The udbg low level io layer has an issue with udbg_getc() returning a
char (unsigned on ppc) instead of an int, thus the -1 if you had no
available input device could end up turned into 0xff, filling your
display with bogus characters. This fixes it, along with adding a little
blob to xmon to do a delay before exiting when getting an EOF and fixing
the detection of ADB keyboards in udbg_adb.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When compiling without BOOTX_TEXT the following warning is emitted.
Fix up the definition to only be made when required.
CC arch/powerpc/platforms/powermac/udbg_adb.o
.../arch/powerpc/platforms/powermac/udbg_adb.c:41: warning:
`udbg_adb_use_btext' defined but not used
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
udbg_adb_init() has become dependent on btext_drawchar, even when
BOOTX_TEXT support is not selected. This leads to the error below.
Make the check dependant on BOOTX_TEXT.
LD .tmp_vmlinux1
arch/powerpc/platforms/built-in.o(.toc1+0xa40): undefined
reference to `btext_drawchar'
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
23-rpaphp-migrate.patch (parts)
This patch moves some pci device add & remove code from the PCI
hotplug directory to the arch/powerpc/kernel directory, and cleans
it up a tad. The primary reason for this is that the code performs
some fairly generic operations that are shared with the PCI error
recovery code (living in the arch/powerpc/kernel directory).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
22-rpaphp-eliminate-dupe-code.patch (parts)
The RPAPHP code contains two routines that appear to be gratuitous
copies of very similar pci code. In particular,
rpaphp_claim_resource ~~ pci_claim_resource
rpadlpar_claim_one_bus == pcibios_claim_one_bus
This makes pcibios_claim_one_bus from arch/powerpc/kernel/pci_64.c
available to the RPAPHP code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
20-rpaphp-eeh-cleanup.patch
This patch move some code from the rpaphp directory, to the powerpc
directory, where it should have been all along (Among other things, I
need it in the powerpc directory for the PCI error recovery.)
Please note that patch affects TWO maintainers: Paul, after applying
the powerpc part, please ask that GregKH appli the PCI part. It is safe
to have the powerpc part go in first. It would be bad to have the
PCI part go in first.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I started to add missing of_node_put() calls to the routines that
determine the number of cells for memory. Decided to combine the
routines instead of making separate node lookups. Changed variable
names to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the new serial probe code with some PCI MMIO UARTs, and fixes
CHRP build with ARCH=powerpc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Thu, 2005-11-24 at 12:51 +0000, David Woodhouse wrote:
> Somehow this one slipped through the cracks; when we ended up in
> do_signal() on a 32-bit kernel but without having the caller-saved
> registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
> ensure they got saved later.
Oh, and if we actually set the flag, then we fairly quickly find out
that I was a bit overzealous in copying code from entry_64.S ... :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somehow this one slipped through the cracks; when we ended up in
do_signal() on a 32-bit kernel but without having the caller-saved
registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
ensure they got saved later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2005-11-22 at 15:49 +1100, Benjamin Herrenschmidt wrote:
> This moves the discovery of legacy serial ports to a separate file,
> makes it common to ppc32 and ppc64, and reworks it to use the new OF
> address translators to get to the ports early. This new version can also
> detect some PCI serial cards using legacy chips and will probably match
> those discovered port with the default console choice.
This makes it deal with the fact that the Pegasos firmware reports that
its clock frequency is zero...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My previous patches inadvertently broke building a G5 kernel with
CONFIG_XMON enabled. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers. The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere. This patch moves the
reg_save area out into its own array. This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the powerpc version of hugetlb_get_unmapped_area() entirely
ignores the hint address. The only way to get a hugepage mapping at a
specified address is with MAP_FIXED, in which case there's no way
(short of parsing /proc/self/maps) for userspace to tell if it will
clobber an existing mapping. This is inconvenient, so the patch below
makes hugepage mappings use the given hint address if possible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Sam Ravnborg pointed out that calling if_changed was redundant in the
rule since a prerequisite had to have changed for us to get there.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Add support for building uImages
Add support to build a kernel image bootable by u-boot.
Most of the makefile foo is taken from arch/ppc/boot/images/Makefile
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Encode the sub bus number into the real irq number (even though it
is always zero for now) so that we have enough information to do
the EOI in iseries_end_IRQ.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
ARCH=powerpc couldn't boot from BootX as it uses a "different" way of
getting in the kernel. This patch adds the necessary trampolines,
creating a flattened device-tree from the tree passed from MacOS, and
initializing the btext engine early for really-early debugging.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Parsing addresses extracted from Open Firmware isn't a simple matter. We
have various bits of code that try to do it in various place, including
some heuristics in prom.c that pre-parse addresses at boot and fill
device-nodes "addrs", but those are dodgy at best and I want to
deprecate them. So this patch introduces a new set of routines that
should be capable of parsing most types of addresses and translating
them into CPU physical addresses. It currently works for things on PCI
busses and ISA busses and should work on "standard" busses like the root
bus or the MacIO bus that don't put funky flags in addresses. If you
have other bus types that do use funky flags, you'll have to add new bus
type translators, which is fairly easy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2005-11-15 at 18:52 +0000, David Woodhouse wrote:
> This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
> and brings the ppc32 and ppc64 code slightly closer together.
Needs this unless your binutils, like mine, are clever enough to notice
my stupidity and fix it up automatically...
Spotted by Paul.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a scheduler for SPUs to make it possible to use
more logical SPUs than physical ones are present in the
system.
Currently, there is no support for preempting a running
SPU thread, they have to leave the SPU by either triggering
an event on the SPU that causes it to return to the
owning thread or by sending a signal to it.
This patch also adds operations that enable accessing an SPU
in either runnable or saved state. We use an RW semaphore
to protect the state of the SPU from changing underneath
us, while we are holding it readable. In order to change
the state, it is acquired writeable and a context save
or restore is executed before downgrading the semaphore
to read-only.
From: Mark Nutter <mnutter@us.ibm.com>,
Uli Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the source code that is used to generate spu_save_dump.h and
spu_restore_dump.h. Since a full spu tool chain is needed to
generate these files, the default remains to use the shipped
versions in order to keep the number of tools for building the
kernel down.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the code needed to perform a context switch from
spufs, following the recommended 76-step sequence.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add some infrastructure for saving and restoring the context of an
SPE. This patch creates a new structure that can hold the whole
state of a physical SPE in memory. It also contains code that
avoids races during the context switch and the binary code that
is loaded to the SPU in order to access its registers.
The actual PPE- and SPE-side context switch code are two separate
patches.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the current version of the spu file system, used
for driving SPEs on the Cell Broadband Engine.
This release is almost identical to the version for the
2.6.14 kernel posted earlier, which is available as part
of the Cell BE Linux distribution from
http://www.bsc.es/projects/deepcomputing/linuxoncell/.
The first patch provides all the interfaces for running
spu application, but does not have any support for
debugging SPU tasks or for scheduling. Both these
functionalities are added in the subsequent patches.
See Documentation/filesystems/spufs.txt on how to use
spufs.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the necessary core bus support used by device drivers
that sit on the IBM GX bus on modern pSeries machines like the Galaxy
infiniband for example. It provide transparent DMA ops (the low level
driver works with virtual addresses directly) along with a simple bus
layer using the Open Firmware matching routines.
Signed-off-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
and brings the ppc32 and ppc64 code slightly closer together.
The ppc64 code was checking current_thread_info()->flags twice in the
syscall exit path; once for TIF_SYSCALL_T_OR_A before disabling
interrupts, and then again for TIF_SIGPENDING|TIF_NEED_RESCHED etc after
disabling interrupts. Now we do the same as ppc32 -- check the flags
only once in the fast path, and re-enable interrupts if necessary in the
ptrace case.
The patch abolishes the 'syscall_noerror' member of struct thread_info
and replaces it with a TIF_NOERROR bit in the flags, which is handled in
the slow path. This shortens the syscall entry code, which no longer
needs to clear syscall_noerror.
The patch adds a TIF_SAVE_NVGPRS flag which causes the syscall exit slow
path to save the non-volatile GPRs into a signal frame. This removes the
need for the assembly wrappers around sys_sigsuspend(),
sys_rt_sigsuspend(), et al which existed solely to save those registers
in advance. It also means I don't have to add new wrappers for ppoll()
and pselect(), which is what I was supposed to be doing when I got
distracted into this...
Finally, it unifies the ppc64 and ppc32 methods of handling syscall exit
directly into a signal handler (as required by sigsuspend et al) by
introducing a TIF_RESTOREALL flag which causes _all_ the registers to be
reloaded from the pt_regs by taking the ret_from_exception path, instead
of the normal syscall exit path which stomps on the callee-saved GPRs.
It appears to pass an LTP test run on ppc64, and passes basic testing on
ppc32 too. Brief tests of ptrace functionality with strace and gdb also
appear OK. I wouldn't send it to Linus for 2.6.15 just yet though :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the EXPORT_SYMBOL'ed but completely unused variable
ucSystemType and removes the unneeded EXPORT_SYMBOL(_prep_type).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sonny has noticed hotplug CPU on ppc64 is broken in 2.6.15-*. One of the
problems is that htab_initialize_secondary is called when a cpu is being
brought up, but it is marked __init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that commit f9bd170a87
broke the cascade from XICS to i8259 on pSeries machines; specifically
we ended up not ever doing the EOI on the XICS for the cascade. The
result was that interrupts from the serial ports (and presumably any
other devices using ISA interrupts) didn't get through. This fixes
it and also simplifies the code, by doing the EOI on the XICS in the
xics_get_irq routine after reading and acking the interrupt on the
i8259.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't restore the volatile registers in the syscall exit
path, we need to make sure we don't leak any potentially interesting
values from the kernel to userspace. This was already the case for
all except r11. This makes it use r11 for an MSR value, so r11 will
have an (uninteresting) MSR value in it on return to userspace.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that sets the clock spreading feature of the Intrepid ASIC
must not be run on some machine models or those won't boot. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64, when opening a new hugepage region, we need to make sure any
old normal-page SLBs for the area are flushed on all CPUs. There was
a bug in this logic - after putting the new hugepage area masks into
the thread structure, we copied it into the paca (read by the SLB miss
handler) only on one CPU, not on all. This could cause incorrect SLB
entries to be loaded when a multithreaded program was running
simultaneously on several CPUs. This patch corrects the error,
copying the context information into the PACA on all CPUs using the mm
in question before flushing any existing SLB entries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute. We were not doing this
for hugepages, this patch corrects the situation.
We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.
Tested on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.
Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.
Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.
For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 64k pages patch changed the meaning of one argument passed to the
low level hash functions (from "large" it became "psize" or page size
index), but one of the call sites wasn't properly updated, causing
potential random weird problems with huge pages. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This bug exists in the current code and prevents machines from booting
with numa enabled if there is a node that does not contain memory.
Workaround is to boot with 'numa=off'. Looks like a simple typo.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's never been a hardware platform that has both pSeries/RPA LPAR
hypervisor and stab (pre-POWER4 segment management). This removes
the redundant code in stab_initalize().
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the correct pointer to clear the memory of the return values,
to prevent stack corruption in the callers stackframe.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug noticed by Paolo Galtieri and fixed for ARCH=ppc in
the previous commit (ppc: fix floating point register corruption).
This fixes the arch/powerpc code by adding preempt_disable/enable,
and also cleans it up a bit by pulling out the code that discards
any lazily-switched CPU register state into a new function, rather
than having that code repeated in three places.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Both 32-bit and 64-bit use the same inline flush_icache_range definition
now, so both need to export __flush_icache_range, not just 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces the (in my opinion horrible) VM_UNMAPPED logic with very
explicit support for a "remapped page range" aka VM_PFNMAP. It allows a
VM area to contain an arbitrary range of page table entries that the VM
never touches, and never considers to be normal pages.
Any user of "remap_pfn_range()" automatically gets this new
functionality, and doesn't even have to mark the pages reserved or
indeed mark them any other way. It just works. As a side effect, doing
mmap() on /dev/mem works for arbitrary ranges.
Sparc update from David in the next commit.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Blah. The patch [0] I recently sent fixing errors with
in_hugepage_area() and prepare_hugepage_range() for powerpc itself has
an off-by-one bug. Furthermore, the related functions
touches_hugepage_*_range() and within_hugepage_*_range() are also
buggy. Some of the bugs, like those addressed in [0] originated with
commit 7d24f0b8a5 where we tweaked the
semantics of where hugepages are allowed. Other bugs have been there
essentially forever, and are due to the undefined behaviour of '<<'
with shift counts greater than the type width (LOW_ESID_MASK could
return non-zero for high ranges with the right congruences).
The good news is that I now have a testsuite which should pick up
things like this if they creep in again.
[0] "powerpc-fix-for-hugepage-areas-straddling-4gb-boundary"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the removal of include/asm-powerpc, we no longer need
arch/powerpc/include/asm for the 64 bit build. We also do not need
-Iarch/powerpc for the 64 bit build either.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 7d24f0b8a5 fixed bugs in the ppc64 SLB
miss handler with respect to hugepage handling, and in the process tweaked
the semantics of the hugepage address masks in mm_context_t.
Unfortunately, it left out a couple of necessary changes to go with that
change. First, the in_hugepage_area() macro was not updated to match,
second prepare_hugepage_range() was not updated to correctly handle
hugepages regions which straddled the 4GB point.
The latter appears only to cause process-hangs when attempting to map such
a region, but the former can cause oopses if a get_user_pages() is
triggered at the wrong point. This patch addresses both bugs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in kprobes that can cause an Oops or even a crash when a return
probe is installed on one of the following functions: sys_execve,
do_execve, load_*_binary, flush_old_exec, or flush_thread. The fix is to
remove the call to kprobe_flush_task() in flush_thread(). This fix has
been tested on all architectures for which the return-probes feature has
been implemented (i386, x86_64, ppc64, ia64). Please apply.
BACKGROUND
Up to now, we have called kprobe_flush_task() under two situations: when a
task exits, and when it execs. Flushing kretprobe_instances on exit is
correct because (a) do_exit() doesn't return, and (b) one or more
return-probed functions may be active when a task calls do_exit(). Neither
is the case for sys_execve() and its callees.
Initially, the mistaken call to kprobe_flush_task() on exec was harmless
because we put the "real" return address of each active probed function
back in the stack, just to be safe, when we recycled its
kretprobe_instance. When support for ppc64 and ia64 was added, this safety
measure couldn't be employed, and was eventually dropped even for i386 and
x86_64. sys_execve() and its callees were informally blacklisted for
return probes until this fix was developed.
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restore an earlier mod which went missing in the powerpc reshuffle: the 4xx
mmu_mapin_ram does not need to take init_mm.page_table_lock.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update comments (only) on page_table_lock and mmap_sem in arch/powerpc.
Removed the comment on page_table_lock from hash_huge_page: since it's no
longer taking page_table_lock itself, it's irrelevant whether others are; but
how it is safe (even against huge file truncation?) I can't say.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Email address update, changing old work address to personal (permanent)
one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Although we tend to associate VM_RESERVED with remap_pfn_range, quite a few
drivers set VM_RESERVED on areas which are then populated by nopage. The
PageReserved removal in 2.6.15-rc1 changed VM_RESERVED not to free pages in
zap_pte_range, without changing those drivers not to set it: so their pages
just leak away.
Let's not change miscellaneous drivers now: introduce VM_UNPAGED at the core,
to flag the special areas where the ptes may have no struct page, or if they
have then it's not to be touched. Replace most instances of VM_RESERVED in
core mm by VM_UNPAGED. Force it on in remap_pfn_range, and the sparc and
sparc64 io_remap_pfn_range.
Revert addition of VM_RESERVED to powerpc vdso, it's not needed there. Is it
needed anywhere? It still governs the mm->reserved_vm statistic, and special
vmas not to be merged, and areas not to be core dumped; but could probably be
eliminated later (the drivers are probably specifying it because in 2.4 it
kept swapout off the vma, but in 2.6 we work from the LRU, which these pages
don't get on).
Use the VM_SHM slot for VM_UNPAGED, and define VM_SHM to 0: it serves no
purpose whatsoever, and should be removed from drivers when we clean up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were using udelay in the loop on the primary cpu waiting for the
secondary cpu to take the timebase value. Unfortunately now that
udelay uses the timebase, and the timebase is stopped at this point,
the udelay never terminated. This fixes it by not using udelay, and
increases the number of loops before we time out to compensate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This involves some minor changes: a few unused functions that the
ppc32 pci.c provides are no longer declared here or exported;
pcibios_assign_all_busses now just refers to the pci_assign_all_buses
variable on both 32-bit and 64-bit; pcibios_scan_all_fns is now
just 0 instead of a function that always returns 0 on 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm-ppc64/imalloc.h is only included from files in arch/powerpc/mm.
We already have a header for mm local definitions,
arch/powerpc/mm/mmu_decl.h. Thus, this patch moves the contents of
imalloc.h into mmu_decl.h. The only exception are the definitions of
PHBS_IO_BASE, IMALLOC_BASE and IMALLOC_END. Those are moved into
pgtable.h, next to similar definitions of VMALLOC_START and
VMALLOC_SIZE.
Built for multiplatform 32bit and 64bit (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Trying to set the priority would just disable the interrupt due to an
incorrect mask used. We rarely use that call, in fact, I think only in
the powermac code for the cmd-power key combo that triggers xmon. So it
got unnoticed for a while.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
make defconfig will now use arch/powerpc/configs/ppc64_defconfig
if running on a ppc64 system. I need to add an
arch/powerpc/configs/ppc_defconfig sometime.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes 32-bit CHRP systems use the RTAS time-of-day routines if
available. It fixes a bug in the RTAS time-of-day routines where they
were storing a 64-bit timebase value in an unsigned long by making
those variables u64. Also, the direct-access time-of-day routines
had the wrong convention for the month and year in the struct rtc_time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_dedicated_idle() was using __get_tb which used to be defined
in asm/delay.h. Change it to use get_tb from asm/time.h, which is
in fact exactly the same thing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also deletes the now-unused Makefiles under arch/ppc64.
Both of the files moved over could use some merging, but for now I
have moved them as-is and arranged for them to be used only in 64-bit
kernels. For 32-bit kernels we still use arch/ppc/kernel/idle.c and
drivers/char/generic_nvram.c as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The config option SPAN_OTHER_NODES was created so that we could
make pSeries numa layouts work within the DISCONTIG memory model.
Now that DISCONTIG has been replaced by SPARSEMEM, we can eliminate
this option.
I'll be sending a separate patch to Andrew to remove the arch
independent code as pSeries was the only arch that needed this.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges align.c, the result isn't quite what was in ppc64 nor
what was in ppc32 :) It should implement all the functionalities of both
though. Kumar, since you played with that in the past, I suppose you
have some test cases for verifying that it works properly before I dig
out the 601 machine ? :)
Since it's likely that I won't be able to test all scenario, code
inspection is much welcome.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My earlier merge of delay.h introduced a timebase-based udelay for
32-bit machines but also broke the 601, which doesn't have the
timebase register. This fixes it by using the 601's RTC register on
the 601, and also moves __delay() and udelay() to be out-of-line in
arch/powerpc/kernel/time.c. These functions aren't really performance
critical, after all.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reserve the Maple RTC I/O resource. Needed now we use genrtc.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replacing the string labels with numbers saves 117 bytes in the final zImage.
These local labels are not discared.
Signed-off-by: Olaf Hering <olh@suse.de>
arch/powerpc/boot/crt0.S | 23 +++++++++++------------
1 files changed, 11 insertions(+), 12 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the kernel supports both G5 and pSeries, and CONFIG_EEH is enabled,
eeh_init() is (quite reasonably) never called when we boot on a G5. Yet
eeh_check_failure() still gets called. We should avoid doing that if
!eeh_subsystem_enabled.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The vDSO functions should have the same calling convention as a syscall.
Unfortunately, they currently don't set the cr0.so bit which is used to
indicate an error. This patch makes them clear this bit unconditionally
since all functions currently succeed. The syscall fallback done by some
of them will eventually override this if the syscall fails.
This also changes the symbol version of all vdso exports to make sure
glibc can differenciate between old and fixed calls for existing ones
like __kernel_gettimeofday.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This also extends the code to handle 32-bit ELF vmlinux files as well
as 64-bit ones. This is sufficient for booting on new-world 32-bit
powermacs (i.e. all recent machines).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hi,
The previous PowerBook patch didn't contain the feature table updates
for ARCH=powerpc. Here they are.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I discovered that in some cases (PowerMac for example) we wouldn't
properly map the PCI IO space on recent kernels. In addition, the code
for initializing PCI host bridges was scattered all over the place with
some duplication between platforms.
This patch fixes the problem and does a small cleanup by creating a
pcibios_alloc_controller() in pci_64.c that is similar to the one in
pci_32.c (just takes an additional device node argument) that takes care
of all the grunt allocation and initialisation work. It should work for
both boot time and dynamically allocated PHBs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somewhere we lost the include of udbg.h in lmb.c. While we're there, add a DBG
macro like every other file has and use it in lmb_dump_all().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My patch moving ppc64 RTC to genrtc was supposed to update all
defconfigs, but for some reason, the patch actually posted only had the
pseries one... ouch. This patch properly updates all defconfigs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch should fix the crashes we have been seeing on 64-bit
powerpc systems with a memory hole when sparsemem is enabled.
I'd appreciate it if people who know more about NUMA and sparsemem
than me could look over it.
There were two bugs. The first was that if NUMA was enabled but there
was no NUMA information for the machine, the setup_nonnuma() function
was adding a single region, assuming memory was contiguous. The
second was that the loops in mem_init() and show_mem() assumed that
all pages within the span of a pgdat were valid (had a valid struct
page).
I also fixed the incorrect setting of num_physpages that Mike Kravetz
pointed out.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These exported symbols are in arch/ppc/ but missing from arch/powerpc/ for
ppc32 builds.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Gary Byers, we were clearing the image of the FPSCR
(floating point status and control register) in the thread_struct before
copying it to the user stack when invoking a signal. Thus the task
would see its FPSCR getting cleared when it took a signal.
While fixing it I noticed that our swapcontext system call was also
clearing FPSCR. It shouldn't, so I fixed that too.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These machines don't have working ARCH=powerpc support yet, so make
them depend on BROKEN so people don't enable them inadvertently and
get compile errors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also deletes files in arch/ppc64 that are no longer used now that
we don't compile with ARCH=ppc64 any more.
Signed-off-by: Paul Mackerras <paulus@samba.org>
