Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.
This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
X touchscreen drivers that don't interpret the designated pen up message
assume a pen up event from a pressure value 0. For these we generate a
pressure 0 message along with the pen up message.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pen down IRQ will toggle during each X,Y,Z measurement cycle.
Even though the IRQ is disabled it will be latched and delivered
when after enable_irq. Thus in the IRQ handler we must avoid
starting a new measurement cycle when such an "unwanted" IRQ happens.
Add a get_pendown_state platform function, which will probably
determine this by reading the current GPIO level of the pen IRQ pin.
Move the IRQ reenabling from the SPI RX function to the timer. After
the last power down message the pen IRQ pin is still active for a
while and get_pendown_state would report incorrectly a pen down state.
When suspending we should check the ts->pending flag instead of
ts->pendown, since the timer can be pending regardless of ts->pendown.
Also if ts->pending is set we can be sure that the timer is running,
so no need to rearm it. Similarly if ts->pending is not set we can
be sure that the IRQ is enabled (and the timer is not).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Add disable attribute to support device locking mode where
unintentional touch event shouldn't wake up the system;
- Update comments;
- Add missing spin_lock_init;
- Do device resume with the lock held;
- Do cleanup calls / free memory in the reverse order of initialization.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes a polling loop had a hard time changing state without
pre-emption enabled. Use msleep instead, it's better anyway.
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchscreens seem to oscillate heavily for a while after touching
the screen. Implement support for sampling the screen until we get two
consecutive values that are close enough.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Submit a seperate request for powering down the ADC in ads7846,
doing it after the last read request. Otherwise some of the read
values are incorrect.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It's handy for userspace diagnostics to see the pen down status, to
see whether the touchscreen is "stuck" (shortcircuited).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Toshiba Protege M300 also requires the same workaround as Satellites
and Dynabooks - Synaptics report rate should be lowered to 40pps
(from 80), otherwise KBC starts losing keypresses.
Signed-off-by: Richard Thrippleton <ret28@cam.ac.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SNES gamepads and mice share the same type of interface so they both can be
connected to the parallel port using a simple interface. Adding mouse
support to a gamepad driver may sound funny at first, but doing so in this
case makes it possible to connect and SNES gamepads and mice at the same
time, on the same port.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs can't handle more than PAGE_SIZE data coming from attributes'
show() methods; make sure we respect this limit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On Thu, Mar 30, 2006 at 08:31:02AM -0500, Dmitry Torokhov wrote:
> Don't do that, its double free. input_unregister_device() normally
> causes release() to be called and free the device. input_free_device
> is only to be called when input_register_device has not been called or
> failed.
>
> Plus you might want to unregister device after closing serio port,
> otherwise your interrupt routine might be referencing already freed
> memory.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Addresses in F-space must be accessed uncached on most parisc machines.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
drivers/char/ftape/lowlevel/fdc-io.c: Correct a comment
Kconfig help: MTD_JEDECPROBE already supports Intel
Remove ugly debugging stuff
do_mounts.c: Minor ROOT_DEV comment cleanup
BUG_ON() Conversion in drivers/s390/block/dasd_devmap.c
BUG_ON() Conversion in mm/mempool.c
BUG_ON() Conversion in mm/memory.c
BUG_ON() Conversion in kernel/fork.c
BUG_ON() Conversion in ipc/sem.c
BUG_ON() Conversion in fs/ext2/
BUG_ON() Conversion in fs/hfs/
BUG_ON() Conversion in fs/dcache.c
BUG_ON() Conversion in fs/buffer.c
BUG_ON() Conversion in input/serio/hp_sdc_mlc.c
BUG_ON() Conversion in md/dm-table.c
BUG_ON() Conversion in md/dm-path-selector.c
BUG_ON() Conversion in drivers/isdn
BUG_ON() Conversion in drivers/char
BUG_ON() Conversion in drivers/mtd/
drivers/input/touchscreen/ads7846.c: In function `ads7846_read12_ser':
drivers/input/touchscreen/ads7846.c:207: warning: implicit declaration of function `disable_irq'
drivers/input/touchscreen/ads7846.c:209: warning: implicit declaration of function `enable_irq'
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (21 commits)
BUG_ON() Conversion in drivers/video/
BUG_ON() Conversion in drivers/parisc/
BUG_ON() Conversion in drivers/block/
BUG_ON() Conversion in sound/sparc/cs4231.c
BUG_ON() Conversion in drivers/s390/block/dasd.c
BUG_ON() Conversion in lib/swiotlb.c
BUG_ON() Conversion in kernel/cpu.c
BUG_ON() Conversion in ipc/msg.c
BUG_ON() Conversion in block/elevator.c
BUG_ON() Conversion in fs/coda/
BUG_ON() Conversion in fs/binfmt_elf_fdpic.c
BUG_ON() Conversion in input/serio/hil_mlc.c
BUG_ON() Conversion in md/dm-hw-handler.c
BUG_ON() Conversion in md/bitmap.c
The comment describing how MS_ASYNC works in msync.c is confusing
rcu: undeclared variable used in documentation
fix typos "wich" -> "which"
typo patch for fs/ufs/super.c
Fix simple typos
tabify drivers/char/Makefile
...
sparc32:
drivers/input/touchscreen/ads7846.c: In function `ads7846_read12_ser':
drivers/input/touchscreen/ads7846.c:206: warning: implicit declaration of function `disable_irq'
drivers/input/touchscreen/ads7846.c:208: warning: implicit declaration of function `enable_irq'
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* Change the scan interval from 100ms to 50ms. This stops the key
repeat from triggering on double letter presses.
* Remove unneeded stale hinge code from corgikbd
* Change unneeded corgi GPIO pins to inputs when suspended
* Add support for the headphone jack switch for both corgi and spitz
(as switch SW_2)
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not assume that pnp_register_driver() returns the number of
devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not assume that pnp_register_driver() returns the number of
devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The current pcspkr code combines the device and driver registration.
This patch splits these, putting the device registration in the arch
specific code.
PowerPC and MIPS only have the pcspkr present sometimes.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow disabling atkbd driver if CONFIG_EMBEDDED is enabled. Previously
it was impossible to disable atkbd on X86_PC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not activate softrepeat by default on dumb keyboards as it clashes
with their own hardware repeat (for example Dell DRAC3). Softrepeat
can still be activated manually via module parameter or sysfs.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix bat_xl and err_xl logic causing atkbd to complain about 'unknown
key 0x7f'. Noted by Ben LaHaise.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Automatic resynchronization in psmouse driver causes problems on some
hardware so disable it by default for now. People with KVM switches
that require resync can still enable it via module parameter or sysfs
attribute.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Serio and gameport cores do not depend on other drivers and are
used by code living outside of drivers/input/{gameport|serio}.
Registering them at subsystem level guarantees that they are
fully initialized before anyone tries to use them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Amijoy conversion was done by Arjan van de Ven.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
98kbd{,-io} and 98spkr all went out with PC98 subarch. Remove stale Makefile
entries that remained.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This updates the ads7846 touchscreen driver:
- to allow faster clocking (this driver doesn't push sample rates);
- bugfixes the conversion of spi_transfer to lists;
- some dma-unsafe command buffers are fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Logitech mouse type 99 (Premium Optical Wheel Mouse, model M-BT58,
plain 3 buttons + wheel) to cure the following message: logips2pp: Detected
unknown logitech mouse model 99
Signed-off-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion to wait_event_interruptible_timeout() caused
USB detection routine erroneously report timeouts for perfectly
working devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently, "while true; do cat </dev/null >/dev/input/mice; done" causes
an OOM in a short amount of time. Funny that nobody noticed, it actually
is very easy to trigger just by switching between VT1 and VT7...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for beeper found in LinkSys NSLU2 boxes. It should work
on any ixp4xx based platform.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There's no need to have request_irq followed by set_irq_type.
Just use request_irq with the appropriate SA_TRIGGER flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of the reasons for keeping these separate before was due to hp690
discontig, and since we have a workaround for that now (abusing some shadow
space so everything is magically contiguous), there's no reason to keep the
targets separate.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.
From: David Brownell <dbrownell@users.sourceforge.net>
Updates including doc, bugfixes to the list code, add
spi_message_add_tail(). Plus, initialize things _before_ grabbing the
locks in some cases (in case it grows more expensive). This also merges
some bitbang updates of mine that didn't yet make it into the mm tree.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the ads7864 driver to use the new "spi_driver" struct, and
includes some minor unrelated cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers. Key differences from those two:
- Uses the new SPI framework (minimalist version)
- <linux/spi/ads7846.h> abstracts board-specific touchscreen info
- Sysfs attributes for the temperature and voltage sensors
- Uses fewer ARM-specific IRQ primitives
The temperature and voltage sensors show up in sysfs like this:
$ pwd
/sys/devices/platform/omap-uwire/spi2.0
$ ls
bus@ input:event0@ power/ temp1 vbatt
driver@ modalias temp0 vaux
$ cat modalias
ads7846
$ cat temp0
991
$ cat temp1
1177
$
So far only basic testing has been done. There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.
One portability note may be of special interest. It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response". Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention. So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The API and code have been through various bits of initial review by
serial driver people but they definitely need to live somewhere for a
while so the unconverted drivers can get knocked into shape, existing
drivers that have been updated can be better tuned and bugs whacked out.
This replaces the tty flip buffers with kmalloc objects in rings. In the
normal situation for an IRQ driven serial port at typical speeds the
behaviour is pretty much the same, two buffers end up allocated and the
kernel cycles between them as before.
When there are delays or at high speed we now behave far better as the
buffer pool can grow a bit rather than lose characters. This also means
that we can operate at higher speeds reliably.
For drivers that receive characters in blocks (DMA based, USB and
especially virtualisation) the layer allows a lot of driver specific
code that works around the tty layer with private secondary queues to be
removed. The IBM folks need this sort of layer, the smart serial port
people do, the virtualisers do (because a virtualised tty typically
operates at infinite speed rather than emulating 9600 baud).
Finally many drivers had invalid and unsafe attempts to avoid buffer
overflows by directly invoking tty methods extracted out of the innards
of work queue structs. These are no longer needed and all go away. That
fixes various random hangs with serial ports on overflow.
The other change in here is to optimise the receive_room path that is
used by some callers. It turns out that only one ldisc uses receive room
except asa constant and it updates it far far less than the value is
read. We thus make it a variable not a function call.
I expect the code to contain bugs due to the size alone but I'll be
watching and squashing them and feeding out new patches as it goes.
Because the buffers now dynamically expand you should only run out of
buffering when the kernel runs out of memory for real. That means a lot of
the horrible hacks high performance drivers used to do just aren't needed any
more.
Description:
tty_insert_flip_char is an old API and continues to work as before, as does
tty_flip_buffer_push() [this is why many drivers dont need modification]. It
does now also return the number of chars inserted
There are also
tty_buffer_request_room(tty, len)
which asks for a buffer block of the length requested and returns the space
found. This improves efficiency with hardware that knows how much to
transfer.
and tty_insert_flip_string_flags(tty, str, flags, len)
to insert a string of characters and flags
For a smart interface the usual code is
len = tty_request_buffer_room(tty, amount_hardware_says);
tty_insert_flip_string(tty, buffer_from_card, len);
More description!
At the moment tty buffers are attached directly to the tty. This is causing a
lot of the problems related to tty layer locking, also problems at high speed
and also with bursty data (such as occurs in virtualised environments)
I'm working on ripping out the flip buffers and replacing them with a pool of
dynamically allocated buffers. This allows both for old style "byte I/O"
devices and also helps virtualisation and smart devices where large blocks of
data suddenely materialise and need storing.
So far so good. Lots of drivers reference tty->flip.*. Several of them also
call directly and unsafely into function pointers it provides. This will all
break. Most drivers can use tty_insert_flip_char which can be kept as an API
but others need more.
At the moment I've added the following interfaces, if people think more will
be needed now is a good time to say
int tty_buffer_request_room(tty, size)
Try and ensure at least size bytes are available, returns actual room (may be
zero). At the moment it just uses the flipbuf space but that will change.
Repeated calls without characters being added are not cumulative. (ie if you
call it with 1, 1, 1, and then 4 you'll have four characters of space. The
other functions will also try and grow buffers in future but this will be a
more efficient way when you know block sizes.
int tty_insert_flip_char(tty, ch, flag)
As before insert a character if there is room. Now returns 1 for success, 0
for failure.
int tty_insert_flip_string(tty, str, len)
Insert a block of non error characters. Returns the number inserted.
int tty_prepare_flip_string(tty, strptr, len)
Adjust the buffer to allow len characters to be added. Returns a buffer
pointer in strptr and the length available. This allows for hardware that
needs to use functions like insl or mencpy_fromio.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These haven't worked in some time, and we've dropped support for the bus
from the SH tree until someone shows some interest in maintaining it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Avoid doing assignments to a live ->fops so it can be marked as 'const'.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
offset can never be < 0 because it has type size_t. The driver
currently oopses on insmod if BIOS does not support the interface,
instead of refusing to load.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Many ARM drivers do not need to include asm/irq.h - remove this
unnecessary include from some ARM drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call serio_reconnect() instead of serio_rescan() when detecting that
a new keyboard was plugged in. This should help KVM uses losing custom
keymap settings when switching between boxes.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Here's the patch for modalias support for input classes. It uses
comma-separated numbers, and doesn't describe all the potential keys (no
module currently cares, and that would make the strings huge). The
changes to input.h are to move the definitions needed by file2alias
outside __KERNEL__. I chose not to move those definitions to
mod_devicetable.h, because there are so many that it might break compile
of something else in the kernel.
The rest is fairly straightforward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
CC: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It makes zero sense to have hotplug, but not the netlink
events enabled today. Remove this option and merge the
kobject_uevent.h header into the kobject.h header file.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a typo introduced by conversion to dynamic input_dev
allocation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Christophe Zimmerman, this explains the slow mouse movement
with 2.6.x kernels.
And checking the 2.4.x drivers/sbus/char/sunmouse.c driver shows we
always used a 5-byte protocol with Sun mice in the past. I have no
idea how the 3-byte thing got into the 2.6.x driver, but it's surely
wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding would work.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not use platform_device_register_simple() as it is going away,
implement ->probe() and ->remove() functions so manual binding and
unbinding will work with this driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This DMI data was found in Fujitsu LifeBook B142 (Product S/N
FPC01003B, italian keyboard); re: bugzilla #5335
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It looks like quite a few mice out there treat PSMOUSE_RESET_DIS
as a powerdown request and turn off the light rendering the mouse
unusable.
Vojtech recommended to switch from PSMOUSE_RESET_DIS to full reset,
however we don't want to do that everywhere as full reset is pretty
slow. Instead we only use it before probing for "generic" protocols,
such as IntelliMouse and Explorer, to make sure that the mouse will
be woken up if it went to sleep as a result of PSMOUSE_RESET_DIS
issued earlier.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this patch Forward and Backward buttons on the touchpad do not
generate any events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Compat and normal code mirror each other and are hard to maintain.
When EV_SW was added compat_ioctl case was missed. Here is my attempt
at consolidating the code.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
kseriod and kgameportd used to process all pending events before
checking for freeze condition. This may cause swsusp to time out
while stopping tasks when resuming. Switch to process events one
by one to check freeze status more often.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If thread that submitted FF request gets interrupted somehow it
will release request structure and ioctl handler will work with
freed memory. TO prevent that from happening switch to using
wait_for_completion instead of wait_for_completion_interruptible.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Try to save battery power by disabling wifi and bluetooth on suspend.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also fix a potential issue with some notebooks:
The current code assumes the response to bios_wifi_get_default_setting is
either 1 (disabled) or 3 (enabled), or wifi isn't supported. The BIOS
response appears to be a bit field w/ 0x1 indicating hardware presence, 0x2
indicating actiation status, and the other 6 bits being unknown/reserved --
with the patch, these 6 bits are ignored.
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On x86_64:
{standard input}:233: Error: suffix or operands invalid for `push'
{standard input}:233: Error: suffix or operands invalid for `pop'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A driver for laptop buttons using an x86 BIOS interface that is
apparently used on quite a few laptops and seems to be originating
from Wistron.
This driver currently "knows" only about Fujitsu-Siemens Amilo Pro V2000
(i.e. it can detect the laptop using DMI and it contains the
keycode->key meaning mapping for this laptop) and Xeron SonicPro X 155G
(probably can't be reliably autodetected, requires a module parameter),
adding other laptops should be easy.
In addition to reporting button presses to the input layer the driver
also allows enabling/disabling the embedded wireless NIC (using the
"Wifi" button); this is done using the same BIOS interface, so it seems
only logical to keep the implementation together. Any flexibility
possibly gained by allowing users to remap the function of the "Wifi"
button is IMHO not worth it when weighted against the necessity to run
an user-space daemon to convert button presses to wifi state changes.
Signed-off-by: Miloslav Trmac <mitr@volny.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
