When dynamic channel switch is enabled, trigger acs and switch to best
channel if wlan interference is found in 5g mac.
Change-Id: I56661f5c42a233a0dc0a6400d75cb8f5c0019706
CRs-Fixed: 2599176
In channel switch response start bss success event is used to
indicate the success in which the initial bss settings are done
that is leading to set the incorrect keys after the channel switch.
Use the channel change event to indicate channel switch success.
Change-Id: I0915ee78a97e5f27ce83c31cc673cb8820ae535b
CRs-Fixed: 2620809
The ch_params of sap_ctx->csr_roamProfile is not populated
correctly during SAP channel switching.
Fix it and send channel change event to supplicant with
correct seg0/seg1 value.
Change-Id: I7ef82c6e79b970edfee58d9960e8c6b42fa91ef8
CRs-Fixed: 2594973
Combine and print channel for ACS and roam channels, instead
of printing one channel at a time.
Change-Id: I398678e1843849bdf4f4c72f0315c626c97438a6
CRs-Fixed: 2623805
Enhance logs in ACS module to remove duplicate
prints and keep only useful logs to debug.
Change-Id: I2cf98fb8b4d7a8391617c9ce1baaa5ff6ad42114
CRs-Fixed: 2614609
Currently the logic in ACS for 0 scan results is
to select default channel from the ACS channel list,
but the available channels may not always be capable
of the max BW sent by ACS, for example in HW MODE as
ANY then all the channels 2.4ghz and 5ghz would be
present in the ACS channel list, 2.4ghz channels at
the first followed by the 5ghz channels, and if the
scan results are 0 then 2.4ghz channel would be
selected as default which should not be the case.
Fix is to remove the check to select default channel
and let me ACS algorithm decide the best channel
accounting other factors such as noise floor
and max tx rx clear count, power also.
Change-Id: I21e5d73e12fffb00c4996c406d62361b74db629f
CRs-Fixed: 2601141
If SAP start on 5G DFS channel, it will keep in CAC for 1 minute.
If Disable 5G by cmd: hostapd_cli -iwlan2 set setband 2G during
this minute, SAP won't switch to 2G since SAP isn't in started
state, and SAP start also fail since SAP operate channel
becomes disabled instead of DFS state, SAP will be hung in DFS
state.
Fix: When CAC complete and SAP start, check SAP operate channel
with wlan_reg_chan_has_dfs_attribute_for_freq.
After SAP started, will check for SAP restart,
if found current band is disabled, will switch to 2G band.
Change-Id: I3c29b5d324d4324ce958a5c2cd2102df2cc183ff
CRs-Fixed: 2601081
Currently during ACS process, if best channel after weight sorting
is not in PCL list, then further check if there is a channel in PCL
has some weight, if there is, then switch to this new channel.
Skip above process if best channel is already in PCL list.
Change-Id: I5bfb6d18c531e6b7b4ff0b8b2bb2bd47388fed0c
CRs-Fixed: 2589033
CRYPTO_SET_KEY_CONVERGED is a temporary flag which is used for
converged crypto component transition. The transition has already
been done, so cleanup legacy code related to the flag in HDD layer
and SAP module.
Change-Id: Ic92e44e53c63ba2752907ace3ffc0f55d18470e2
CRs-fixed: 2593520
wlan_set_vdev_crypto_prarams_from_ie() is defined in qcacmn code but
disabled in Kbuild if CONFIG_CRYPTO_COMPONENT=n, it caused runtime
error if run it.
The #ifdef/#else code should live in common code where define
wlan_set_vdev_crypto_prarams_from_ie(), but there is no motivation
from WIN side to add any code which is not converged.
And it is not appropriate to put it into exist head files, so just
define inlined wrapper functions to cover the not defined case.
Change-Id: I11916703fff860025728f904c8d3906eee1d0037
CRs-Fixed: 2592904
If g_enable_go_force_scc isn't enabled, P2P Go failed to switch
to 2G band when 5G disabled.
Fix: Check whether need switch channel for band restriction
first, check go force scc later.
Change-Id: Icf8de51321debea2806585d47d2bd4fc6486075e
CRs-Fixed: 2594279
Currently the driver does not allow the channels
12 and 13 for SAP ACS because most of the legacy
stations don't scan them and they can cause many
IOT issues. But if they are the only channels left
in the spectrum (for eg. all other channels became
unsafe), then the SAP would fail as the driver did
not consider channel 12-14 for ACS.
Fix is to consider 12-14 for ACS, remove them if
other channels are available and if they are the
only channels available in the spectrum, then start
the SAP on any one of these channels.
Change-Id: I599d0e95e9bdc3aed70d6a515d7a52c39846b6f2
CRs-Fixed: 2576635
When SAP is on 5G and STA connects to 6Ghz AP, the "force
SCC" logic will move SAP to STA home channel if SAP is 6Ghz capable.
If SAP is not 6Ghz capable, SAP will be moved to 2G (DBS) to
avoid MCC(5G+6G) for DBS HW and SAP will stay on 5G for non-DBS HW.
SAP is 6Ghz capable only when all of below statements are true:
a. SAP config includes WPA3 security - SAE,OWE,SuiteB.
b. SAP is configured by ACS range which includes any 6G channel or
configured by 6G Fixed channel.
c. SAP has no legacy clients (client doesn't support 6G band).
legacy client (non 6ghz capable): association request frame has no
6G band global operating Class.
Change-Id: I7e9723fd1b679326a3df61932850589e6e503f3d
CRs-Fixed: 2593569
Fix potential race condition issue when the sap_context
of adapter is null and it is accessed in work queue -
__policy_mgr_check_sta_ap_concurrent_ch_intf.
To acquire/release the "sap_context" by get/put API.
Change-Id: I91dacc6d45c377840f7d30f2f9ff902f53ccd8e8
CRs-Fixed: 2592524
Presently, during Subsystem Restart(SSR) the object references
are not released cleanly, invoke stop adapter during the SSR
to have common functionality between the netdevice going down
and SSR.
Change-Id: I2980379022f62ef27dea92868c8033c087544d50
CRs-Fixed: 2587443
Use frequency as parameter for channel overlap handling
APIs - csr_check_concurrent_channel_overlap,
csr_calc_chb_for_sap_phymode, csr_get_ch_from_ht_profile,
csr_handle_conc_chnl_overlap_for_sap_go.
Change-Id: Ie3c9d466f21d7313998328432c063b1f6c7e5d0f
CRs-Fixed: 2577706
When 5G band is disabled by set band, need SAP switch channel
to 2G. When 5G band is enabled again, need SAP switch back to
original 5G channel. When sta connecting, SAP can't switch
channel.
Merge logic of SAP channel switch for band change and for force
scc with sta, both are implemented in:
policy_mgr_check_concurrent_intf_and_restart_sap now.
After sta associate succeed or fail,
policy_mgr_check_concurrent_intf_and_restart_sap is called again
to check and try SAP CSA for band capability change.
Change-Id: I8574209aac3cabb748a8ec05050244f480e1a0e9
CRs-Fixed: 2589021
When SSR sap restart, vdev objmgr object will recreate new, if put set
vdev crypto pararams in wlan_hdd_cfg80211_start_bss(), it will not be
invoked by SSR sap restart procedure, so there is no crypto pararams in
vdev and lead to association failure when compare crypto pararams.
Move back set vdev crypto pararams to wlansap_start_bss so sap start
and restart will both invoke it.
Change-Id: I56656ffacbe153fbe73fb6e474048e055cb6a153
CRs-Fixed: 2584138
with a new change I9b2b1ead3b4502022aeefc08359037457bb051f9 added for
to switch from 2.4g from 5g when an indication is received, During the
driver re-initliazation also this function is getting invoked and trying
access freed memory resulting in null pointer deference.
Donot process the function wlansap_set_band_csa when the driver is
recovering.
Change-Id: Iab67d5b77ffc98166bf421ff30bcf641e37fef6a
CRs-Fixed: 2587706
Set seg1 frequency segment in case of 5ghz 160Mhz as
the primary centre channel frequency of 160Mhz band.
Change-Id: Id541419c084d8cdf2a22e84170dbe68d731f5ad0
CRs-Fixed: 2587220
Fix compile issues when some features are disabled, the features are:
BUILD_DEBUG_VERSION
CONFIG_CP_STATS
CONFIG_HOST_OPCLASS
CONFIG_FEATURE_ROAM_DEBUG
There are some other features depends on each other, so enabled features to
qcs40x.snoc.perf_defconfig, the features are:
CONFIG_WLAN_FEATURE_FILS
CONFIG_WMI_ROAM_SUPPORT
CONFIG_WMI_STA_SUPPORT
CONFIG_REG_CLIENT
CONFIG_WLAN_FEATURE_DP_BUS_BANDWIDTH
CONFIG_WMI_CONCURRENCY_SUPPORT
CONFIG_LL_DP_SUPPORT
Change-Id: I6fa1eacb79576a955e593dbb9ac52083742275e3
CRs-Fixed: 2354496
Currently in case of LTE-coex event, the driver restarts
the SAP to a new channel if the current SAP operating
channel is unsafe.
In the current logic the driver gets the PCL apply the
logic to remove unsafe channels, NOL channels etc.
and then chose a final channel for the SAP.
Now for the case of standlaone SAP the PCL would contain
only 5ghz channels, and it may be the case that ACS
channel list contains only 2.4ghz channels because
the SAP was initially started on 2.4ghz band.
Now with the intersection of 2.4ghz and 5ghz, the driver
would not get anything left to restart the SAP and the SAP
restart would eventually fail.
Fix is to directly check the number of connections as 1,
that would mean only SAP is present, and if it is the
case, just restart the SAP on any other channel from the
ACS channel list rather than intersection with PCL.
Change-Id: If3a77ca877b2bf5e83ca64930e716936f680940f
CRs-Fixed: 2556054
Currently the driver in case of force SCC picks up
2.4ghz SCC channel if any other STA/AP is already
up on that channel, so in the process of shifting
in the API sap_validate_channel it picks up 2.4ghz
and calls a reg API to set the freq related params
to it. Now since the frequency for 2.4ghz is 40 mhz
capable the max BW supported for 2.4ghz becomes 40 and
the driver starts the SAP on 40mhz.
Now since the OBSS scan is offloaded to the hostpad
and now since it was driver which started the SAP
on 40mhz there is no mechanism to start OBSS scan
from driver, which leads to channel blockage if
any legacy 11g, 11b lient is operating on the channel.
Fix is to lower down the BW to 20Mhz if the SAP does a
force SCC in 2.4ghz.
Change-Id: I0d85dfb5e9e8332957d853173063e77d18ea600c
CRs-Fixed: 2581495
Currently the driver does not set weight calculated flag
in the spectrum channel structure for each channel as
true in 40, 80, 160 sorting case.
Now in the next iteration the weight calculation done
comes as false, and the weight is set as maximum
which leads to wrong channel and BW selection and the
last while running channel selection logic.
Fix is to set weight calculation done as true for all
the channels which come under the particular BW, and
skip the channels for which the weights are already
calculated.
Change-Id: Ib355dd5cf7c3aeeb5534bfa295785bdfc30eed86
CRs-Fixed: 2583538
1. Convert channel to frequency and use frequency
Regulatory API to check DFS status.
2. Skip dfs check for 6G channels.
Change-Id: I54b6d6a3ad25c192af4eec4e7f43932bada728b5
CRs-Fixed: 2580568
For SAP/P2P GO on 5G, when receive cmd to disable 5G band when
modem n79 band used, will move to 2G band via CSA.
1. If no active connection on 2G, select ch by safe list, or
channel 6.
2. If there is STA on 2G, force scc with it.
3. If there is SAP/GO on 2G, force scc with it.
4. Handle one race condition that if candidate is already
selected & FW has gone ahead with roaming or about to go ahead
when set_band comes, it will be complicated for FW to stop the
current roaming. Instead, host will check roam sync to make sure
the new AP is on 2G, or disconnect the AP.
5. If 2 SAP on 5G, move both to 2G and keep scc.
When Set band to enable 5G band again, restored all 5G SAP/Go..
Change-Id: I9b2b1ead3b4502022aeefc08359037457bb051f9
CRs-Fixed: 2580204
Currently if the first channel if seen in the normalize
acs weight array is found, the driver does not set the
freq present as false back, which leads to further
disabling all frequencies for SAP which should not be
the expectation.
Fix is to set the freq present as false again for the
next frequency.
Change-Id: Iabeb40179a0ef02cb51441b1148eea79b82d0ebf
CRs-Fixed: 2578551
Currently the driver does not fill the seg1 frequency
in case of 160 mhz which is used for SAP startup.
Fix is to Fill seg1 for 160 mhz BW in ACS result
Change-Id: Iffc61581290adf97d83e10b6a717c50afb750687
CRs-Fixed: 2575631
Currently the driver calculates the best channel
amoung the given spectrum and uses logic to select
best frequency amoung the BW members, but the logic
to maximize the weight before selecting the min
weight is wrong, and must be done after the selection
of the minimum weight frequency.
Fix is to maximize the weight after the minimum weight
channel is selected.
Change-Id: Ie196462fbcc4215e6eb655168d07305110ff0ee7
CRs-Fixed: 2578582
Currently in stop adapter the driver checks the ACS bit
in progress and then waits for it to get complete
Now if in scheduler thread the sap scan cb comes then
it will check to get op protect which would not be
granted as it is a pdev operation, and already a vdev
transition is in progress, hence the bit for acs in progress
would not get cleared.
Fix is to remove the check of op protect as it is no longer
needed since the stop adapter takes care of acs in progress.
Change-Id: Ifebaed87e3a798126031d9971dc801d60fd34ea6
CRs-Fixed: 2567157
Fix indentation issue in sap channel select to
avoid compile failures in auto branch compilers
Change-Id: Ifa92dfaaa349833d5651b7cdb66d87f039f0df36
CRs-Fixed: 2568414
In ACS, driver uses frame parser to get the HT/VHT/HE IE to fill
bandwidth, center freq etc. These info are already available in
scan entry so use them.
Change-Id: I5148f8aa20174b4fa0fc64acd7b74825e10ede03
CRs-Fixed: 2568513
Change vht_seg0_center_ch and vht_seg1_center_ch in acs_cfg
struct to vht_seg0_center_ch_freq, vht_seg1_center_ch_freq
respectively.
Change-Id: Ie3378376e6f31c239157c8eaaf3ceb22d2e35073
CRs-Fixed: 2564065
Change acs->start_ch and acs->end_ch to acs->start_ch_freq
and acs->end_ch_freq respectively.
Change-Id: I105cd618970c739340df29d58f635d01a68754d2
CRs-Fixed: 2564018
Acs changes for 6ghz to change chan to frequency
in the spectral params structure.
Change-Id: Iffd348ac5c2457b313b702a92b340a258992e764
CRs-Fixed: 2564043
Convert primary, secondary channel for acs cfg to freq as part
of ACS 6Ghz changes.
Change-Id: I4f6220b39dae91df070b0764fa8b048cdc6ad00f
CRs-Fixed: 2555988
At the time of starting / stopping 2nd or 3rd connection,
Host sends WMI_PDEV_SET_HW_CMDID command to FW to change
HW mode to DBS / Single-Mac based on concurrency rule.
FW upon receiving this command turns off TXRX chainmask
which means that radar pulses might get missed for
20ms - 50ms during CAC period. To fix this, Host should
block new connection when existing SAP is performing CAC
on DFS channel.
Change-Id: I51eb117afa763a6ef54211808875419026c9075b
CRs-Fixed: 2533717
For 6GHz support and to remove channel number ambiguity use policy
manager APIs updated for frequency in other modules. This change
covers following APIs:
policy_mgr_get_pcl
policy_mgr_update_with_safe_channel_list
policy_mgr_get_valid_chans_from_range
policy_mgr_get_valid_chans
policy_mgr_set_sap_mandatory_channels
policy_mgr_get_pcl_for_existing_conn
policy_mgr_get_mode_specific_conn_info
Change-Id: Ia21829345be2746cd3fc1f2337cfc90abf0c53f4
CRs-fixed: 2550092
