This adds an option to dump all crypto related memory to
the kernel log.
Obviously, it should not be enabled on productive systems. ;)
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should suspend the MAC, before we kill the radio. This gives
the MAC a chance to leave any TX/RX state and it avoids races on
the PHY/RADIO registers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packet length calculation (which includes frame check sequence)
should take into account whether we add a pad field or not.
Extract the calculation into a helper and use it in both places.
Changes to desc.c
Changes-licensed-under: ISC
Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some locking w.r.t. the lower MAC (firmware).
It also removes a lot of ancient IRQ-locking that's not needed anymore.
We simply suspend the MAC. That's easier and causes less trouble.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused parameter and unused local variable in
methods in iwl-tx.c:
- Remove a parameter (is_unicast) from iwl_tx_cmd_build_basic().
- Remove an unused variable name unicast from iwl_tx_skb().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX code in ath9k uses sc_keymap to figure out whether a default
key was used. However, the default key entries in sc_keymap were
always set and as such, frames could have been claimed to be decrypted
by hardware when they were not. This can cause problems especially
with TKIP since mac80211 is validating the Michael MIC in the frame
and this will result in MIC failure and potentially TKIP
countermeasures if the frame was not decrypted correctly.
Change key cache slot allocation to mark only the keys that really
have been used in sc_keymap to avoid the issue. The key cache slot
selection routines are now internally avoiding the slots that may be
needed for TKIP group keys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_reserve_key_cache_slot() was obviously supposed to return an index
to a free slot, not reserved one. This could have caused problems with
hardware revisions that use splitmic.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should fix the timeout issues seen when using wpa_supplicant.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a serious regression (introduced by:
"p54: fix memory management")
that affected isl3886+net2280 usb devices operation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Artur Skawina <art.08.09@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enhance allocation of key cache entries to support multiple pairwise
keys to fix AP mode with more than one associated STA.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like mac80211 may try to send unicast frames to a STA that
does not have a STA entry. We need to make sure that that is caught in
the rate control code before dereferencing STA data.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch checks if the radio is disabled before displaying the tx power
level. Previously when the txpower was set off show_tx_power still
returned the prior power level. Now it will indicate the power has been
turned off.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously we allocate Rx SKB with GFP_ATOMIC flag. This is because we need
to hold a spinlock to protect the two rx_used and rx_free lists operation
in the rxq.
spin_lock();
...
element = rxq->rx_used.next;
element->skb = alloc_skb(..., GFP_ATOMIC);
list_del(element);
list_add_tail(&element->list, &rxq->rx_free);
...
spin_unlock();
After spliting the rx_used delete and rx_free insert into two operations,
we don't require the skb allocation in an atomic context any more (the
function itself is scheduled in a workqueue).
spin_lock();
...
element = rxq->rx_used.next;
list_del(element);
...
spin_unlock();
...
element->skb = alloc_skb(..., GFP_KERNEL);
...
spin_lock()
...
list_add_tail(&element->list, &rxq->rx_free);
...
spin_unlock();
This patch should fix the "iwlagn: Can not allocate SKB buffers" warning
we see recently.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename vars in _iwl_poll_bit() to better reflect the truth.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes some useless goto in code cleanup.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables one to change the debug level at bit 31.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring up-to-date some comments on the location of debug files.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds line feed to printk.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes unused definition and moves code to proper places.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a parameter (dest) from iwl_fill_beacon_frame() (iwl-agn.c)
and from iwl3945_fill_beacon_frame(). (iwl-3945.c,iwl-3945.h)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes sure the rate control alg is registered/unregistered
only once for this module.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does pci_dma_sync_single_for_cpu() before accessing
the header of the frame and queueing the same buffer into h/w.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the possible MAC header pad before reporting TX status to
mac80211. This pad is hardware specific operation and should not be
exposed outside the driver. This fixes the frame body in monitor
interfaces that could be used to check on TX status for transmitted
frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The count field in struct ieee80211_tx_rate does not include the final
successful attempt, so only report retries here.
Fix the struct ieee80211_tx_rate::idx field when MCS was used. It is
supposed to be the MCS index, not an internal index to the rate
control algorithm table.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Hin-Tak Leung <htl10@users.sourceforge.net>
After the code was modified to use urb anchors ("rtl8187: Use usb anchor
facilities to manage urbs"), rtl8187 began generating an intermittent GPF
on shutdown when using SLUB with debugging enabled. Furthermore, rebooting
the system with a ping running caused a GPF every time. There are two problems:
(1) incorrect locking in the rtl8187_rx_cb() routine, a pre-existing bug that
apparently had not been triggered before, and (2) duplicate freeing of receive
skbs that was probably introduced with the change to anchors.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the tx code a bit and will be necessary for
the upcoming stlc45xx<->p54 port.
In detail: we no longer have to tell all back-end drivers directly,
if we want to free a frame right after it was send to the firmware,
or if we do it in the library callback later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces the static rssi auto calibration data
with more precise values out of the device's eeprom.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two places in the rtl8187 code where a routine was returning zero
(OK) when it should have been returning an error.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves a good chunk of code from the former statistic update
timer routine into a workqueue, which is kindly provided by mac80211.
Also as a nice side-effect we can lay the foundation for other
essential housekeeping features we want to do in the future.
e.g:
- drain the (clogged) tx_queue.
- initiate bursts.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate scaling in agn can be broken because of these two problems
1- the LQ command could not sent, we try to call LQ command before
post association will be rejected, this will cause the driver to
break in rs_tx_status reporting initial rate does not match.
2- In rs_rate_init we can get a value of 12, rate 60, for
last_txrate_idx, this rate only valid in SISO/MIMO mode only
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Padding the 802.11 header to a multiple of 4 bytes needs to be done only for
frames with a body. This fixes a bug where 2 bytes were missing in monitor
mode for ACK frames. Inspired by a patch from Jouni Malinen on ath9k.
Ref: http://bugzilla.kernel.org/show_bug.cgi?id=12101 :
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix and clean up the RX status reporting by getting rid of code that
used internal rate tables and ratekbps calculation. The correct value
is now reported with MCS index instead of the old mechanism that
defaulted to using the highest legacy rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that HT information is made available to the driver through
config() callback, the channel type can be calculated whenever
setting the channel. Update the rate table accordingly with the new
channel type.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
USB is going to switch the signature of the callbacks to
void callback(struct urb *urb, int status)
This patch will ease the transition.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could use DEFINE_IDR for statically allocated idr
that allow us to save a few lines of code.
And spell fix.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The accelerated iSCSI traffic could use a private IP address unknown to the OS:
- The IP address is required in both drivers to manage ARP requests and connection set up.
- Added an control call to retrieve the ip address.
- Reply to ARP requests dedicated to the private IP address.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code appears to be dead: nobody call these functions, plus build
breaks when UGETH_FILTERING is enabled:
ucc_geth.c:1848: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c:1848: warning: its scope is only this definition or declaration, which is probably not what you want
ucc_geth.c: In function 'ugeth_82xx_filtering_get_match_addr_in_hash':
ucc_geth.c:1856: error: dereferencing pointer to incomplete type
ucc_geth.c:1874: error: dereferencing pointer to incomplete type
ucc_geth.c:1877: warning: return from incompatible pointer type
ucc_geth.c: At top level:
ucc_geth.c:1885: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_hash':
ucc_geth.c:1894: error: dereferencing pointer to incomplete type
ucc_geth.c:1909: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1909: warning: assignment from incompatible pointer type
ucc_geth.c:1918: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:1928: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_clear_addr_in_hash':
ucc_geth.c:1947: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1947: warning: assignment from incompatible pointer type
ucc_geth.c:1954: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:2060: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_paddr':
ucc_geth.c:2064: error: dereferencing pointer to incomplete type
ucc_geth.c:2073: error: dereferencing pointer to incomplete type
ucc_geth.c:2075: warning: passing argument 2 of 'hw_add_addr_in_paddr' from incompatible pointer type
make[2]: *** [ucc_geth.o] Error 1
The code is there since the driver was merged, and nobody seem to be
interested in fixing or actually using it. If we ever want the
filtering support, we can always revert the patch and fix it, but so
far it just draws reader's attention.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't check ioremap() return value, and doesn't free the
remapped memory.
This patch fixes it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to call ucc_geth_memclean() so many times, just check for
errors in ucc_geth_open(), and call ucc_geth_stop() in case of errors.
The ucc_geth_stop() may be called anytime and will do the right thing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
open() routine calls stop() in case of errors, the function will try
to free the requested IRQ. But we don't know if it was actually
requested, so the code might issue bogus free_irq(0, dev) call.
Fix this by rearranging the code so that now request_irq() is the last
call in the open() routine, and move free_irq() into the close().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeout handling code is currently broken in several ways:
- It calls stop() (which frees all the memory and IRQ), and then
calls startup() (which won't re-request IRQ, neither it will
re-init the Fast UCC structure).
- It calls these routines from the softirq context, which is wrong,
since stop() calls free_irq() (which might sleep) and startup()
allocates things with GFP_KERNEL.
- It won't soft-reset the PHY. We need the PHY reset for at least
MPC8360E-MDS boards with Marvell 88E1111 PHY, the PHY won't recover
from timeouts w/o the reset.
So the patch fixes these problems by implementing the workqueue for the
timeout handling, and there we fully re-open the device via close() and
open() calls. The close/open paths do the right things, and I can see
that the driver actually survive the timeouts.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the routines wait for the various bits w/o an assumption that
bits may never get set. When timeouts happen I see that these bits never
get set and so the routines hang the kernel.
With this patch we'll wait the graceful stop for 100 ms, and then will
simply exit. There is nothing* we can do about that, but it's OK since
we'll do full reset later.
* Well, actually, there is also not-graceful variant for the TX stop,
but specs says that we never should use it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize the lightly loaded case, by only synchronizing discards stats
when qlen > 10 indicate potential for drops.
Notice Robert Olsson might disagree with this patch.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard packet counter debug statements that can be turned on
at runtime by users to assist debugging of the driver code.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementing discard counters for the NIU driver turned out to be more
complicated than first assumed.
The discard counters for the NIU neptune chip are only 16-bit (even
though this is a 64-bit chip). These 16-bit counters can overflow
quickly, especially considering this is a 10Gbit/s ethernet card.
The overflow indication bit is, unfortunatly, not usable as the
counter value does not wrap, but remains at max value 0xFFFF.
Resulting in lost counts until the counter is reset.
The read and reset scheme also poses a problem. Both in theory and in
practice counters can be lost in between reading nr64() and clearing
the counter nw64(). For this reason, the number of counter clearings
nw64() is limited/reduced. On the fast-path the counters are only
syncronized once it exceeds 0x7FFF. When read by userspace, its
syncronized fully.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
A major source of overhead in the enc28j60 driver is the SPI transfers. Each
SPI transfer entails two kernel thread context switches. One major source of
SPI transfers is the enc28j60_set_bank() functions which runs before every
register access. This patch reduces the number of SPI transfers that
enc28j60_set_bank() performs in two ways:
1. removes unnecessary bank switch for the registers that are present in all
banks
2. when switching from banks 0 or 3 to banks 1 or 2 (i.e. only one bit
changes) enc28j60_set_bank() does only one SPI transfer instead of two
According to my tests these changes reduce the number of SPI transfers in
about 25%.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
| commit 3d29b0c33d
| Author: John W. Linville <linville@tuxdriver.com>
| Date: Fri Oct 31 14:13:12 2008 -0400
|
| netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
|
| We have some reasons to kill netdev->priv:
| 1. netdev->priv is equal to netdev_priv().
| 2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
| netdev_priv() is more flexible than netdev->priv.
| But we cann't kill netdev->priv, because so many drivers reference to it
| directly.
|
| OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
| and I want to kill netdev->priv later, I decided to convert all the direct
| reference of netdev->priv first.
|
| (Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
| changelog but using dev->ml_priv. That doesn't seem appropriate
| to me for this driver, so I've revamped it to use netdev_priv()
| instead. -- JWL)
This commit changed the allocation of netdev, but didn't change
the free method of it.
This causes "zd" be used after the memory, which is pointed by "zd", being
freed by free_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a segfault in ppp_shutdown_interface() and
ppp_destroy_interface() when a PPP connection is closed. I bisected
the problem to the following commit:
commit c8019bf3af
Author: Wang Chen <wangchen@cn.fujitsu.com>
Date: Thu Nov 20 04:24:17 2008 -0800
netdevice ppp: Convert directly reference of netdev->priv
1. Use netdev_priv(dev) to replace dev->priv.
2. Alloc netdev's private data by alloc_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original ppp_generic code treated the netdev and struct ppp as
independent data structures which were freed separately. In moving the
ppp struct into the netdev, it is now possible for the private data to
be freed before the call to ppp_shutdown_interface(), which is bad.
The kfree(ppp) in ppp_destroy_interface() is also wrong; presumably
ppp hasn't worked since the above commit.
The following patch fixes both problems.
Signed-off-by: James Chapman <jchapman@katalix.com>
Reviewed-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I also removed some of the unneeded braces in the if condition to
improve readability and a little bit of reformatting.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all defined before used, it's therefore ok to remove
them.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the pointless comment at the top.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It helps in maintaining the various partner information values from
the LACPDU. It also removes the pointless comment at the top.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It generally helps to handle those values in various places, using it
might make the code more readable and gives room for other improvements.
The IEEE standard talks about them as "parameter values".
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code was just a funny way of assigning both values (they
are both of type u8).
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA memory for the jumbo rx page rings was freed incorrectly using the
wrong local variable as the array index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_poll would declare polling done once the rx queue was empty,
but the tx queue could still have packets left.
Stolen mostly from the e1000 driver.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No clean up function is executed in the interrupt context by this patch.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface name (ex. eth0) is used as the prefix for the interrupt name,
with _rx, _tx, and _er appended to distinguish multiple interrupts on
the same interface.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scatter Gather support in gianfar driver to handle fragmented frames on
the transmit side.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch which fixed gianfar so it drops packets when it runs out
of memory left in the code which frees the skb when it drops packets.
Change the code so that we only free the skb if the new skb was successfully
created.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use idr technique instead of own implemented cardmaps.
It saves us a number of lines and gives an ability
to use library functions.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel BUG at drivers/net/phy/mdio_bus.c:165!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
How?
mdiobus_alloc() sets bus->state = MDIOBUS_ALLOCATED.
mdiobus_register() sets bus->state = MDIOBUS_REGISTERED but then can
fail (mdiobus_scan()) returning an error to the caller.
The caller aborts correctly with mdiobus_free() which does:
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are now defined in linux/mii.h and the bnx2x driver
defines different values which are shared with hardware
data structures.
So add a "BNX2X_" prefix to these macro names.
Based upon a report from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix the 5716S pci_device_id entry to point to the proper string.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change MSI-X vector names to "ethx-%d".
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
starfire napi ->poll() handler can return work == weight after calling
netif_rx_complete() (if there is no more work). It is illegal and this
patch fixes it.
Reported-by: Alexander Huemer <alexander.huemer@sbg.ac.at>
Tested-by: Alexander Huemer <alexander.huemer@sbg.ac.at>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset. With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever we want to update the status field in a BD, we usually want to
update the length field, too. By combining them into one 32-bit field, we
reduce the number of stores to memory shared with the controller, and we
eliminate the need for order-enforcement, as the length and "READY" bit are
now updated atomically at the same time.
Signed-off-by: Dai Haruki <Dai.Haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is based strongly on code from Dai Haruki <Dai.Haruki@freescale.com>.
The gianfar Buffer Descriptors are arranged in a circular array, the end of
which is denoted by setting the "WRAP" bit in the descriptor. However, the
software knows the end of the ring because it knows how many descriptors are
there. Rather than check each descriptor for whether the WRAP bit is set,
use pointer math to determine where the next BD is. This is also useful for
when we want to look at BDs other than the very next one (for Scatter-Gather).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Also, use cacheable_memzero instead of memset for performance reasons.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eTSEC can prepend up to 32 bytes to a received frame, usually for the
purpose of aligning the IP address to a word boundary, so this turns it on.
While we're in there, make the handling of the pre-frame bytes (padding and
Frame Control Block) cleaner.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize the VLAN checking logic as well.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some bugs in the ethtool configuration functions:
* gfar_clean_rx_ring should not be called with interrupts disabled.
* Update last transmission time to avoid tx timeout.
* Delete redundant NETIF_F_IP_CSUM check in gfar_start_xmit
* Use netif_tx_lock_bh when reconfiguring the tx csum
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the interrupt coalescing values in the form in which they will be
written to the interrupt coalescing registers. This puts a little overhead
into the ethtool configuration, and takes it out of the interrupt handler
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_halt does everything we want to do there, including disabling
TX/RX. It also doesn't unnecessarily enable DMA if it's already
stopped.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The big rx/tx buffer support is broken and unlikely to be very useful
as such. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix pci unmapping problem introduced by commit id
8953f12827 "tlan: Fix small (< 64 bytes)
datagram transmissions".
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.
The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC driver can work with mutliple versions of the FW.
Let the driver load when the embedded FW does not match,
and the FW update mechanism failed.
The iWARP module will make its own loading decision.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enc28j60 driver reads incoming packets in the process (workqueue) context,
not in a tasklet or the interrupt context. Thus, we should use netif_rx_ni()
to deliver those packets to the networking layer, instead of netif_rx(). This
way incoming packets don't wait in the incoming queue for the next IRQ to be
serviced.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TLAN chip does not support tranmissions smaller than 64
bytes. Smaller transfers need to be padded up to that size. This was
broken by commit id 41873e9aff ("tlan:
get rid of padding buffer").
<URL:http://bugzilla.kernel.org/show_bug.cgi?id=11754>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pppol2tp driver has had broken UDP checksum code for a long
time. This patch fixes it. If UDP checksums are enabled in the
tunnel's UDP socket, the L2TP driver now properly validates the
checksum on receive and fills in the checksum on transmit. If the
network device has hardware checksum support and is enabled, it is
used instead of generating/checking the checksum in software.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement NIC Tx multiqueue.
Bump up driver version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support to e1000e by making it invoke napi_gro_receive
instead of netif_receive_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
