iIDMA (Intelligent Interleaved Direct Memory Access) allows for
the HBA hardware to send FC frames at the rate at which they can
be received by a target device. By taking advantage of the
higher link rate, the HBA can maximize bandwidth utilization in a
heterogeneous multi-speed SAN.
Within a fabric topology, port speed detection is done via a Name
Server command (GFPN_ID) followed by a Fabric Management command
(GPSC). In an FCAL/N2N topology, port speed is based on the HBA
link-rate.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently it is impossible to reset provided by Qlogic QLA2xxx driver
SCSI devices externally using corresponding sg devices, particularly via
sg_reset utility, because qla2xxx driver in qla2xxx_eh_device_reset()
function checks if the input scsi_cmnd has its private data (CMD_SP())
attached. Then the found pointer isn't used anywhere inside of
qla2xxx_eh_device_reset(). If the RESET request comes from sg device, it
doesn't have such private data.
The attached patch removes check for non-NULL CMD_SP() from
qla2xxx_eh_device_reset(), hence allows to reset QLA2xxx's devices using
corresponding sg devices.
AV: change applies to bus/host reset handlers as well.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a few spaces to MODULE_PARM_DESC() text for qla2xxx. Without these
spaces text runs together when modinfo prints the text.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/aacraid/comminit.c
Fixed up by removing the now renamed CONFIG_IOMMU option from
aacraid
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code incorrectly assigned it to the driver's
link-down-timeout value (a value in seconds).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove qla2xxx_probe_one/qla2xxx_remove_one stubs previously
used with external firmware module loaders.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As there is no point in failing the initialization process when
firmware informs the host software that it could not transition
beyond a CONFIG_WAIT nor WAIT_FOR_LOGIN state. Previous logic
would mark such conditions as a general *failure* and subsequently
tear-down the scsi-host during initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- macro usage statements should terminate with a ';'
- remove unused macros.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The host section of ISP24xx NVRAMs contain a new bit which
allows a user to selectively disable ports of an HBA. These
ports (hosts) will not be presented to the midlayer.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semantic changes in ISP24xx firmware behaviour inadvertently
caused the driver to believe an F-port topology was present in an
N_port-to-N_port configuration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify and centralise buffer allocation/deallocation, as
there's no point in having two memory request methods.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Expandind on the previous commit:
commit 79f89a4296
Author: andrew.vasquez@qlogic.com <andrew.vasquez@qlogic.com>
Date: Fri Jan 13 17:05:58 2006 -0800
[SCSI] qla2xxx: Disable port-type RSCN handling via driver state-machine.
and given:
- the process-context requirements of the FC transport
rport-APIs.
- lack of port-type RSCN processing logic for ISP24xx and newer
chips.
it's time now to remove the state-machine logic from mainline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In qla2x00_reset_chip the driver first takes the hardware lock,
and then later on takes the mbx lock.
In the mailbox_command code.. it goes the other way around.
Discovered with the lock validator.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If firmware image is unavailable via request_firwmare(), then
attempt to load the image (likely out-of-date) stored in flash
memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With ISP24XX and ISP54XX parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one() fails before calling request_irq() but gets to
qla2x00_free_device() then it will mistakenly try to free an irq it didn't
request. It's chosing to free based on ha->pdev->irq which is always set.
host->irq is set after request_irq() succeeds so let's use that to decide
to free or not.
This was observed and tested when a silly set of circumstances lead to
firmware loading failing on a 2100.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ISP24XX FW does not support Mbx 0x74 ie Login Local Port.
Added the equivalent code for ISP24XX ie to relogin in non
fabric case for ISP24XX use login iocb.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
