The sensor enum definition was not at the right place.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first VC0321 settings were done at webcam connection only. They must also
be done on resume after suspend.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bit 0x04 of the bridge register 02 (GPIO) is used for audio connection
in webcams containing the bridge SN9C105. This patch sets it correctly,
according to the presence of an audio device.
Tested-by: Kyle Baker <kyleabaker@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When there is an audio device, use a lower alternate setting.
This patch does not fix correctly all audio and bandwidth problems.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes possible race conditions in queue management with SMP:
when a frame was completed, the irq function tried to use the next frame
buffer. At this time, it was possible that the application on an other
processor updated the frame pointer, making the image to point to a bad
buffer.
The patch contains two main changes:
- the image transfer uses the queue indexes which are protected against
simultaneous memory access,
- the image pointer which is used for image concatenation is only set at
interrupt level.
Some subdrivers which used the image pointer have been updated.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem may occur with SMP:
- a frame is completed at interrupt level (in gspca_frame_add with
packet_type == LAST_PACKET,
- just after clearing the bit V4L2_BUF_FLAG_QUEUED and before setting
the bit V4L2_BUF_FLAG_DONE, on the other processor, the application
tries to requeue the same frame buffer,
- then, the qbuf function succeeds because ALL_FLAGS are not set.
The fix sets and resets the two flags in one instruction.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image pointer and its length are now in the main structure instead
of in the frame buffer. They are updated on application vidioc_qbuf and
in the URB interrupt function when ending an image.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 05/29/10 01:30, Jean-Francois Moine wrote:
> On Fri, 28 May 2010 13:03:28 -0400
> Amerigo Wang<amwang@redhat.com> wrote:
>
>> Subject: [PATCH 6/6] Remove obsolete zc0301 v4l driver
>>
>> Duplicate functionality with the gspca_zc3xx driver, zc0301 only
>> supports 2 USB-ID's (because it only supports a limited set of
>> sensors) wich are also supported by the gspca_zc3xx driver
>> (which supports 53 USB-ID's in total).
>
> You forgot to remove the conditionnal compilation in the gspca_zc3xx
> driver (USB_DEVICE(0x046d, 0x08ae) in gspca/zc3xx.c)
>
Right, thanks for pointing this out!
Attached is the updated patch, please use this one instead.
Thanks!
Duplicate functionality with the gspca_zc3xx driver, zc0301 only
supports 2 USB-ID's (because it only supports a limited set of
sensors) wich are also supported by the gspca_zc3xx driver
(which supports 53 USB-ID's in total).
Signed-off-by: Amerigo Wang <amwang@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add Genius iSlim 310 webcam to the supported list of the PAC7302 driver.
For more information see http://linuxtv.org/wiki/index.php/PixArt_PAC7301/PAC7302 .
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Extra spaces to align some variable names and a defined value
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Change of rounded image resolutions to the real ones for MI2020 sensor
in order to discard 2 random lines in the bottom of images
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Setting changes applied after an end of image marker reception
This is the way MI2020 sensor works.
It seems to be logical to wait for a complete image before
to change a setting.
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- 1 ms "msleep" applied to each sensor after USB control data exchange
This was done for two sensors because these exchanges were known to
be too quick depending on laptop model.
It is fairly logical to apply this delay to each sensor
in order to prevent from having errors with untested hardwares.
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- new MI2020 driver version made from a webcam gift
- all previous flavors of this driver removed
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is used when the USB video interface is checked by
the subdriver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- variable / function rename
- set the gains in one exchange
- don't alter the register 80 which contains the AWB flag
and other sensor specific values
- the global gain is now the average of the R, G and B gains.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also renames the last polling message from the closer one
of the ms-windows driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new table is sorted and extracted from a clear part of the MS-Windows
driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also changes a bit the contrast control.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These registers seem to act on the JPEG compression whose control
is not implemented in the current driver.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG header is now included in the subdriver structure instead
of being allocated and freed at capture start and stop.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
setcolors(0 is a no-op for 7670 sensors, so we should not report a
saturation control for 7670 sensors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
What we've called brightness so far actually is an exposure control,
rename it and fixup the maximum and default values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a problem with certain tv8532 cams, where sometimes there
hsync/vsync locks one pixel of where it normally locks. While trying to
fix this (which I failed to do). I noticed there are lots if duplicate
register writes and unnecessary register reads in the tv8532 driver. This
patch cleanes these ups (which has no negative effects, but unfortunately
also does not help).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the ovfx2 bridge sometimes the first few frames in a stream
would be no good, as the bridge and sensor are not in complete hsync /
vsync yet. This can easily be detected by checking the framesize. So if the
framesize is short and it is one of the 1ste 3 frames after an sd_start,
drop it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverse HAS_BUTTON logic since most webcams either have a button or if
they don't don't bother to send any interrupts. However I have at least
one model that appears to leave the button GPIO floating and can send
a bogus interrupt.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Brightness is done by the gamma tables and not by single bridge registers.
It will be back as soon as an algorithm will be found.
This change also fixes the autogain problem found by Jose Alberto Reguero
(webcam 046d:08dd).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error was introduced by "gspca - zc3xx: Rename the USB sequences."
in commit e945e2e44c798f84494260c02478d3c23965bb93.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The webcams 0c45:613e may contain the sensors ov7630 or soi768.
A sensor probe is done at init time when the sensor is declared ov7630.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Handle case of GSPCA=m, INPUT=m when building gspca core;
also handle case of INPUT=n by using stubs.
drivers/media/video/gspca/gspca.c:662: error: implicit declaration of function 'gspca_input_destroy_urb'
drivers/media/video/gspca/gspca.c:668: error: implicit declaration of function 'gspca_input_create_urb'
drivers/media/video/gspca/gspca.c:2284: error: implicit declaration of function 'gspca_input_connect'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that I merged a wrong version of the patch or that
changeset 4d770eeb926d0bc44c0bd68d051d3d2a5568ef41 got mangled somehow:
It were missed the #else to avoid compilation troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_spca561: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix LED control on rev12a cameras and remove the unneeded
sd_stop0 callback function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed buggy init sequence for the OV9655 sensor.
Tested with a 0c45:6288 and 0c45:62b3.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for detecting webcams that are mounted
upside down in laptops. Currently the only two known
are two MSI modesl using the 0c45:624f.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop custom code for handling the input button in
favor of using gspca's input hanlding mechinism.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that setting this options to 50Hz can reduce the framerate, so it is
still disabled (60Hz) by default.
Signed-off-by: Mosalam Ebrahimi <m.ebrahimi@ieee.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Indent with tabs, not with spaces, nor with mixed style.
* Less indentation for controls index comments.
* Use lowercase hex digits.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also set default values unconditionally, for readability.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Adjust comments for sharpness control
* Set default value unconditionally, for readability
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set only the needed bits for AWB, and enable it by default.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Document that even if the state is a u8 value, both MSB and LSB are set
as sd->exposure represents half of the value we are going to set into
registers.
Skip setting exposure when AEC is enabled.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This also makes manual exposure actually work: it never worked before
because AEC was always enabled.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Use 'agc' instead of 'autogain' in the code so to align the naming
as in AEC/AWB.
* Tweak brightness and contrast default values.
* Fix setting/resetting registers values for AGC.
* Set actual gain back when disabling AGC.
* Skip setting GAIN register when AGC is enabled.
* Enable AGC by default.
Note that as Auto Gain Control is now enabled by default, if you are
using the driver for visual computing applications you might need to
disable it explicitly in your software.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hue control doesn't work and the sensor datasheet is not clear about how
to set hue properly.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove Blue/Red Channel Target Value, they are meant for Black Level
Calibration but it is not completely clear how to use them.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the local functions static. Note that the function command_setlights() is
currently not called from anywhere.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'command_setformat' was not declared. Should it be static?
* symbol 'command_setcolourparams' was not declared. Should it be static?
* symbol 'command_setapcor' was not declared. Should it be static?
* symbol 'command_setvloffset' was not declared. Should it be static?
* symbol 'command_setexposure' was not declared. Should it be static?
* symbol 'command_setcolourbalance' was not declared. Should it be static?
* symbol 'command_setcompressiontarget' was not declared. Should it be static?
* symbol 'command_setyuvtresh' was not declared. Should it be static?
* symbol 'command_setcompressionparams' was not declared. Should it be static?
* symbol 'command_setcompression' was not declared. Should it be static?
* symbol 'command_setsensorfps' was not declared. Should it be static?
* symbol 'command_setflickerctrl' was not declared. Should it be static?
* symbol 'command_setecptiming' was not declared. Should it be static?
* symbol 'command_pause' was not declared. Should it be static?
* symbol 'command_resume' was not declared. Should it be static?
* symbol 'command_setlights' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the range of exposure values (0-0x1770) distribute evenly through
HV7131R's exposure control bytes.
Signed-off-by: German Galkin <galkinga@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 0461:0815 camera is spca561 based not spca508
Signed-off-by: John Ellson <john.ellson@comcast.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 046d:08da usb id shouldn't be associated with the stv06xx driver as they're
not compatible with each other.
This fixes a bug where Quickcam Messenger cams fail to use its proper driver
(gspca-zc3xx), rendering the camera inoperable.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use DECLARE_WAIT_QUEUE_HEAD_ONSTACK to make lockdep happy
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
CC: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Only tested with an stv6422 based cam, as that is the only stv06xx cam
I have with a button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitations this only works while the camera is
streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitations this only works while the camera is
streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note due to hardware limitiations (no interrupt endpoint), this only works
when the camera is streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_main: Fix a compile error when CONFIG_INPUT is not set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2 small changes to input device error handling:
1) Make it fatal when we fail to create an input device (it is either this
or add checks for gspca_dev->input_dev being NULL in a lot of places)
2) Since we allow gspca_input_create_urb() to fail everywhere we call it,
and thus never check its return value, make it void.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow use of the gspca core input device creation code by subdrivers which
have non interrupt driven camera buttons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My experience with fixing up the controls for the PAS sensors in
sonixb, has lead me to re-investigate the exposure control for the
pac7302. I've now found a regular exposure register in register bank 3
(which seems to be the sensor registers bank), and with this added a proper
fine grained exposure control. This patch also updates the do_autogain
function to work properly with this new finer grained control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the sonixb driver handle pas106 and pas202 cameras, when both it
and the sn9c102 driver are enabled in the kernel configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup brightness ctrl and add gain and exposure ctrls for PAS106B sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This camera has a sensor type we did not support sofar, this patch adds
support for the new sensor type found in the Sakar 1638x CyberPix.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In 640x480, if the reg11 has less than 4, the image is
unstable (the bridge goes into a higher compression mode
which we have not reverse engineered yet).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup brightness ctrl and add gain and exposure ctrls for PAS202BCB sensors,
this allows enabling autogain (done), and makes the cam usable in low light
conditions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some sensors only allow controlling the exposure by changing the clockdiv,
which means that exposure takes pretty large jumps (for example when going
from a div of 1 to 2, the exposure doubles). Use 2 different entries in
the controls array for these 2 different types of exposure (always
disabling one), and;
Add a new autogain algorithm for the coarse exposure case, which normally
changes the gain setting, only touching the exposure setting if the desired
luminance cannot be reached with gain, and after an exposure change once more
first tries gain, etc. Thus avoiding exposure changes, and the resulting
oscilation because of the huge steps these exposure controls take.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Leave bridge gain at 1.0 when we have a sensor gain, while at it also
change the bridge gain setting code to write both registers in one go
saving us a usb transaction.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixb: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_zc3xx: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_pac7311: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_pac207: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplify sensor detection a bit (share more of the code between cif and vga
cameras). Also remove an unnecessary write from zero_the_pointer().
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression, introduced in the driver split, which made
the ov534 driver unusable.
Plus, the debug message should reflect that we discard also packets
beyond the expected frame size.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
