Software antenna tuning is broken because of an function
ordering problem during rt2x00link_tuner().
rt2x00link_precalculate_signal()
rt2x00leds_led_quality()
rt2x00lib_antenna_diversity()
rt2x00link_precalculate_signal() will reset the quality TX/RX counters,
however rt2x00lib_antenna_diversity() requires the RX counter to
see what RSSI value must be used for a particular antenna.
We can't change the ordering since rt2x00lib_antenna_diversity() might
reset other statistics which are needed by the function called earlier.
Move the reset of the quality TX/RX counters into a seperate function
and move the call to after rt2x00lib_antenna_diversity().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_activate_qos instead of iwl3945_activate_qos.
Patch does two things
1) Patch adds iwl_activate_qos in core library.
2) 3945 makes use of iwl_activate_qos.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch does following,
1) mac80211's shared data is now initialized in iwl3945_setup_mac.
2) Set the rfkill to right state after initialization
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for iwlagn:
- Have to free eeprom of version check fails - otherwise we end up with
memory leak.
- Include removal of workqueue (created in _setup_deferred_work) in error
handling.
for iwl3945:
- Fix a few places to jump to correct error handling.
- Reorganize error handling to match with code flow.
- Include iwl_free_channel_map as part of error handling.
- Include releasing eeprom as part of error handling.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
unify the set key flow with iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS, TSF maintains local clock counters at each station. Network
Synchronization follows a completely distributed scheme where beacon frames
are generated. Each station maintain its own TSF timestamp, extracted from
beacon timestamps they recieved. Following patch synchronize this beacon timestamp
with uCode.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
update API to support new numbering that is used for other newer devices.
5150 ucode has not been released yet, so the first released API will be v2.
For those who do have a v1 API the driver does have backward compatibility
support new value of REPLY_TX_POWER_DBM_CMD
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "mac80211/cfg80211: move iwrange handler to cfg80211", the
results for link quality from "iwlist scan" and "iwconfig" commands
have been very different. The results are now consistent.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported- and tested-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds SSB functionality to register a fallback SPROM image from the
architecture setup code.
Weird architectures exist that have half-assed SSB devices without SPROM attached to
their PCI busses. The architecture can register a fallback SPROM image that is
used if no SPROM is found on the SSB device.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the driver is unconditionally notified of beacon
interval. This is a problem in AP mode, because the driver has
to know that the beacon interval has actualy changed to recalculate
TBTT and reset the HW TSF. Fix this to make mac80211 notify the driver
only when the beacon interval has been reconfigured to a new value.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure we print out a warning when the index is out of bounds,
i.e. even on hw_rix == AR5K_MAX_RATES.
Also change to WARN and print text with the reported hw_rix.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incorrect Michael MIC key (RX, should have been TX) was set for the
group key in AP mode. This resulted in all broadcast frames triggering
Michael MIC errors and eventual TKIP countermeasures. The change here
sets the correct Michael MIC key based on whether the local end is the
authenticator (well, AP for now).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Tested-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Applying kernel janitors todos (reduce stack
footprint where possible) to airo wireless driver.
(Before 1124 bytes on i386, now 876)
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin can reach -1 after the loop, so 0 is still success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements get_tsf() of ieee80211_ops in the zd1211rw driver.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nohwcrypt=1 module parameter can now be used to disable hardware
crypto in ath9k. While the hardware acceleration handles most cases,
it may be useful to be able to force mac80211 software implementation
to be used for some tests, e.g., with virtual interface combinations
that may not yet be supported in the key cache configuration. In
addition, this allows management frame protection to be tested with
older hardware revisions.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As analyzed by Patrick McHardy, vlan needs to reset it's
netdev_ops pointer in it's ->init() function but this
leaves the compat method pointers stale.
Add a netdev_resync_ops() and call it from the vlan code.
Any other driver which changes ->netdev_ops after register_netdevice()
will need to call this new function after doing so too.
With help from Patrick McHardy.
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tmspci tokenring driver crashes on device initialization
because it requests its irq before initializing corresponding data
structures. Fix this by moving request_irq call to a safer place.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error count a per-NIC variable.
Reset this the count after an hour if it has not reached the critical value.
Set the critical value back to 5.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flushing queues we disable normal interrupt and event handling and
poll event queue 0 looking for flush completions. Unfortunately the
flush event polling loop fails to move past any other type of event.
This problem has not been observed in production hardware but appears to
be a possibility.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_del_adapter() leaves dangling pointers in the structure. If we
retry the NIC probe and pass the structure to i2c_add_adapter() again
it will lead to an oops unless we clear it first.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MAC switching fails, stop the port properly.
If PHY reinitialisation fails, clear the port_initialized flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A commit c1b56878fb "tc: policing requires
a rate estimator" introduced a test which invalidates previously working
configs, based on examples from iproute2: doc/actions/actions-general.
This is too rigorous: a rate estimator is needed only when police's
"avrate" option is used.
Reported-by: Joao Correia <joaomiguelcorreia@gmail.com>
Diagnosed-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6833c043f9 introduced the phy
auto-powerdown capability. While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices. However, the 5906 phy departs from the
usual design. This commit was interfering with the 5906's ability to
negotiate link against some switches. This patch corrects the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sctp_ctl_sock_init() to try IPv4 if IPv6 socket registration
fails. Required if the IPv6 module is loaded with "disable=1", else
SCTP will fail to load.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "disable" module parameter support to ipv6.ko by specifying
"disable=1" on module load. We just do the minimum of initializing
inetsw6[] so calls from other modules to inet6_register_protosw()
won't OOPs, then bail out. No IPv6 addresses or sockets can be
created as a result, and a reboot is required to enable IPv6.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (i-- > 0); i reaches -1 after the loop, so the test below is printed
one too early: 0 still means success.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (--worklimit >= 0); worklimit reaches -1 after the loop. In
3c589_cs.c this caused a warning not to be printed.
In 3c574_cs.c contrastingly, el3_rx() treats worklimit differently:
static int el3_rx(struct net_device *dev, int worklimit)
{
while (--worklimit >= 0) { ... }
return worklimit;
}
el3_rx() is only called by function el3_interrupt(): twice:
static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
int work_budget = max_interrupt_work;
while(...) {
if (...)
work_budget = el3_rx(dev, work_budget);
if (...)
work_budget = el3_rx(dev, work_budget);
if (--work_budget < 0) {
...
break;
}
}
}
The error path can occur 2 too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is possible to do just about everything with the arp table
from user space except treat an entry like you are using it. To that end
implement and a flag NTF_USE that when set in a netwlink update request
treats the neighbour table entry like the kernel does on the output path.
This allows user space applications to share the kernel's arp cache.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware is issuing events to the driver the events
must be removed from the queue. If the queue overflows, the
firmware will build and special event that captures those that
are lost.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This event will arrive at boot time or after an
MPI processor reset if the firmware failed to initialize.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This worker and it's supporting routines are used for
IDC 'inter-device-communication' events that require
an ACK mailbox command be sent to allow completion
of the request. These requests are originated by
another function wanting to change some common
port paramters. Typical example would be:
1) Change max TX/RX frame size allowed.
2) Change pause parameters.
3) Change loopback mode.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
