Some of the instances of tcp_sack_block are host-endian, some - net-endian.
Define struct tcp_sack_block_wire identical to struct tcp_sack_block
with u32 replaced with __be32; annotate uses of tcp_sack_block replacing
net-endian ones with tcp_sack_block_wire. Change is obviously safe since
for cc(1) __be32 is typedefed to u32.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_mc_sf_allow() expects addresses to be passed net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
->faddr is net-endian; annotated as such, variables inferred to be net-endian
annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The move of qdisc destruction to a rcu callback broke locking in the
entire qdisc layer by invalidating previously valid assumptions about
the context in which changes to the qdisc tree occur.
The two assumptions were:
- since changes only happen in process context, read_lock doesn't need
bottem half protection. Now invalid since destruction of inner qdiscs,
classifiers, actions and estimators happens in the RCU callback unless
they're manually deleted, resulting in dead-locks when read_lock in
process context is interrupted by write_lock_bh in bottem half context.
- since changes only happen under the RTNL, no additional locking is
necessary for data not used during packet processing (f.e. u32_list).
Again, since destruction now happens in the RCU callback, this assumption
is not valid anymore, causing races while using this data, which can
result in corruption or use-after-free.
Instead of "fixing" this by disabling bottem halfs everywhere and adding
new locks/refcounting, this patch makes these assumptions valid again by
moving destruction back to process context. Since only the dev->qdisc
pointer is protected by RCU, but ->enqueue and the qdisc tree are still
protected by dev->qdisc_lock, destruction of the tree can be performed
immediately and only the final free needs to happen in the rcu callback
to make sure dev_queue_xmit doesn't access already freed memory.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect use of RB_EMPTY_NODE in htb_safe_rb_erase, which makes it
skip nodes within the rbtree instead of nodes not in the tree, resulting
in crashes later on.
The root cause for this seems to be the very counter-intuitive behaviour
of the RB_EMPTY_NODE macro, which returns _false_ when the node is empty.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a minor buglet I came across by accident - when inet_init
fails to register raw_prot, it jumps to out_unregister_udp_proto which
should unregister UDP _and_ TCP.
Signed-off-by: Olaf Kirch <okir@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anyway, I've been asked to add support for managing DSCP codepoints,
so one can test DiffServ capable routers. It's very simple code and is
working for me.
Signed-off-by: Francesco Fondelli <francesco.fondelli@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached patch allows pktgen to produce 802.1Q and Q-in-Q tagged frames.
I have used it for stress test a bridge and seems ok to me.
Unfortunately I have no access to net-2.6.x git tree so the diff is against
2.6.17.13.
Signed-off-by: Francesco Fondelli <francesco.fondelli@gmail.com>
Acked-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevents filters from being added if the first generated
handle already exists.
Signed-off-by: Kim Nordlund <kim.nordlund@nokia.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
In case of non-blocking connects it is possible that the last user
of an ACL link quits before the connection has been fully established.
This will lead to a race condition where the internal state of a
connection is closed, but the actual link has been established and is
active. In case of Bluetooth 1.2 and later devices it is possible to
call create connection cancel to abort the connect. For older devices
the disconnect timer will be used to trigger the needed disconnect.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The local version information are needed to identify certain feature
sets of devices. They must be read on device init and stored for later
use. It is also possible to access them through the device model.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case of non-blocking socket calls we should return EINPROGRESS
and not EAGAIN.
Signed-off-by: Ulisses Furquim <ulissesf@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The command complete event of the exit periodic inquiry command must
clear the HCI_INQUIRY flag and finish the HCI request.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch assigns the next free HCI device identifier to Bluetooth
devices based on the SDIO interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch integrates the services of the Bluetooth protocols RFCOMM,
BNEP and HIDP into the driver model. This makes it possible to assign
the virtual TTY, network and input devices to a specific Bluetooth
connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch integrates the low-level connections (ACL and SCO) into the
driver model. Every connection is presented as device with the parent
set to its host controller device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
another possible dereference spotted by coverity (#cid 1390).
if the nlmsg_parse() call fails, we goto errout, where we call
dev_put(), with dev still initialized to NULL.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
pure s/u32/__be32/
[AV: large part based on Alexey's patches]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* add svc_getnl():
Take network-endian value from buffer, convert to host-endian
and return it.
* add svc_putnl():
Take host-endian value, convert to network-endian and put it
into a buffer.
* annotate svc_getu32()/svc_putu32() as dealing with network-endian.
* convert to svc_getnl(), svc_putnl().
[AV: in large part it's a carved-up Alexey's patch]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
multipath_wrandom.c::__multipath_lookup_weight() contains open-coded
attempt at inet_make_mask(); broken on big-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
multipath_set_nhinfo() (and underlying callback) take net-endian
network and netmask.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is interesting - we use net-endian value as search key, but
order the tree by *host-endian* comparisons of keys. OK since we only
care about lookups. Annotated inet_getpeer() and friends.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
argument and inferred net-endian variables in callers annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last argument is network-endian (it will go straight into the packet).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_confirm_addr(), inet_ifa_byprefix(), ip_dev_find(), inet_make_mask() and
inet_ifa_match() annotated, along with inferred net-endian variables
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifa_local, ifa_address, ifa_mask, ifa_broadcast and ifa_anycast are
net-endian. Annotated them and variables that are inferred to be
net-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
these are passed net-endian; use be32 netlink accessors
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
annotated arguments and inferred net-endian variables in callers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
argument and return value are net-endian. Annotated function and inferred
net-endian variables in callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
annotated address arguments (port number left alone for now); ditto
for inferred net-endian variables in callers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first 4 arguments of ip_rt_redirect() are net-endian. Annotated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() takes net-endian source and destination address.
* Annotated as such.
* arguments of its invocations annotated where needed.
* local helpers getting the same values passed to by it (ip_route_input_mc(),
ip_route_input_slow(), ip_handle_martian_source(), ip_mkroute_input(),
ip_mkroute_input_def(), __mkroute_input()) annotated
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix cut/paste error in TCPPROBE help text.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A while ago Ingo patched tcp_v4_rcv on net/ipv4/tcp_ipv4.c to use
bh_lock_sock_nested and silence a lock validator warning. This fixed
it for IPv4, but recently I saw a report of the same warning on IPv6.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (48 commits)
[PATCH] bonding: update version number
[PATCH] git-netdev-all: pc300_tty build fix
[PATCH] Make PC300 WAN driver compile again
[PATCH] Modularize generic HDLC
[PATCH] more s2io __iomem annotations
[PATCH] restore __iomem annotations in e1000
[PATCH] 64bit bugs in s2io
[PATCH] bonding: Fix primary selection error at enslavement time
[PATCH] bonding: Don't mangle LACPDUs
[PATCH] bonding: Validate probe replies in ARP monitor
[PATCH] bonding: Don't release slaves when master is admin down
[PATCH] bonding: Add priv_flag to avoid event mishandling
[PATCH] bonding: Handle large hard_header_len
[PATCH] bonding: Remove unneeded NULL test
[PATCH] bonding: Format fix in seq_printf call
[PATCH] bonding: Convert delay value from s16 to int
[PATCH] bonding: Allow bonding to enslave a 10 Gig adapter
Delete unused drivers/net/gt64240eth.h
[PATCH] skge: fiber support
[PATCH] fix possible NULL ptr deref in forcedeth
...
This eliminates the i_blksize field from struct inode. Filesystems that want
to provide a per-inode st_blksize can do so by providing their own getattr
routine instead of using the generic_fillattr() function.
Note that some filesystems were providing pretty much random (and incorrect)
values for i_blksize.
[bunk@stusta.de: cleanup]
[akpm@osdl.org: generic_fillattr() fix]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Rougly half of callers already do it by not checking return value
* Code in drivers/acpi/osl.c does the following to be sure:
(void)kmem_cache_destroy(cache);
* Those who check it printk something, however, slab_error already printed
the name of failed cache.
* XFS BUGs on failed kmem_cache_destroy which is not the decision
low-level filesystem driver should make. Converted to ignore.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that all of the supporting pieces of NetLabel have a home at SourceForge
update the Kconfig help text and add an entry to the MAINTAINERS file.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the suggestion of Thomas Graf, rewrite NetLabel's use of Netlink attributes
to better follow the common Netlink attribute usage.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the suggestion of Thomas Graf, rewrite NetLabel's use of Netlink attributes
to better follow the common Netlink attribute usage.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CIPSOv4 cache traversal routines are triggered both the userspace events
(cache invalidation due to DOI removal or updated SELinux policy) and network
packet processing events. As a result there is a problem with the existing
CIPSOv4 cache spinlocks as they are not bottom-half/softirq safe. This patch
converts the CIPSOv4 cache spin_[un]lock() calls into spin_[un]lock_bh() calls
to address this problem.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem where NetLabel would always set the value of
sk_security_struct->peer_sid in selinux_netlbl_sock_graft() to the context of
the socket, causing problems when users would query the context of the
connection. This patch fixes this so that the value in
sk_security_struct->peer_sid is only set when the connection is NetLabel based,
otherwise the value is untouched.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch to make bcm43xx-softmac be compatible with the revised SSID
length of WE-21.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is version 21 of the Wireless Extensions. Changelog :
o finishes migrating the ESSID API (remove the +1)
o netdev->get_wireless_stats is no more
o long/short retry
This is a redacted version of a patch originally submitted by Jean
Tourrilhes. I removed most of the additions, in order to minimize
future support requirements for nl80211 (or other WE successor).
CC: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change default congestion control used from BIC to the newer CUBIC
which it the successor to BIC but has better properties over long delay links.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change how default TCP congestion control is chosen. Don't just use
last installed module, instead allow selection during configuration,
and make sure and use the default regardless of load order.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds DCCP probing shamelessly ripped off from TCP probes by Stephen
Hemminger.
I've put in here support for further CCID3 variables as well.
Andrea/Arnaldo might look to extend for CCID2.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
With constants for CCID numbers this now uses them in some places.
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This has been discussed on dccp@vger and removes the necessity for applications
to supply service codes in each and every case.
If an application does not want to provide a service code, that's fine, it will
be given 0. Otherwise, service codes can be set via socket options as before.
This patch has been tested using various client/server configurations
(including listening on multiple service codes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (74 commits)
NFS: unmark NFS direct I/O as experimental
NFS: add comments clarifying the use of nfs_post_op_update()
NFSv4: rpc_mkpipe creating socket inodes w/out sk buffers
NFS: Use SEEK_END instead of hardcoded value
NFSv4: When mounting with a port=0 argument, substitute port=2049
NFSv4: Poll more aggressively when handling NFS4ERR_DELAY
NFSv4: Handle the condition NFS4ERR_FILE_OPEN
NFSv4: Retry lease recovery if it failed during a synchronous operation.
NFS: Don't invalidate the symlink we just stuffed into the cache
NFS: Make read() return an ESTALE if the file has been deleted
NFSv4: It's perfectly legal for clp to be NULL here....
NFS: nfs_lookup - don't hash dentry when optimising away the lookup
SUNRPC: Fix Oops in pmap_getport_done
SUNRPC: Add refcounting to the struct rpc_xprt
SUNRPC: Clean up soft task error handling
SUNRPC: Handle ENETUNREACH, EHOSTUNREACH and EHOSTDOWN socket errors
SUNRPC: rpc_delay() should not clobber the rpc_task->tk_status
Fix a referral error Oops
NFS: NFS_ROOT should use the new rpc_create API
NFS: Fix up compiler warnings on 64-bit platforms in client.c
...
Manually resolved conflict in net/sunrpc/xprtsock.c
This patch stop rpc_mkpipe from create S_IFSOCK nodes what don't
have associated sk buffers attached (which causes SELinux to oops
during NFSv4 mounts). Instead the S_IFIFO mode bit is set which
probably make more sense and seems to work just fine during
my connectathon and fsx testing...
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There is no guarantee that the parent task still exists when we exit from
the portmapper. Save the xprt instead.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In a subsequent patch, this will allow the portmapper to take a reference
to the rpc_xprt for which it is updating the port number, fixing an Oops.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
- Ensure that the task aborts the RPC call only when it has actually timed out.
- Ensure that req->rq_majortimeo is initialised correctly.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In case of any of the above errors occuring, delay for 3 seconds, then
handle as if it were a timeout error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch is optional.
It has been suggested that the RPC client internal functions used by upper
layer protocols (such as NFS) be exported via EXPORT_SYMBOL_GPL. This
patch does that.
Test plan:
Compile kernel with CONFIG_NFS enabled as a module.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The two function call API for creating a new RPC client is now obsolete.
Remove it.
Also, remove an unnecessary check to see whether the caller is capable of
using privileged network services. The kernel RPC client always uses a
privileged ephemeral port by default; callers are responsible for checking
the authority of users to make use of any RPC service, or for specifying
that a nonprivileged port is acceptable.
Test plan:
Repeated runs of Connectathon locking suite. Check network trace to ensure
correctness of NLM requests and replies.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Replace xprt_create_proto/rpc_create_client calls in pmap_clnt.c with new
rpc_create() API.
Test plan:
Repeated runs of Connectathon locking suite. Check network trace for
proper PMAP calls and replies.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare for more generic transport endpoint handling needed by transports
that might use different forms of addressing, such as IPv6.
Introduce a single function call to replace the two-call
xprt_create_proto/rpc_create_client API. Define a new rpc_create_args
structure that allows callers to pass in remote endpoint addresses of
varying length.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
IPv6 addresses are big (128 bytes). Now that no RPC client consumers treat
the addr field in rpc_xprt structs as an opaque, and access it only via the
API calls, we can safely widen the field in the rpc_xprt struct to
accomodate larger addresses.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hide the details of how the RPC client stores remote peer addresses from
the RPC pipefs implementation.
Test plan:
Connectathon with Kerberos 5 authentication.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Provide an API for formatting the remote peer address for printing without
exposing its internal structure. The address could be dynamic, so we
support a function call to get the address rather than reading it straight
out of a structure.
Test-plan:
Destructive testing (unplugging the network temporarily). Probably need
to rig a server where certain services aren't running, or that returns an
error for some typical operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a new method to the transport switch API to provide a way to convert
the opaque contents of xprt->addr to a human-readable string.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
include/linux/sunrpc/clnt.h already includes include/linux/sunrpc/xprt.h.
We can remove xprt.h from source files that already include clnt.h.
Likewise include/linux/sunrpc/timer.h.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hide the details of how the RPC client stores remote peer addresses from
the RPC portmapper.
Test plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP. NFSv2/3 and NFSv4 mounting should be carefully checked.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Provide an API for retrieving the remote peer address without allowing
direct access to the rpc_xprt struct.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a clean transport switch API for plugging in different types of
rpcbind mechanisms. For instance, rpcbind can cleanly replace the
existing portmapper client, or a transport can choose to implement RPC
binding any way it likes.
Test plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP. NFSv2/3 and NFSv4 mounting should be carefully checked.
Probably need to rig a server where certain services aren't running, or
that returns an error for some typical operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The previous patches removed the last user of RPC child tasks, so we can
remove support for child tasks from net/sunrpc/sched.c now.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add comments for external functions, use modern function definition style,
and fix up dprintk formatting.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Move connection and bind state that was maintained in the rpc_clnt
structure to the rpc_xprt structure. This will allow the creation of
a clean API for plugging in different types of bind mechanisms.
This brings improvements such as the elimination of a single spin lock to
control serialization for all in-kernel RPC binding. A set of per-xprt
bitops is used to serialize tasks during RPC binding, just like it now
works for making RPC transport connections.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP. NFSv2/3 and NFSv4 mounting should be carefully checked.
Probably need to rig a server where certain services aren't running, or
that returns an error for some typical operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hide the contents and format of xprt->addr by eliminating direct uses
of the xprt->addr.sin_port field. This change is required to support
alternate RPC host address formats (eg IPv6).
Test-plan:
Destructive testing (unplugging the network temporarily). Repeated runs of
Connectathon locking suite with UDP and TCP.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
IFA_F_HOMEADDRESS is introduced for Mobile IPv6 Home Addresses on
Mobile Node.
The IFA_F_HOMEADDRESS flag should be set for Mobile IPv6 Home
Addresses for 2 purposes. 1) We need to check this on receipt of
Type 2 Routing Header (RFC3775 Secion 6.4), 2) We prefer Home
Address(es) in source address selection (RFC3484 Section 5 Rule 4).
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFA_F_NODAD flag, similar to IN6_IFF_NODAD in BSDs, is introduced
to skip DAD.
This flag should be set to Mobile IPv6 Home Address(es) on Mobile
Node because DAD would fail if we should perform DAD; our Home Agent
protects our Home Address(es).
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did not send appropriate IsRouter flag if the forwarding setting is
positive even value. Let's give 1/0 value to ndisc_send_na().
Also, existing users of ndisc_send_na() give 0/1 to override,
we can omit redundant operation in that function.
Bug hinted by Nicolas Dichtel <nicolas.dichtel@6wind.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not always need proxy NDP functionality even we
enable forwarding.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have sent NA with router flag from the node-wide forwarding
configuration. This is not appropriate for proxy NA, and it should be
set according to each proxy entry's configuration.
This is used by Mobile IPv6 home agent to support physical home link
in acting as a proxy router for mobile node which is not a router,
for example.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This aims at proxying router not updating neighbor cache entry for proxied
address when it receives NA because either the proxied node is off link or
it has already sent a NA to the proxied router.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Proxying router can't forward traffic sent to link-local address, so signal
the sender and discard the packet. This behavior is clarified by Mobile IPv6
specification (RFC3775) but might be required for all proxying router.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
It is required to respond to NDP messages sent directly to the "target"
unicast address. Proxying node (router) is required to handle such
messages. To achieve this, check if the packet in forwarding patch is
NDP message.
With this patch, the proxy neighbor entries are always looked up in
forwarding path. We may want to optimize further.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
When the master PPTP connection times out while still having unfullfilled
expectations (and a GRE keymap entry) associated with it, the keymap entry
is not destroyed.
Add a destroy callback to struct ip_conntrack_helper and use it to destroy
PPTP siblings when the master is destroyed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When destroying the GRE expectations without having seen the GRE connection
the keymap entry is not freed, leading to a memory leak and, in case of
a following call within the same session, failure during expectation setup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrectly used message types and call IDs:
- PPTP_IN_CALL_REQUEST (PAC->PNS) contains a PptpInCallRequest (icreq)
message and the PAC call ID
- PPTP_IN_CALL_REPLY (PNS->PAC) contains a PptpInCallReply (icack)
message and the PNS call ID
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For rejected calls the state is set to PPTP_CALL_NONE even for non-matching
call ids.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also make sure not to hand packets received in an invalid state to the
NAT helper since it will mangle the packet with invalid data.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also make sure not to pass undersized messages to the NAT helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated expectation handling in the NAT helper and simplify
the remains in the conntrack helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just the values are needed, not the memory locations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a few header definitions to match RFC2637. Most importantly the
PptpOutCallRequest header included an invalid padding field and a
size check was disabled because of this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calculated sequence numbers are not used for anything.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call ID in reply packets is never changed, remove the code.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conntrack structure contains the call ID in host byte order for no
reason, get rid of back and forth conversions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the xt_compat_match/xt_compat_target into smaller type-safe functions
performing just one operation. Handle all alignment and size-related
conversions centrally in these function instead of requiring each module to
implement a full-blown conversion function. Replace ->compat callback by
->compat_from_user and ->compat_to_user callbacks, responsible for
converting just a single private structure.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparse "defined twice" warning
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression introduced by the incremental checksum patches.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SMP environments the maximum number of conntracks can be overpassed
under heavy stress situations due to an existing race condition.
CPU A CPU B
atomic_read() ...
early_drop() ...
... atomic_read()
allocate conntrack allocate conntrack
atomic_inc() atomic_inc()
This patch moves the counter incrementation before the early drop stage.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the bits to dump the conntrack table and the ones to dump and
zero counters in a single piece of code. This patch does not change
the default behaviour if accounting is not enabled.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While standard_target has target->me == NULL, module_put() should be
called for it as for others, because there were try_module_get() before.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that IPv6 supports policy routing we need to reroute in NF_IP6_LOCAL_OUT
when the mark value changes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limit match reinitializes its state whenever the ruleset changes,
which means it will forget about previously used credits.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove debugging cruft
- remove printk for reallocation failures
- remove unused addition
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix whitespace error
- break lines at 80 characters
- reformat some expressions to be more readable
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix some whitespace errors and use the NAT bits instead of deriving
the state manually.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill listhelp.h and use the list.h functions instead.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of ipip and ip_gre ICMP error relaying is b0rken; it accesses
8bit field + 3 reserved octets as host-endian 32bit, does comparison,
subtraction and stuffs the result back. That breaks on big-endian.
Fixed, made endian-clean.
[ Note that this effected code is permanently commented out with
and ifdef, so this error couldn't actually cause problems for
anyone. -DaveM ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce methods which manipulate interesting congestion control
state such as pipe and rtt estimate. This is useful for people
wishing to monitor the variables of CCID and instrument the code
[perhaps using Kprobes]. Personally, I am a fan of
encapsulation---that justifies this change =D.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple losses occur in one RTT, the window should be halved
only once [a single "congestion event"]. This is now implemented,
although not perfectly. Slightly changed the interface for changing
the cwnd: pass hctx instead of dp. This is required in order to allow
for change_cwnd to be called from _init().
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate more sequence state on demand. Each time a packet is sent
out by CCID2, a record of it needs to be kept. This list of records
grows proportionally to cwnd. Previously, the length of this list was
hardcored and therefore the cwnd could only grow to this value (of
128). Now, records are allocated on demand as necessary---cwnd may
grow as it wishes. The exceptional case of when memory is not
available is not handled gracefully. Perhaps, cwnd should be capped
at that point.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to choose whether or not to enable CCID2 debugging via
Kconfig.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If not enough cwnd is available, tell the sender to check again as
soon as possible. This will increase CPU utilization (polling
frequently for cwnd) but will improve network performance. That is,
the sender will need to wait less before detecting the increase of
cwnd. A better architecture would be for the CCID to call-back (or
dequeue) from DCCP when it is able to transmit traffic -- not the
other way around as it currently occurs.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the slow-start threshold to infinity. This way, upon connection
initiation, slow-start will be exited only upon a packet loss. This patch will
allow connections to quickly gain speed.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiffies are now handled correctly (I hope) in CCID2. If they wrap, no
problem.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of unused variables in ackvector state.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the way state is masked out. DCCP_ACKVEC_STATE_NOT_RECEIVED is
defined as appears in the packet, therefore bit shifting is not
required. This fix allows CCID2 to correctly detect losses.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ackvector length calculation upon receiving an "ack-of-ack". This
patch avoids the ackvector from growing too large which causes it to
not be inserted into packets.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hashing SAs by source address breaks templates with wildcards as tunnel
source since the source address used for hashing/lookup is still 0/0.
Move source address lookup to xfrm_tmpl_resolve_one() so we can use the
real address in the lookup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not affect either mss-sized connections (obviously) or
connections controlled by Nagle (because there is only one small
segment in flight).
The idea is to record the fact that a small segment arrives on a
connection, where one small segment has already been received and
still not-ACKed. In this case ACK is forced after tcp_recvmsg() drains
receive buffer.
In other words, it is a "soft" each-2nd-segment ACK, which is enough
to preserve ACK clock even when ABC is enabled.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the following cleanups:
- make the following needlessly global function static:
- socket.c: sctp_apply_peer_addr_params()
- add proper prototypes for the several global functions in
include/net/sctp/sctp.h
Note that this fixes wrong prototypes for the following functions:
- sctp_snmp_proc_exit()
- sctp_eps_proc_exit()
- sctp_assocs_proc_exit()
The latter was spotted by the GNU C compiler and reported
by David Woodhouse.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iproute2 doesn't provide the NLM_F_CREATE flag when adding addresses,
it is assumed to be implied. The existing code issues a check on
said flag when the modify operation fails (likely due to ENOENT)
before continueing to create it, this leads to a hard to predict
result, therefore the NLM_F_CREATE check is removed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same behaviour as IPv4, using IFF_UP is a no-no anyway.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaces INET6_IFADDR_RTA_SPACE with a new function calculating
the total required message size for all address messages.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change some netfilter tunables to __read_mostly. Also fixed some
incorrect file reference comments while I was in there.
(this will be my last __read_mostly patch unless someone points out
something else that needs it)
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change some bridge sysctl tunables to __read_mostly.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additionaly exports the following information when providing
the list of registered generic netlink families:
- protocol version
- header size
- maximum number of attributes
- list of available operations including
- id
- flags
- avaiability of policy and doit/dumpit function
libnl HEAD provides a utility to read this new information:
0x0010 nlctrl version 1
hdrsize 0 maxattr 6
op GETFAMILY (0x03) [POLICY,DOIT,DUMPIT]
0x0011 NLBL_MGMT version 1
hdrsize 0 maxattr 0
op unknown (0x02) [DOIT]
op unknown (0x03) [DOIT]
....
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing a device by ifindex without including a IFLA_IFNAME
attribute, the ifname variable contains random garbage and is used
to change the device name.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that during the MIPv6 respin, some code which was originally
conditionally compiled around CONFIG_XFRM_ADVANCED was accidently left
in after the config option was removed.
This patch removes an extraneous pointer (xerr_idxp) which is no
longer needed.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose IPSEC modes output path to take an xfrm state as input param.
This makes it consistent with the input mode processing (which already
takes the xfrm state as a param).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function sk_filter() is called from tcp_v{4,6}_rcv() functions with arg
needlock = 0, while socket is not locked at that moment. In order to avoid
this and similar issues in the future, use rcu for sk->sk_filter field read
protection.
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
By passing a Linux-generated TSO packet straight back into Linux, Xen
becomes our first LRO user :) Unfortunately, there is at least one spot
in our stack that needs to be changed to cope with this.
The receive MSS estimate is computed from the raw packet size. This is
broken if the packet is GSO/LRO. Fortunately the real MSS can be found
in gso_size so we simply need to use that if it is non-zero.
Real LRO NICs should of course set the gso_size field in future.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typo introduced by myself which leads to freeing the skb
containing the netlink message when it should free the newly
allocated skb for the reply.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global struct simp_hash_info static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing include files to the NetLabel related header files.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Arnaldo Carvalho de Melo points out I should be using list_entry in case
the structure changes in future. Current code functions but is reliant
on position and requires type cast.
Noticed when doing this that I have one more variable than I needed so
removing that also.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NETFILTER_DEBUG is enabled, it shouldn't change the
actions of the filtering. The message about skb->dst being NULL
is commonly triggered by dhclient, so it is useless. Make sure all
messages end in newline.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do some simple optimization on the nf_bridge_pad() function
and don't use magic constants. Eliminate a double call and
the #ifdef'd code for CONFIG_BRIDGE_NETFILTER.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup and rearrangement for better style and clarity:
Split the function nf_bridge_maybe_copy_header into two pieces
Move copy portion out of line.
Use Ethernet header size macros.
Use header file to handle CONFIG_NETFILTER_BRIDGE differences
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/netfilter/xt_CONNMARK.c: In function 'target':
net/netfilter/xt_CONNMARK.c:59: warning: implicit declaration of
function 'nf_conntrack_event_cache'
The warning is due to the following .config:
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_CONNTRACK_MARK=y
# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
CONFIG_IP_NF_CONNTRACK_NETLINK=m
This change was introduced by:
http://www.kernel.org/git/?p=linux/kernel/git/davem/net-2.6.19.git;a=commit;h=76e4b41009b8a2e9dd246135cf43c7fe39553aa5
Proposed solution (based on the define in
include/net/netfilter/nf_conntrack_compat.h:
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6_pol_route_lookup(), when we finish backtracking at the
top-level root entry, we need to hold it.
Bug noticed by Mitsuru Chinen <CHINEN@jp.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts existing NLA_STRING attributes to use the new
validation features, saving a couple of temporary buffers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new attribute type NLA_NUL_STRING to support NUL
terminated strings. Attributes of this kind require to carry
a terminating NUL within the maximum specified in the policy.
The `old' NLA_STRING which is not required to be NUL terminated
is extended to provide means to specify a maximum length of the
string.
Aims at easing the pain with using nla_strlcpy() on temporary
buffers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also kills a warning while building ipv6:
net/ipv6/udp.c: In function ‘udp_v6_get_port’:
net/ipv6/udp.c:66: warning: passing argument 3 of ‘udp_get_port’ from incompatible pointer type
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates one common function which is called by
udp_v4_get_port() and udp_v6_get_port(). As a result,
* duplicated code is removed
* udp_port_rover and local port lookup can now be removed from udp.h
* further savings follow since the same function will be used by UDP-Litev4
and UDP-Litev6
In contrast to the patch sent in response to Yoshifujis comments
(fixed by this variant), the code below also removes the
EXPORT_SYMBOL(udp_port_rover), since udp_port_rover can now remain
local to net/ipv4/udp.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds transmit buffering to DCCP.
I have tested with CCID2/3 and with loss and rate limiting.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This shifts further sysctls into feat.h. No change in
functionality - shifting code only.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix mark comparison, also dump the mask to userspace when the mask is
zero, but the mark is not (in which case the mark is dumped, so the
mask is needed to make sense of it).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support masking the nfmark value before the search. The mask value is
global for all filters contained in one instance. It can only be set
when a new instance is created, all filters must specify the same mask.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fwmark masks. For compatibility a mask of 0xFFFFFFFF is used
when a mark value != 0 is sent without a mask.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a FRA_FWMASK attributes for fwmark masks. For compatibility a mask of
0xFFFFFFFF is used when a mark value != 0 is sent without a mask.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fwmark masks.
A mask of 0xFFFFFFFF is used when a mark value != 0 is sent without a mask.
Based on patch for net/ipv4/fib_rules.c by Patrick McHardy <kaber@trash.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should not be RTA_MAX+1 but FRA_MAX+1.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add missing nla_policy entry.
- type of fwmark is u32, not u8.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if we find an exact match in the hash table,
we must inspect the inexact list to look for a match
with a better priority.
Noticed by Masahide NAKAMURA <nakam@linux-ipv6.org>.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove redundant code. Pointed out by Brian Haley <brian.haley@hp.com>.
- Unify code paths with/without CONFIG_IPV6_MIP.
- Use NIP6_FMT for IPv6 address textual presentation.
- Fold long line. Pointed out by David Miller <davem@davemloft.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
First of all, if the xfrm_state only gets used for input
packets this entropy is a complete waste.
Secondly, it is often the case that a configuration loads
many rules (perhaps even dynamically) and they don't all
necessarily ever get used.
This get_random_bytes() call was showing up in the profiles
for xfrm_state inserts which is how I noticed this.
Signed-off-by: David S. Miller <davem@davemloft.net>
This idea is from Alexey Kuznetsov.
It is common for policies to be non-prefixed. And for
that case we can optimize lookups, insert, etc. quite
a bit.
For each direction, we have a dynamically sized policy
hash table for non-prefixed policies. We also have a
hash table on policy->index.
For prefixed policies, we have a list per-direction which
we will consult on lookups when a non-prefix hashtable
lookup fails.
This still isn't as efficient as I would like it. There
are four immediate problems:
1) Lots of excessive refcounting, which can be fixed just
like xfrm_state was
2) We do 2 hash probes on insert, one to look for dups and
one to allocate a unique policy->index. Althought I wonder
how much this matters since xfrm_state inserts do up to
3 hash probes and that seems to perform fine.
3) xfrm_policy_insert() is very complex because of the priority
ordering and entry replacement logic.
4) Lots of counter bumping, in addition to policy refcounts,
in the form of xfrm_policy_count[]. This is merely used
to let code path(s) know that some IPSEC rules exist. So
this count is indexed per-direction, maybe that is overkill.
Signed-off-by: David S. Miller <davem@davemloft.net>
The source address is always non-prefixed so we should use
it to help give entropy to the bydst hash.
Signed-off-by: David S. Miller <davem@davemloft.net>
The refcounting done for timers and hash table insertions
are just wasted cycles. We can eliminate all of this
refcounting because:
1) The implicit refcount when the xfrm_state object is active
will always be held while the object is in the hash tables.
We never kfree() the xfrm_state until long after we've made
sure that it has been unhashed.
2) Timers are even easier. Once we mark that x->km.state as
anything other than XFRM_STATE_VALID (__xfrm_state_delete
sets it to XFRM_STATE_DEAD), any timer that fires will
do nothing and return without rearming the timer.
Therefore we can defer the del_timer calls until when the
object is about to be freed up during GC. We have to use
del_timer_sync() and defer it to GC because we can't do
a del_timer_sync() while holding x->lock which all callers
of __xfrm_state_delete hold.
This makes SA changes even more light-weight.
Signed-off-by: David S. Miller <davem@davemloft.net>
Just let GC and other normal mechanisms take care of getting
rid of DST cache references to deleted xfrm_state objects
instead of walking all the policy bundles.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, simply set all potentially aliasing existing xfrm_state
objects to have the current generation counter value.
This will make routes get relooked up the next time an existing
route mentioning these aliased xfrm_state objects gets used,
via xfrm_dst_check().
Signed-off-by: David S. Miller <davem@davemloft.net>
Each xfrm_state inserted gets a new generation counter
value. When a bundle is created, the xfrm_dst objects
get the current generation counter of the xfrm_state
they will attach to at dst->xfrm.
xfrm_bundle_ok() will return false if it sees an
xfrm_dst with a generation count different from the
generation count of the xfrm_state that dst points to.
This provides a facility by which to passively and
cheaply invalidate cached IPSEC routes during SA
database changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The grow algorithm is simple, we grow if:
1) we see a hash chain collision at insert, and
2) we haven't hit the hash size limit (currently 1*1024*1024 slots), and
3) the number of xfrm_state objects is > the current hash mask
All of this needs some tweaking.
Remove __initdata from "hashdist" so we can use it safely at run time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Support Mobile IPv6 extension headers sorting for two transformation policies.
Mobile IPv6 extension headers should be placed after IPsec
transport mode, but before transport AH when outbound.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sort functions to combine templates/states for IPsec.
Think of outbound transformation order we should be careful with transport AH
which must be the last of all transport ones.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sub policy can be used through netlink socket.
PF_KEY uses main only and it is TODO to support sub.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under two transformation policies it is required to merge them.
This is a platform to sort state for outbound and templates
for inbound respectively.
It will be used when Mobile IPv6 and IPsec are used at the same time.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
