This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's. Thi=
s patch relies on the irq ICH9 patch to pci_ids.h.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change drivers/message/i20 pci driver to simply do a nestable
enable()/disable() instead of checking for it.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes the pci_{enable,disable}_device() functions to work in a
nested basis, so that eg, three calls to enable_device() require three
calls to disable_device().
The reason for this is to simplify PCI drivers for
multi-interface/capability devices. These are devices that cram more
than one interface in a single function. A relevant example of that is
the Wireless [USB] Host Controller Interface (similar to EHCI) [see
http://www.intel.com/technology/comms/wusb/whci.htm].
In these kind of devices, multiple interfaces are accessed through a
single bar and IRQ line. For that, the drivers map only the smallest
area of the bar to access their register banks and use shared IRQ
handlers.
However, because the order at which those drivers load cannot be known
ahead of time, the sequence in which the calls to pci_enable_device()
and pci_disable_device() cannot be predicted. Thus:
1. driverA starts pci_enable_device()
2. driverB starts pci_enable_device()
3. driverA shutdown pci_disable_device()
4. driverB shutdown pci_disable_device()
between steps 3 and 4, driver B would loose access to it's device,
even if it didn't intend to.
By using this modification, the device won't be disabled until all the
callers to enable() have called disable().
This is implemented by replacing 'struct pci_dev->is_enabled' from a
bitfield to an atomic use count. Each caller to enable increments it,
each caller to disable decrements it. When the count increments from 0
to 1, __pci_enable_device() is called to actually enable the
device. When it drops to zero, pci_disable_device() actually does the
disabling.
We keep the backend __pci_enable_device() for pci_default_resume() to
use and also change the sysfs method implementation, so that userspace
enabling/disabling the device doesn't disable it one time too much.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The existing implementation of pci_block_user_cfg_access() was recently
criticised for providing out of date information and for returning errors
on write, which applications won't be expecting.
This reimplementation uses a global wait queue and a bit per device.
I've open-coded prepare_to_wait() / finish_wait() as I could optimise
it significantly by knowing that the pci_lock protected us at all points.
It looked a bit funny to be doing a spin_unlock_irqsave(); schedule(),
so I used spin_lock_irq() for the _user versions of pci_read_config and
pci_write_config. Not carrying a flags pointer around made the code
much less nasty.
Attempts to block an already blocked device hit a BUG() and attempts to
unblock an already unblocked device hit a WARN(). If we need to block
access to a device from userspace, it's because it's unsafe for even
another bit of the kernel to access the device. An attempt to block
a device for a second time means we're about to access the device to
perform some other operation, which could provoke undefined behaviour
from the device.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Adam Belay <abelay@novell.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__pci_register_driver() error path forgot to unwind.
driver_unregister() needs to be called when pci_create_newid_file() failed.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So it looks like pci aer code will call pci_osc_support_set to tell the
firmware about OSC_EXT_PCI_CONFIG_SUPPORT flag. that causes
ctrlset_buf[OSC_SUPPORT_TYPE] to evaluate to true when pciehp calls
pci_osc_control_set() is called (to attempt to use OSC to gain native
pcie control from firmware), regardless of whether or not _OSC was
actually successfully executed. That causes this section of code:
if (ctrlset_buf[OSC_SUPPORT_TYPE] &&
((global_ctrlsets & ctrlset) != ctrlset)) {
return AE_SUPPORT;
}
to be hit.
This patch will reset the OSC_SUPPORT_TYPE field if _OSC fails, and then
would allow pciehp to go ahead and try to run _OSC again.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpiphp_glue_exit() needs to be called to unwind when no slots found.
(It fixes data corruption when reloading acpiphp driver with no such devices)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes invalid usage of list_for_each()
list_for_each (node, &bridge_list) {
bridge = (struct acpiphp_bridge *)node;
...
}
This code works while the member of list node is located at the
head of struct acpiphp_bridge.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support a shadowed ROM when running with an ACPI capable PROM.
Define a new dev.resource flag IORESOURCE_ROM_BIOS_COPY to
describe the case of a BIOS shadowed ROM, which can then
be used to avoid pci_map_rom() making an unneeded call to
pci_enable_rom().
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A few minor changes to the way slot/device fixup is done.
No need to be calling sn_pci_controller_fixup(), as
a root bus cannot be hotplugged.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pSeries is the only architecture left using HAVE_ARCH_PCI_MWI and it's
really inappropriate for its needs. It really wants to disable MWI
altogether. So here are a pair of stub implementations for pci_set_mwi
and pci_clear_mwi.
Also rename pci_generic_prep_mwi to pci_set_cacheline_size since that
better reflects what it does.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The setting of the CACHE_LINE_SIZE register in sparc64's pci
initialisation code isn't quite adequate as the device may have
incompatible requirements. The generic code tests for this, so switch
sparc64 over to using it.
Since sparc64 has different L1 cache line size and PCI cache line size,
it would need to override the generic code like i386 and ia64 do. We
know what the cache line size is at compile time though, so introduce a
new optional constant PCI_CACHE_LINE_BYTES.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Shouldn't PCI-X state be saved/restored? No device really needs this
right now. qla24xx (fc HBA) and mthca (infiniband) don't do suspend,
and sky2 resets its tweaks when links are brought up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move some MSI-X #defines into pci_regs.h so they can be used
outside of drivers/pci.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's not really broken, but people keep running into other problems
caused by it. Re-enable it so that the drivers get stress tested.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to several earlier patches, usb_autosuspend_device() and
usb_autoresume_device() are never called with a second argument other
than 1. This patch (as819) removes the now-redundant argument.
It also consolidates some common code between those two routines,
putting it into a new subroutine called usb_autopm_do_device(). And
it includes a sizable kerneldoc update for the affected functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as818b) simplifies autosuspend processing by keeping track
of the number of unsuspended children of each USB hub. This will
permit us to avoid a good deal of unnecessary work all the time; we
will no longer have to create a bunch of workqueue entries to carry
out autosuspend requests, only to have them fail because one of the
hub's children isn't suspended.
The basic idea is simple. There already is a usage counter in the
usb_device structure for preventing autosuspends. The patch just
increments that counter for every unsuspended child. There's only one
tricky part: When a device disconnects we need to remember whether it
was suspended at the time (leave the counter alone) or not (decrement
the counter).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as817) simplifies the remote-wakeup processing in the hub
driver. Now instead of using a specialized code path, it relies on
the standard USB resume routines. The hub_port_resume() function does
an initial get_port_status() to see whether the port has already
resumed itself (as it does when a remote-wakeup request is sent).
This will slow down handling of other resume events slightly, but not
enough to matter.
The patch also changes the hub_port_status() routine, making it return
an error if a short reply is received.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as816) changes an existing flag in the usb_device
structure to a bitflag, preparing the way for more bitflags to come
in the future.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unlike UHCI, OHCI does not exert any DMA load on the system when no
devices are connected. Consequently there is no advantage to doing
an autostop other than the power savings, so we shouldn't compile the
necessary code unless CONFIG_PM is enabled.
This patch (as820) makes the root-hub suspend and resume routines
conditional on CONFIG_PM. It also prevents autostop from activating
if the device_may_wakeup flag isn't set; some people use this flag to
alert the driver about Resume-Detect bugs in the hardware.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as742b) adds autosuspend/autoresume support to the USB hub
driver. The largest aspect of the change is that we no longer need a
special flag for root hubs that want to be resumed. Now every hub is
autoresumed whenever khubd needs to access it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as738b) fixes numerous problems in the controller/root-hub
suspend/resume/remote-wakeup support in ehci-hcd:
The bus_resume() routine should wake up only the ports that
were suspended by bus_suspend(). Ports that were already
suspended should remain that way.
The interrupt mask is used to detect loss of power in the
bus_resume() routine (if the mask is 0 then power was lost).
However bus_suspend() always sets the mask to 0. Instead the
mask should retain its normal value, with port-change-detect
interrupts disabled if remote wakeup is turned off.
The interrupt mask should be reset to its correct value at the
end of bus_resume() regardless of whether power was lost.
bus_resume() reinitializes the operational registers if power
was lost. However those registers are not in the aux power
well, hence they can lose their values whenever the controller
is put into D3. They should always be reinitialized.
When a port-change interrupt occurs and the root hub is
suspended, the interrupt handler should request a root-hub
resume instead of starting up the controller all by itself.
There's no need for the interrupt handler to request a
root-hub resume every time a suspended port sends a
remote-wakeup request.
The pci_resume() method doesn't need to check for connected
ports when deciding whether or not to reset the controller.
It can make that decision based on whether Vaux power was
maintained.
Even when the controller does not need to be reset,
pci_resume() must undo the effect of pci_suspend() by
re-enabling the interrupt mask.
If power was lost, pci_resume() must not call ehci_run().
At this point the root hub is still supposed to be suspended,
not running. It's enough to rewrite the command register and
set the configured_flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Might speed up some systems. If nothing else, a bad driver should not
take the whole USB subsystem down with it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is an update for Greg K-H's proposed usbfs2:
http://sourceforge.net/mailarchive/message.php?msg_id=19295229
It creates a dynamic major for USB endpoints and fixes
the endpoint minor calculation.
Signed-off-by: Sarah Bailey <saharabeara@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there is an error path in the pegasus driver which can leave
the task in TASK_UNINTERRUPTIBLE. Depending on when it
schedules next, this can be bad.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the latest update for asix.c reverted some endianness fixes. This
reinstates them.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We do already have both the code and a config option, so why not build
this driver? ;-)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use canonical defines for the Apple USB device IDs.
Also add the Geyser IV devices missing in my previous patch.
Signed-off-by: Julien BLACHE <jb@jblache.org>
Acked-by: Dmitry Torokhov <dtor@insightbb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just digging through code and found these needless variable initializations. So here is the patch.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the pxa2xx_udc driver recognize a newer revision of the IXP425 chip.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the DMC TSC-10 and TSC-25 usb touchscreen controllers.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following possible cleanups:
- make the needlessly global ftdi_release_platform_dev() static
- remove the unused usb_ftdi_elan_read_reg()
- proper prototypes for the following functions:
- usb_ftdi_elan_read_pcimem()
- usb_ftdi_elan_write_pcimem()
Note that the misplaced prototypes for the latter ones in
drivers/usb/host/u132-hcd.c were buggy. Depending on the calling
convention of the architecture calling one of them could have turned
your stack into garbage.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global "u132_hcd_wait" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If at some point cypress_init() fails deregister
only the resources that were registered until that point.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain boards seem to like to issue false overcurrent notifications, for
example on ports that don't have anything connected to them. This looks
like a hardware error, at the level of noise to those ports' overcurrent
input signals (or non-debounced VBUS comparators). This surfaces to users
as truly massive amounts of syslog spam from khubd (which is appropriate
for real hardware problems, except for the volume from multiple ports).
Using this new "ignore_oc" flag helps such systems work more sanely, by
preventing such indications from getting to khubd (and spam syslog). The
downside is of course that true overcurrent errors will be masked; they'll
appear as spontaneous disconnects, without the diagnostics that will let
users troubleshoot issues like short circuited cables.
Note that the bulk of these reports seem to be with VIA southbridges, but
I think some were with Intel ones.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI hooks for high speed electrical tests of the root hub ports.
The expectation is that a usermode program actually triggers the test,
making the same control request it would make for an external hub.
Tests for peripheral upstream ports would issue a different request.
In all cases, the hardware needs re-initialization before it could
be used "normally" again (e.g. unplug/replug, rmmod/modprobe).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net2280 driver is too eager to send zero-length packets when
IN tokens are received on ep0. No such packet should be sent (the
driver should NAK) before the gadget driver has queued the proper
response. Otherwise deferred responses are impossible.
This patch (as823) makes net2280 avoid sending ZLPs for IN transfers
on ep0 until a response has been submitted, and avoids stalling when an
OUT packet is received before a request has been submitted for an OUT
transfer on ep0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Possible memleak fix on error path. The changes:
- out_kfree2 and out_free_urb replaced
- missing scsi_host_put() added
Here it goes:
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mass storage device from Digitech designed for Flash Cards, as found
on (for example) the GNX4 device has issues with residue, similar to the
bug report at http://kerneltrap.org/node/6297. This patch adds the
faulty storage device to unusual_devs.h, this not only reduces the noise
in dmesg but also increases the transfer speeds by a factor of 7x for me
(89kB/s -> 637kB/s).
T: Bus=02 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1210 ProdID=0003 Rev= 1.00
S: Manufacturer=DigiTech HMG
S: Product=DigiTech Mass Storage
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Signed-off-by: Jaco Kroon <jaco@kroon.co.za>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as821) fixes a compiler warning when CONFIG_PM isn't on
("usb_autosuspend_work" defined but not used).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
> 2006/11/11, Adrian Bunk <bunk@stusta.de>:
> > The Coverity checker spotted the following in
> > drivers/usb/serial/aircable.c:
> >
> > <-- snip -->
> >
> > ...
> > static void aircable_read(void *params)
> > {
> > ...
Hi everyone,
Sorry for the long time response but here is the patch, I think this way should
work, if anyone has any suggestion let me know. What I do now is, in case I
don't have the tty available I reschedule the work, I have tried it and it
works with no problem, I even tried removing the device, and didn't find
anything strange.
Signed-off-by: Naranjo Manuel <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the other root-hub suspend or resume log messages, in ohci-hcd or
any of the other host controller drivers, use the debug priority
level. This patch (as815) makes the one single exception behave like
all the rest.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We should free urbs starting at [i-1] not [i].
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global wacom_sys_irq() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several functions in USB core overlap with global functions.
The linker appears to do the right thing, but it is bad practice and makes
debugging harder.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanup/clarification in the ethernet gadget driver, using standard
calls to test for Ethernet multicast and broadcast addresses.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as809b) moves the declaration of the hub driver's private
data structure from hub.h into the hub.c source file. Lots of other
files import hub.h; they have no need to know about the details of the
hub driver's private data.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix STATUS_PACKETS_* macros, where "&&" was mistakenly used where
"&" should have.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as814) adds usb_autopm_set_interface() to the autosuspend
API. It also provides convenient wrapper routines,
usb_autopm_enable() and usb_autopm_disable(), for drivers that want
to specify directly whether autosuspend should be allowed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as813) gathers together common code for USB interface
autosuspend/autoresume.
It also adds some simple checking at the time an autosuspend request
is made, to see whether the request will fail. This way we don't
add a workqueue entry when it would end up doing nothing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have no benefits of having the usb_endpoint_* functions as functions,
but making them inline saves text and data segment sizes:
text data bss dec hex filename
14893634 3108770 1108840 19111244 1239d4c vmlinux.func
14893185 3108566 1108840 19110591 1239abf vmlinux.inline
This is the result of a 2.6.19-rc3 kernel compiled with GCC 4.1.1 without
CONFIG_MODULES, CONFIG_CC_OPTIMIZE_FOR_SIZE, CONFIG_REGPARM options set.
USB support is fully enabled (while most of the other drivers are not),
and that kernel has most of the USB code ported to use the endpoint
functions.
That happens because a call to those functions are expensive (in terms
of bytes), while the function's size is smaller or have the same 'size' of
the call.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as811) removes some stale testing code from the root-hub
resume routine in ohci-hcd. It also adds a spin_lock_irq() call that
inadvertently got left out of an error pathway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
replace open coded kmemdup() to save some screen space,
and allow inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as808b) moves the Root Hub Status Change interrupt-disable
code in ohci-hcd back into the interrupt handler proper, to avoid the
chance of adverse interactions with mediocre hardware implementations.
It also deletes the root-hub status timer from within the interrupt-enable
routine. There's no need to poll for status any more once interrupts are
re-enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as806) fixes a compiler warning when ohci-hcd is built
with CONFIG_PM turned off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as804) makes USB driver matching ignore the interface
class, subclass, and protocol if the device class is Vendor Specific.
Drivers can override this policy by specifying a Vendor ID as part
of the match; then vendor-specific matches are allowed.
Linus Walleij has reported a problem this patch fixes. When a
particular mass-storage device is switched from mass-storage mode to
Media Transfer Protocol, the interface class remains set to mass-storage
and usb-storage binds to it erroneously, even though the device class
changes to Vendor-Specific.
This may cause a problem for some drivers until their match records can
be updated to include Vendor IDs. But if it does, then those records
were broken to begin with.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB HID driver doesn't include any code to handle a STALL on the
interrupt endpoint. While this may be uncommon, it does happen
sometimes. This patch (as805) adds a fix.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB Host Controllers accept a large number of devices per
host, which shows up as a large number of ports in its root hub.
When the number of ports in a hub device goes over 16, the activation
of the hub fails with the cryptic message in klogd.
hub 2-0:1.0: activate --> -22
Following this further, it was seen that:
hub_probe()
hub_configure()
generates pipe number
pseudo allocates buffer 'maxp' bytes in size using usb_maxpacket()
The endpoint descriptor for a root hub interrupt endpoint is
declared in
drivers/usb/core/hcd.c:hs_rh_config_descriptor and declares it
to be size two (supporting 15 devices max).
hub_activate()
usb_hcd_submit_urb()
rh_urb_enqueue()
urb->pipe is neither int nor ctl, so it errors out
rh_queue_status()
Returns -EINVAL because the buffer length is smaller
than the minimum needed to report all the hub port
bits as in accordance with USB2.0[11.12.3]. There has
to be trunc((PORTS + 1 + 7) / 8) bytes of space at
least.
Alan Stern confirmed that the reason for reading maxpktsize and not
the right amount is because some hubs are known to return more data
and thus cause overflow.
So this patch simply changes the code to make the interrupt endpoint's
max packet size be at least the minimum required by USB_MAXCHILDREN
(instead of a fixed magic number) and add documentation for that. This
way we are always ahead of the limit.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current Wireless USB host hardware (Intel i1480 for example) allows up
to 22 devices to connect, thus bringing up the max number of children
in the WUSB Host Controller to 22 'fake' ports. Upcoming hardware
might raise that limit.
Makes almost no difference to go to 31, as the bit arrays are
byte-aligned (plus an extra bit in general), so 22 bits fit in 4 bytes
as 31 do.
As well, the only other array that depends on USB_MAXCHILDREN is
'struct usb_hub->indicator'. By declaring it 'u8' instead of 'enum
hub_led_mode', we reduce the size of each entry from 4 bytes (in i386)
to 1, which will add as we when are doubling USB_MAXCHILDREN
(with 16 the size of that array is 64 bytes, with 31 would be 128; by
using u8 that goes down to 31 bytes).
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies blk_rq_map/unmap_user() and the cdrom and scsi_ioctl.c
users so that it supports requests larger than bio by chaining them together.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Correct a problem seen on later kernels running the NetPIPE application.
Specifically, NetPIPE would begin running very slowly at the 1533 packet
size. It was determined that Spidernet slowed with an idle DMA engine.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In an earlier patch, code was added to pad packets that were less that
ETH_ZLEN (60) bytes using the skb_pad function. This has caused hangs when
accessing certain NFS mounted file systems. This patch removes the check
and solves the NFS problem. The driver, with this patch, has been tested
extensively. Please apply.
Signed-off-by: James K Lewis <jklewis@us.ibm.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bonding driver unconditionnaly dereference get_stats function pointer
for each of its slave device. This patch
- adds a check for NULL dev->get_stats pointer in bond_get_stats
- prints a notice when the bonding device enslave a device without
get_stats function.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Confusingly NET_PCI is also set for for non-PCI EISA configurations where
building this driver will result in a build error due to a reference to
pci_release_regions.
While at it, remove the EXPERIMENTAL - in all its uglyness and despite
the sincerest attempts of the buggy hardware the driver is known to work.
Also limit the driver to the Atlas board - the only known system to ever
use the SAA9730 before Phillips ended the short live of the SAA9730.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes persistant -> persistent in actual C code. (part 1 changed
docs/comments).
Compile-tested.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Changes persistant -> persistent. www.dictionary.com does not know
persistant (with an A), but should it be one of those things you can
spell in more than one correct way, let me know.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch converts a if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch converts a if () BUG(); construct to BUG_ON();
which occupies less space, uses unlikely and is safer when
BUG() is disabled.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various .c/.h typos in comments (no code changes).
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
ib_ucm_cleanup_events() holds file_mutex while calling ib_destroy_cm_id().
This can deadlock since ib_destroy_cm_id() flushes event handlers, and
ib_ucm_event_handler() needs file_mutex, too. Therefore, drop the
file_mutex during the call to ib_destroy_cm_id().
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ib_cm_establish() function is replaced with a more generic
ib_cm_notify(). This routine is used to notify the CM that failover
has occurred, so that future CM messages (LAP, DREQ) reach the remote
CM. (Currently, we continue to use the original path) This bumps the
userspace CM ABI.
New alternate path information is captured when a LAP message is sent
or received. This allows QP attributes to be initialized for the user
when a new path is loaded after failover occurs.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipoib_neigh_free() is sometimes called while neighbour is still alive,
so it might still have queued skbs. Fix skb leak in this case.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SRP reallocates the IU buffers for tx_ring and rx_ring without freeing
the old buffers when it reconnects to a target. Fix this by keeping
the old IU buffers around.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix following problems in process_req() relating to cancellation:
- Function is wrongly doing another addr_remote() when cancelled,
which is not required.
- Make failure reporting immediate by using time_after_eq().
- On cancellation, -ETIMEDOUT was returned to the callback routine
instead of the more appropriate -ECANCELLED (users getting notified
may want to print/return this status, eg ucma_event_handler).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
It is possible to swap the CQs used for send_cq and recv_cq when
creating two different QPs. If these two QPs are then destroyed at
the same time, an AB-BA deadlock can occur because the CQ locks are
taken our of order. Fix this by always taking CQ locks in a fixed
order.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When initializing an mthca SRQ, the log_srq_size field should be the
log of the number of SRQ WQEs, not the log of the number of bytes in
the SRQ.
This affects only mthca drivers for memfree HCAs which set the initial
srq wqe counter (in the SW2HW transition) to a non-zero value.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a patch for ehca to fix a bug in prepare_sqe_to_rts(), which
used WQE address to iterate pending work requests. This might cause
an access violation since the queue pages can not be assumed to follow
each other consecutively. Thus, this patch introduces a few queue
functions to determine WQE offset based on its address and uses WQE
offset to iterate the pending work requests.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In iwcm_deref_id(), the comment says : "If the last reference is being
removed and iw_destroy_cm_id is waiting, wake up the waiting
thread". The second part of the comment, "and iw_destroy_cm_id is
waiting," is wrong, since this function either wakes the waiter
already waiting in iwcm_deref_id, or enables it (so that when
wait_for_completion() is performed later, it will immediately return).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove unnecessary cm_id_priv argument to copy_private_data(), and
change text to reflect the code. Fix couple of typos in comments.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we get IW_CM_EVENT_CONNECT_REQUEST message and encounter an error
(not in the LISTEN state, cannot create an id, cannot alloc
work_entry, etc), then the memory allocated by cm_event_handler() in
the event->private_data gets leaked. Since cm_work_handler has already
put the event on the work_free_list, this allocated memory is
leaked. High backlog value can allow DoS attacks.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Possible memory corruption scenario: after putting the work entry back
on the work_free_list, we call process_event() which dereferences
work->event, which could have been modified to another value
meanwhile.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The amso1100 driver was missing a couple of __devinit/__devexit
annotations for init/cleanup functions that are called from
__devinit/__devexit functions.
Reported by Randy Dunlap <randy.dunlap@oracle.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit b3b30f5e ("IB/mthca: Recover from catastrophic errors")
introduced some section mismatch breakage, because the error recovery
code tears down and reinitializes the device, which calls into lots of
code originally marked __devinit and __devexit from regular .text.
Fix this by getting rid of these now-incorrect section markers.
Reported by Randy Dunlap <randy.dunlap@oracle.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the Scsi_Host's max_cmd_len from 12 (default) to 16 for
SRP. Otherwise scsi_dispatch_cmd() won't pass down certain commands
such as READ CAPACITY 16, required for supporting disks > 2TB.
Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The qp_access_flags are for remote access permissions only, so
IB_ACCESS_LOCAL_WRITE is an invalid value. Remove it from the values
set by cm_init_qp_init_attr() and cma_init_ib_qp().
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open coded kmemdup() to save some screen space, and allow
inlining/not inlining to be triggered by gcc.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rewrite cma_req_handler error handling case to encapsulate
common code.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In queue_req(), use time_after_eq() instead of time_after()
for following reasons :
- Improves insert time if multiple entries with same time are
present.
- set_timeout need not be called if entry with same time
is added to the list (and that happens to be the entry
with the smallest time), saving atomic/locking operations.
- Earlier entries with same time are deleted first (fifo).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove redundant check of node_guid in cma_add_one().
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Optimize to test for an empty list first. This ends up simplifying
the code too.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This changes the type of variable "i" in rtl8169_init_one()
from "unsigned int" to "int". "i" is checked for < 0 later,
which can never happen for "unsigned". This results in broken
error handling.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many LLDs are missing sht->slave_destroy. The method is mandatory to
support device warm unplugging (echo 1 > /sys/.../delete). Without
it, libata might access released scsi device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
JMicron AHCI controllers set PORT_IRQ_IF_ERR on device errors. The
IRQ status bit indicates interface error or protocol mismatch and ahci
driver interprets it into AC_ERR_ATA_BUS. So, whenever an ATAPI
device raises check condition, ahci interprets it as ATA bus error and
thus resets it which, in turn, raises check condition thus creating a
reset loop and rendering the device unuseable.
This patch makes JMB controllers ignore PORT_IRQ_IF_ERR when
interpreting error condition.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Justin Tsai <justin@jmicron.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata: Fixup ata_sas_queuecmd to handle __ata_scsi_queuecmd failure
[PATCH] ahci: AHCI mode SATA patch for Intel ICH9
[PATCH] libata: don't schedule EH on wcache on/off if old EH
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 4e1bbd846d.
Quoth Daniel Drake <dsd@gentoo.org>:
"A user reported that commit 4e1bbd846d
(Remove unneeded packed attributes) breaks the zd1211rw driver on ARM."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the bug as reported in the kernel bug tracker
under the id 7244. The bug was simply that the interrupt lock has
been locked outside an interrupt without blocking the interrupt.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes ata_sas_queuecmd to properly handle a failure from
__ata_scsi_queuecmd.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH9 AHCI controller DID's for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do not schedule EH for revalidation on wcache on/off if old EH. Old
EH cannot handle it and will result in WARN_ON()'s and oops.
This closes bug #7412.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[XFRM] STATE: Fix to respond error to get operation if no matching entry exists.
[NET]: Re-fix of doc-comment in sock.h
[6PACK]: Masking bug in 6pack driver.
[NET]: Fix kfifo_alloc() error check.
[UDP]: Make udp_encap_rcv use pskb_may_pull
[NETFILTER]: H.323 conntrack: fix crash with CONFIG_IP_NF_CT_ACCT
The tda10086 causes an oops (divide by zero) if a zero symbol rate is used;
this prevents this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The old code would accept any device on the same i2c address as the
saa711x chips as an saa711x. However, this fails with saa717x chips,
which use that same address and so are misdetected as a saa7111. Now
check whether the chip is really a saa711x model.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sparse noticed a lock imbalance in read_from_buf(). Further inspection shows
that the lock should not be held when the function exits.
This adds a spin_unlock_irqrestore(), so that every exit path of the
read_from_buf() function is consistent. The unlock was missing on an error
path.
Signed-off-by: Ira W. Snyder <devel@irasnyder.com>
Signed-off-by: Hans J. Koch <koch@hjk-az.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes to DISEQC on these cards inadvertently broke normal tone/voltage
signalling. This restores the necessary function.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like a broken masking to me, binary not is used where bitwise
not was intended.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a bug. When checking for ati_remote->outbuf we free freeing
ati_remote->inbuf so we end up freeing ati_remote->inbuf twice.
Also the checks for 'ati_remote->inbuf != NULL' and 'ati_remote->outbuf !=
NULL' are redundant as usb_buffer_free() does this.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The return value of platform_device_register_simple() should be checked by
IS_ERR().
This patch also fix misc_register() error case. Because misc_register()
returns error code.
Cc: Sebastien Bouchard <sebastien.bouchard@ca.kontron.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes a module_exit function that sgiioc4 should not have had.
It seems that the IDE layer doesn't support submodule unloading. sgiioc4 was
the only driver in drivers/ide/pci that had an exit function. After an
unload, the devices would stay around and the next attempt to reference would
crash...
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: "Bartlomiej Zolnierkiewicz" <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dev->devt_attr is allocated in device_add() but it is never freed in
device_del() in the drivers/base/core.c file (reported by kmemleak).
Signed-off-by: Catalin Marinas <catalin.marinas@gmail.com>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The correct order is: NULL check before dereference
This was a guaranteed NULL dereference with debugging enabled since
rs5c372_sysfs_show_osc() does actually pass NULL...
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I got a lockdep warning when running "rtctest" so I though it'd be good
to see what was up.
- The warning was for rtc->irq_task_lock, gotten from rtc_update_irq()
by irq handlerss ... but in a handful of other cases, grabbed without
blocking IRQs.
- Some callers to rtc_update_irq() were not ensuring IRQs were blocked,
yet the routine expects that; make sure all callers block IRQs.
It would appear that RTC API tests haven't been part of anyone's kernel
regression test suite recently, at least not with lockdep running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The RTC framework has an irq_set_freq() method that should be used to manage
the periodic IRQ frequency, but the current ioctl logic doesn't know how to do
that. This patch teaches it how.
This means that drivers implementing irq_set_freq() will automatically support
RTC_IRQP_{READ,SET} ioctls; that logic doesn't need duplication within the
driver.
[akpm@osdl.org: export rtc_irq_set_freq]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
processor_perflib.c::acpi_processor_ppc_notifier() check if the value
returned by the processor's _PPC method is 0 and return failed if so.
This is wrong since 0 indicate that the bios think the processor can go
to the highest frequency. This patch for example fix the HP NX 6125 to
allow its highest frequency to be available.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Cc: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Not all graphic page remappers support physical addresses over the 4GB
mark for remapping, so while some do (the AMD64 GART always did, and I
just fixed the i965 to do so properly), we're safest off just forcing
GFP_DMA32 allocations to make sure graphics pages get allocated in the
low 32-bit address space by default.
AGP sub-drivers that really care, and can do better, could just choose
to implement their own allocator (or we could add another "64-bit safe"
default allocator for their use), but quite frankly, you're not likely
to care in practice.
So for now, this trivial change means that we won't be allocating pages
that we can't map correctly by mistake on x86-64.
[ On traditional 32-bit x86, this could never happen, because GFP_KERNEL
would never allocate any highmem memory anyway ]
Acked-by: Andi Kleen <ak@suse.de>
Acked-by: Dave Jones <davej@redhat.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces a i965-specific "mask_memory()" function that knows
about the extended physical addresses that the i965 supports. This
allows us to correctly map in physical memory in the >4GB range into the
GTT.
Also simplify/clean-up the i965 case for the aperture sizing by just
returning the fixed 512kB size from "fetch_size()". We don't really
care that not all of the aperture may be visible - the only thing that
cares about the aperture size is the Intel "stolen memory" calculation,
which depends on the fixed size.
Cc: Keith Packard <keithp@keithp.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Add missing unlock in tg3_open() error path.
[IPV6]: Fix address/interface handling in UDP and DCCP, according to the scoping architecture.
[IRDA]: Lockdep fix.
[BLUETOOTH]: Fix unaligned access in hci_send_to_sock.
[XFRM]: nlmsg length not computed correctly in the presence of subpolicies
[XFRM]: Sub-policies broke policy events
[IGMP]: Fix IGMPV3_EXP() normalization bit shift value.
[Bluetooth] Ignore L2CAP config requests on disconnect
[Bluetooth] Always include MTU in L2CAP config responses
[Bluetooth] Check if RFCOMM session is still attached to the TTY
[Bluetooth] Handling pending connect attempts after inquiry
[Bluetooth] Attach low-level connections to the Bluetooth bus
[IPV6] IP6TUNNEL: Add missing nf_reset() on input path.
[IPV6] IP6TUNNEL: Delete all tunnel device when unloading module.
[IPV6] ROUTE: Do not enable router reachability probing in router mode.
[IPV6] ROUTE: Prefer reachable nexthop only if the caller requests.
[IPV6] ROUTE: Try to use router which is not known unreachable.
Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipath uses skb functions and won't build without CONFIG_NET.
Spotted by Randy Dunlap.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a quick hack to overcome the fact that SRCU currently does not
allow static initializers, and we need to sometimes initialize those
things before any other initializers (even "core" ones) can do so.
Currently we don't allow this at all for modules, and the only user that
needs is right now is cpufreq. As reported by Thomas Gleixner:
"Commit b4dfdbb3c7 ("[PATCH] cpufreq:
make the transition_notifier chain use SRCU breaks cpu frequency
notification users, which register the callback > on core_init
level."
Cc: Thomas Gleixner <tglx@timesys.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@osdl.org>,
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix printk format warnings:
drivers/char/ftape/zftape/zftape-buffers.c:87: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
drivers/char/ftape/zftape/zftape-buffers.c:104: warning: format '%d' expects type
'int', but argument 3 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Having unbound PCMCIA devices: doing a 'find /sys' after a 'rmmod pcmcia'
gives an oops because the pcmcia_device is not unregisterd from the driver
core.
fixes bugzilla #7481
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Pavol Gono <Palo.Gono@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit 37605a6900.
Again.
This same bug has now been introduced twice: it was done earlier by
commit b8d35192c5, only to be reverted
last time in commit 72945b2b90.
We must NOT try to queue up notify handlers to another thread than the
normal ACPI execution thread, because the notifications on some systems
seem to just keep on accumulating until we run out of memory and/or
threads.
Keeping events within the one deferred execution thread automatically
throttles the events properly.
At least the Compaq N620c will lock up completely on the first thermal
event without this patch reverted.
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
