It's an unrelated PLL filtering control bit, leave it alone when
changing the CRTC-encoder binding.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This should fix eDP on certain laptops with 18-bit panels, we were rejecting
the panel's native mode due to thinking there was insufficient bandwidth
for it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On certain boards, there's BIOS scripts and memory timings that need to
be modified with the memclk. Just pass in the entire perflvl struct and
let the chipset-specific code decide what to do.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This isn't correct everywhere yet, but since we don't use the data yet
it's perfectly safe to push in, and the information we gain from logs
will help to fix the remaining issues.
v2 (Ben Skeggs <bskeggs@redhat.com>):
- fixed up formatting
- free parsed timing info on takedown
- switched timing table printout to debug loglevel
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just in case someone, somewhere, does something difficult. This also
removes one path that was different between fermi and non-fermi.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francesco Marella <fmarl@paranoici.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Used on nv17-nv28, they contain memory clocks and timings, only one of
the table entries can actually be used, depending on the RAMCFG
straps, and it's usually higher than the frequency programmed on boot
by the BIOS.
The memory timings listed in table version 0x1x are used to init the
0x12xx range but they aren't required for reclocking to work.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Build breakage:
drivers/built-in.o: In function `nouveau_acpi_edid':
(.text+0x13404e): undefined reference to `acpi_video_get_edid'
make: *** [.tmp_vmlinux1] Error 1
Introduced by:
a6ed76d7ff is the first bad commit
commit a6ed76d7ff
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon Jul 12 15:33:07 2010 +1000
drm/nouveau: support fetching LVDS EDID from ACPI
Based on a patch from Matthew Garrett.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
It doesn't seem to revert cleanly, but the problem lies in these
two config entries:
CONFIG_ACPI=y
CONFIG_ACPI_VIDEO=m
Adding a select for ACPI_VIDEO appears to be the best solution, and
is comparable to what is done in DRM_I915. Builds, boots, and appears to
work correctly.
Signed-off-by: Philip J. Turmel <philip@turmel.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently just hooked up to the already-existing nouveau_hw, which should
handle all relevant chipsets as well as we currently can.
This will likely be eventually split out and improved into chipset specific
code at a later point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will make nouveau_pm attempt to report the card's current performance
level both during bootup, and through sysfs.
This is a very initial implementation, and can be improved a *lot*
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This replaces all the pll_types definitions for ones that match the types
used in the tables in recent VBIOS versions.
get_pll_limits() will now accept either type or register value as input
across all limits table versions, and will store the actual register ID
that a PLL type refers to in the returned structure.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The rest of the connector code assumes we can kfree() the EDID pointer.
This causes things to blow up with the ACPI EDID pointer we get
passed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The most important part of this change is that we now instruct PFIFO to
drop all pending fetches, rather than attempting to skip a single dword
and hope that things would magically sort themselves out - they usually
don't, and we end up with PFIFO being completely hung.
This commit also adds somewhat more useful logging when these exceptions
occur.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More Apple brain damage, it fixes the modesetting failure on an eMac
G4 (fdo bug 29810).
Reported-by: Zoltan Varnagy <doi@freemail.hu>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Instead of emptying the caches to avoid a race with the PFIFO puller,
go straight ahead and try to recover from it when it happens. Also,
kill pfifo->cache_flush and tile->lock, we don't need them anymore.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes sure that RAMHT is cleared correctly on start up.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
FW seems to be broken on nv18, it causes random lockups and breaks
suspend/resume even with the blob.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This doesn't actually happen now, but there's a test case for an earlier
kernel where a GPU error is signalled on one of nv50's fake channels, and
the ramht lookup by the IRQ handler triggered an oops.
This adds a check for RAMHT's existance on a channel before looking up
an object handle.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Will be used at a later point when we plug in an alternative VRAM memory
manager for GeForce 8+ boards.
Based on pscnv code to do the same.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
They don't seem to do anything useful, and we really want to program
CRE_LCD if we aren't lucky enough to find the right CRTC binding
already set.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some boards the residual current DAC outputs can draw when they're
disconnected can be high enough to give a false load detection
positive (I've only seen it in the S-video luma output of some cards,
but just to be sure). The output line capacitance is limited and
sampling twice should fix it reliably.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Hopefully this one will be better able to cope with moving tiled buffers
around without getting them all scrambled as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nv2x CRTC FIFOs are as large as in nv3x (4kB it seems), and the FIFO
control registers have the same layout: we can make them share the
same implementation.
Previously we were using the nv1x code, but the calculated FIFO
watermarks are usually too low for nv2x and they cause horrible
scanout artifacts. They've gone unnoticed until now because we've been
leaving one of the bandwidth regs uninitialized (CRE 47, which
contains the most significant bits of FFLWM), so everything seemed to
work fine except in some cases after a cold boot, depending on the
memory bandwidth and pixel clocks used.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some nv4x cards (specifically, the ones that use an internal
PCIE->AGP bridge) the AGP controller state isn't preserved after a
suspend/resume cycle, and the AGP control registers have moved from
0x18xx to 0x100xx, so the FW check in nouveau_mem_reset_agp() doesn't
quite work. Check "dev->agp->mode" instead.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm device drivers currently allow seeking on the
character device but never care about the actual
file position.
When we change the default llseek operation to be
no_llseek, calling llseek on a drm device would
return an error condition, which is an API change.
Explicitly setting noop_llseek lets us keep the
current API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nv50: initialize ramht_refs list for faked 0 channel
drm/nouveau: Don't take struct_mutex around the pushbuf IOCTL.
drm/nouveau: Take fence spinlock before reading the last sequence.
We need it for PFIFO_INTR_CACHE_ERROR interrupt handling,
because nouveau_fifo_swmthd looks for matching gpuobj in
ramht_refs list.
It fixes kernel panic in nouveau_gpuobj_ref_find.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We don't need it and it can lead to lock order inversions with respect
to drm_global_mutex, potentially causing dead locks.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It fixes a race between the TTM delayed work queue and the GEM IOCTLs
(fdo bug 29583) uncovered by the BKL removal.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Every driver used the default implementation. Fold that one into
the only callsite and drop the callback.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers happily copy&pasted the default implementation without
checking whether this callback is used at all. It's not. Sigh.
Kill it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vgaarb: Wrap vga_(get|put) in CONFIG_VGA_ARB
drm/radeon/kms: add missing scratch update in dp_detect
drm/modes: Fix CVT-R modeline generation
drm: fix regression in drm locking since BKL removal.
drm/radeon/kms: remove stray radeon_i2c_destroy
drm: mm: fix range restricted allocations
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nouveau: drop drm_global_mutex before sleeping in submission path
drm: export drm_global_mutex for drivers to use
drm/nv20: Don't use pushbuf calls on the original nv20.
drm/nouveau: Fix TMDS on some DCB1.5 boards.
drm/nouveau: Fix backlight control on PPC machines with an internal TMDS panel.
drm/nv30: Apply modesetting to the correct slave encoder
drm/nouveau: Use a helper function to match PCI device/subsystem IDs.
drm/nv50: add dcb type 14 to enum to prevent compiler complaint
If we keep hold of the mutex here, the process which currently holds the
buffer object will never be able to release it, causing a deadlock.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The "return" command is buggy on the original nv20, it jumps back to
the caller address as expected, but it doesn't clear the subroutine
active bit making the subsequent pushbuf calls fail with a "stack"
overflow.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The TMDS output of an nv11 was being detected as LVDS, because it uses
DCB type 2 for TMDS instead of type 4.
Reported-by: Bertrand VIEILLE <Vieille.Bertrand@free.fr>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
