The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-algo-bit: Discard the mdelay data struct member
The i2c_algo_bit_data structure has an mdelay member, which is not
used by the algorithm code (the code has always been ifdef'd out.)
Let's discard it to save some code and memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Small driver suspend() fixes in preparation for the PRETHAW events:
- Only compare message events for equality against PM_EVENT_* codes;
not against integers, or using greater/less-than comparisons.
(PM_EVENT_* should really become a __bitwise thing.)
- Explicitly test for SUSPEND events (rather than not-something-else)
before suspending devices.
- Removes more of the confusion between a pm_message_t (wraps event code)
and a "state" ... suspend() originally took a target system state.
These updates are correct and appropriate even without new PM_EVENT codes.
benh: "I think in the Mesh case, we should handle the freeze case as well or
we might get wild DMA."
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The v4l2 API documentation for VIDIOC_ENUMSTD says:
To enumerate all standards applications shall begin at index
zero, incrementing by one until the driver returns EINVAL.
The actual code, however, tests the index this way:
if (index<=0 || index >= vfd->tvnormsize) {
ret=-EINVAL;
So any application which passes in index=0 gets EINVAL right off the bat
- and, in fact, this is what happens to mplayer. So I think the
following patch is called for, and maybe even appropriate for a 2.6.18.x
stable release.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 support should be disabled when no CONFIG_VIDEO_V4L1_COMPAT is defined,
to allow checking for broken V4L2 ports. This is very important during the
migration phase for V4L2 API.
However, userspace apps should be capable of using both APIs, since they need
to test at runtime, via VIDIOCGCAP ioctl, if V4L1 is supported. So, when
__KERNEL__ is not defined, those ioctls and corresponding structs should be
visible.
This patch also removes the obsolete defines HAVE_V4L1 and HAVE_V4L2, that
where causing some confusion, and were replaced by CONFIG_VIDEO_V4L1_COMPAT
and CONFIG_VIDEO_V4L2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tena_9533_di_pal_ranges use 0x04 instead the original 0x08 for the
UHF (range 2) switching. This is wrong and therefore nothing happens.
Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to make the UHF switch
working again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOCGMBUF should be compiled only when V4L1 support is selected, since
this ioctl is from the obsoleted API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In bugzilla #6943, Maxim Britov reported:
"I can enable Logitech quickcam support in .config, but it want be compile.
I have to add into drivers/media/video/Makefile:
obj-$(CONFIG_USB_QUICKCAM_MESSENGER) += usbvideo/"
He's right, just enable that driver as module while disabling every other
driver that gets into that directory, nothing will get compiled.
This patch fixes the Makefile.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without the LNA these tuners perform very poorly (read 'unwatchable') when
the signal is weak.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a wrong statement order the 'standard' module option didn't
work for 'G' model chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 assembled the bytes in the wrong order.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The compat_ioctl support of the pwc driver was dropped during the last update of the driver.
I suppose it was by mistake. If yes here is the patch to restore the support.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@looxix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A previous patch changed VBI_OFFSET to match what the datasheets say it
should be. However, the bt8x8 datasheets are wrong. The old value of
244 is closer to what is actually observed. The real value appears to
not be constant and is different for different chip revisions.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Take note of which sysfs files / groups that the pvrusb2 successfully
creates and only delete those specific items when tearing things
down. (Previously we just blindly tore everything down every time.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Revert bttv-driver.c from video_device_create_file() to use
class_device_create_file() again. video_device_create_file() is only
available when V4L1 is on.
Proper error checking is added for failure of class_device_create_file().
Will print error message and unroll partially created sysfs entries.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add proper error checking and roll-back for failure of
class_device_create_file() in videodev.c. Print error messages and
unroll partially created sysfs entries.
Also, failure of class_device_register() in video_register_device() is
handled correctly. It was failing to de-allocate the minor number. This
must be done in video_register_device(), since the caller has no way of
knowing if failure occurred before or after the class device was
registered.
Also added an error message if video_register_device() is called with
an unknown type, which should never happen.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A patch from Aug, 17 activated by mistake OVERLAY flag on cx88-video,
together with several cx88-blackbird cleanups. This makes the cx88 driver
to report:
/dev/video0 [v4l2]: ioctl VIDIOC_G_FBUF: Invalid argument
instead of:
/dev/video0 [v4l2]: no overlay support
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed usage of HAVE_V4L1
Including videodev.h will just include videodev2.h if V4L1 is not supported
V4L1 code at core drivers will honor CONFIG_V4L1_COMPAT stuff
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_code size is 24 on i386 and 32 on x86_64, so a proper handling is needed
on compat_ioctl32 to fix it.
This code should be tested, since just *a few* boards use this ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho pointed out that the pll test i2c transmission is slightly
wrong; it was transmitting a zero length message, and then reading from the
PLL. This was wrong; it should only be transmitting a single read i2c message.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Supplying a NULL i2c adapter to dvb_pll_attach is allowed, for example with
mt352 demods. However, the pll i2c probe will segfault because it does not
check for this.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix bug reported by Andrew de Quincey:
After cold boot the saa7146 DMA did not start if the demuxer was opened
before the frontend has locked to the signal.
DMA transfers will be started now if (and only if)
the frontend is locked and data should be sent to the demuxer.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check __must_check warnings for class_device_register and class_device_create_file
video_device_create_file was declared as a void, but instead should
return the int value of class_device_create_file.
Move the check from bttv-driver.c into v4l2-dev.h, because all other
callers of video_device_create_file must also be checked.
Replace the call to class_device_create_file in videodev.c with
video_device_create_file, as defined in v4l2-dev.h, so that the
return value of class_device_create_file will be checked.
Check the return value of class_device_register in videodev.c and
pvrusb2-sysfs.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the LG H06xF tuners, an auxiliary byte must be sent after the
standard four-byte i2c sequence. The code that does this is currently in
the wrong place, causing random bytes to be written to the tuner over
i2c in the set_type function.
This patch moves this code from set_type to default_set_tv_freq.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix keycode calculations (all codes for this remote were wrong due to a
lost + sign)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two different exports with the same name are not a good idea:
$ grep -r EXPORT_SYMBOL\(dmasound_init\) *
drivers/media/video/saa7134/saa7134-core.c:EXPORT_SYMBOL(dmasound_init);
sound/oss/dmasound/dmasound_core.c:EXPORT_SYMBOL(dmasound_init);
$
This patch renames the saa7134 dmasound_{init,exit} to
saa7134_dmasound_{init,exit}.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch just sets the option noninterlaced to 1 by default since
it has no known disadvantages. It is still possibe to get the old
behaviour by setting noninterlaced=0.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To prevent autoloading of the driver, as it then conflicts with every other
saa7146 device in existence.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix typo in comment for TDA9819
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It was pointed out on the mailing list that this PLL definition is broken. I
went back to the original dibusb driver and confirmed it used to use these
settings, as well as consulting the datasheet.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the stv0299 native DISEQC implementation instead of the bitbanging one
as required by the ves1893. This was originally found by Oliver Endriss.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The changes to add frontend reinitialisation moved the position where the
init() op is called into the frontend thread. Unfortunately, since DISEQC
operations do not use the frontend thread, this meant that DISEQC could be
called against an uninitalised frontend, leading to all sorts of trouble.
Patch fixes this by reinstating the original fronted intialisation call.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some cards have multiple possible addresses for their PLLs, with no other
way to tell if a PLL is present or not apart from probing to see if an i2c
device is present. This adds a quick check to see if an i2c device is
present at the given i2c address.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
