects partially which may lead to surprising results.
It is better to detect eventually remaining uses and eliminate them.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It becomes now easy to support the zeroing allocs with generic inline
functions in slab.h. Provide inline definitions to allow the continued use of
kzalloc, kmem_cache_zalloc etc but remove other definitions of zeroing
functions from the slab allocators and util.c.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add #ifdefs around data structures only needed if debugging is compiled into
SLUB.
Add inlines to small functions to reduce code size.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define ZERO_OR_NULL_PTR macro to be able to remove the checks from the
allocators. Move ZERO_SIZE_PTR related stuff into slab.h.
Make ZERO_SIZE_PTR work for all slab allocators and get rid of the
WARN_ON_ONCE(size == 0) that is still remaining in SLAB.
Make slub return NULL like the other allocators if a too large memory segment
is requested via __kmalloc.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I can never remember what the function to register to receive VM pressure
is called. I have to trace down from __alloc_pages() to find it.
It's called "set_shrinker()", and it needs Your Help.
1) Don't hide struct shrinker. It contains no magic.
2) Don't allocate "struct shrinker". It's not helpful.
3) Call them "register_shrinker" and "unregister_shrinker".
4) Call the function "shrink" not "shrinker".
5) Reduce the 17 lines of waffly comments to 13, but document it properly.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: David Chinner <dgc@sgi.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we are out of memory of a suitable size we enter reclaim. The current
reclaim algorithm targets pages in LRU order, which is great for fairness at
order-0 but highly unsuitable if you desire pages at higher orders. To get
pages of higher order we must shoot down a very high proportion of memory;
>95% in a lot of cases.
This patch set adds a lumpy reclaim algorithm to the allocator. It targets
groups of pages at the specified order anchored at the end of the active and
inactive lists. This encourages groups of pages at the requested orders to
move from active to inactive, and active to free lists. This behaviour is
only triggered out of direct reclaim when higher order pages have been
requested.
This patch set is particularly effective when utilised with an
anti-fragmentation scheme which groups pages of similar reclaimability
together.
This patch set is based on Peter Zijlstra's lumpy reclaim V2 patch which forms
the foundation. Credit to Mel Gorman for sanitity checking.
Mel said:
The patches have an application with hugepage pool resizing.
When lumpy-reclaim is used used with ZONE_MOVABLE, the hugepages pool can
be resized with greater reliability. Testing on a desktop machine with 2GB
of RAM showed that growing the hugepage pool with ZONE_MOVABLE on it's own
was very slow as the success rate was quite low. Without lumpy-reclaim,
each attempt to grow the pool by 100 pages would yield 1 or 2 hugepages.
With lumpy-reclaim, getting 40 to 70 hugepages on each attempt was typical.
[akpm@osdl.org: ia64 pfn_to_nid fixes and loop cleanup]
[bunk@stusta.de: static declarations for internal functions]
[a.p.zijlstra@chello.nl: initial lumpy V2 implementation]
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Bob Picco <bob.picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
