do { } while(0) is not a good imitation of function returning void;
use ((void)0) instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On 64-bit machines, if an atomic counter is explicitly set to a
negative value, the atomic_dec_if_positive function will decrement and
store the next smallest value in the atomic counter, contrary to its
intended operation.
The comparison to determine if the decrement will make the result
negative was done by the "addic." instruction, which operates on a
64-bit value, namely the zero-extended word loaded from the atomic
variable. This patch uses an explicit word compare (cmpwi) and
changes the addic. to an addi (also changing "=&r" to "=&b" so that r0
isn't used, and addi doesn't become li).
This also fixes a bug for both 32-bit and 64-bit in that previously
0x80000000 was considered positive, since the result after
decrementing is positive. Now it is considered negative.
Also, I clarify the return value in the comments just to make it clear
that the value returned is always the decremented value, even if that
value is not stored back to the atomic counter.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
unionfs managed to hit this on s390. Some architectures use __ptr_t in their
FD_ZERO implementation. We don't have a __ptr_t. Switch them over to plain
old void*.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were a few issues with the HCALL_STATS code:
- PURR cpu feature checks were backwards
- We iterated one entry off the end of the hcall_stats array
- Remove dead update_hcall_stats() function prototype
I noticed one thing while debugging, and that is we call H_ENTER (to set
up the MMU hashtable in early init) before we have done the cpu fixups.
This means we will execute the PURR SPR reads even on a CPU that isnt
capable of it. I wonder if we can move the CPU feature fixups earlier.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using device_initcall makes it happen for every platform that
compiles this file in. This is really bad, for obvious reasons.
Instead, we use the .init field of the machine description. If
the platform needs the hook to do something specific it can provides
its own function and call mpc52xx_declare_of_platform_devices from
there. If not, the mpc52xx_declare_of_platform_devices function can
directly be used as the init hook.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we switched over to the generic BUG mechanism we forgot to change
the assembly code which open-codes a WARN_ON() in enter_rtas(), so the
bug table got corrupted.
This patch provides an EMIT_BUG_ENTRY macro for use in assembly code,
and uses it in entry_64.S. Tested with CONFIG_DEBUG_BUGVERBOSE on ppc64
but not without -- I tried to turn it off but it wouldn't go away; I
suspect Aunt Tillie probably needed it.
This version gets __FILE__ and __LINE__ right in the assembly version --
rather than saying include/asm-powerpc/bug.h line 21 every time which is
a little suboptimal.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Virtually index, physically tagged cache architectures can get away
without cache flushing when forking. This patch adds a new cache
flushing function flush_cache_dup_mm(struct mm_struct *) which for the
moment I've implemented to do the same thing on all architectures
except on MIPS where it's a no-op.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, to tell a task that it should go to the refrigerator, we set the
PF_FREEZE flag for it and send a fake signal to it. Unfortunately there
are two SMP-related problems with this approach. First, a task running on
another CPU may be updating its flags while the freezer attempts to set
PF_FREEZE for it and this may leave the task's flags in an inconsistent
state. Second, there is a potential race between freeze_process() and
refrigerator() in which freeze_process() running on one CPU is reading a
task's PF_FREEZE flag while refrigerator() running on another CPU has just
set PF_FROZEN for the same task and attempts to reset PF_FREEZE for it. If
the refrigerator wins the race, freeze_process() will state that PF_FREEZE
hasn't been set for the task and will set it unnecessarily, so the task
will go to the refrigerator once again after it's been thawed.
To solve first of these problems we need to stop using PF_FREEZE to tell
tasks that they should go to the refrigerator. Instead, we can introduce a
special TIF_*** flag and use it for this purpose, since it is allowed to
change the other tasks' TIF_*** flags and there are special calls for it.
To avoid the freeze_process()-refrigerator() race we can make
freeze_process() to always check the task's PF_FROZEN flag after it's read
its "freeze" flag. We should also make sure that refrigerator() will
always reset the task's "freeze" flag after it's set PF_FROZEN for it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (36 commits)
[POWERPC] Generic BUG for powerpc
[PPC] Fix compile failure do to introduction of PHY_POLL
[POWERPC] Only export __mtdcr/__mfdcr if CONFIG_PPC_DCR is set
[POWERPC] Remove old dcr.S
[POWERPC] Fix SPU coredump code for max_fdset removal
[POWERPC] Fix irq routing on some 32-bit PowerMacs
[POWERPC] ps3: Add vuart support
[POWERPC] Support ibm,dynamic-reconfiguration-memory nodes
[POWERPC] dont allow pSeries_probe to succeed without initialising MMU
[POWERPC] micro optimise pSeries_probe
[POWERPC] Add SPURR SPR to sysfs
[POWERPC] Add DSCR SPR to sysfs
[POWERPC] Fix 440SPe CPU table entry
[POWERPC] Add support for FP emulation for the e300c2 core
[POWERPC] of_device_register: propagate device_create_file return code
[POWERPC] Fix mmap of PCI resource with hack for X
[POWERPC] iSeries: head_64.o needs to depend on lparmap.s
[POWERPC] cbe_thermal: Fix initialization of sysfs attribute_group
[POWERPC] Remove QE header files from lite5200.c
[POWERPC] of_platform_make_bus_id(): make `magic' int
...
Make powerpc's __ilog2_u64() take a 64-bit argument.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes powerpc use the generic BUG machinery. The biggest reports the
function name, since it is redundant with kallsyms, and not needed in general.
There is an overall reduction of code, since module_32/64 duplicated several
functions.
Unfortunately there's no way to tell gcc that BUG won't return, so the BUG
macro includes a goto loop. This will generate a real jmp instruction, which
is never used.
[akpm@osdl.org: build fix]
[paulus@samba.org: remove infinite loop in BUG_ON]
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Hugh Dickens <hugh@veritas.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 85xx we don't build in dcr support because the core doesn't implement the
instructions. This caused problems when building an 85xx kernel. Additionally
made it so we only build __mtdcr/__mfdcr if we are CONFIG_PPC_DCR_NATIVE.
The 85xx build issue wasPointed out by Dai Haruki.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Large sched domains can be very expensive to scan. Add an option SD_SERIALIZE
to the sched domain flags. If that flag is set then we make sure that no
other such domain is being balanced.
[akpm@osdl.org: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Peter Williams <pwil3058@bigpond.net.au>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: "Chen, Kenneth W" <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now we have a SPURR cpu feature bit, we can export it to userspace in
sysfs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
POWER6 adds a new SPR, the data stream control register (DSCR). It can
be used to adjust how agressive the prefetch mechanisms are.
Its possible we may want to context switch this, but for now just export
it to userspace via sysfs so we can adjust it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the grungy swap all the occurrences in the right places patch that
goes with the updates. At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs
If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.
If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)
Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia
[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to sort out our struct termios and add proper speed control we need
to separate the kernel and user termios structures. Glibc is fine but the
other libraries rely on the kernel exported struct termios and we need to
extend this without breaking the ABI/API
To do so we add a struct ktermios which is the kernel view of a termios
structure and overlaps the struct termios with extra fields on the end for
now. (That limitation will go away in later patches). Some platforms (eg
alpha) planned ahead and thus use the same struct for both, others did not.
This just adds the structures but does not use them, it seems a sensible
splitting point for bisect if there are compile failures (not that I expect
them)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide ilog2() fallbacks for powerpc for 32-bit numbers and 64-bit numbers on
ppc64.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The e300c2 has no FPU. Its MSR[FP] is grounded to zero. If an attempt
is made to execute a floating point instruction (including floating-point
load, store, or move instructions), the e300c2 takes a floating-point
unavailable interrupt.
This patch adds support for FP emulation on the e300c2 by declaring a
new CPU_FTR_FP_TAKES_FPUNAVAIL, where FP unavail interrupts are
intercepted and redirected to the ProgramCheck exception path for
correct emulation handling.
(If we run out of CPU_FTR bits we could look to reclaim this bit by adding
support to test the cpu_user_features for PPC_FEATURE_HAS_FPU instead)
It adds a nop to the exception path for 32-bit processors with a FPU.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The powerpc version of pci_resource_to_user() and associated hooks
used by /proc/bus/pci and /sys/bus/pci mmap have been broken for some
time on machines that don't have a 1:1 mapping of devices (basically
on non-PowerMacs) and have PCI devices above 32 bits.
This attempts to fix it as well as possible.
The rule is supposed to be that pci_resource_to_user() always converts
the resources back into a BAR values since that's what the /proc
interface was supposed to deal with. However, for X to work on
platforms where PCI MMIO is not mapped 1:1, it became a habit of
platforms like powerpc to pass "fixed up" values there since X expects
to be able to use values from /proc/bus/pci/devices as offsets to mmap
of /dev/mem...
So we keep that contraption here, causing also /sys/*/resource to
expose fully absolute MMIO addresses instead of BAR values, which is
ugly, but should still work as long as those are only used to calculate
alignment within a page.
X is still broken when built 32 bits on machines where PCI MMIO can be
above 32-bit space unfortunately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To test for the existence of an RTAS function, we typically do:
foo_token = rtas_token("foo");
if (foo_token == RTAS_UNKNOWN_SERVICE)
return;
Add a rtas_service_present method, which provides a more conventional
boolean interface for testing the existence of an RTAS method.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ack_irq macro is unused and conflicts with James' work to template
the generic irq code. mask_irq and unmask_irq are also unused, so delete
those macros too.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current PowerPC code makes pci_unmap_addr(), pci_unmap_addr_set(),
and friends trivial for all 32-bit kernels. This is reasonable, since
for those kernels it is true that pci_unmap_single() does not need the
DMA address from the original DMA mapping -- in fact, it is a NOP.
However, I recently tried the tg3 driver on a PowerPC 440SPe machine,
which runs a 32-bit kernel and has non-cache-coherent PCI DMA. I
found that the tg3 driver crashed in pci_dma_sync_single_for_cpu(),
since for non-coherent systems, that function must invalidate the
cache for the DMA address range requested, and therefore it does use
the address passed in. tg3 uses a DMA address it stashes away with
pci_unmap_addr_set() and retrieves with pci_unmap_addr(). Of course,
since pci_unmap_addr() is defined to (0) right now, this doesn't work.
It seems to me that the tg3 driver is using pci_unmap_addr() in a
legitimate way -- I wouldn't want to have to teach all drivers that
they should use pci_unmap_addr() if they only need the address for
unmapping functions, but if they want the pci_dma_sync functions, then
they have to store the DMA address without the helper macros.
The right fix therefore seems to be in the definition of the macros in
<asm/pci.h> -- we should use the trivial versions only for 32-bit
kernels for coherent systems, and the real versions for both 64-bit
kernels and non-coherent systems.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It uses #ifdef __KERNEL__, so needs to be processed with unifdef.
Signed-off-by: Arnd Bergann <arnd.bergmann@de.ibm.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move pSeries_mach_cpu_die() into platforms/pseries/hotplug-cpu.c,
this allows rtas_stop_self() to be static so remove the prototype.
Wire up pSeries_mach_cpu_die() in the initcall, rather than statically
in setup.c, the initcall will still run prior to the cpu hotplug code
being callable, so there should be no change in behaviour.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the contents of the userspace asm/setup.h header consistent on all
architectures:
- export setup.h to userspace on all architectures
- export only COMMAND_LINE_SIZE to userspace
- frv: move COMMAND_LINE_SIZE from param.h
- i386: remove duplicate COMMAND_LINE_SIZE from param.h
- arm:
- export ATAGs to userspace
- change u8/u16/u32 to __u8/__u16/__u32
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass struct dev pointer to dma_cache_sync()
dma_cache_sync() is ill-designed in that it does not have a struct device
pointer argument which makes proper support for systems that consist of a
mix of coherent and non-coherent DMA devices hard. Change dma_cache_sync
to take a struct device pointer as first argument and fix all its callers
to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dma_is_consistent() is ill-designed in that it does not have a struct
device pointer argument which makes proper support for systems that consist
of a mix of coherent and non-coherent DMA devices hard. Change
dma_is_consistent to take a struct device pointer as first argument and fix
the sole caller to pass it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define elf_addr_t in linux/elf.h. The size of the type is determined using
ELF_CLASS. This allows us to remove the defines that today are spread all
over .c and .h files.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Cc: Daniel Jacobowitz <drow@false.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last thing we agreed on was to remove the macros entirely for 2.6.19,
on all architectures. Unfortunately, I think nobody actually _did_ that,
so they are still there.
[akpm@osdl.org: x86_64 fix]
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Schafer <gschafer@zip.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce pagefault_{disable,enable}() and use these where previously we did
manual preempt increments/decrements to make the pagefault handler do the
atomic thing.
Currently they still rely on the increased preempt count, but do not rely on
the disabled preemption, this might go away in the future.
(NOTE: the extra barrier() in pagefault_disable might fix some holes on
machines which have too many registers for their own good)
[heiko.carstens@de.ibm.com: s390 fix]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Nick Piggin <npiggin@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_LBD and CONFIG_LSF are spread into asm/types.h for no particularly
good reason.
Centralising the definition in linux/types.h means that arch maintainers
don't need to bother adding it, as well as fixing the problem with
x86-64 users being asked to make a decision that has absolutely no
effect.
The H8/300 porters seem particularly confused since I'm not aware of any
microcontrollers that need to support 2TB filesystems.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove CPU_FTR_16M_PAGE from the cupfeatures mask at runtime on iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds utility routines used by 52xx device drivers and board support
code. Main functionality is to add device nodes to the of_platform_bus,
retrieve the IPB bus frequency, and find+ioremap device registers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no need to expose these settings outside the scope
of the interrupt controller code itself.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow arch/powerpc/kernel/crash.c to build on 32-bit we need a
definition of hard_irq_disable(). 32-bit doesn't support the lazy
interrupt disabling mechanism, so on 32-bit hard_irq_disable() is
simply local_irq_disable(). Add a definition for hard_irq_enable()
just for completeness.
This allows (KEXEC=y && PPC32=y) to build again. Broken since
d04c56f73c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
"extern inline" generates a warning with -Wmissing-prototypes and I'm
currently working on getting the kernel cleaned up for adding this to
the CFLAGS since it will help us to avoid a nasty class of runtime
errors.
If there are places that really need a forced inline, __always_inline
would be the correct solution.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At least the ide driver calls pcibus_to_node, which is not
defined when CONFIG_PCI is disabled. This adds a nop function
for the !PCI case.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
A few code paths need to check whether or not they are running
on the PS3's LV1 hypervisor before making hcalls. This introduces
a new firmware feature bit for this, FW_FEATURE_PS3_LV1.
Now when both PS3 and IBM_CELL_BLADE are enabled, but not PSERIES,
FW_FEATURE_PS3_LV1 and FW_FEATURE_LPAR get enabled at compile time,
which is a bug. The same problem can also happen for (PPC_ISERIES &&
!PPC_PSERIES && PPC_SOMETHING_ELSE). In order to solve this, I
introduce a new CONFIG_PPC_NATIVE option that is set when at least
one platform is selected that can run without a hypervisor and then
turns the firmware feature check into a run-time option.
The new cell oprofile support that was recently merged does not
work on hypervisor based platforms like the PS3, therefore make
it depend on PPC_CELL_NATIVE instead of PPC_CELL. This may change
if we get oprofile support for PS3.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
When renaming CONFIG_PS3 to CONFIG_PPC_PS3, a few occurrences have been
missed.
I also fixed up the alignment in arch/powerpc/platforms/Makefile.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It may be desireable to build a kernel for cell without
spufs, e.g. as the initial kboot kernel. This requires
that the SPU specific parts of the core dump and the xmon
code depend on CONFIG_SPU_BASE instead of CONFIG_PPC_CELL.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds a PS3 system bus driver. This system bus is a virtual bus used to present
the PS3 system devices in the LDM.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds some needed bits for a config option PS3_USE_LPAR_ADDR that disables
the PS3 lpar address translation mechanism. This is a currently needed
workaround for limitations in the design of the generic cell spu support.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
