[ Upstream commit 69f2c9346313ba3d3dfa4091ff99df26c67c9021 ]
Commit 2dc0b46b5e ("libata: sata_down_spd_limit should return if
driver has not recorded sstatus speed") changed the behavior of
sata_down_spd_limit() to return doing nothing if a drive does not report
a current link speed, to avoid reducing the link speed to the lowest 1.5
Gbps speed.
However, the change assumed that a speed was recorded before probing
(e.g. before a suspend/resume) and set in link->sata_spd. This causes
problems with adapters/drives combination failing to establish a link
speed during probe autonegotiation. One example reported of this problem
is an mvebu adapter with a 3Gbps port-multiplier box: autonegotiation
fails, leaving no recorded link speed and no reported current link
speed. Probe retries also fail as no action is taken by sata_set_spd()
after each retry.
Fix this by returning early in sata_down_spd_limit() only if we do have
a recorded link speed, that is, if link->sata_spd is not 0. With this
fix, a failed probe not leading to a recorded link speed is retried at
the lower 1.5 Gbps speed, with the link speed potentially increased
later on the second revalidate of the device if the device reports
that it supports higher link speeds.
Reported-by: Marius Dinu <marius@psihoexpert.ro>
Fixes: 2dc0b46b5e ("libata: sata_down_spd_limit should return if driver has not recorded sstatus speed")
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Marius Dinu <marius@psihoexpert.ro>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37e14e4f3715428b809e4df9a9958baa64c77d51 ]
Since kernel 5.3.4 my laptop (ICH8M controller) does not see Kingston
SV300S37A60G SSD disk connected into a SATA connector on wake from
suspend. The problem was introduced in c312ef1763 ("libata/ahci: Drop
PCS quirk for Denverton and beyond"): the quirk is not applied on wake
from suspend as it originally was.
It is worth to mention the commit contained another bug: the quirk is
not applied at all to controllers which require it. The fix commit
09d6ac8dc5 ("libata/ahci: Fix PCS quirk application") landed in 5.3.8.
So testing my patch anywhere between commits c312ef1763 and
09d6ac8dc5 is pointless.
Not all disks trigger the problem. For example nothing bad happens with
Western Digital WD5000LPCX HDD.
Test hardware:
- Acer 5920G with ICH8M SATA controller
- sda: some SATA HDD connnected into the DVD drive IDE port with a
SATA-IDE caddy. It is a boot disk
- sdb: Kingston SV300S37A60G SSD connected into the only SATA port
Sample "dmesg --notime | grep -E '^(sd |ata)'" output on wake:
sd 0:0:0:0: [sda] Starting disk
sd 2:0:0:0: [sdb] Starting disk
ata4: SATA link down (SStatus 4 SControl 300)
ata3: SATA link down (SStatus 4 SControl 300)
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out
ata1: FORCE: cable set to 80c
ata5: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 4 SControl 300)
ata3: SATA link down (SStatus 4 SControl 300)
ata3.00: disabled
sd 2:0:0:0: rejecting I/O to offline device
ata3.00: detaching (SCSI 2:0:0:0)
sd 2:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_NO_CONNECT
driverbyte=DRIVER_OK
sd 2:0:0:0: [sdb] Synchronizing SCSI cache
sd 2:0:0:0: [sdb] Synchronize Cache(10) failed: Result:
hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 2:0:0:0: [sdb] Stopping disk
sd 2:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET
driverbyte=DRIVER_OK
Commit c312ef1763 dropped ahci_pci_reset_controller() which internally
calls ahci_reset_controller() and applies the PCS quirk if needed after
that. It was called each time a reset was required instead of just
ahci_reset_controller(). This patch puts the function back in place.
Fixes: c312ef1763 ("libata/ahci: Drop PCS quirk for Denverton and beyond")
Signed-off-by: Adam Vodopjan <grozzly@protonmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c38ae56ee034623c59e39c0130ca0dec086c1a39 ]
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'irq', so making 'irq' an int, and change the position to
keep the code format.
./drivers/ata/pata_ixp4xx_cf.c:168:5-8:
WARNING: Unsigned expression compared with zero: irq > 0
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Link: https://lore.kernel.org/r/20210409135426.1773-1-angkery@163.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c76310740807ade5ecdab5888f70ecb6d35732e ]
In the error path in ata_tport_add(), when calling put_device(),
ata_tport_release() is called, it will put the refcount of 'ap->host'.
And then ata_host_put() is called again, the refcount is decreased
to 0, ata_host_release() is called, all ports are freed and set to
null.
When unbinding the device after failure, ata_host_stop() is called
to release the resources, it leads a null-ptr-deref(), because all
the ports all freed and null.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
CPU: 7 PID: 18671 Comm: modprobe Kdump: loaded Tainted: G E 6.1.0-rc3+ #8
pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ata_host_stop+0x3c/0x84 [libata]
lr : release_nodes+0x64/0xd0
Call trace:
ata_host_stop+0x3c/0x84 [libata]
release_nodes+0x64/0xd0
devres_release_all+0xbc/0x1b0
device_unbind_cleanup+0x20/0x70
really_probe+0x158/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0xb4/0x220
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x40
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__pci_register_driver+0x4c/0x60
ahci_pci_driver_init+0x30/0x1000 [ahci]
Fix this by removing redundant ata_host_put() in the error path.
Fixes: 2623c7a5f2 ("libata: add refcounting to ata_host")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 171a93182eccd6e6835d2c86b40787f9f832efaa ]
Clang gives a warning when compiling pata_legacy.c with 'make W=1' about
the 'rt' local variable in pdc20230_set_piomode() being set but unused.
Quite obviously, there is an outb() call missing to write back the updated
variable. Moreover, checking the docs by Petr Soucek revealed that bitwise
AND should have been done with a negated timing mask and the master/slave
timing masks were swapped while updating...
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers.")
Reported-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 979556f1521a835a059de3b117b9c6c6642c7d58 upstream.
'ahci:' is an invalid prefix, preventing the module from autoloading.
Fix this by using the 'platform:' prefix and DRV_NAME.
Fixes: 9e54eae23b ("ahci_imx: add ahci sata support on imx platforms")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c132ea6508b34956e5ed88d04936983ec230601 ]
Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical
from the further AHCI-platform initialization point of view since
exceeding the ports upper limit will cause allocating more resources than
will be used afterwards. But detecting too many child DT-nodes doesn't
seem right since it's very unlikely to have it on an ordinary platform. In
accordance with the AHCI specification there can't be more than 32 ports
implemented at least due to having the CAP.NP field of 5 bits wide and the
PI register of dword size. Thus if such situation is found the DTB must
have been corrupted and the data read from it shouldn't be reliable. Let's
consider that as an erroneous situation and halt further resources
allocation.
Note it's logically more correct to have the nports set only after the
initialization value is checked for being sane. So while at it let's make
sure nports is assigned with a correct value.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ea08aec7e77bfd6599489ec430f9f859ab84575a upstream.
Commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).
The board_ahci_low_power configuration enables support for low power
modes.
This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.
Therefore, when commit 1527f69204fe ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.
The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.
Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.
Fixes: 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3122bf9aa4c974f5e2c0112f799757b3a2779da upstream.
Add the missing command name for ATA_CMD_NCQ_NON_DATA to
ata_get_cmd_name().
Fixes: 661ce1f0c4 ("libata/libsas: Define ATA_CMD_NCQ_NON_DATA")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf476fe22aa1851bab4728e0c49025a6a0bea307 ]
In an unlikely (and probably wrong?) case that the 'ppi' parameter of
ata_host_alloc_pinfo() points to an array starting with a NULL pointer,
there's going to be a kernel oops as the 'pi' local variable won't get
reassigned from the initial value of NULL. Initialize 'pi' instead to
'&ata_dummy_port_info' to fix the possible kernel oops for good...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 72aad489f992871e908ff6d9055b26c6366fb864 upstream.
The {dma|pio}_mode sysfs files are incorrectly documented as having a
list of the supported DMA/PIO transfer modes, while the corresponding
fields of the *struct* ata_device hold the transfer mode IDs, not masks.
To match these docs, the {dma|pio}_mode (and even xfer_mode!) sysfs
files are handled by the ata_bitfield_name_match() macro which leads to
reading such kind of nonsense from them:
$ cat /sys/class/ata_device/dev3.0/pio_mode
XFER_UDMA_7, XFER_UDMA_6, XFER_UDMA_5, XFER_UDMA_4, XFER_MW_DMA_4,
XFER_PIO_6, XFER_PIO_5, XFER_PIO_4, XFER_PIO_3, XFER_PIO_2, XFER_PIO_1,
XFER_PIO_0
Using the correct ata_bitfield_name_search() macro fixes that:
$ cat /sys/class/ata_device/dev3.0/pio_mode
XFER_PIO_4
While fixing the file documentation, somewhat reword the {dma|pio}_mode
file doc and add a note about being mostly useful for PATA devices to
the xfer_mode file doc...
Fixes: d9027470b8 ("[libata] Add ATA transport class")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10d6bdf532902be1d8aa5900b3c03c5671612aa2 ]
of_find_device_by_node() takes reference, we should use put_device()
to release it when not need anymore.
Add missing put_device() to avoid refcount leak.
Fixes: 43f01da0f2 ("MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aafa9f958342db36c17ac2a7f1b841032c96feb4 upstream.
Before detecting the cable type on the dma bar, the driver should check
whether the 'bmdma_addr' is zero, which means the adapter does not
support DMA, otherwise we will get the following error:
[ 5.146634] Bad IO access at port 0x1 (return inb(port))
[ 5.147206] WARNING: CPU: 2 PID: 303 at lib/iomap.c:44 ioread8+0x4a/0x60
[ 5.150856] RIP: 0010:ioread8+0x4a/0x60
[ 5.160238] Call Trace:
[ 5.160470] <TASK>
[ 5.160674] marvell_cable_detect+0x6e/0xc0 [pata_marvell]
[ 5.161728] ata_eh_recover+0x3520/0x6cc0
[ 5.168075] ata_do_eh+0x49/0x3c0
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5399752299396a3c9df6617f4b3c907d7aa4ded8 ]
Samsung' 840 EVO with the latest firmware (EXT0DB6Q) locks up with
the a message: "READ LOG DMA EXT failed, trying PIO" during boot.
Initially this was discovered because it caused a crash
with the sata_dwc_460ex controller on a WD MyBook Live DUO.
The reporter "Tice Rex" which has the unique opportunity that he
has two Samsung 840 EVO SSD! One with the older firmware "EXT0BB0Q"
which booted fine and didn't expose "READ LOG DMA EXT". But the
newer/latest firmware "EXT0DB6Q" caused the headaches.
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7aa8104a554713b685db729e66511b93d989dd6a upstream.
the driver uses libata's "tag" values from in various arrays.
Since the mentioned patch bumped the ATA_TAG_INTERNAL to 32,
the value of the SATA_DWC_QCMD_MAX needs to account for that.
Otherwise ATA_TAG_INTERNAL usage cause similar crashes like
this as reported by Tice Rex on the OpenWrt Forum and
reproduced (with symbols) here:
| BUG: Kernel NULL pointer dereference at 0x00000000
| Faulting instruction address: 0xc03ed4b8
| Oops: Kernel access of bad area, sig: 11 [#1]
| BE PAGE_SIZE=4K PowerPC 44x Platform
| CPU: 0 PID: 362 Comm: scsi_eh_1 Not tainted 5.4.163 #0
| NIP: c03ed4b8 LR: c03d27e8 CTR: c03ed36c
| REGS: cfa59950 TRAP: 0300 Not tainted (5.4.163)
| MSR: 00021000 <CE,ME> CR: 42000222 XER: 00000000
| DEAR: 00000000 ESR: 00000000
| GPR00: c03d27e8 cfa59a08 cfa55fe0 00000000 0fa46bc0 [...]
| [..]
| NIP [c03ed4b8] sata_dwc_qc_issue+0x14c/0x254
| LR [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| Call Trace:
| [cfa59a08] [c003f4e0] __cancel_work_timer+0x124/0x194 (unreliable)
| [cfa59a78] [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| [cfa59a98] [c03d2b3c] ata_exec_internal_sg+0x240/0x524
| [cfa59b08] [c03d2e98] ata_exec_internal+0x78/0xe0
| [cfa59b58] [c03d30fc] ata_read_log_page.part.38+0x1dc/0x204
| [cfa59bc8] [c03d324c] ata_identify_page_supported+0x68/0x130
| [...]
This is because sata_dwc_dma_xfer_complete() NULLs the
dma_pending's next neighbour "chan" (a *dma_chan struct) in
this '32' case right here (line ~735):
> hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_NONE;
Then the next time, a dma gets issued; dma_dwc_xfer_setup() passes
the NULL'd hsdevp->chan to the dmaengine_slave_config() which then
causes the crash.
With this patch, SATA_DWC_QCMD_MAX is now set to ATA_MAX_QUEUE + 1.
This avoids the OOB. But please note, there was a worthwhile discussion
on what ATA_TAG_INTERNAL and ATA_MAX_QUEUE is. And why there should not
be a "fake" 33 command-long queue size.
Ideally, the dw driver should account for the ATA_TAG_INTERNAL.
In Damien Le Moal's words: "... having looked at the driver, it
is a bigger change than just faking a 33rd "tag" that is in fact
not a command tag at all."
Fixes: 28361c4036 ("libata: add extra internal command")
Cc: stable@kernel.org # 4.18+
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f6b0f2d037c8864f20ff15311c695f65eb09db5 ]
The f_CNT register (at the PCI config. address 0x78) is 16-bit, not
8-bit! The bug was there from the very start... :-(
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers.")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d093e02e898b24c58788b0289e3202317a96d2a upstream.
The HPT371 chip physically has only one channel, the secondary one,
however the primary channel registers do exist! Thus we have to
manually disable the non-existing channel if the BIOS hasn't done this
already. Similarly to the pata_hpt3x2n driver, always disable the
primary channel.
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers.")
Cc: stable@vger.kernel.org
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c8ea23d5fa59f28302d4e3370c75d9c308e64410 ]
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5da5231bb47864e5dd6c6731151e98b6ee498827 upstream.
Avoid data corruption by rejecting pass-through commands where
T_LENGTH is zero (No data is transferred) and the dma direction
is not DMA_NONE.
Cc: <stable@vger.kernel.org>
Reported-by: syzkaller<syzkaller@googlegroups.com>
Signed-off-by: George Kennedy<george.kennedy@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a66307d473077b7aeba74e9b09c841ab3d399c2d upstream.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f48394cf1f3e8486591ad98c11cdadb8f1ef2ad upstream.
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8ad7e8cf29eb55836e7a0215f967746ab2b504 upstream.
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5af ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1527f69204fe35f341cb599f1cb01bd02daf4374 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc3 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f971a85439bd25dc7b4d597cf5e4e8dc7ffc884b upstream.
Checking if DMA is enabled should be done via the
ata_dma_enabled helper function, since the init state
0xff indicates disabled.
This meant that ATA_CMD_READ_LOG_DMA_EXT was used and probed
for before DMA was enabled, which caused hangs for some combinations
of controllers and devices.
It might also have caused it to be incorrectly disabled as broken,
but there have been no reports of that.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195895
Signed-off-by: Reimar Döffinger <Reimar.Doeffinger@gmx.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68dbbe7d5b4fde736d104cbbc9a2fce875562012 upstream.
Some ATA drives are very slow to respond to READ_LOG_EXT and
READ_LOG_DMA_EXT commands issued from ata_dev_configure() when the
device is revalidated right after resuming a system or inserting the
ATA adapter driver (e.g. ahci). The default 5s timeout
(ATA_EH_CMD_DFL_TIMEOUT) used for these commands is too short, causing
errors during the device configuration. Ex:
...
ata9: SATA max UDMA/133 abar m524288@0x9d200000 port 0x9d200400 irq 209
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: ATA-9: XXX XXXXXXXXXXXXXXX, XXXXXXXX, max UDMA/133
ata9.00: qc timeout (cmd 0x2f)
ata9.00: Read log page 0x00 failed, Emask 0x4
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: NCQ Send/Recv Log not supported
ata9.00: Read log page 0x08 failed, Emask 0x40
ata9.00: 27344764928 sectors, multi 16: LBA48 NCQ (depth 32), AA
ata9.00: Read log page 0x00 failed, Emask 0x40
ata9.00: ATA Identify Device Log not supported
ata9.00: failed to set xfermode (err_mask=0x40)
ata9: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
ata9.00: configured for UDMA/133
...
The timeout error causes a soft reset of the drive link, followed in
most cases by a successful revalidation as that give enough time to the
drive to become fully ready to quickly process the read log commands.
However, in some cases, this also fails resulting in the device being
dropped.
Fix this by using adding the ata_eh_revalidate_timeouts entries for the
READ_LOG_EXT and READ_LOG_DMA_EXT commands. This defines a timeout
increased to 15s, retriable one time.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0023bb9dd9bc439d44604eeec62426a990054cd upstream.
mv_init_host() propagates the value returned by mv_chip_id() which in turn
gets propagated by mv_pci_init_one() and hits local_pci_probe().
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Since this is a bug rather than a recoverable runtime error we should
use dev_alert() instead of dev_err().
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 776c75010803849c1cc4f11031a2b3960ab05202 upstream.
I got a null-ptr-deref report:
KASAN: null-ptr-deref in range [0x0000000000000090-0x0000000000000097]
...
RIP: 0010:regulator_enable+0x84/0x260
...
Call Trace:
ahci_platform_enable_regulators+0xae/0x320
ahci_platform_enable_resources+0x1a/0x120
ahci_probe+0x4f/0x1b9
platform_probe+0x10b/0x280
...
entry_SYSCALL_64_after_hwframe+0x44/0xae
If devm_regulator_get() in ahci_platform_get_resources() fails,
hpriv->phy_regulator will point to NULL, when enabling or disabling it,
null-ptr-deref will occur.
ahci_probe()
ahci_platform_get_resources()
devm_regulator_get(, "phy") // failed, let phy_regulator = NULL
ahci_platform_enable_resources()
ahci_platform_enable_regulators()
regulator_enable(hpriv->phy_regulator) // null-ptr-deref
commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional()
misuse") replaces devm_regulator_get_optional() with devm_regulator_get(),
but PHY regulator omits to delete "hpriv->phy_regulator = NULL;" like AHCI.
Delete it like AHCI regulator to fix this bug.
Fixes: commit 962399bb7f ("ata: libahci_platform: Fix regulator_get_optional() misuse")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 013923477cb311293df9079332cf8b806ed0e6f2 upstream.
The last byte of "pad" is used without being initialized.
Fixes: 55dba3120f ("libata: update ->data_xfer hook for ATAPI")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a8526a5cd51cf5f070310c6c37dd7293334ac49 upstream.
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=201693
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210903094411.58749-1-hpa@redhat.com
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Krzysztof Olędzki <ole@ans.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ad4a31620355358316fa08fcfab37b9d6c33347 ]
Last change to device managed APIs cleaned up error path to simple phy_exit()
call, which in some cases has been executed with NULL parameter. This per se
is not a problem, but rather logical misconception: no need to free resource
when it's for sure has not been allocated yet. Fix the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210727125130.19977-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8a6430ab9c9c87cb64c512e505e8690bbaee190b upstream.
Commit ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6 ("libata: Enable queued TRIM for Samsung SSD 860")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475
Cc: stable@vger.kernel.org
Cc: Kate Hsuan <hpa@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 355a8031dc174450ccad2a61c513ad7222d87a97 ]
The loop on entry of ata_host_start() may not initialize host->ops to a
non NULL value. The test on the host_stop field of host->ops must then
be preceded by a check that host->ops is not NULL.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20210816014456.2191776-3-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecef6a9effe49e8e2635c839020b9833b71e934c ]
Data transfers are not required to be block aligned in memory, so they
span two pages. Fix this by splitting the call to >sff_data_xfer into
two for that case.
This has been broken since the initial libata import before the damn
of git, but was uncovered by the legacy ide driver removal.
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210709130237.3730959-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f6bca4d91b2ea052e917cca3f9d866b5cc1d500a upstream.
DIPM is unsupported or broken on sunxi. Trying to enable the power
management policy med_power_with_dipm on an Allwinner A20 SoC based board
leads to immediate I/O errors and the attached SATA disk disappears from
the /dev filesystem. A reset (power cycle) is required to make the SATA
controller or disk work again. The A10 and A20 SoC data sheets and manuals
don't mention DIPM at all [1], so it's fair to assume that it's simply not
supported. But even if it was, it should be considered broken and best be
disabled in the ahci_sunxi driver.
[1] https://github.com/allwinner-zh/documents/tree/master/
Fixes: c5754b5220 ("ARM: sunxi: Add support for Allwinner SUNXi SoCs sata to ahci_platform")
Cc: stable@vger.kernel.org
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Tested-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Link: https://lore.kernel.org/r/20210614072539.3307-1-public_timo.s@silentcreek.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5c8121262484d99bffb598f39a0df445cecd8efb ]
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Propagate the error code
upstream, as it should have been done from the start...
Fixes: 2fff275126 ("PATA host controller driver for ep93xx")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/509fda88-2e0d-2cc7-f411-695d7e94b136@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfc1f378c8953e68ccdbfe0a8c20748427488b80 ]
Iff platform_get_irq() fails (or returns IRQ0) and thus the polling mode
has to be used, ata_host_activate() hits the WARN_ON() due to 'irq_handler'
parameter being non-NULL if the polling mode is selected. Let's only set
the pointer to the driver's IRQ handler if platform_get_irq() returns a
valid IRQ # -- this should avoid the unnecessary WARN_ON()...
Fixes: 43f01da0f2 ("MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/3a241167-f84d-1d25-5b9b-be910afbe666@omp.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d3a62fbae8e5badc2342388f65ab2191c209cc0 ]
The driver overrides the error codes returned by platform_get_irq() to
-ENOENT, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/771ced55-3efb-21f5-f21c-b99920aae611@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a24efa16e7db02306fb5db84518bb0a7ada5a46 ]
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/105b456d-1199-f6e9-ceb7-ffc5ba551d1a@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b30d0040f06159de97ad9c0b1536f47250719d7d ]
Iff platform_get_irq() returns 0, ahci_platform_init_host() would return 0
early (as if the call was successful). Override IRQ0 with -EINVAL instead
as the 'libata' regards 0 as "no IRQ" (thus polling) anyway...
Fixes: c034640a32 ("ata: libahci: properly propagate return value of platform_get_irq()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/4448c8cc-331f-2915-0e17-38ea34e251c8@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6471a65fdd5efbb8dd2732dd0f063f960685ceb ]
The function mv_platform_probe() neglects to check the results of the
calls to platform_get_irq() and irq_of_parse_and_map() and blithely
passes them to ata_host_activate() -- while the latter only checks
for IRQ0 (treating it as a polling mode indicattion) and passes the
negative values to devm_request_irq() causing it to fail as it takes
unsigned values for the IRQ #...
Add to mv_platform_probe() the proper IRQ checks to pass the positive IRQ
#s to ata_host_activate(), propagate upstream the negative error codes,
and override the IRQ0 with -EINVAL (as we don't want the polling mode).
Fixes: f351b2d638 ("sata_mv: Support SoC controllers")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Link: https://lore.kernel.org/r/51436f00-27a1-e20b-c21b-0e817e0a7c86@omprussia.ru
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e379b40cc0f179403ce0b82b7e539f635a568da5 ]
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking
code to pass the positive IRQ #s to ata_host_activate(), propagate errors
upstream, and treat IRQ0 as error, returning -EINVAL, as the libata code
treats 0 as an indication that polling should be used anyway...
Fixes: 0df0d0a0ea ("[libata] ARM: add ixp4xx PATA driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7e8f404d56b99c80990b19a402c3f640d74be05 ]
The driver's probe() method is written as if platform_get_irq() returns 0
on error, while actually it returns a negative error code (with all the
other values considered valid IRQs). Rewrite the driver's IRQ checking code
to pass the positive IRQ #s to ata_host_activate(), propagate upstream
-EPROBE_DEFER, and set up the driver to polling mode on (negative) errors
and IRQ0 (libata treats IRQ #0 as a polling mode anyway)...
Fixes: a480167b23 ("pata_arasan_cf: Adding support for arasan compact flash host controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 234e6d2c18f5b080cde874483c4c361f3ae7cffe ]
On Hisilicon Kunpeng920, ESP is set to 1 by default for all ports of
SATA controller. In some scenarios, some ports are not external SATA ports,
and it cause disks connected to these ports to be identified as removable
disks. So disable the SXS capability on the software side to prevent users
from mistakenly considering non-removable disks as removable disks and
performing related operations.
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1615544676-61926-1-git-send-email-luojiaxing@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10340f8d7b6dd54e616339c8ccb2f397133ebea0 ]
While reworking the resources management and departing from using
ahci_platform_enable_resources() which did not allow a proper step
separation like we need, we unfortunately lost the ability to control
AHCI regulators. This broke some Broadcom STB systems that do expect
regulators to be turned on to link up with attached hard drives.
Fixes: c0cdf2ac4b5b ("ata: ahci_brcm: Fix AHCI resources management")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e4c309f9f33b76c09daa02b796ef87918eee494 ]
ata_qc_complete_multiple() has to be called with the tags physically
active, that is the hw tag is at bit 0. ap->qc_active has the same tag
at bit ATA_TAG_INTERNAL instead, so call ata_qc_get_active() to fix that
up. This is done in the vein of 8385d756e114 ("libata: Fix retrieving of
active qcs").
Fixes: 28361c4036 ("libata: add extra internal command")
Tested-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit df9c590986fdb6db9d5636d6cd93bc919c01b451 upstream.
Before commit 9495b7e92f716ab2 ("driver core: platform: Initialize
dma_parms for platform devices"), the R-Car SATA device didn't have DMA
parameters. Hence the DMA boundary mask supplied by its driver was
silently ignored, as __scsi_init_queue() doesn't check the return value
of dma_set_seg_boundary(), and the default value of 0xffffffff was used.
Now the device has gained DMA parameters, the driver-supplied value is
used, and the following warning is printed on Salvator-XS:
DMA-API: sata_rcar ee300000.sata: mapping sg segment across boundary [start=0x00000000ffffe000] [end=0x00000000ffffefff] [boundary=0x000000001ffffffe]
WARNING: CPU: 5 PID: 38 at kernel/dma/debug.c:1233 debug_dma_map_sg+0x298/0x300
(the range of start/end values depend on whether IOMMU support is
enabled or not)
The issue here is that SATA_RCAR_DMA_BOUNDARY doesn't have bit 0 set, so
any typical end value, which is odd, will trigger the check.
Fix this by increasing the DMA boundary value by 1.
This also fixes the following WRITE DMA EXT timeout issue:
# dd if=/dev/urandom of=/mnt/de1/file1-1024M bs=1M count=1024
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: failed command: WRITE DMA EXT
ata1.00: cmd 35/00:00:00:e6:0c/00:0a:00:00:00/e0 tag 0 dma 1310720 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
as seen by Shimoda-san since commit 429120f3df2dba2b ("block: fix
splitting segments on boundary masks").
Fixes: 8bfbeed586 ("sata_rcar: correct 'sata_rcar_sht'")
Fixes: 9495b7e92f716ab2 ("driver core: platform: Initialize dma_parms for platform devices")
Fixes: 429120f3df2dba2b ("block: fix splitting segments on boundary masks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45aefe3d2251e4e229d7662052739f96ad1d08d9 upstream.
Older ATF does not provide SMC call for SATA phy power on functionality and
therefore initialization of ahci_mvebu is failing when older version of ATF
is using. In this case phy_power_on() function returns -EOPNOTSUPP.
This patch adds a new hflag AHCI_HFLAG_IGN_NOTSUPP_POWER_ON which cause
that ahci_platform_enable_phys() would ignore -EOPNOTSUPP errors from
phy_power_on() call.
It fixes initialization of ahci_mvebu on Espressobin boards where is older
Marvell's Arm Trusted Firmware without SMC call for SATA phy power.
This is regression introduced in commit 8e18c8e58d ("arm64: dts: marvell:
armada-3720-espressobin: declare SATA PHY property") where SATA phy was
defined and therefore ahci_platform_enable_phys() on Espressobin started
failing.
Fixes: 8e18c8e58d ("arm64: dts: marvell: armada-3720-espressobin: declare SATA PHY property")
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Cc: <stable@vger.kernel.org> # 5.1+: ea17a0f153af: phy: marvell: comphy: Convert internal SMCC firmware return codes to errno
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95364f36701e62dd50eee91e1303187fd1a9f567 upstream.
In case a driver wants to return an error from qc_prep, return enum
ata_completion_errors. sata_mv is one of those drivers -- see the next
patch. Other drivers return the newly defined AC_ERR_OK.
[v2] use enum ata_completion_errors and AC_ERR_OK.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
