SRAM size fix for HS/EMU devices
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_type() function is added and returns the DEVICETYPE field of
the CONTROL_STATUS register. The result can be used for conditional
code based on whether device is GP (general purpose), EMU or
HS (high security). Also move the type defines so omap1 code
compile does not require ifdefs for sections using these defines.
This code is needed for the following fix to set the SRAM
size correctly for HS omaps. Also at least PM and watchdog
code will need this function.
Signed-off-by: Kevin Hilman <khilman@ti.deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Program the SDRC_MR_0 register as well during SDRC clock changes.
This register allows selection of the memory CAS latency. Some SDRAM
chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency
at lower clock rates.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2
divider, add a short delay before returning to SDRAM to allow the SDRC
time to stabilize. Without this delay, the system is prone to random
panics upon re-entering SDRAM.
This time delay varies based on MPU frequency. At 500MHz MPU frequency at
room temperature, 64 loops seems to work okay; so add another 32 loops for
environmental and process variation.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
This patch adds SMP platform specific parts for local(mpu) timer support
for OMAP4430 platform. Each Cortex-a9 core has it's own local timer in the
MPU domain. These timers are not in wakeup domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds SMP platform files support for OMAP4430SDP. TI's OMAP4430
SOC is based on ARM Cortex-A9 SMP architecture. It's a dual core SOC
with GIC used for interrupt handling and SCU for cache coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the Makefile and Kconfig entries for OMAP4. The OMAP4430 SDP
board file supports only minimal set of drivers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch update the common clock.c file for OMAP4. The clk_get() and
clk_put() functions are moved to common place in arch/arm/common/clkdev.c
Since on current OMAP4 platform clk management is still not supported, the
platform file is stubbed with those functions.
Once the framework is ready, this WILL be replaced with a full
clkdev implementation.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the support for OMAP4. The platform and machine specific
headers and sources updated for OMAP4430 SDP platform.
OMAP4430 is Texas Instrument's SOC based on ARM Cortex-A9 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are not being used right now, and the processor specific
defines should be used instead by any code accessing these registers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make 770 LCD work by adding clk_add_alias().
Also remove the old unused functions.
Note that the clk_add_alias() could probably be moved
to arch/arm/clkdev.c later on.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com
Convert the board-rx51 smc91x code to be generic and make
the boards to use it. This allows future recalculation of the
timings when the source clock gets scaled.
Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL.
Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing
calculations.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add generic onenand support when connected to GPMC and make the
boards to use it.
The patch has been modified to make it more generic to support all
the boards with GPMC. The patch also remove unused prototype for
omap2_onenand_rephase(void).
Note that board-apollon.c is currently using the MTD_ONENAND_GENERIC
and setting the GPMC timings in the bootloader. Setting the GPMC
timings in the bootloader will not allow supporting frequency
scaling for the onenand source clock.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Original OMAP DMA chaining design had chain_id as one of the callback
parameters. Patch 538528de0c changed it
to use logical channel instead.
Correct the naming for callback to also use logical channel number
instead of the chain_id.
More details are on this email thread:
http://marc.info/?l=linux-omap&m=122961071931459&w=2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement transparent copy and constant fill features for OMAP2/3.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add common omap2/3 function to check wether there is irq pending.
Switch to use it in omap2 pm code instead of its own.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes unnecessary omap2_globals and pass the global structures
directly as function argument.
The proposed cleanup was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes fixes omap_sram_error() function and replace the
error paths with BUG_ON.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the compiler warning "assignment from incompatible
pointer type" in dmtimer.c and removes the tye casts. These warnings
were suppressed by type catsing.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
This email address is going to expire soon so update it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If XSYNCERR or RSYNCERR interrupts are enabled, they are never
cleared causing the IRQ handler to be continuously called.
This patch clears the IRQs in question in the event they are
enabled and taken.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This increases VMALLOC_END to 0x18000000, making room for 256MB
RAM with the default 128MB vmalloc region.
Note that after this patch there's no longer a hole between vmalloc
space and the beginning of IO space on omap2 as the first virtual
mapping starts at 0xd8000000.
Also fold in a related change from Paul Walmsley <paul@pwsan.com>
to change the OMAP2_SRAM addresses accordingly.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes unnecessary omap2_globals and pass the global structures
directly as function argument.
The proposed cleanup was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes fixes omap_sram_error() function and replace the
error paths with BUG_ON.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the compiler warning "assignment from incompatible
pointer type" in dmtimer.c and removes the tye casts. These warnings
were suppressed by type catsing.
The proposed fix was suggested by Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove OMAP_PRM_REGADDR and use processor specific defines instead.
Also fold in a patch from Kevin Hilman to add _OFFSET #defines
for the PRCM registers to be used with the prm_[read|write]_* macros.
These are used extensively in the forthcoming OMAP PM support.
Also remove now unused OMAP2_PRM_BASE.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use processor specific defines instead.
As an extra bonus, this patch fixes the problem of CONFIG_DEBUG_SPINLOCK
calling sched_clock before we have things initialized:
http://patchwork.kernel.org/patch/15810/
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch provides a device drivers, which has a omap iommu, with
address mapping APIs between device virtual address(iommu), physical
address and MPU virtual address.
There are 4 possible patterns for iommu virtual address(iova/da) mapping.
|iova/ mapping iommu_ page
| da pa va (d)-(p)-(v) function type
---------------------------------------------------------------------------
1 | c c c 1 - 1 - 1 _kmap() / _kunmap() s
2 | c c,a c 1 - 1 - 1 _kmalloc()/ _kfree() s
3 | c d c 1 - n - 1 _vmap() / _vunmap() s
4 | c d,a c 1 - n - 1 _vmalloc()/ _vfree() n*
'iova': device iommu virtual address
'da': alias of 'iova'
'pa': physical address
'va': mpu virtual address
'c': contiguous memory area
'd': dicontiguous memory area
'a': anonymous memory allocation
'()': optional feature
'n': a normal page(4KB) size is used.
's': multiple iommu superpage(16MB, 1MB, 64KB, 4KB) size is used.
'*': not yet, but feasible.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
As per 3430 TRM, there are 6 banks [0 to 191]
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Mark the SRAM (aka OCM RAM) as Non-cacheable Normal memory[1]. This
is to prevent the ARM from evicting existing cache lines to SDRAM
while code is executing from the SRAM. Necessary since one of the
primary uses for the SRAM is to hold the code and data for the CORE
DPLL M2 divider reprogramming code, which must execute while the SDRC
is idled. If the ARM attempts to write cache lines back to the while
the SRAM code is running, the ARM will stall[2].
TI deals with this problem in the CDP kernel by marking the SRAM as
Strongly-ordered memory.
Tero Kristo <tero.kristo@nokia.com> caught a bug in an earlier version of
this patch - thanks Tero.
...
1. ARMv7 ARM (DDI 0406A) pp. A3-30, A3-31, B3-32.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Print reserved memory only if it was actually reserved.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The structure 'arch_mmu' accommodates the difference between omap1 and
omap2/3.
This patch provides omap2/3 specific functions
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
omap mailbox uses rq->data as the second opaque pointer to carry
mbox_msg_t and rq->special message argument which is needed only for
tx. Add and use omap_msg_tx_data struct for tx and use rq->special
for mbox_msg_t for rx such that only rq->special is used as opaque
pointer.
[ Impact: cleanup rq->data usage, extra kmalloc in msg_send ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion. Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.
This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request. BUG_ON() is added to to ensure that
this actually happens.
Most conversions are simple but there are a few noteworthy ones.
* cdrom/viocd: viocd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/block/dasd: dasd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/char/tape_block: tapeblock_end_request() replaced with direct
calls to blk_end_request_all().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
All GP timers on OMAP2/3 can generate wakeup events. The wakeup status is
cleared in the PRCM interrupt handler.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Flush posted write to IRQSTATUS register in GPIO IRQ handler.
This eliminates the below error for all peripherals that use GPIO interrupts.
<4>Spurious irq 95: 0xffffffdf, please flush posted write for irq 31
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO IRQ enable/disable path attempts to also enable IRQ wake
support for the parent GPIO bank IRQ as well. However, since there is
no 'set_wake' hook for the bank IRQs, these calls will always fail.
Also, since the enable will fail on the suspend path, the disable on
the resume path will trigger unbalanced enable/disable warnings.
This was discovered in the suspend/resume path on OMAP3/Beagle using
the gpio-keys driver which disables/re-enables GPIO IRQ wakeups in the
suspend/resume path.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no anymore legacy driver for OMAP24XX Enhanced Audio Controller
in linux-omap and it was newer in mainline so cleanup these unneeded
defines and initialization code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the possible race condition in omap_free_dma(). Function omap_free_dma()
sets the dev_id = -1 and then accesses the channel afterwards to clear it.
But setting the dev_id=-1 makes the channel available for allocation again.
So it is possible someone else can grab it and results are unpredictable.
To avod this DMA channle is cleared first and then the dev_id = -1 is set.
Thanks to McNeil, Sean <sean.mcneil@ti.com> for ointing out this issue.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3f0a820c4c breaks OMAP2xxx boot
during initial propagate_rate() on osc_ck and sys_ck. Fix by
pre-initializing all struct clks before running any other clock init
code. Incorporates review comments from Russell King
<rmk+kernel@arm.linux.org.uk>.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 00000000
<1>pgd = c0004000
<1>[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #37)
PC is at propagate_rate+0x10/0x60
LR is at omap2_clk_init+0x30/0x218
...
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP34XX_MAILBOX_BASE must be defined both for 24xx and 34xx.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a generic board-file for initializing usb
on omap2430 and omap3 boards.
Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When setting up HSMMC devices, pass the device nodes back so
board code can linking them to their power supply regulators.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds several new GPIO pins and updates
the pin naming comments.
The patch is based on earlier patches on linux-omap
list by Manikandan Pillai <mani.pillai@ti.com>,
Vaibhav Hiremath <hvaibhav@ti.com> and
David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the spurious interrupt issue on a DMA channel.
In OMAP sDMA, contrast to the SDMA.DMA4_CSRi registers, the
SDMA.DMA4_IRQSTATUS_Lj registers are updated regardless of
the corresponding bits in the SDMA.DMA4_IRQENABLE_Lj registers.
Since there are four sDMA interrupt lines and if more than one
line is actively used by two concurrently running sDMA softwares
modules,then the spurious interrupt can be observed on the other
lines.
Fix in this patch will only dispatch the relevant and enabled
interrupts on a particular line thus perevting spurious IRQ.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch set up a cmdline option for omap dma for masking the
available channels. It is needed since the OMAP DMA is a system wide
resource and can be used by another software apart from the kernel.
To reserve the omap SDMA channels for kernel dma usage, use cmdline
bootarg "omap_dma_reserve_ch=". The valid range is 1 to 32.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch extends command line option "i2c_bus=bus_id,clkrate" so that
it allow to register additional I2C busses that are not registered with
omap_register_i2c_bus from board initialization code.
Purpose of this is to register additional board busses which are routed
to external connectors only without any on board I2C devices.
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a new command line option "i2c_bus=bus_id,clkrate" into
I2C bus registration helper. Purpose of the option is to override the
default board specific bus speed which is supplied by the
omap_register_i2c_bus.
The default bus speed is typically set to speed of slowest I2C chip on the
bus and overriding allow to use some experimental configurations or updated
chip versions without any kernel modifications.
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the dmtimer function symbols available so modules can take use of
them.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also remove board-omap3beagle.h that is not included anywhere,
and move protoype for voiceblue_reset() from board-voiceblue.h
to system.h.
After this patch there are still board-ams-delta.h, board-sx1.h
and board-voiceblue.h that export some functions. These could
be removed if the functions were moved under drivers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP34XX_ETHR_START to LDP_ETHR_START.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP24XX_ETHR_GPIO_IRQ to H4_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
SDP2430_ETHR_GPIO_IRQ to SDP2430_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since "mbox->dev" doesn't exist and isn't created either at
registration, this patch will create "struct device", which belongs to
"omap-mailbox" class and set this pointer for the member of
"struct omap_mbox".
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a machine class has a custom __virt_to_bus() implementation then it
must provide a __arch_page_to_dma() implementation as well which is
_not_ based on page_address() to support highmem.
This patch fixes existing __arch_page_to_dma() and provide a default
implementation otherwise. The default implementation for highmem is
based on __pfn_to_bus() which is defined only when no custom
__virt_to_bus() is provided by the machine class.
That leaves only ebsa110 and footbridge which cannot support highmem
until they provide their own __arch_page_to_dma() implementation.
But highmem support on those legacy platforms with limited memory is
certainly not a priority.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Fixes a linker error when OMAP I2C bus driver is compiled as a module:
ERROR: "i2c_register_board_info" [arch/arm/plat-omap/i2c.ko] undefined!
The I2C utility functions used for board initialization should be always
built-in.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After my OMAP3 board has been running for a while, I'm seeing weird
latency traces like this:
sh-1574 0d.h2 153us : do_timer (tick_do_update_jiffies64)
sh-1574 0d.h2 153us : update_wall_time (do_timer)
sh-1574 0d.h2 153us!: omap_32k_read (update_wall_time)
sh-1574 0d.h2 1883us : update_xtime_cache (update_wall_time)
sh-1574 0d.h2 1883us : clocksource_get_next (update_wall_time)
sh-1574 0d.h2 1883us+: _spin_lock_irqsave (clocksource_get_next)
and after a while:
sh-17818 0d.h3 153us : do_timer (tick_do_update_jiffies64)
sh-17818 0d.h3 153us : update_wall_time (do_timer)
sh-17818 0d.h3 153us!: omap_32k_read (update_wall_time)
sh-17818 0d.h3 1915us : update_xtime_cache (update_wall_time)
sh-17818 0d.h3 1915us+: clocksource_get_next (update_wall_time)
sh-17818 0d.h3 1945us : _spin_lock_irqsave (clocksource_get_next)
Turns out that sched_clock() is using cyc2ns(), which returns NTP
adjusted time. The sched_clock() frequency should not be adjusted. The
patch deletes omap_32k_ticks_to_nsecs() and rewrites sched_clock()
to do the conversion using the constant multiplier.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Richard Woodruff writes:
| The historic usage of this has been against single use leaf clocks
| (1st instance of gptimer). When it was used it did:
| clk_get()
| clk_set_parent()
| clk_enable()
|
| This usage was ok for that. Use on a disabled clock is needed.
|
| If there are multiple users on the clock or it is enabled there are
| problems.
|
| The call can still be unfriendly if 2 different drivers are using the
| clock with their own clock get/enable. It might be the function should
| return an error if usecount != 0 to stop surprises. It is all around
| better if the parenting is done when the clock is off.
This is a good reason to ensure that the clock is not enabled when
clk_set_parent() is called.
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some OMAP3 chip behaviors change in ES levels after ES2. Modify the
existing omap_chip flags to add options for ES3.0 and ES3.1.
Add a new macro, CHIP_GE_OMAP3430ES2, to cover ES levels from ES2
onwards - a common pattern for OMAP3 features. Update all current
users of the omap_chip macros to use this new macro.
Also add CHIP_GE_OMAP3430ES3_1 to cover the USBTLL SAR errata case
(described and fixed in the following patch)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This roughly corresponds with OMAP commits: 7d06c48, 3241b19,
88b5d9b, 18a5500, 9c909ac, 5c6497b, 8b1f0bd, 2ac1da8.
For both OMAP2 and OMAP3, we note the reference and bypass clocks in
the DPLL data structure. Whenever we modify the DPLL rate, we first
ensure that both the reference and bypass clocks are enabled. Then,
we decide whether to use the reference and DPLL, or the bypass clock
if the desired rate is identical to the bypass rate, and program the
DPLL appropriately. Finally, we update the clock's parent, and then
disable the unused clocks.
This keeps the parents correctly balanced, and more importantly ensures
that the bypass clock is running whenever we reprogram the DPLL. This
is especially important because the procedure for reprogramming the DPLL
involves switching to the bypass clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
linux-omap source commit 33d000c99ee393fe2042f93e8422f94976d276ce
introduces a way to "dry run" clock changes before they're committed.
However, this involves putting logic to handle this into each and
every recalc function, and unfortunately due to the caching, led to
some bugs.
Solve both of issues by making the recalc methods always return the
clock rate for the clock, which the caller decides what to do with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This function is race-prone and mistakenly conveys the impression to
drivers that it is part of the clock interface. Get rid of it: core
code that absolutely needs this can just check clk->usecount. Drivers
should not use it at all.
linux-omap source commit is 5df9e4adc2f6a6d55aca53ee27b8baad18897c05.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Traditionally, we've tracked the parent/child relationships between
clk structures by setting the child's parent member to point at the
upstream clock. As a result, when decending the tree, we have had
to scan all clocks to find the children.
Avoid this wasteful scanning by keeping a list of the clock's children.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements the remainder of:
OMAP clock: move rate recalc, propagation code up to plat-omap/clock.c
from Paul Walmsley which is not covered by the previous:
[ARM] omap: move clock propagation into core omap clock code
[ARM] omap: remove unnecessary calls to propagate_rate()
[ARM] omap: move propagate_rate() calls into generic omap clock code
commits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to
mach-omap2/sdrc.c. Rename the OMAP2xxx-specific functions to use an
'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the
function names rather than "memory." Mark several functions
as static that should not be used outside the sdrc2xxx.c file.
linux-omap source commit is bf1612b9d8d29379558500cd5de9ae0367c41fc4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the contents of the arch/arm/mach-omap2/memory.h file to the
existing mach/sdrc.h file, and remove memory.h. Modify files which
include memory.h to include asm/arch/sdrc.h instead.
linux-omap source commit is e7ae2d89921372fc4b9712a32cc401d645597807.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes booting, and is a step toward fixing things properly:
- Make enable_reg u32 instead of u16
[rmk: virtual addresses are void __iomem *, not u32]
- Get rid of VIRTUAL_IO_ADDRESS for clocks
- Use __raw_read/write instead of omap_read/write for clock registers
This patch adds a bunch of compile warnings until omap1 clock
also uses offsets.
linux-omap source commit is 9d1dff8638c9e96a401e1885f9948662e9ff9636.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DPLL FREQSEL jitter correction bits are set based on a table in
the 34xx TRM, Table 4-38, according to the DPLL's internal clock
frequency "Fint." Several Fint frequency ranges are missing from this
table. Previously, we allowed these Fint frequency ranges to be
selected in the rate rounding code, but did not change the FREQSEL bits.
Correspondence with the OMAP hardware team indicates that Fint values
not in the table should not be used. So, prevent them from being
selected during DPLL rate rounding. This removes warnings and also
can prevent the chip from locking up.
The first pass through the rate rounding code will update the DPLL max
and min dividers appropriately, so later rate rounding passes will run
faster than the first.
Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
linux-omap source commit is f9c1b82f55b60fc39eaa6e7aa1fbe380c0ffe2e9.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert struct dpll_data.idlest_bit field to idlest_mask. Needed since
OMAP2 uses two bits for DPLL IDLEST rather than one.
While here, add the missing idlest_* fields for DPLL3.
linux-omap source commits are 25bab0f176b0a97be18a1b38153f266c3a155784
and b0f7fd17db2aaf8e6e9a2732ae3f4de0874db01c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clockdomains for the CM and PRM. These will ultimately replace the
"wkup_clkdm", which appears to not actually exist on the hardware.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
struct clockdomain contains a struct powerdomain *pwrdm and const char
*pwrdm_name. The pwrdm_name is only used at initialization to look up
the appropriate pwrdm pointer. Combining these into a union saves
about 100 bytes on 3430SDP. This patch should not cause any change in
kernel function.
Updated to gracefully handle autodeps that contain invalid powerdomains,
per Russell King's review comments.
Boot-tested on BeagleBoard ES2.1.
linux-omap source commit is 718fc6cd4db902aa2242a736cc3feb8744a4c71a.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a CPUfreq frequency-table implementation for OMAP2 by
walking the PRCM rate-table for available entries and adding them to a
CPUfreq table.
CPUfreq can then be used to manage switching between all the available
entries in the PRCM rate table. Either use the CPUfreq sysfs
interface directly, (see Section 3 of Documentation/cpu-freq/user-guide.txt)
or use the cpufrequtils package:
http://www.kernel.org/pub/linux/utils/kernel/cpufreq/cpufrequtils.html
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Updated to try to use cpufreq_table if it exists.
linux-omap source commit is 77ce544fa48deb7a2003f454624e3ca10d37ab87.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse & checkpatch warnings in OMAP2/3 PRCM & PM code. This mostly
consists of:
- converting pointer comparisons to integers in form similar to
(ptr == 0) to the standard idiom (!ptr)
- labeling a few non-static private functions as static
- adding prototypes for *_init() functions in the appropriate header
files, and getting rid of the corresponding open-coded extern
prototypes in other C files
- renaming the variable 'sclk' in mach-omap2/clock.c:omap2_get_apll_clkin
to avoid shadowing an earlier declaration
Clean up checkpatch issues. This mostly involves:
- converting some asm/ includes to linux/ includes
- cleaning up some whitespace
- getting rid of braces for conditionals with single following statements
Also take care of a few odds and ends, including:
- getting rid of unlikely() and likely() - none of this code is particularly
fast-path code, so the performance impact seems slim; and some of those
likely() and unlikely() indicators are probably not as accurate as the
ARM's branch predictor
- removing some superfluous casts
linux-omap source commit is 347df59f5d20fdf905afbc26b1328b0e28a8a01b.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add non-CORE DPLL rate set code and M,N programming for OMAP3.
Connect it to OMAP34xx DPLLs 1, 2, 4, 5 via the clock framework.
You may see some warnings on rate sets from the freqsel code. The
table that TI presented in the 3430 TRM Rev F does not cover Fint <
750000, which definitely occurs in practice. However, the lack of this
freqsel case does not appear to impair the DPLL rate change.
linux-omap source commit is 689fe67c6d1ad8f52f7f7b139a3274b79bf3e784.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This stops things blowing up if a 'struct clk' to be passed more
than once to clk_register(), which will be required when we decouple
struct clk's from their names.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It makes no sense to have the CKCTL rate selection implemented as a flag
and a special exception in the top level set_rate/round_rate methods.
Provide CKCTL set_rate/round_rate methods, and use these for where ever
RATE_CKCTL is used and they're not already overridden. This allows us
to remove the RATE_CKCTL flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion. So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the clock propagation calls for set_parent and set_rate into
the core omap clock code, rather than having these calls scattered
throughout the OMAP1 and OMAP2 implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
