Hello All,
Quite a while back Michael Ellerman had posted a patch to add support to xmon to print the contents of the console log pointed to by __log_buf.
Here's the link to that patch - http://ozlabs.org/pipermail/linuxppc64-dev/2005-March/003657.html
I've ported the patch in the above link to 2.6.30-rc5 and have tested it.
Thanks & regards,
Vinay
Signed-off-by: Michael Ellerman <michael at ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the 32-bit code uses sg->length instead of sg->dma_lentgh
to report sg_dma_len. However, since the default dma code for 32-bit
(the dma_direct case) sets dma_length and length to the same thing,
we should be able to use dma_length there as well. This gets rid of
some 32-vs-64-bit ifdefs, and is needed by the swiotlb code which
actually distinguishes between dma_length and length.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes an unnecessary double check if the dentry returned by
lookup_create() is actually non-negative. Since lookup_create() itself returns
an error in this case just remove the check.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I have been looking at sources of OS jitter and notice that after a long
NO_HZ idle period we wakeup too early:
relative time (us) event
timer irq exit
999946.405 timer irq entry
4.835 timer irq exit
21.685 timer irq entry
3.540 timer (tick_sched_timer) entry
Here we slept for just under a second then took a timer interrupt that did
nothing. 21.685 us later we wake up again and do the work.
We set a rather low shift value of 16 for the decrementer clockevent, which I
think is causing this issue. On this box we have a 207MHz decrementer and see:
clockevent: decrementer mult[3501] shift[16] cpu[0]
For calculations of large intervals this mult/shift combination could be
off by a significant amount. I notice the sparc code has a loop that iterates
to find a mult/shift combination that maximises the shift value while
keeping mult under 32bit. With the patch below we get:
clockevent: decrementer mult[35015c20] shift[32] cpu[15]
And we no longer see the spurious wakeups.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pcnet32 driver has had in its device id table for some time a match
against the "broken" vendor ID. No need to fake out the vendor ID
with an explicit fixup.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* Removed building setup-irq on ppc32, we don't use it anymore
* Remove duplicate prototype for setup_grackle() code that needs it
gets it from <asm/grackle.h>
* Removed gratuitous pci_io_size type differences between ppc32/ppc64
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There doesn't appear to be any specific reason that we need to setup the
pseries specific notifier in generic arch pci code. Move it into pseries
land.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the device node to just
go get the pci_controller. We can call pci_bus_to_host() for this
purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the device node but call
pci_bus_to_OF_node() for this purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the device node but call
pci_bus_to_OF_node() for this purpose.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We shouldn't directly access sysdata to get the pci_controller. Instead
use pci_bus_to_host() for this purpose. In the future we might have
sysdata be a device_node to match ppc64 and unify the code between ppc32
& ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the PowerPC 2.06 tlbie mnemonics and keeps backwards
compatibilty for CPUs before 2.06.
Only useful for bare metal systems.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Enable MMU feature sections for inline asm
This adds the ability to do MMU feature sections for inline asm.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cleans up the VSX load/store instructions by moving them into
ppc-opcode.h.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make macros more braces happy.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We believe if a toolchain supports PT_GNU_STACK that it sets the proper
PHDR permissions. Therefor elf_read_implies_exec() should only be true
if we don't see PT_GNU_STACK set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So select GENERIC_HARDIRQS_NO__DO_IRQ to disable it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Don't call __do_IRQ() directly in gatwick_action(), use
generic_handle_irq().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should no longer have any irq code that needs __do_IRQ(), so
remove the fallback to __do_IRQ().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The guts of do_IRQ() isn't really the right place to be documenting
the ppc_md.get_irq() interface. So move the comment into machdep.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Makes do_IRQ() shorter and clearer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rather than a giant ifdef in the body of do_IRQ(), including a
dangling else, move the irq stack logic into a separate routine and
do the ifdef there.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ps3 has 4 ipis per cpu and can use the new smp_request_message_ipi to
reduce path length when receiving an ipi.
This has the side effect of setting IRQF_PERCPU.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adds support for the "unused" page hint which can be used in shared
memory partitions to flag pages not in use, which will then be stolen
before active pages by the hypervisor when memory needs to be moved to
LPARs in need of additional memory. Failure to mark pages as 'unused'
makes the LPAR slower to give up unused memory to other partitions.
This adds the kernel parameter 'cmo_free_hint' to disable this
functionality.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
mpic_find() was overloaded to do two things, finding the mpic instance
for a given interrupt and returning if it's an IPI. Instead we introduce
mpic_is_ipi() and simplify mpic_find() to just return the mpic instance
Also silences the warning:
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_set_priority':
arch/powerpc/sysdev/mpic.c:1382: warning: 'is_ipi' may be used uninitialized in this function
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that leds-gpio is a proper OF platform driver, the Warp can use
the leds-gpio driver rather than the old out-of-kernel driver.
One side-effect is the leds-gpio driver always turns the leds off
while the old driver left them alone. So we have to set them back to
the correct settings.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previouslly we just always set the inbound window to 2G. This was
broken for systems with >2G. If a system has >=4G we will need
SWIOTLB support to handle that case.
We now allocate PCICSRBAR/PEXCSRBAR right below the lowest PCI outbound
address for MMIO or the 4G boundary (if the lowest PCI address is above
4G).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2020 is a dual e500v2 core based SOC with:
* 3 PCIe controllers
* 2 General purpose DMA controllers
* 2 sRIO controllers
* 3 eTSECS
* USB 2.0
* SDHC
* SPI, I2C, DUART
* enhanced localbus
* and optional Security (P2020E) security w/XOR acceleration
The p2020 DS reference board is pretty similar to the existing MPC85xx
DS boards and has a ULI 1575 connected on one of the PCIe controllers.
Signed-off-by: Ted Peters <Ted.Peters@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We we build with resource_size_t as a 64-bit quantity we get:
arch/powerpc/sysdev/fsl_rio.c: In function 'fsl_rio_setup':
arch/powerpc/sysdev/fsl_rio.c:1029: warning: format '%08x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
arch/powerpc/sysdev/fsl_rio.c:1029: warning: format '%08x' expects type 'unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In these configuration we expect to have large amounts of memory (> 4G)
and thus will bounce via swiotlb some region of PCI address space.
The outbound windows were wasting 512M of address space by leaving a
gap between the top of the outbound window and the 4G boundary. By
moving the top of the outbound window up to the 4G boundary we can
reclaim the vast majority of the 512M (minus space needed for PEXCSRBAR)
and thus reduces the amount of memory we have to bounce.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its feasible based on how the PCI address map is setup that the region
of PCI address space used for MSIs differs for each PHB on the same SoC.
Instead of assuming that the address mappes to CCSRBAR 1:1 we read
PEXCSRBAR (BAR0) for the PHB that the given pci_dev is on.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For serial flash support we need to:
- Add QE Par IO Bank E device tree node, a GPIO from this bank is
used for SPI chip-select line;
- Add serial-flash node;
- Add proper module alias into of/base.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Select HAS_RAPIDIO symbol and add rio nodes for MPC8568E-MDS
and MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Note that eSDHC and DUART0 are mutually exclusive on MPC8569E-MDS
boards. Default option is DUART0, so eSDHC is disabled by default.
U-Boot will fixup device tree if eSDHC should be used instead of
DUART0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes bogus reg = <> property in the localbus node,
and fixes interrupt property (should be "interrupts").
Also add node for NAND support.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl,exec-units-mask should be 0xbfe to include SNOW unit in
MPC8569E's security engine.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds PCI IDs for MPC8569 and MPC8569E processors,
plus adds appropriate quirks for these IDs, and thus makes
PCI-E actually work on MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Between the addition of the ecm/mcm law nodes and the fact that the
get_immrbase() has been using the range property of the SoC to determine
the base address of CCSR space we no longer need the reg property at
the soc node level. It has been ill specified and varied between device
trees to cover either the {e,m}cm-law node, some odd subset of CCSR
space or all of CCSR space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl,qe-num-riscs and fsl,qe-num-snums to all the devices trees which
have qe node.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8569 is similiar to the MPC8568. It doubles the number of
QUICC Engine RISC cores from 2 to 4. Removes eTSECs, TLU and adds
the eSDHC controller.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The latest QE chip may have more Serial Number(SNUM)s of thread to use. We
will get the number of SNUMs from device tree by reading the new property
"fsl,qe-num-snums", and set 28 as the default number of SNUMs so that it is
compatible with the old QE chips' device trees which don't have this new
property. The macro QE_NUM_OF_SNUM is defined as the maximum number in QE
snum table which is 256.
Also we update the snum_init[] array with 18 more new SNUMs which are
confirmed to be useful on new chip.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the RISC allocation to macros instead of enum, add function to read
the number of risc engines from the new property "fsl,qe-num-riscs" under
the qe node in dts. Add new property "fsl,qe-num-riscs" description in
qe.txt
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Keep an unique machine def for the MPC8568 MDS board to handle some
subtle differences between the future MDS board. Also set the bcsrs in
setup_arch() only for mpc8568_mds because other mds has different bcsr
settings.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the need for asm/mpc86xx.h as it was only used in mpc86xx_smp.c
and just moved the defines it cared about into there. Also fixed up
the ioremap to only map the one 4k page we need access to and to iounmap
when we are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also, convert them to resource_size_t (which is unsigned long
on 64-bit, so it's not a change there).
We will be using these on fsl 32b to indicate the start and size
address of memory that the pci controller can actually reach - this
is needed to determine if an address requires bounce buffering. For
now, initialize them to a standard value; in the near future, the
value will be calculated based on how the inbound windows are
programmed.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Ben Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The rstcr register mapping code was written sometime ago before
of_iomap() existed. We can use it and clean up the code a bit
and get rid of one user of get_immrbase() in the process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new dts places most of the devices in physical address space
above 32-bits, which allows us to have more than 4GB of RAM present.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Refactor the check to determine if the quirk is applicable to the boards
into one inline function so we only have to change one place to add more
boards that the quirks might be applicable to.
Also removed a warning related to unused temp variable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The cell-index property isn't used on PCI nodes and is ill defined.
Remove it for now and if someone comes up with a good reason and
consistent definition for it we can add it back
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's still in the git history if anyone wants it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 9e35ad38 ("perf_counter: Rework the perf counter
disable/enable") added code to the powerpc hw_perf_enable (renamed
from hw_perf_restore) to test cpuhw->disabled and return immediately
if it is not set (i.e. if the PMU is already enabled).
Unfortunately the test got added before cpuhw was initialized,
resulting in an oops the first time hw_perf_enable got called.
This fixes it by moving the initialization of cpuhw to before
cpuhw->disabled is tested.
[ Impact: fix oops-causing bug on powerpc ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <18960.56772.869734.304631@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I don't think anything guarantees that the objects in data.page_aligned
are a multiple of PAGE_SIZE, thus the section may end on any boundary.
So the following section, .data.cacheline_aligned needs an explicit
alignment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Refresh and set these options:
CONFIG_SYSFS_DEPRECATED_V2: y -> n
CONFIG_INPUT_JOYSTICK: y -> n
CONFIG_HID_SONY: n -> m
CONFIG_RTC_DRV_PS3: - -> m
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After upgrading my distcc boxes from gcc 4.2.2 to 4.4.0, the function
graph tracer broke. This was discovered on my x86 boxes.
The issue is that gcc used the same register for an output as it did for
an input in an asm statement. I first thought this was a bug in gcc and
reported it. I was notified that gcc was correct and that the output had
to be flagged as an "early clobber".
I noticed that powerpc had the same issue and this patch fixes it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when #DEBUG
is not defined. That's not really desirable in the ftrace code
which we want to be snappy.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3334 672 4 4010 faa arch/powerpc/kernel/ftrace.o
size after:
text data bss dec hex filename
2616 360 4 2980 ba4 arch/powerpc/kernel/ftrace.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "mm: add /proc controls for pdflush threads"
viocd: needs to depend on BLOCK
block: fix the bio_vec array index out-of-bounds test
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix PCI ROM access
powerpc/pseries: Really fix the oprofile CPU type on pseries
serial/nwpserial: Fix wrong register read address and add interrupt acknowledge.
powerpc/cell: Make ptcal more reliable
powerpc: Allow mem=x cmdline to work with 4G+
powerpc/mpic: Fix incorrect allocation of interrupt rev-map
powerpc: Fix oprofile sampling of marked events on POWER7
powerpc/iseries: Fix pci breakage due to bad dma_data initialization
powerpc: Fix mktree build error on Mac OS X host
powerpc/virtex: Fix duplicate level irq events.
powerpc/virtex: Add uImage to the default images list
powerpc/boot: add simpleImage.* to clean-files list
powerpc/8xx: Update defconfigs
powerpc/embedded6xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/fsl_soc: Remove mpc83xx_wdt_init, again
This uses values from the MMCRA, SIAR and SDAR registers on
powerpc to supply more precise information for overflow events,
including a data address when PERF_RECORD_ADDR is specified.
Since POWER6 uses different bit positions in MMCRA from earlier
processors, this converts the struct power_pmu limited_pmc5_6
field, which only had 0/1 values, into a flags field and
defines bit values for its previous use (PPMU_LIMITED_PMC5_6)
and a new flag (PPMU_ALT_SIPR) to indicate that the processor
uses the POWER6 bit positions rather than the earlier
positions. It also adds definitions in reg.h for the new and
old positions of the bit that indicates that the SIAR and SDAR
values come from the same instruction.
For the data address, the SDAR value is supplied if we are not
doing instruction sampling. In that case there is no guarantee
that the address given in the PERF_RECORD_ADDR subrecord will
correspond to the instruction whose address is given in the
PERF_RECORD_IP subrecord.
If instruction sampling is enabled (e.g. because this counter
is counting a marked instruction event), then we only supply
the SDAR value for the PERF_RECORD_ADDR subrecord if it
corresponds to the instruction whose address is in the
PERF_RECORD_IP subrecord. Otherwise we supply 0.
[ Impact: support more PMU hardware features on PowerPC ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <18955.37028.48861.555309@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Although the perf_counter API allows 63-bit raw event codes,
internally in the powerpc back-end we had been using 32-bit
event codes. This expands them to 64 bits so that we can add
bits for specifying threshold start/stop events and instruction
sampling modes later.
This also corrects the return value of can_go_on_limited_pmc;
we were returning an event code rather than just a 0/1 value in
some circumstances. That didn't particularly matter while event
codes were 32-bit, but now that event codes are 64-bit it
might, so this fixes it.
[ Impact: extend PowerPC perfcounter interfaces from u32 to u64 ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <18955.36874.472452.353104@drongo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Instead of specifying the irq_period for a counter, provide a target interrupt
frequency and dynamically adapt the irq_period to match this frequency.
[ Impact: new perf-counter attribute/feature ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <20090515132018.646195868@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current disable/enable mechanism is:
token = hw_perf_save_disable();
...
/* do bits */
...
hw_perf_restore(token);
This works well, provided that the use nests properly. Except we don't.
x86 NMI/INT throttling has non-nested use of this, breaking things. Therefore
provide a reference counter disable/enable interface, where the first disable
disables the hardware, and the last enable enables the hardware again.
[ Impact: refactor, simplify the PMU disable/enable logic ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A couple of issues crept in since about 2.6.27 related to accessing PCI
device ROMs on various powerpc machines.
First, historically, we don't allocate the ROM resource in the resource
tree. I'm not entirely certain of why, I susepct they often contained
garbage on x86 but it's hard to tell. This causes the current generic
code to always call pci_assign_resource() when trying to access the said
ROM from sysfs, which will try to re-assign some new address regardless
of what the ROM BAR was already set to at boot time. This can be a
problem on hypervisor platforms like pSeries where we aren't supposed
to move PCI devices around (and in fact probably can't).
Second, our code that generates the PCI tree from the OF device-tree
(instead of doing config space probing) which we mostly use on pseries
at the moment, didn't set the (new) flag IORESOURCE_SIZEALIGN on any
resource. That means that any attempt at re-assigning such a resource
with pci_assign_resource() would fail due to resource_alignment()
returning 0.
This fixes this by doing these two things:
- The code that calculates resource flags based on the OF device-node
is improved to set IORESOURCE_SIZEALIGN on any valid BAR, and while at
it also set IORESOURCE_READONLY for ROMs since we were lacking that too
- We now allocate ROM resources as part of the resource tree. However
to limit the chances of nasty conflicts due to busted firmwares, we
only do it on the second pass of our two-passes allocation scheme,
so that all valid and enabled BARs get precedence.
This brings pSeries back the ability to access PCI ROMs via sysfs (and
thus initialize various video cards from X etc...).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
My previous pach for fixing the oprofile CPU type got somewhat mismerged
(by my fault) when it collided with another related patch. This should
finally (fingers crossed) fix the whole thing.
We make sure we keep the -old- oprofile type and CPU type whenever
one of them was specified in the first pass through the function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There have been a series of checkstops on QS21 related to
ptcal being set up incorrectly. On systems that only
have memory on a single node, ptcal fails when it gets
a pointer to memory on the remote node.
Moreover, agressive prefetching in memcpy and other
functions may accidentally touch the first cache line
of the page that we reserve for ptcal, which causes
an ECC checkstop.
We now allocate pages only from the specified node, moves the
ptcal area into the middle of the allocated page to avoid
potential prefetch problems and prints the address of the
ptcal area to facilitate diagnostics.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We're currently choking on mem=4g (and above) due to memory_limit
being specified as an unsigned long. Make memory_limit
phys_addr_t to fix this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Before when we were setting up the irq host map for mpic we passed in
just isu_size for the size of the linear map. However, for a number of
mpic implementations we have no isu (thus pass in 0) and will end up
with a no linear map (size = 0). This causes us to always call
irq_find_mapping() from mpic_get_irq().
By moving the allocation of the host map to after we've determined the
number of sources we can actually benefit from having a linear map for
the non-isu users that covers all the interrupt sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Description
-----------
Change ppc64 oprofile kernel driver to use the SLOT bits (MMCRA[37:39]only on
older processors where those bits are defined.
Background
----------
The performance monitor unit of the 64-bit POWER processor family has the
ability to collect accurate instruction-level samples when profiling on marked
events (i.e., "PM_MRK_<event-name>"). In processors prior to POWER6, the MMCRA
register contained "slot information" that the oprofile kernel driver used to
adjust the value latched in the SIAR at the time of a PMU interrupt. But as of
POWER6, these slot bits in MMCRA are no longer necessary for oprofile to use,
since the SIAR itself holds the accurate sampled instruction address. With
POWER6, these MMCRA slot bits were zero'ed out by hardware so oprofile's use of
these slot bits was, in effect, a NOP. But with POWER7, these bits are no
longer zero'ed out; however, they serve some other purpose rather than slot
information. Thus, using these bits on POWER7 to adjust the SIAR value results
in samples being attributed to the wrong instructions. The attached patch
changes the oprofile kernel driver to ignore these slot bits on all newer
processors starting with POWER6.
Signed-off-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Michael Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4fc665b88a "powerpc: Merge 32 and
64-bit dma code" made changes to the PCI initialisation code that added
an assignment to archdata.dma_data but only for 32 bit code. Commit
7eef440a54 "powerpc/pci: Cosmetic cleanups
of pci-common.c" removed the conditional compilation. Unfortunately,
the iSeries code setup the archdata.dma_data before that assignment was
done - effectively overwriting the dma_data with NULL.
Fix this up by moving the iSeries setup of dma_data into a
pci_dma_dev_setup callback.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mktree utility defines some variables as "uint", although this is not a
standard C type, and so cross-compiling on Mac OS X fails. Change this to
"unsigned int".
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The interrupt controller was not handling level interrupts correctly
such that duplicate interrupts were happening. This fixes the problem
and adds edge type interrupts which are needed in Xilinx hardware.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It is common to use U-Boot on Xilinx Virtex platforms. This patch
ensures that CONFIG_DEFAULT_UIMAGE is selected for virtex
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix this build error when CONFIG_BLOCK is not set:
drivers/cdrom/viocd.c: In function 'viocd_blk_open':
drivers/cdrom/viocd.c:156: error: dereferencing pointer to incomplete type
drivers/cdrom/viocd.c: In function 'viocd_blk_release':
drivers/cdrom/viocd.c:162: error: dereferencing pointer to incomplete type
drivers/cdrom/viocd.c: In function 'viocd_blk_ioctl':
drivers/cdrom/viocd.c:170: error: dereferencing pointer to incomplete type
drivers/cdrom/viocd.c: In function 'viocd_blk_media_changed':
drivers/cdrom/viocd.c:176: error: dereferencing pointer to incomplete type
...
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Merge reason: both topics modify the APIC code but were able to do it in
parallel so far. An upcoming patch generates a conflict so
merge them to avoid the conflict.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver"), possibly due merge issues,
reintroduced completely unneded mpc83xx_wdt_init call, which
I removed some time ago in commit 20d38e01d4
("powerpc/fsl_soc: remove mpc83xx_wdt code").
Remove it once again.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This build failure:
arch/powerpc/sysdev/mpic.c:810: error: conflicting types for 'mpic_set_affinity'
arch/powerpc/sysdev/mpic.h:39: error: previous declaration of 'mpic_set_affinity' was here
make[2]: *** [arch/powerpc/sysdev/mpic.o] Error 1
make[2]: *** Waiting for unfinished jobs....
Triggers because the function prototype was not updated when the
function call signature got changed by:
d5dedd4: irq: change ->set_affinity() to return status
[ Impact: build fix on powerpc ]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix setting of oprofile cpu type
powerpc: Update MPC5xxx and Xilinx Virtex maintainer entries
powerpc adjust oprofile_cpu_type version 3
The powerpc kernel always requires an Open Firmware like device tree
to supply device information. On systems without OF, this comes from
a flattened device tree blob. This blob is usually generated by dtc,
a tool which compiles a text description of the device tree into the
flattened format used by the kernel. Sometimes, the bootwrapper makes
small changes to the pre-compiled device tree blob (e.g. filling in
the size of RAM). To do this it uses the libfdt library.
Because these are only used on powerpc, the code for both these tools
is included under arch/powerpc/boot (these were imported and are
periodically updated from the upstream dtc tree).
However, the microblaze architecture, currently being prepared for
merging to mainline also uses dtc to produce device tree blobs. A few
other archs have also mentioned some interest in using dtc.
Therefore, this patch moves dtc and libfdt from arch/powerpc into
scripts, where it can be used by any architecture.
The vast bulk of this patch is a literal move, the rest is adjusting
the various Makefiles to use dtc and libfdt correctly from their new
locations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers using of_register_platform_driver() wrapper break on sparc
because the wrapper isn't in the header file. This patch moves it from
Microblaze and PowerPC implementations and makes it common code.
Fixes this sparc64 allmodconfig build error (at least):
drivers/leds/leds-gpio.c: In function `gpio_led_init':
drivers/leds/leds-gpio.c:295: error: implicit declaration of function `of_register_platform_driver'
drivers/leds/leds-gpio.c: In function `gpio_led_exit':
drivers/leds/leds-gpio.c:311: error: implicit declaration of function `of_unregister_platform_driver'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 2657dd4e30 introduced a
bug where we would now always override the "real" oprofile CPU
type with the "compatible" one provided by a pseudo-PVR in the
device-tree which is incorrect and breaks oprofile on all current
configs since the "compatible" ones aren't yet recognized.
This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Oprofile is changing the naming it is using for the compatibility modes.
Instead of having compat-power<x>, oprofile will go to family naming
convention and use ibm-compat-v<x>. Currently only ibm-compat-v1 will
be defined.
The notion of compatibility events just started with POWER6. So there is
no way that any other tool could exist that is using these
oprofile_cpu_type strings we want to change.
Signed-off-by: Mike Wolf <mjw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER5+ and POWER6 have two hardware counters with limited functionality:
PMC5 counts instructions completed in run state and PMC6 counts cycles
in run state. (Run state is the state when a hardware RUN bit is 1;
the idle task clears RUN while waiting for work to do and sets it when
there is work to do.)
These counters can't be written to by the kernel, can't generate
interrupts, and don't obey the freeze conditions. That means we can
only use them for per-task counters (where we know we'll always be in
run state; we can't put a per-task counter on an idle task), and only
if we don't want interrupts and we do want to count in all processor
modes.
Obviously some counters can't go on a limited hardware counter, but there
are also situations where we can only put a counter on a limited hardware
counter - if there are already counters on that exclude some processor
modes and we want to put on a per-task cycle or instruction counter that
doesn't exclude any processor mode, it could go on if it can use a
limited hardware counter.
To keep track of these constraints, this adds a flags argument to the
processor-specific get_alternatives() functions, with three bits defined:
one to say that we can accept alternative event codes that go on limited
counters, one to say we only want alternatives on limited counters, and
one to say that this is a per-task counter and therefore events that are
gated by run state are equivalent to those that aren't (e.g. a "cycles"
event is equivalent to a "cycles in run state" event). These flags
are computed for each counter and stored in the counter->hw.counter_base
field (slightly wonky name for what it does, but it was an existing
unused field).
Since the limited counters don't freeze when we freeze the other counters,
we need some special handling to avoid getting skew between things counted
on the limited counters and those counted on normal counters. To minimize
this skew, if we are using any limited counters, we read PMC5 and PMC6
immediately after setting and clearing the freeze bit. This is done in
a single asm in the new write_mmcr0() function.
The code here is specific to PMC5 and PMC6 being the limited hardware
counters. Being more general (e.g. having a bitmap of limited hardware
counter numbers) would have meant more complex code to read the limited
counters when freezing and unfreezing the normal counters, with
conditional branches, which would have increased the skew. Since it
isn't necessary for the code to be more general at this stage, it isn't.
This also extends the back-ends for POWER5+ and POWER6 to be able to
handle up to 6 counters rather than the 4 they previously handled.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <18936.19035.163066.892208@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch renames struct hw_perf_counter_ops into struct pmu. It
introduces a structure to describe a cpu specific pmu (performance
monitoring unit). It may contain ops and data. The new name of the
structure fits better, is shorter, and thus better to handle. Where it
was appropriate, names of function and variable have been changed too.
[ Impact: cleanup ]
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1241002046-8832-7-git-send-email-robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/ps3: Fix build error on UP
powerpc/cell: Select PCI for IBM_CELL_BLADE AND CELLEB
powerpc: ppc32 needs elf_read_implies_exec()
powerpc/86xx: Add device_type entry to soc for ppc9a
powerpc/44x: Correct memory size calculation for denali-based boards
maintainers: Fix PowerPC 4xx git tree
powerpc: fix for long standing bug noticed by gcc 4.4.0
Revert "powerpc: Add support for early tlbilx opcode"
Commit edada399 broke the build on 64-bit powerpc because it moved the
__ftr_alt_* sections of a file away from the .text section, causing
link failures due to relative conditional branch targets being too far
away from the branch instructions. This happens on pretty much all
64-bit powerpc configs.
This change reverts commit edada399 while preserving the update from
the *.refok sections to .ref.text that has happened since.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Requested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A non-SMP version of smp_send_stop() is now included in smp.h.
Remove the unneeded definition in the PS3 smp.c.
Fixes build errors like these when CONFIG_SMP=n:
arch/powerpc/platforms/ps3/setup.c:49: error: redefinition of 'smp_send_stop'
include/linux/smp.h:125: error: previous definition of 'smp_send_stop' was here
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently PPC_CELL_NATIVE selects PPC_OF_PLATFORM_PCI, but does not
select PCI. This can lead to a config with the former and the latter
disabled, which does not build.
To fix this PPC_CELL_NATIVE should select PCI. However, that would
force PCI on for QPACE, which also selects PPC_CELL_NATIVE. So
instead move the select of PPC_OF_PLATFORM_PCI and PCI under both
IBM_CELL_BLADE and CELLEB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64 we implemented elf_read_implies_exec() for 32-bit binaries
because old toolchains had bugs where they didn't mark program
segments executable that needed to be. For some reason we didn't do
this on ppc32 builds. This hadn't been an issue until commit 8d30c14c
("powerpc/mm: Rework I$/D$ coherency (v3)"), which had as a side
effect that we are now enforcing execute permissions to some extent on
32-bit 4xx and Book E processors.
This fixes it by defining elf_read_implies_exec on 32-bit to turn on
the read-implies-exec behaviour on programs that are sufficiently old
that they don't have a PT_GNU_STACK program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The section .text.init.refok is deprecated and __REF (.ref.text)
should be used in assembly files instead. This patch cleans up a few
uses of .text.init.refok in the powerpc architecture.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than adding .ref.text to the powerpc linker script so that we
can use __REF on the powerpc architecture, it seems simpler to switch
to using the generic TEXT_TEXT macro.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'device_type = "soc";' line *is* needed in the DTS for get_immrbase()
to return the correct address.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch modifies the bitbanged MDIO driver in the ep8248e platform
code to use the common of_mdio infrastructure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the driver by making use of more common code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text". Since this commit changes all
users in the architecture, this change should be harmless.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix modular build of ide-pmac when mediabay is built in
powerpc/pasemi: Fix build error on UP
powerpc: Make macintosh/mediabay driver depend on CONFIG_BLOCK
maintainers: Fix PS3 patterns
powerpc/ps3: Fix CONFIG_PS3_FLASH=n build warning
powerpc/32: Don't clobber personality flags on exec
powerpc: Fix crash on CPU hotplug
powerpc/85xx: Remove defconfigs that mpc85xx_{smp_}defconfig cover
powerpc/85xx: Added SMP defconfig
powerpc/85xx: Enabled a bunch of FSL specific drivers/options
powerpc/85xx: Updated generic mpc85xx_defconfig
powerpc: don't disable SATA interrupts on Freescale MPC8610 HPCD
fsl_rio: Pass the proper device to dma mapping routines
powerpc: Fix of_node_put() exit path in of_irq_map_one()
powerpc/5200: defconfig updates
powerpc/5200: Add FLASH nodes to lite5200 device tree
powerpc/device-tree: Document MTD nodes with multiple "reg" tuples
powerpc/of-device-tree: Factor MTD physmap bindings out of booting-without-of
powerpc/5200: Bring the legacy fsl_spi_platform_data hooks back
Some U-Boot versions incorrectly set the number of chipselects to two
for Sequoia/Rainier boards while they only have one chipselect hardwired.
This patch adds a workaround for this, hardcoding the number of chipselects
to one for sequioa/rainer board models and reading the actual value from
the memory controller register DDR0_10 otherwise.
It also fixes another error in the way ibm4xx_denali_fixup_memsize
calculates memory size. When testing the DDR_REDUC bit, the polarity is
backwards. A "1" implies 32-bit wide memory while a "0" implies 64-bit
wide memory.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Previous gcc versions didn't notice this because one of the preceding
#ifs always evaluated to true.
gcc 4.4.0 produced this error:
arch/powerpc/mm/tlb_nohash_low.S:206:6: error: #elif with no expression
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit e996557740. Our HW
guys were able to fix this so it never sees the light of day.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A non-SMP version of smp_send_stop() is now included in smp.h.
Remove the unneeded definition in the pasemi setup.c.
Fixes build errors like these when CONFIG_SMP=n:
arch/powerpc/platforms/pasemi/setup.c:48: error: redefinition of ‘smp_send_stop’
include/linux/smp.h:125: error: previous definition of 'smp_send_stop' was here
Reported-by: subrata@linux.vnet.ibm.com
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix build warnings like these when CONFIG_PS3_FLASH=n:
arch/powerpc/platforms/ps3/os-area.c: warning: 'update_flash_db' defined but not used
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that ppc32 implements address randomization it also wants to inherit
personality flags like ADDR_NO_RANDOMIZE across exec, for things like
`setarch ppc -R' to work. But the ppc32 version of SET_PERSONALITY
forcefully sets PER_LINUX, clearing all personality flags. So be
careful about preserving the flags.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
early_init_mmu_secondary() is called at CPU hotplug time, so it
must be marked as __cpuinit, not __init.
Caused by 757c74d2 ("powerpc/mm: Introduce early_init_mmu() on 64-bit").
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the vast majority of 85xx platforms are UP we introduce a new SMP
config for the few platforms that have more than one core. Beyond
CONFIG_SMP=y and its dependencies this should be identical to
mpc85xx_defconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ULI 1575 PCI quirk function for the Freescale MPC8610 HPCD was disabling
the SATA INTx interrupt, even when SATA support was enabled. This was safe,
because the SATA driver re-enabled it. But with commit a5bfc471 ("ahci: drop
intx manipulation on msi enable"), the driver no longer does this, and so SATA
support on the 8610 HPCD is broken.
The original quirk function disabled INTx because it caused some other
interrupt problem during early development on this board, but no one remembers
any more what that problem was, and it doesn't seem to occur any more.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver should pass a device that specifies internal DMA ops, but
currently NULL pointer is passed, therefore following bug appears
during boot up:
------------[ cut here ]------------
Kernel BUG at c0018a7c [verbose debug info unavailable]
Oops: Exception in kernel mode, sig: 5 [#1]
[...]
NIP [c0018a7c] fsl_rio_doorbell_init+0x34/0x60
LR [c0018a70] fsl_rio_doorbell_init+0x28/0x60
Call Trace:
[ef82bda0] [c0018a70] fsl_rio_doorbell_init+0x28/0x60 (unreliable)
[ef82bdc0] [c0019160] fsl_rio_setup+0x6b8/0x84c
[ef82be20] [c02d28ac] fsl_of_rio_rpn_probe+0x30/0x50
[ef82be40] [c0234f20] of_platform_device_probe+0x5c/0x84
[...]
---[ end trace 561bb236c800851f ]---
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: pseries/dtl.c should include asm/firmware.h
powerpc: Fix data-corrupting bug in __futex_atomic_op
powerpc/pseries: Set error_state to pci_channel_io_normal in eeh_report_reset()
powerpc: Allow 256kB pages with SHMEM
powerpc: Document new FSL I2C bindings and cleanup
powerpc/mm: Fix compile warning
powerpc/85xx: TQM8548: update defconfig
powerpc/85xx: TQM8548: use proper phy-handles for enet2 and enet3
powerpc/85xx: TQM85xx: correct address of LM75 I2C device nodes
powerpc: Add support for early tlbilx opcode
powerpc: Fix tlbilx opcode
A randconfig build on powerpc failed with:
dtl.c: In function 'dtl_init':
dtl.c:238: error: implicit declaration of function 'firmware_has_feature'
dtl.c:238: error: 'FW_FEATURE_SPLPAR' undeclared (first use in this function)
- We need firmware.h for these definitions.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Richard Henderson pointed out that the powerpc __futex_atomic_op has a
bug: it will write the wrong value if the stwcx. fails and it has to
retry the lwarx/stwcx. loop, since 'oparg' will have been overwritten
by the result from the first time around the loop. This happens
because it uses the same register for 'oparg' (an input) as it uses
for the result.
This fixes it by using separate registers for 'oparg' and 'ret'.
Cc: stable@kernel.org
Signed-off-by: Paul Mackerras <paulus@samba.org>
While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.
Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.
The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure. Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.
The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.
Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.
Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.
PAPR defines the following 3 states:
0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
(Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
(Slot Frozen)
An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.
The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that shmem's divisions by zero and SHMEM_MAX_BYTES are fixed,
let powerpc 256kB pages coexist with CONFIG_SHMEM again.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 51dcdfec6a ("parport: Use the
PCI IRQ if offered") parport_pc_probe_port() gained an irqflags arg.
This isn't being supplied on powerpc. This patch make powerpc fallback
to the old behaviour, that is using "0" for irqflags.
Fixes build failure:
In file included from drivers/parport/parport_pc.c:68:
arch/powerpc/include/asm/parport.h: In function 'parport_pc_find_nonpci_ports':
arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
arch/powerpc/include/asm/parport.h:32: error: too few arguments to function 'parport_pc_probe_port'
make[3]: *** [drivers/parport/parport_pc.o] Error 1
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix potential deadlocks on powerpc
Now that the core is using in_nmi() (added in e30e08f6, "perf_counter:
fix NMI race in task clock"), we need the powerpc perf_counter_interrupt
to call nmi_enter() and nmi_exit() in those cases where the interrupt
happens when interrupts are soft-disabled.
If interrupts were soft-enabled, we can treat it as a regular interrupt
and do irq_enter/irq_exit around the whole routine. This lets us get rid
of the test_perf_counter_pending() call at the end of
perf_counter_interrupt, thus simplifying things a little.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18909.31952.873098.336615@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Paul suggested we allow for data addresses to be recorded along with
the traditional IPs as power can provide these.
For now, only the software pagefault events provide data addresses,
but in the future power might as well for some events.
x86 doesn't seem capable of providing this atm.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090408130409.394816925@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: enable access to hardware feature
POWER processors have the ability to "mark" a subset of the instructions
and provide more detailed information on what happens to the marked
instructions as they flow through the pipeline. This marking is
enabled by the "sample enable" bit in MMCRA, and there are
synchronization requirements around setting and clearing the bit.
This adds logic to the processor-specific back-ends so that they know
which events relate to marked instructions and set the sampling enable
bit if any event that we want to put on the PMU is a marked instruction
event. It also adds logic to the generic powerpc code to do the
necessary synchronization if that bit is set.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18908.31930.1024.228867@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 4af4998b ("perf_counter: rework context time") changed struct
perf_counter_context to have a 'time' field instead of a 'time_now'
field, but neglected to fix the place in the powerpc perf_counter.c
where the time_now field was accessed. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <18908.31922.411398.147810@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
arch/powerpc/include/asm/systbl.h
arch/powerpc/include/asm/unistd.h
include/linux/init_task.h
Merge reason: the conflicts are non-trivial: PowerPC placement
of sys_perf_counter_open has to be mixed with the
new preadv/pwrite syscalls.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/powerpc/mm/tlb_nohash.c: In function 'flush_tlb_mm':
arch/powerpc/mm/tlb_nohash.c:128: warning: unused variable 'cpu_mask'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (28 commits)
powerpc: Fix oops when loading modules
powerpc: Wire up preadv and pwritev
powerpc/ftrace: Fix printf format warning
powerpc/ftrace: Fix #if that should be #ifdef
powerpc: Fix ptrace compat wrapper for FPU register access
powerpc: Print information about mapping hw irqs to virtual irqs
powerpc: Correct dependency of KEXEC
powerpc: Disable VSX or current process in giveup_fpu/altivec
powerpc/pseries: Enable relay in pseries_defconfig
powerpc/pseries: Fix ibm,client-architecture comment
powerpc/pseries: Scan for all events in rtasd
powerpc/pseries: Add dispatch dispersion statistics
powerpc: Clean up some prom printouts
powerpc: Print progress of ibm,client-architecture method
powerpc: Remove duplicated #include's
powerpc/pmac: Fix internal modem IRQ on Wallstreet PowerBook
powerpc/wdrtas: Update wdrtas_get_interval to use rtas_data_buf
fsl-diu-fb: Pass the proper device for dma mapping routines
powerpc/pq2fads: Update device tree for use with device-tree-aware u-boot.
cpm_uart: Disable CPM udbg when re-initing CPM uart, even if not the console.
...
Preserve I2C clock settings for the Socrates MPC8544 board.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare for more generic overflow handling. The new perf_counter_overflow()
method will handle the generic bits of the counter overflow, and can return
a !0 return value, in which case the counter should be (soft) disabled, so
that it won't count until it's properly disabled.
XXX: do powerpc and swcounter
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
LKML-Reference: <20090406094517.812109629@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Enable highmem support for the TQM8548-AG modules and NAND support for
the TQM8548-BE modules. Furthermore disable USB, Wireless and IDE support
because it's not available on the STK85xx starter kit.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For enet2 and enet3 the wrong phy-handles have been used in DTS files
of the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 0f73a449a6 added I2C device nodes
for the LM75 thermal sensor on the TQM85xx modules, unfortunately with
the wrong I2C address. The LM75s are located at address 0x48.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
During the ISA 2.06 development the opcode for tlbilx changed and some
early implementations used to old opcode. Add support for a MMU_FTR
fixup to deal with this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The tlbilx opcode was not matching the Power ISA 2.06 arch spec.
The old opcode was an early suggested opcode that changed during the
2.06 architecture process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops. We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.
This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[paulus@samba.org: changed to use syscall numbers 320 and 321 since
perf_counters is currently using 319.]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
'tramp' is an unsigned long, so print it with %lx.
Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit bb7253403f ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64. This changes it to #ifdef.
Fixes the following warning on 32-bit builds:
arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ptrace compat wrapper mishandles access to the fpu registers. The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro. The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset). The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.
So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 28794d34ec ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we call giveup_fpu, we need to need to turn off VSX for the
current process. If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct. Ditto for
altivec.
This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on. Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.
lfs unaligned <- alignment exception turns FP off but leaves VSX on
VSX instruction <- no exception since VSX on, hence we get the
wrong VSX register values for VSX registers 0-31,
which overlap the FPRs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of checking for known events, pass in all 1s so we handle future
event types. We were currently missing the IO event type.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make all messages consistent, some have spaces before the "...", some do not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:
Hypertas detected, assuming LPAR !
Which doesn't explain what just happened. Wrap the ibm,client-architecture
so it's clear what is going on:
Calling ibm,client-architecture... done
In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.infradead.org/mtd-2.6: (53 commits)
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] [NOR] Fixup for Numonyx M29W128 chips
[MTD] mtdpart: Make ecc_stats more realistic.
powerpc/85xx: TQM8548: Update DTS file for multi-chip support
powerpc: NAND: FSL UPM: document new bindings
[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
[MTD] [NAND] FSL-UPM: add multi chip support
[MTD] [NOR] Add device parent info to physmap_of
[MTD] [NAND] Add support for NAND on the Socrates board
[MTD] [NAND] Add support for 4KiB pages.
[MTD] sysfs support should not depend on CONFIG_PROC_FS
[MTD] [NAND] Add parent info for CAFÉ controller
[MTD] support driver model updates
[MTD] driver model updates (part 2)
[MTD] driver model updates
[MTD] [NAND] move gen_nand's probe function to .devinit.text
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
[MTD] fix use after free in register_mtd_blktrans
[MTD] [MAPS] Drop now unused sharpsl-flash map
[MTD] ofpart: Check name property to determine partition nodes.
...
Manually fix trivial conflict in drivers/mtd/maps/Makefile
This patch adds multi-chip support for the Micron MT29F8G08FAB NAND
flash memory on the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add aliases, and correct CS0 offset to match how u-boot
programs it (this was not a problem with cuImage because
the wrapper would reprogram the localbus to match the device
tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CoreInt provides a mechansim to deliver the IRQ vector directly
into the core on an interrupt (via the SPR EPR) rather than having
to go IACK on the PIC. This is suppose to provide an improvment
in interrupt latency by reducing the time to get the IRQ vector.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Impact: better error reporting
At present, if hw_perf_counter_init encounters an error, all it can do
is return NULL, which causes sys_perf_counter_open to return an EINVAL
error to userspace. This isn't very informative for userspace; it means
that userspace can't tell the difference between "sorry, oprofile is
already using the PMU" and "we don't support this CPU" and "this CPU
doesn't support the requested generic hardware event".
This commit uses the PTR_ERR/ERR_PTR/IS_ERR set of macros to let
hw_perf_counter_init return an error code on error rather than just NULL
if it wishes. If it does so, that error code will be returned from
sys_perf_counter_open to userspace. If it returns NULL, an EINVAL
error will be returned to userspace, as before.
This also adapts the powerpc hw_perf_counter_init to make use of this
to return ENXIO, EINVAL, EBUSY, or EOPNOTSUPP as appropriate. It would
be good to add extra error numbers in future to allow userspace to
distinguish the various errors that are currently reported as EINVAL,
i.e. irq_period < 0, too many events in a group, conflict between
exclude_* settings in a group, and PMU resource conflict in a group.
[ v2: fix a bug pointed out by Corey Ashford where error returns from
hw_perf_counter_init were not handled correctly in the case of
raw hardware events.]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Orig-LKML-Reference: <20090330171023.682428180@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cooperate with oprofile
At present, on PowerPC, if you have perf_counters compiled in, oprofile
doesn't work. There is code to allow the PMU to be shared between
competing subsystems, such as perf_counters and oprofile, but currently
the perf_counter subsystem reserves the PMU for itself at boot time,
and never releases it.
This makes perf_counter play nicely with oprofile. Now we keep a count
of how many perf_counter instances are counting hardware events, and
reserve the PMU when that count becomes non-zero, and release the PMU
when that count becomes zero. This means that it is possible to have
perf_counters compiled in and still use oprofile, as long as there are
no hardware perf_counters active. This also means that if oprofile is
active, sys_perf_counter_open will fail if the hw_event specifies a
hardware event.
To avoid races with other tasks creating and destroying perf_counters,
we use a mutex. We use atomic_inc_not_zero and atomic_add_unless to
avoid having to take the mutex unless there is a possibility of the
count going between 0 and 1.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Orig-LKML-Reference: <20090330171023.627912475@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While going over the wakeup code I noticed delayed wakeups only work
for hardware counters but basically all software counters rely on
them.
This patch unifies and generalizes the delayed wakeup to fix this
issue.
Since we're dealing with NMI context bits here, use a cmpxchg() based
single link list implementation to track counters that have pending
wakeups.
[ This should really be generic code for delayed wakeups, but since we
cannot use cmpxchg()/xchg() in generic code, I've let it live in the
perf_counter code. -- Eric Dumazet could use it to aggregate the
network wakeups. ]
Furthermore, the x86 method of using TIF flags was flawed in that its
quite possible to end up setting the bit on the idle task, loosing the
wakeup.
The powerpc method uses per-cpu storage and does appear to be
sufficient.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090330171023.153932974@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: new functionality
Currently, if there are more counters enabled than can fit on the CPU,
the kernel will multiplex the counters on to the hardware using
round-robin scheduling. That isn't too bad for sampling counters, but
for counting counters it means that the value read from a counter
represents some unknown fraction of the true count of events that
occurred while the counter was enabled.
This remedies the situation by keeping track of how long each counter
is enabled for, and how long it is actually on the cpu and counting
events. These times are recorded in nanoseconds using the task clock
for per-task counters and the cpu clock for per-cpu counters.
These values can be supplied to userspace on a read from the counter.
Userspace requests that they be supplied after the counter value by
setting the PERF_FORMAT_TOTAL_TIME_ENABLED and/or
PERF_FORMAT_TOTAL_TIME_RUNNING bits in the hw_event.read_format field
when creating the counter. (There is no way to change the read format
after the counter is created, though it would be possible to add some
way to do that.)
Using this information it is possible for userspace to scale the count
it reads from the counter to get an estimate of the true count:
true_count_estimate = count * total_time_enabled / total_time_running
This also lets userspace detect the situation where the counter never
got to go on the cpu: total_time_running == 0.
This functionality has been requested by the PAPI developers, and will
be generally needed for interpreting the count values from counting
counters correctly.
In the implementation, this keeps 5 time values (in nanoseconds) for
each counter: total_time_enabled and total_time_running are used when
the counter is in state OFF or ERROR and for reporting back to
userspace. When the counter is in state INACTIVE or ACTIVE, it is the
tstamp_enabled, tstamp_running and tstamp_stopped values that are
relevant, and total_time_enabled and total_time_running are determined
from them. (tstamp_stopped is only used in INACTIVE state.) The
reason for doing it like this is that it means that only counters
being enabled or disabled at sched-in and sched-out time need to be
updated. There are no new loops that iterate over all counters to
update total_time_enabled or total_time_running.
This also keeps separate child_total_time_running and
child_total_time_enabled fields that get added in when reporting the
totals to userspace. They are separate fields so that they can be
atomic. We don't want to use atomics for total_time_running,
total_time_enabled etc., because then we would have to use atomic
sequences to update them, which are slower than regular arithmetic and
memory accesses.
It is possible to measure total_time_running by adding a task_clock
counter to each group of counters, and total_time_enabled can be
measured approximately with a top-level task_clock counter (though
inaccuracies will creep in if you need to disable and enable groups
since it is not possible in general to disable/enable the top-level
task_clock counter simultaneously with another group). However, that
adds extra overhead - I measured around 15% increase in the context
switch latency reported by lat_ctx (from lmbench) when a task_clock
counter was added to each of 2 groups, and around 25% increase when a
task_clock counter was added to each of 4 groups. (In both cases a
top-level task-clock counter was also added.)
In contrast, the code added in this commit gives better information
with no overhead that I could measure (in fact in some cases I
measured lower times with this code, but the differences were all less
than one standard deviation).
[ v2: address review comments by Andrew Morton. ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Orig-LKML-Reference: <18890.6578.728637.139402@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Rework the perfcounter output ABI
use sys_read() only for instant data and provide mmap() output for all
async overflow data.
The first mmap() determines the size of the output buffer. The mmap()
size must be a PAGE_SIZE multiple of 1+pages, where pages must be a
power of 2 or 0. Further mmap()s of the same fd must have the same
size. Once all maps are gone, you can again mmap() with a new size.
In case of 0 extra pages there is no data output and the first page
only contains meta data.
When there are data pages, a poll() event will be generated for each
full page of data. Furthermore, the output is circular. This means
that although 1 page is a valid configuration, its useless, since
we'll start overwriting it the instant we report a full page.
Future work will focus on the output format (currently maintained)
where we'll likey want each entry denoted by a header which includes a
type and length.
Further future work will allow to splice() the fd, also containing the
async overflow data -- splice() would be mutually exclusive with
mmap() of the data.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090323172417.470536358@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: new feature giving performance improvement
This adds the ability for userspace to do an mmap on a hardware counter
fd and get access to a read-only page that contains the information
needed to translate a hardware counter value to the full 64-bit
counter value that would be returned by a read on the fd. This is
useful on architectures that allow user programs to read the hardware
counters, such as PowerPC.
The mmap will only succeed if the counter is a hardware counter
monitoring the current process.
On my quad 2.5GHz PowerPC 970MP machine, userspace can read a counter
and translate it to the full 64-bit value in about 30ns using the
mmapped page, compared to about 830ns for the read syscall on the
counter, so this does give a significant performance improvement.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Orig-LKML-Reference: <20090323172417.297057964@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the bitfields turned into a bit of a mess, remove them and rely on
good old masks.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Orig-LKML-Reference: <20090323172417.059499915@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix for powerpc
Commit db3a944aca35ae61 ("perf_counter: revamp syscall input ABI")
expanded the hw_event.type field into a union of structs containing
bitfields. In particular it introduced a type field and a raw_type
field, with the intention that the 1-bit raw_type field should
overlay the most-significant bit of the 8-bit type field, and in fact
perf_counter_alloc() now assumes that (or at least, assumes that
raw_type doesn't overlay any of the bits that are 1 in the values of
PERF_TYPE_{HARDWARE,SOFTWARE,TRACEPOINT}).
Unfortunately this is not true on big-endian systems such as PowerPC,
where bitfields are laid out from left to right, i.e. from most
significant bit to least significant. This means that setting
hw_event.type = PERF_TYPE_SOFTWARE will set hw_event.raw_type to 1.
This fixes it by making the layout depend on whether or not
__BIG_ENDIAN_BITFIELD is defined. It's a bit ugly, but that's what
we get for using bitfields in a user/kernel ABI.
Also, that commit didn't fix up some places in arch/powerpc/kernel/
perf_counter.c where hw_event.raw and hw_event.event_id were used.
This fixes them too.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: cleanup
This updates the powerpc perf_counter_interrupt following on from the
"perf_counter: unify irq output code" patch. Since we now use the
generic perf_counter_output code, which sets the perf_counter_pending
flag directly, we no longer need the need_wakeup variable.
This removes need_wakeup and makes perf_counter_interrupt use
get_perf_counter_pending() instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Orig-LKML-Reference: <20090319194234.024464535@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Having 3 slightly different copies of the same code around does nobody
any good. First step in revamping the output format.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Orig-LKML-Reference: <20090319194233.929962222@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: modify ABI
The hardware/software classification in hw_event->type became a little
strained due to the addition of tracepoint tracing.
Instead split up the field and provide a type field to explicitly specify
the counter type, while using the event_id field to specify which event to
use.
Raw counters still work as before, only the raw config now goes into
raw_event.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Orig-LKML-Reference: <20090319194233.836807573@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build fix for powerpc
Commit bd753921015e7905 ("perf_counter: software counter event
infrastructure") introduced a use of TIF_PERF_COUNTERS into the core
perfcounter code. This breaks the build on powerpc because we use
a flag in a per-cpu area to signal wakeups on powerpc rather than
a thread_info flag, because the thread_info flags have to be
manipulated with atomic operations and are thus slower than per-cpu
flags.
This fixes the by changing the core to use an abstracted
set_perf_counter_pending() function, which is defined on x86 to set
the TIF_PERF_COUNTERS flag and on powerpc to set the per-cpu flag
(paca->perf_counter_pending). It changes the previous powerpc
definition of set_perf_counter_pending to not take an argument and
adds a clear_perf_counter_pending, so as to simplify the definition
on x86.
On x86, set_perf_counter_pending() is defined as a macro. Defining
it as a static inline in arch/x86/include/asm/perf_counters.h causes
compile failures because <asm/perf_counters.h> gets included early in
<linux/sched.h>, and the definitions of set_tsk_thread_flag etc. are
therefore not available in <asm/perf_counters.h>. (On powerpc this
problem is avoided by defining set_perf_counter_pending etc. in
<asm/hw_irq.h>.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide separate sw counters for major and minor page faults.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We use the generic software counter infrastructure to provide
page fault events.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: we have gathered quite a few conflicts, need to merge upstream
Conflicts:
arch/powerpc/kernel/Makefile
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/hardirq.h
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
arch/x86/kernel/cpu/common.c
arch/x86/kernel/irq.c
arch/x86/kernel/syscall_table_32.S
arch/x86/mm/iomap_32.c
include/linux/sched.h
kernel/Makefile
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
Remove two unneeded exports and make two symbols static in fs/mpage.c
Cleanup after commit 585d3bc06f
Trim includes of fdtable.h
Don't crap into descriptor table in binfmt_som
Trim includes in binfmt_elf
Don't mess with descriptor table in load_elf_binary()
Get rid of indirect include of fs_struct.h
New helper - current_umask()
check_unsafe_exec() doesn't care about signal handlers sharing
New locking/refcounting for fs_struct
Take fs_struct handling to new file (fs/fs_struct.c)
Get rid of bumping fs_struct refcount in pivot_root(2)
Kill unsharing fs_struct in __set_personality()
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a build failure with generic debug pagealloc:
mm/debug-pagealloc.c: In function 'set_page_poison':
mm/debug-pagealloc.c:8: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: In function 'clear_page_poison':
mm/debug-pagealloc.c:13: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: In function 'page_poison':
mm/debug-pagealloc.c:18: error: 'struct page' has no member named 'debug_flags'
mm/debug-pagealloc.c: At top level:
mm/debug-pagealloc.c:120: error: redefinition of 'kernel_map_pages'
include/linux/mm.h:1278: error: previous definition of 'kernel_map_pages' was here
mm/debug-pagealloc.c: In function 'kernel_map_pages':
mm/debug-pagealloc.c:122: error: 'debug_pagealloc_enabled' undeclared (first use in this function)
by fixing
- debug_flags should be in struct page
- define DEBUG_PAGEALLOC config option for all architectures
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While normally we don't use the math emulation code on ppc64 it can be
useful for doing things like emulating the embedded FP instructions.
Since performance isn't critical in this scenario its easier to keep
the sizes of the various math-emu the same as on ppc32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The device_type "soc" is still required for MPC85xx boards.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SPEFSCR is a user space register and doesn't conflict with anything.
Moving the defines of the various bit fields makes some emulation
code have fewer ifdefs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PowerPC has been a long time user of the generic RTC abstraction, so hook up
rtc-generic:
- Create the "rtc-generic" platform device if ppc_md.get_rtc_time is set,
- Kill rtc-ppc, as rtc-generic offers the same functionality in a more
generic way, and supports autoloading through udev.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Today's linux-next build (powerpc allyesconfig) failed like this:
arch/powerpc/kernel/ftrace.c: In function 'prepare_ftrace_return':
arch/powerpc/kernel/ftrace.c:612: warning: passing argument 3 of 'ftrace_push_return_trace' makes pointer from integer without a cast
arch/powerpc/kernel/ftrace.c:612: error: too many arguments to function 'ftrace_push_return_trace'
Caused by commit 5d1a03dc54
("function-graph: moved the timestamp from arch to generic code") from
the tracing tree which (removed an argument from
ftrace_push_return_trace()) interacting with commit
6794c78243 ("powerpc64: port of the
function graph tracer") from the powerpc tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <linuxppc-dev@ozlabs.org>
LKML-Reference: <20090327230834.93d0221d.sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
The advantages of this:
- Don't encourage legacy support;
- Less external symbols, less code to compile-in for !MPC832x_RDB
platforms.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add gpio-controller node to manage QE GPIO Bank D;
- Add mmc-spi node;
- Modify board file so that it won't use legacy SPI support with the new
device trees.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main purpose of this patch is to pass 'struct spi_device' to the chip
select handling routines. This is needed so that we could implement
full-fledged OpenFirmware support for this driver.
While at it, also:
- Replace two {de,activate}_cs routines by single cs_contol().
- Don't duplicate platform data callbacks in mpc83xx_spi struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use debug_kmap_atomic in kmap_atomic, kmap_atomic_pfn, and
iomap_atomic_prot_pfn.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_DEBUG_PAGEALLOC is now supported by x86, powerpc, sparc64, and
s390. This patch implements it for the rest of the architectures by
filling the pages with poison byte patterns after free_pages() and
verifying the poison patterns before alloc_pages().
This generic one cannot detect invalid page accesses immediately but
invalid read access may cause invalid dereference by poisoned memory and
invalid write access can be detected after a long delay.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Older devices tree's used "fsl,85.." instead of the preferred
"fsl,mpc85.." for the memory controller & l2 cache controller nodes.
The EDAC code is the only use of these and has been updated for some
time to support both "fsl,85.." and "fsl,mpc85.."
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The recent addition of CONFIG_LOWMEM_CAM_BOOL and
CONFIG_LOWMEM_CAM_NUM cause the latter to show up in configs
that do not need it during 'make oldconfig'. Make LOWMEM_CAM_NUM
depend on FSL_BOOKE.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Everyone defines it, and only one person uses it
(arch/mips/sgi-ip27/ip27-nmi.c). So just open code it there.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-mips@linux-mips.org
Conflicts:
arch/sparc/kernel/time_64.c
drivers/gpu/drm/drm_proc.c
Manual merge to resolve build warning due to phys_addr_t type change
on x86:
drivers/gpu/drm/drm_info.c
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Due to a different size of ino_t ustat needs a compat handler, but
currently only x86 and mips provide one. Add a generic compat_sys_ustat
and switch all architectures over to it. Instead of doing various
user copy hacks compat_sys_ustat just reimplements sys_ustat as
it's trivial. This was suggested by Arnd Bergmann.
Found by Eric Sandeen when running xfstests/017 on ppc64, which causes
stack smashing warnings on RHEL/Fedora due to the too large amount of
data writen by the syscall.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.
The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.
For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:
can@3,100 {
compatible = "philips,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 2>;
interrupts = <2 8 1>; // number, type, routing
interrupt-parent = <&fpga_pic>;
};
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Rakhchev <rda@emcraft.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rusty's patch to change our sysfs access to various registers
to use smp_call_function_single() introduced a whole bunch of
warnings. This fixes them. This version also fixes an actual
bug in here where it did mtspr instead of mfspr when reading
the files
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On powerpc64 machines running 32-bit userspace, we can get garbage bits in the
stack pointer passed into the kernel. Most places handle this correctly, but
the signal handling code uses the passed value directly for allocating signal
stack frames.
This fixes the issue by introducing a get_clean_sp function that returns a
sanitized stack pointer. For 32-bit tasks on a 64-bit kernel, the stack
pointer is masked correctly. In all other cases, the stack pointer is simply
returned.
Additionally, we pass an 'is_32' parameter to get_sigframe now in order to
get the properly sanitized stack. The callers are know to be 32 or 64-bit
statically.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we don't enforce any ordering for updates to the lppaca
when enabling dtl logging, so we may end up enabling logging before the
index fields have been established.
This change adds a smp_wmb() before doing the actual enable.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (113 commits)
KVM: VMX: Don't allow uninhibited access to EFER on i386
KVM: Correct deassign device ioctl to IOW
KVM: ppc: e500: Fix the bug that KVM is unstable in SMP
KVM: ppc: e500: Fix the bug that mas0 update to wrong value when read TLB entry
KVM: Fix missing smp tlb flush in invlpg
KVM: Get support IRQ routing entry counts
KVM: fix sparse warnings: Should it be static?
KVM: fix sparse warnings: context imbalance
KVM: is_long_mode() should check for EFER.LMA
KVM: VMX: Update necessary state when guest enters long mode
KVM: ia64: Fix the build errors due to lack of macros related to MSI.
ia64: Move the macro definitions related to MSI to one header file.
KVM: fix kvm_vm_ioctl_deassign_device
KVM: define KVM_CAP_DEVICE_DEASSIGNMENT
KVM: ppc: Add emulation of E500 register mmucsr0
KVM: Report IRQ injection status for MSI delivered interrupts
KVM: MMU: Fix another largepage memory leak
KVM: SVM: set accessed bit for VMCB segment selectors
KVM: Report IRQ injection status to userspace.
KVM: MMU: remove assertion in kvm_mmu_alloc_page
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (29 commits)
crypto: sha512-s390 - Add missing block size
hwrng: timeriomem - Breaks an allyesconfig build on s390:
nlattr: Fix build error with NET off
crypto: testmgr - add zlib test
crypto: zlib - New zlib crypto module, using pcomp
crypto: testmgr - Add support for the pcomp interface
crypto: compress - Add pcomp interface
netlink: Move netlink attribute parsing support to lib
crypto: Fix dead links
hwrng: timeriomem - New driver
crypto: chainiv - Use kcrypto_wq instead of keventd_wq
crypto: cryptd - Per-CPU thread implementation based on kcrypto_wq
crypto: api - Use dedicated workqueue for crypto subsystem
crypto: testmgr - Test skciphers with no IVs
crypto: aead - Avoid infinite loop when nivaead fails selftest
crypto: skcipher - Avoid infinite loop when cipher fails selftest
crypto: api - Fix crypto_alloc_tfm/create_create_tfm return convention
crypto: api - crypto_alg_mod_lookup either tested or untested
crypto: amcc - Add crypt4xx driver
crypto: ansi_cprng - Add maintainer
...
This file uses PCI MSI defines and so needs pci.h.
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These simple debug statments should be using dev_dbg() instead of
accessing bus_id directly (or they should use device_name).
As bus_id is going away, this patch is necessary.
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The gianfar@25000 node was missing its ranges prop for the mdio bus
and provided an explicit ranges property on gianfar@24000 to match
change from commit:
commit 70b3adbba0
Author: Anton Vorontsov <avorontsov@ru.mvista.com>
Date: Thu Mar 19 21:01:45 2009 +0300
powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
