First control messages to the stick timeouts very often due to probable
hw bug. Repeat first message few times if it fails as workaround.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bug causes 2nd FE MPEG TS buffer size to be zero and therefore no picture
when 2nd FE was enabled. Configure correct buffer size also for 2nd FE.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch adds support for a new version of the
Terratec Cinergy DT USB XS Diversity Dual DVB-T TV tuner stick.
The USB ID of the new stick is 0ccd:0081.
The hardware of the stick has changed, when compared to the first version of
this stick, but it still uses quite standard components, so that only minor
changes are needed to the sources.
The patch has been successfully tested with hotplugging the device and then
2 x tzap and 2 x mplayer, to watch two different TV programs simultaneously.
The stick works with both, the old and new firmwares:
- dvb-usb-dib0700-1.10.fw and
- dvb-usb-dib0700-1.20.fw
Signed-off-by: Nicolas Fournier <nicolasfournier@yahoo.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Concurrent access to a single DVB CA 50221 interface slot is generally
discouraged. The underlying drivers (budget-av, budget-ci) do not implement
proper locking and thus two transactions could (and do) interfere with on
another.
This fixes the following problems seen by others and myself:
- sudden i/o errors when writing to the ci device which usually would
result in an undefined state of the hw and require a software restart
- errors about the CAM trying to send a buffer larger than the agreed size
usually also resulting in an undefined state of the hw
Due the to design of the DVB CA 50221 driver, implementing the locks in the
underlying drivers would not be enough and still leave some race conditions,
even though they were harder to trigger.
Signed-off-by: Matthias Dahl <devel@mortal-soul.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for dvb-t for the following dibcom based card:
Terratec Cinergy T Express (USB-ID: 0ccd:0062)
Signed-off-by: Yusuf Altin <yusuf.altin@t-online.de>
Signed-off-by: Albert Comerma <albert.comerma@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use internal network_device_stats that exist in network device and
net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Randy Dunlap <randy.dunlap@oracle.com>:
With CONFIG_INPUT=m and CONFIG_DVB_DM1105=y:
drivers/built-in.o: In function `input_sync':
dm1105.c:(.text+0x120c33): undefined reference to `input_event'
drivers/built-in.o: In function `dm1105_emit_key':
dm1105.c:(.text+0x120c6c): undefined reference to `input_event'
dm1105.c:(.text+0x120c82): undefined reference to `input_event'
dm1105.c:(.text+0x120cb2): undefined reference to `input_event'
dm1105.c:(.text+0x120cd1): undefined reference to `input_event'
drivers/built-in.o: In function `dm1105_ir_init':
(.devinit.text+0xd8ae): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `dm1105_ir_init':
(.devinit.text+0xd9f6): undefined reference to `input_register_device'
drivers/built-in.o: In function `dm1105_ir_init':
(.devinit.text+0xda09): undefined reference to `input_free_device'
drivers/built-in.o: In function `dm1105_ir_exit':
(.devexit.text+0xcde): undefined reference to `input_unregister_device'
This is due to the lack of a dependency between dm1105 and CONFIG_INPUT
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee.c:44:5: warning: symbol 'dvb_usb_anysee_delsys' was not declared. Should it be static?
cx24116.c:378:3: warning: symbol 'CX24116_MODFEC_MODES' was not declared. Should it be static?
stb0899_algo.c:57:5: warning: symbol 'stb0899_get_srate' was not declared. Should it be static?
stb0899_algo.c:766:6: warning: symbol 'Log2Int' was not declared. Should it be static?
stb0899_drv.c:137:20: warning: symbol 'stb0899_quant_tab' was not declared. Should it be static?
stb0899_drv.c:180:20: warning: symbol 'stb0899_est_tab' was not declared. Should it be static?
stb0899_drv.c:220:5: warning: symbol '_stb0899_read_reg' was not declared. Should it be static?
budget-ci.c:1348:23: warning: symbol 'tt3200_stb6100_config' was not declared. Should it be static?
/home/v4l/master/v4l/cx25840-core.c:190:6: warning: symbol 'cx25840_work_handler' was not declared. Should it be static?
/home/v4l/master/v4l/m5602_s5k83a.c:116:6: warning: symbol 's5k83a_dump_registers' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/dvb_frontend.c:838:19: warning: symbol 'dtv_cmds' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1035:6: warning: symbol 'dtv_property_dump' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1066:5: warning: symbol 'is_legacy_delivery_system' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1080:6: warning: symbol 'dtv_property_cache_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1132:6: warning: symbol 'dtv_property_legacy_params_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1187:6: warning: symbol 'dtv_property_adv_params_sync' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1222:6: warning: symbol 'dtv_property_cache_submit' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1253:5: warning: symbol 'dtv_property_process_get' was not declared. Should it be static?
/home/v4l/master/v4l/dvb_frontend.c:1362:5: warning: symbol 'dtv_property_process_set' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness. This opens a race condition between the
open handler and module unloading.
A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.
This change checks the fops_get() return value and returns -ENODEV if NULL.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The GPIO logic for LNA control on the Tiger r2 devices was inverted.
This patch corrects the problem.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Report to userspace that cx24116 and stv0899 drivers support DVB-S2.
Signed-off by: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix I2C bridge error in zl10353 if no tunner attached to internal I2C
bus of zl10353 chip.
When set enable bridge from internal I2C bus to the main I2C bus
(saa7134) the main I2C bus stopped very hardly. No any communication. In
our next board we solder additional resistors to internal I2C bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since ttusb_dec.c relies on pci_alloc_consistent and
pci_free_consistent, make it depend on PCI in Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since dvb-ttusb-budget.c relies on pci_alloc_consistent and
pci_free_consistent, make it depend on PCI in Kconfig.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since internal to v4l2 the ioctl prototype is the same regardless of it
being called through .ioctl or .unlocked_ioctl, we need to convert it all
to the long return type of unlocked_ioctl.
Thanks to Jean-Francois Moine for posting an initial patch for this and
thus bringing it to our attention.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a struct v4l2_file_operations for v4l2 drivers.
Remove the unnecessary inode argument.
Move compat32 handling (and llseek) into the v4l2-dev core: this is now
handled in the v4l2 core and no longer in the drivers themselves.
Note that this changeset reverts an earlier patch that changed the return
type of__video_ioctl2 from int to long. This change will be reinstated
later in a much improved version.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: clean up
RW_LOCK_UNLOCKED is deprecated. This patch replaces it with the
__RW_LOCK_UNLOCKED(lock) macro. This change was a little trickier than
others due to the macro being used in another macro that fills an array.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’:
drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’:
drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’:
drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized
By looking at the function, altrough very unlikely, this might
eventually be true if num = 0. So, better to fix the warning by
initializing with ret = 0.
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the initialization of the URB list for a DVB-USB device to prevent
problems on certain platforms (MIPS).
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p.h defines a few extern symbols when CONFIG_DVB_DIB7000P is not set. since the
header is used on more than one driver, this causes symbol duplication, as pointed by
Ingo Molnar <mingo@elte.hu>:
drivers/media/dvb/built-in.o: In function `dib7000p_set_gpio':
(.text+0x3f242): multiple definition of `dib7000p_set_gpio'
drivers/media/video/built-in.o:(.text+0xb8c1e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_i2c_enumeration':
(.text+0x3f282): multiple definition of `dib7000p_i2c_enumeration'
drivers/media/video/built-in.o:(.text+0xb8c3e): first defined here
drivers/media/dvb/built-in.o: In function `dib7000p_set_wbd_ref':
(.text+0x3f1c1): multiple definition of `dib7000p_set_wbd_ref'
drivers/media/video/built-in.o:(.text+0xb8bfe): first defined here
LD drivers/net/built-in.o
make[2]: *** [drivers/media/built-in.o] Error 1
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the gp8psk module to use the S2API.
It pretends to be DVB-S2 capable in order to allow the various
supported modulations (8PSK, QPSK-Turbo, etc), and keep software
compatibility with the S2API patches for Mythtv and VDR.
Signed-off by: Alan Nisota <alannisota@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been noticed that in HW tuning mode in cx24123.c that
a check is made to not alter the status var when in one shot
mode, a simpler solution is to not update here for all cards.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Delsys was missing when searching for FEC in table.
This fixes FEC lookup for DVB-S2 QPSK modulation.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Uwe Bugla pointed out that there are some more typos in some print-statements. Fixed.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a typo in cx24113.c.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed some minor coding style issues and some driver information
printed when using the driver on a board.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds support for the CX24113 DVB-S tuner driver and thus support for the Technisat Skystar2 revision 2.8.
The driver was created with the help of Technisat. Thank you very much.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power the LNA while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
incoming symbols and hence might run into problems at the very end of the
specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
running at 90MHz, raises lot of issues such as the need to recalculate
all of them , which is eventually very painful.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides USB suspend and hibernation support
for Siano's SMS chipset based USB device
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
