Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:
* The source is calculated as 512 + the value written into the MSI
register
* The vector for this source is added to the source and reported
through IACK
This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.
Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.
If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.
Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC " to "PASEMI-OPIC".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we hardwire the number of SLBs to 64, but PAPR says we
should use the ibm,slb-size property to obtain the number of SLB
entries. This uses this property instead of assuming 64. If no
property is found, we assume 64 entries as before.
This soft patches the SLB handler, so it shouldn't change performance
at all.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert #include of asm/of_{platform, device}.h into
linux/of_{platform,device}.h for a few scattered platforms.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix up the module information for gpio-mdio, it wouldn't load
because of lacking license, and wouldn't auto-load because of missing
MODULE_DEVICE_TABLE.
Signed-off-by: Olof Johansson <olof@lixom.net>
Use smp_send_stop() to move all cpus besides the one executing reboot
into a hold loop, to keep them from being in powersavings mode at the
time of reboot.
Signed-off-by: Olof Johansson <olof@lixom.net>
When the PWRficient cpus are entered into powersavings states, the
astate is automatically dropped down to 0. While we still restore it
when we come out of idle, it can still cause some weird effects with
respect to performance (especially since it takes a while to ramp up to
higher astates).
So, to avoid this, don't enter power savings when the cpufreq driver
(or user) has set higher astates than 0.
The restore is still required, since there's a chance the astate has
been raised from the other cpu while the idling one was asleep.
Signed-off-by: Olof Johansson <olof@lixom.net>
There will be more product numbers in the future than just PA6T-1682M,
but they will share much of the features. Remove some of the explicit
references and compatibility checks with 1682M, and replace most of them
with the more generic term "PWRficient".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Doug Thompson <dougthompson@xmission.com>
Misc cleanups of mdio_gpio:
* Better error handling/unrolling in case of init/alloc failures
* Go through child nodes and get their interrupts instead of using
hardcoded values
* Remap the GPIO registers at module load/driver init instead of during probe
* Coding style and other misc cleanups
Signed-off-by: Olof Johansson <olof@lixom.net>
Due to an erratum, we don't want to reset the mpic at boot time. It can
sometimes cause problems with lost interrupts later on while running.
Signed-off-by: Olof Johansson <olof@lixom.net>
Driver for the CompactFlash slot on the PA Semi Electra eval board. It's
a simple device sitting on localbus, with interrupts and detect/voltage
control over GPIO.
The driver is implemented as an of_platform driver, and adds localbus
as a bus being probed by the of_platform framework.
[akpm@linux-foundation.org: cleanups]
[olof@lixom.net: fix build]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
We no longer initialise the name and owner fields of the
of_platform_driver, but use the fields of the embedded device_driver's
name field instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pasemi_mac: enable iommu support
Enable IOMMU support for pasemi_mac, but avoid using it on non-partitioned
systems for performance reasons.
The user can override this by selecting the PPC_PASEMI_IOMMU_DMA_FORCE
configuration option.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Some versions of PWRficient 1682M have an interrupt controller in which
the first register in each pair for interrupt sources doesn't always
read with the right polarity/sense values.
To work around this, keep a software copy of the register instead. Since
it's not modified from the mpic itself, it's a feasible solution. Still,
keep it under a config option to avoid wasting memory on other platforms.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move pasemi_idle_init() to be a late_initcall instead of being called from
setup_arch(). This way the cpufreq driver has a chance to initialize and
save away the boot time astate before we go to idle for the first time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add printout of some SoC error status registers, and dump the SLB contents
for those machine check events where it makes sense.
Since we can't go about and ioremap registers at machine check time,
and we generally want to do as little as possible to print out the
information, pre-build a table of the registers to dump and their address
in the common PCI config space range.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Erratum 5945 causes some of the registers on the PCIe root ports to
not read correctly. Do a small dance to avoid this: Write an unused
register, read the value and write it back. Thankfully this is not in
a hot code path.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add pasemi_pci_getcfgaddr(), to get the remapped address of a specific
config register for a PCI device.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
More fallout from the switch from PAGE_SIZE based IOMMU to the native page
size for the driver. By pure luck it happened to work most of the time, since
we end up invalidating the wrong entries in the TLB.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework timebase handoff to play nice with configurations with more than
2 cores, as well as with CPU hotplug.
Previous scheme just pushed out the current timebase from the giving
core to all cores without caring if they wanted it or not, nor checking
if they'd taken it. The taking side didn't make sure the giving side
had provided a value yet either. In other words, it was completely broken.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These functions are only called by __init functions.
WARNING: vmlinux.o(.text+0x56aa0): Section mismatch: reference to .init.text:.lmb_alloc (between '.iob_init' and '.iommu_init_early_pasemi')
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pasemi pci configuration space write method reads the written
location immediately after the write is performed, presumably in order
to flush the write. However, configuration space writes are not
allowed to be posted, making these reads gratuitous. Furthermore,
this behavior potentially causes us to violate the PCI PM spec when
changing between e.g. D0 and D3 states, because a delay of up to 10ms
may be required before the OS accesses configuration space after the
write which initiates the transition.
Remove the unnecessary reads from pa_pxp_write_config.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Disable auto-select of CONFIG_EMBEDDED. ELECTRA_IDE selects
PATA_PLATFORM which should be sufficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename the pasemi platform to "pasemi" to be in line with the
platform's directory name.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Glue code to hook up the pata_platform on the PA Semi Electra eval board.
CFE sets up device tree entries for the IDE interface, with device type
'ide' and compatible field 'electra-ide'.
We unfortunately need to modify the resources before calling the generic
platform driver, since the device tree only has one register window in
it and the driver expects two. Adding this as an of_platform driver
instead doesn't give us any benefit, it just adds one more layer of
register/probe functions.
Since CONFIG_PATA_PLATFORM depends on CONFIG_EMBEDDED, add that as a
default for PPC_PASEMI.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64. The main goals are:
- Get rid of imalloc and use more common code where possible
- Simplify the current mess so that PIO space is allocated and
mapped in a single place for PCI bridges
- Handle allocation constraints of PIO for all bridges including
hot plugged ones within the 2GB space reserved for IO ports,
so that devices on hotplugged busses will now work with drivers
that assume IO ports fit in an int.
- Cleanup and separate tracking of the ISA space in the reserved
low 64K of IO space. No ISA -> Nothing mapped there.
I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)
With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.
This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)
A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).
imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.
I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.
This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc iommu code was refactored by Linas back in the 2.6.20 time
frame to map 4K pages from the generic code, but I had forgotten to go
back and fix my platform driver before submitting it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
and so needs to include asm/smp.h so a UP build works.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current kernel implements proper TB sync, no need to keep GENERIC_TBSYNC
enabled.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
fixes:
arch/powerpc/platforms/pasemi/idle.c: In function 'pasemi_system_reset_exception':
arch/powerpc/platforms/pasemi/idle.c:55: warning: implicit declaration of function 'do_IRQ'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
[netdrvr] atl1: fix build
pasemi_mac: Use local-mac-address instead of mac-address if available
pasemi_mac: PHY support
pasemi_mac: Add msglevel support and "debug" module param
pasemi_mac: Logic cleanup / rx performance improvements
pasemi_mac: Minor cleanup / define fixes
pasemi_mac: Add SKB reuse / copy-break
pasemi_mac: Timer and interrupt fixes
pasemi_mac: Abstract and fix up interrupt restart routines
pasemi_mac: Move the IRQ mapping from the PCI layer to the driver
tc35815: Remove unnecessary skb->dev assignment
drivers/net/dm9000: Convert to generic boolean
AT91RM9200 Ethernet: Fix multicast addressing
AT91RM9200 Ethernet: Support additional PHYs
PCMCIA-NETDEV : xirc2ps_cs: bugfix of multicast code
sky2: re-enable 88E8056 for most motherboards
MIPS: Drop unnecessary CONFIG_ISA from RBTX49XX
ne: MIPS: Use platform_driver for ne on RBTX49XX
ne: Add NEEDS_PORTLIST to control ISA auto-probe
ne: Misc fixes for platform driver.
...
Fix conflict in drivers/net/pasemi_mac.c (get_property() got renamed to
of_get_property()) manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes for ethernet IRQ mapping, to be done in the driver instead of in
the platform setup code.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the global cpu speed variable according to current cpufreq speed,
/proc/cpuinfo reports the actual speed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for consistency with other Open Firmware interfaces (and Sparc).
This is just a straight replacement.
This leaves the compatibility define in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only publish of_platform devices if running on a machine that has them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just another pass through arch/powerpc for old usages.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cpufreq driver for PA Semi PWRficient processors.
Signed-off-by: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/gpio_mdio.c really depends on CONFIG_PHYLIB.
Add a config option for it, allow for it to be disabled if needed and fix
the dependency.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/pasemi/setup.c: In function 'pasemi_publish_devices':
arch/powerpc/platforms/pasemi/setup.c:220: warning: implicit declaration of function 'of_platform_bus_probe'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MDIO driver for PHY's connected via GPIO as on the PA Semi Electra
eval board.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reset MPIC on boot to clear some timer state that firmware might
leave configured.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device 0 function 0 on the root bus is really a two-function bus agent,
but only the first function is visible. Because of this, we need to
allow config accesses into the second range. Modify the check for valid
offsets accordingly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
