This is part of a patch from Marc Singer to allow r2 to be
passed to the kernel. Marc's original comments follow:
This revised R2 (atags pointer) patch incorporates comments from Nico
Pitre and Ben Dooks. It modifies the head.S files such that the R2
value set by the bootloader is conveyed to the kernel startup code.
The kernel head.S heuristically validates the pointer. It will set R2
to zero if it believes the pointer is invalid. Presently, it requires
that the ATAGS list reside in the first 16KiB of physical RAM.
Relaxing this contraint may be both desirable as well as tricky.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
If the low interrupt latency mode is enabled for the CPU (from ARMv6
onwards), the ldm/stm instructions are no longer atomic. An ldm instruction
restoring the sp and pc registers can be interrupted immediately after sp
was updated but before the pc. If this happens, the CPU restores the base
register to the value before the ldm instruction but if the base register
is not sp, the interrupt routine will corrupt the stack and the restarted
ldm instruction will load garbage.
Note that future ARM cores might always run in the low interrupt latency
mode.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Since ARM1176, the CPU ID format has changed and it will also be used for
future ARM architectures.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Kevin Hilman
This patch increase available DMA-consistent memory allocated by dma_coherent_alloc(). The default remains at 2M (defined in asm/memory.h) and each platform has the ability to override in asm/arch-foo/memory.h.
Signed-off-by: Kevin Hilman <kevin@hilman.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
#3244)
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the support for the Cogent CSB337 and CSB637 boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the support for Atmel's DK and EK boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Properly tabulate the clock table in arch/arm/mach-s3c2410/clock.c
and put the requisite commas on the end of the structs.
Fix the comment about clock enable and disable in the setup code
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
In working on adding 36-bit addressed supersection support to ioremap(),
I came to the conclusion that it would be far simpler to do so by just
splitting __ioremap() into a main external interface and adding an
__ioremap_pfn() function that takes a pfn + offset into the page that
__ioremap() can call. This way existing callers of __ioremap() won't have
to change their code and 36-bit systems will just call __ioremap_pfn()
and we will not have to deal with unsigned long long variables.
Note that __ioremap_pfn() should _NOT_ be called directly by drivers
but is reserved for use by arch_ioremap() implementations that map
32-bit resource regions into the real 36-bit address and then call
this new function.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from SAN People
Following changes were made to clock.c:
1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.
Otherwise it's the same as the previous patch.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove various things which were checking for gcc-1.x and gcc-2.x compilers.
From: Adrian Bunk <bunk@stusta.de>
Some documentation updates and removes some code paths for gcc < 3.2.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the rtc_interrupt() prototype to rtc.h and removes the
prototypes from C files.
It also renames static rtc_interrupt() functions in
arch/arm/mach-integrator/time.c and arch/sh64/kernel/time.c to avoid compile
problems.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Gortmaker <p_gortmaker@yahoo.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ds1620 module is using gpio_read symbol, so works only if "built-in" symbol
needs to be exported from the kernel image
Signed-off-by: Woody Suwalski <woodys@xandros.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
at least 2.6.10
- interest seems to have dried up around March 2003.
Therefore, remove EPXA10DB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Fix a gcc4 build error (incomplete element type) in the pxa SharpSL
PM code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for arm arch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Jared Hulbert
The following patch changes the bus arbiter controller settings
for the Intel PXA27x Application Processor Family. Up to 5%
better video performance. It parks the bus on the core while not
in use and sets the arbitration for other bus items. The patch
only applies changes to the Intel Mainstone development platform.
This patch is not compatible with preproduction Intel PXA27x
silicon.
This patch is based on the Intel Linux Preview Kit released to the
public on 25 Feb. 2005 found at
ftp://ftp.arm.linux.org.uk/pub/linux/arm/people/xscale/mainstone/02-25-2005/.
Signed-off-by: Justin A Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
The expansion bus on the IXP46x NPU can be configured for either 32MiB or
16MiB windows and changing the configuration causes the base address for
each chip select for each region to change. Because of this, we cannot
hardcode the physical base as we currently do. This patch checks the
expansion bus configuration registers at runtime to determine the
appropriate window size. Note that this requires that the bootloader
already configured the device sizes appropriately, but I feel that is
valid assumption to make as the bootloader must configure and access
the flash window, the output display (LCD, LEDs, etc) window, and
other expansion bus devices.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
Convert old-style serial devices to platform devices so that printk's are visible during the boot process.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
- remove unnecessary mappings
- rename mx1ads_device to cs89x0_device, because
that's what it is
- fix io/irq resource for cs89x0 device
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
The SL-Cxx00 devices have a power control register in SCOOP that is
shared by both CF and MMC/SD card slots. The CF reset code was resetting
this register leading to various lockups as the MMC power was suddenly
lost. This patch handles the CPR register in a more sensitive manner.
It also removes some unneeded collie specific calls as the reset code
handles this.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
ARM doesn't use ACPI so ARM's apm implementation has no need to depend
on PM_LEGACY. This patch removes that dependency.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch moves a large chunk of the sharpsl_pm driver to
arch/arm/common so that it can be reused on other devices such as the
SL-5500 (collie). It also abstracts some functions from the core into
the machine and platform specific parts of the driver to aid reuse.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add platform code to enable the ohci device on the pxa27x based
Sharp Zaurus Cxx00 devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The first of these changes s/hotplug/uevent/ was needed to
compile sn2_defconfig (ia64/sn). The other three files
changed are blind changes of all remaining bus_type.hotplug
references I could find to bus_type.uevent.
This patch attempts to finish similar changes made in the
gregkh-driver-kill-hotplug-word-from-driver-core Nov 22 patch.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Deepak Saxena
Add NAS 100d to machine build list and update to new 2.6.15 options.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
---
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
PAGE_SHIFT is undeclared in include/asm-arm/arch-ixp4xx/memory.h, identified by the following kernel compilation error:
CC [M] sound/core/memory.o
In file included from include/asm/memory.h:27,
from include/asm/io.h:28,
from sound/core/memory.c:24:
include/asm/arch/memory.h: In function `__arch_adjust_zones':
include/asm/arch/memory.h:28: error: `PAGE_SHIFT' undeclared (first use
in this function)
This patch replaces my previous attempt at fixing this problem (Patch 3214/1) and is based on the following feedback:
Russell King wrote:
> The error you see came up on SA1100. The best solution was to move
> the __arch_adjust_zones() function out of line. I suggest ixp4xx
> does the same.
I have moved the function out of line into arch/arm/mach-ixp4xx/common-pci.c as suggested.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch removes referneces to gpio_isr_line_clear() from the
NAS 100d platform implementation.
Depends on 3192/1 and 3215/1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
This patch adds support for a new arm/ixp4xx machine - the Iomega NAS 100d network attached storage product. The NAS100D is a consumer device containing a 266MHz Intel IXP420 processor, 16MB of flash, 64MB of RAM, a 160Gb internal IDE hard disk, and 802.11b/g wireless on an Atheros mini-PCI card.
Work on porting the latest 2.6.x kernel to this device is being done by
the NSLU2-Linux project (the same team who maintains the port to the
Linksys NSLU2 device). In particular, the majority of this patch was
authored by Alessandro Zummo, based on the work done for MACH_NSLU2
support by the NSLU2-Linux core team of developers.
MACH_NAS100D (as implemented by this patch) can be enabled in jumbo
ixp4xx kernels without any affect on the other machines supported by
that kernel.
This patch applies cleanly against 2.6.15-rc7 and should be trivial to
apply to later kernel versions. It does not depend upon any other
patches.
Modified files (and number of lines inserted):
arch/arm/mach-ixp4xx/Kconfig | 8
arch/arm/mach-ixp4xx/Makefile | 1
include/asm-arm/arch-ixp4xx/hardware.h | 1
include/asm-arm/arch-ixp4xx/irqs.h | 9
include/asm-arm/arch-ixp4xx/nas100d.h | 75
arch/arm/mach-ixp4xx/nas100d-pci.c | 77
arch/arm/mach-ixp4xx/nas100d-power.c | 69
arch/arm/mach-ixp4xx/nas100d-setup.c | 133
-- Rod Whitby (NSLU2-Linux project lead)
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Other than interrupt masking purposes, this API is only used when
configuring interrupt lines and this patch moves that functionality
directly into the ixp4xx_set_irq_type() implementation as board level
PCI code should not need to worry about those details.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we now only build arch/arm/kernel/dma.c on machine types
which set ISA_DMA_API, we don't need to define MAX_DMA_CHANNELS
to 0 to indicate this - this definition becomes superfluous.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ISA_DMA_API tells the rest of the kernel if the ISA DMA API is
available. Select this symbol only on machine types which make
use of the ISA DMA API.
Make building of arch/arm/kernel/dma.c depend on this symbol -
if a machine does not support the ISA DMA API, it's pointless
building this file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need to have DMA initialised at the same time as
interrupts. Move it to a core_initcall().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old __address element in struct scatterlist remained from older
kernels because the ARM DMA emulation code made use of it. Move
this field into struct dma_struct, and convert DMA emulation code
to setup a SG entry as required.
Also, convert DMA emulation code to use the new DMA API rather
than the PCI DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to optimise the bus_to_virt(virt_to_bus())
transformation in the ARM ISA DMA interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CLPS711x, EPXA10DB and Integrator contained a dma.c file which has never
been built. Remove these redundant files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/entry-armv.S has contained a comment suggesting
that asm/hardware.h and asm/arch/irqs.h should be moved into the
asm/arch/entry-macro.S include. So move the includes to these
two files as required.
Add missing includes (asm/hardware.h, asm/io.h) to asm/arch/system.h
includes which use those facilities, and remove asm/io.h from
kernel/process.c.
Remove other unnecessary includes from arch/arm/kernel, arch/arm/mm
and arch/arm/mach-footbridge.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are coding the kernel link address into the makefiles, which is
invisibly dependent on PAGE_OFFSET. If PAGE_OFFSET is changed, the
makefiles also need to be changed.
Make adjustments such that the makefiles encode just the offset from
PAGE_OFFSET for the kernel link address, and use PAGE_OFFSET in the
linker scripts directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Strictly speaking, the NPTL kernel helpers are required for pre ARMv6
only. They are available on ARMv6+ as well for obvious compatibility
reasons. However there are cases where extra memory barriers are needed
when using an SMP ARMv6 machine but not on pre-ARMv6.
This patch adds a memory barrier kernel helper that glibc can use as
needed for pre-ARMv6 binaries to be forward compatible with an SMP
kernel on ARMv6, as well as the necessary dmb instructions to the
cmpxchg helper.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than providing more wrappers for 6-arg syscalls, arrange for
them to be supported as standard. This just means that we always
store the 6th argument on the stack, rather than in the wrappers.
This means we eliminate the wrappers for:
* sys_futex
* sys_arm_fadvise64_64
* sys_mbind
* sys_ipc
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
Handle new EABI relocations when loading kernel modules. This is
necessary for CONFIG_AEABI kernels, and also for some broken
(since fixed) old ABI toolchains.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lothar Wassmann
The patch makes sure, that the ouptut functions of pins are restored
before restoring the Alternat Function settings, preventing pins from
being intermediately configured for undefined or unwanted alternate
functions.
Here is the original comment:
I've got a PXA270 system that uses GPIO80 as nCS4. This system did
hang on resume. Digging into the problem I found that the processor
stalled immediately when restoring the GAFR2_U register which restored
the alternate function for GPIO80. Since the GPDR registers were
restored after the GAFR registers, the offending GPIO was configured
as input at this point.
Thus the alternate function that was in effect after restoring the
GAFR was in fact the input function "MBREQ" instead of the output
function "nCS4". The "PXA27x Processor Family Developer's Manual"
(Footnote in Table 6-1 on page 6-3) states that:
"The MBREQ alternate function must not be enabled until the PSSR[RDH]
bit field is cleared. For more details, see Table 3-15, "PSSR Bit
Definitions" on page 3-71."
There is another note in the Developer's Manual (chapter 24.4.2
"GPIO operation as Alternate Function" on page 24-4)
stating that:
"Configuring a GPIO for an alternate function that is not defined for
it causes unpredictable results."
Since some GPIOs have no input function defined, and to prevent
inadvertedly programming the MBREQ function on some pin, the GAFR
registers should be restored after the GPDR registers have been
restored.
Additional provisions have to be made when the MBREQ function is
actually required. The corresponding GAFR bits should not be restored
with the regular GAFR restore, but must be set only after the PSSR
bits have been cleared.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nikola Valerjev
Single stepping an application using ptrace() fails over ARM instructions BX and BLX.
Steps to reproduce:
Compile and link the following files
main.c
-----
void foo();
int main() {
foo();
return 0;
}
foo.s
-----
.text
.globl foo
foo:
BX LR
Using ptrace() functionality, run to main(), and start singlestepping.
Singlestep over \"BX LR\" instruction won\'t transfer the control back
to main, but run the code to completion.
This problems seems to be in the function get_branch_address() in
arch/arm/kernel/ptrace.c. The function doesn\'t seem to recognize BX
and BLX instructions as branches. BX and BLX instructions can be used
to convert from ARM to Thumb mode if the target address has the low
bit set. However, they are also perfectly legal in the ARM only mode.
Although other things in the kernel seem to indicate that only ARM
mode is accepted (and not Thumb), many compilers will generate BX
and BLX instructions even when generating ARM only code.
Signed-off-by: Nikola Valerjev <nikola@ghs.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Akita requires inbuilt kernel i2c support for its GPIOs. Add this
requirement to Kconfig and update the defconfig to match.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a typo in the ARM IXDP425 setup definition that mistakenly tries
to use UART1's IRQ for UART2's traffic.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lazy flush_dcache_page() causes userspace instability on SMP
platforms, so disable it for now.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This updates the Zaurus defconfigs. Poodle gets merged into
corgi_defconfig and support for tosa and akita is enabled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add iWMMX Extentions for the pxa27x based Zaurus models and
fix a couple of minor mistakes in the PXA Kconfig file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We must not call TLB maintainence operations with interrupts disabled,
otherwise we risk a lockup in the SMP IPI code.
This means that consistent_free() can not be called from a context with
IRQs disabled. In addition, we must not hold the lock in consistent_free
when we call flush_tlb_kernel_range(). However, we must continue to
prevent consistent_alloc() from re-using the memory region until we've
finished tearing down the mapping and dealing with the TLB.
Therefore, leave the vm_region entry in the list, but mark it inactive
before dropping the lock and starting the tear-down process. After the
mapping has been torn down, re-acquire the lock and remove the entry
from the list.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't really need to check whether the machine type is Netwinder
or CATS before setting up the PCI IO mapping for debugging. This
allows us to eliminate asm/mach-types.h from head.S
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dirk Opfer
Fix an error in tosa.c after the platform device conversion.
Signed-off-by: Dirk Opfer <Dirk@Opfer-Online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
After delivering a signal (creating its stack frame) we must check for
additional pending unblocked signals before returning to userspace.
Otherwise signals may be delayed past the next syscall or reschedule.
Once that was fixed it became obvious that the ARM signal mask manipulation
was broken. It was a little bit broken before the recent SA_NODEFER
changes, and then very broken after them. We must block the requested
signals before starting the handler or the same signal can be delivered
again before the handler even gets a chance to run.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, later gcc versions error out when our get_user is passed
a const pointer, since we write to a temporary variable declared as
typeof(*(p)) which propagates the const-ness.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Document that the VMALLOC_END address must be aligned to 2MB since
it must align with a PGD boundary.
Allocate the vectors page early so that the flush_cache_all() later
will cause any dirty cache lines in the direct mapping will be safely
written back.
Move the flush_cache_all() to the second local_flush_cache_tlb() and
remove the now redundant first local_flush_cache_tlb().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "align" argument in ARMs __ioremap is unused and provides a
misleading expectation that it might do something. It doesn't.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, using PAGE_SHIFT in asm/arch/memory.h is unsafe, and we
can't include asm/page.h into this file because then we have a circular
dependency. Move the offending code to arch/arm/common/sa1111.c
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Minor changes, including add SysRq, selecting the DM9000
as a built-in driver, not as a module, and selecting the
framebuffer.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Make the use of , on the lsat entry structs consistenent
through arch/arm/mach-s3c2410/mach-bast.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we want new platforms to use debug-macro.S, make the decompressor
debugging method default to using this include file rather than having
new platforms add to an #if defined().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move __io_address to arch-realview/hardware.h, drop core.h from platsmp.c
and localtimer.c, and include asm/io.h where required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This avoids a BUG_ON with kref.c when SA1111 tries to register
a driver with an unregistered bus type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than defining our own PM option, use kernel/power/Kconfig.
This fixes build errors introduced by
bca73e4bf8
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Add a driver for the extra GPIOs found on the Sharp SL-C1000 (Akita).
These GPIOs are found on a Maxim MAX7310 I2C i/o expander chip. A
generic GPIO driver for the MAX7310 was attempted but this mini
driver is a much simpler and much more effective solution avoiding
several issues and complexity the generic driver had (as discussed
on LKML).
The platform device is required so the device parent can be set
correctly which ensures the device is one of the last to suspend
and first to resume. Whilst the i2c suspend/resume calls can be
influenced, nothing guarantees this is easlier/later than the
subsystems the gpios are used on which are all independent of i2c
(sound, irda, video/backlight etc.).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-Cxx00 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add a SharpSL PM device driver for the SL-C7x0 machines.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
