Changes made as suggested by Eric Miao (including fix to map_io
silly mistake!).
Originally designed by Intel, now sold by Crossbow (www.xbow.com).
Very little actually on board. The patch includes sensors and
similar as found on commonly occurring daughter boards.
Some of the drivers are not in mainline as yet as they are either
part of the IIO subsystem or need a lot of work before submission.
What is the position wrt to putting them in i2c board configs etc?
Support for these boards has been maintained outside the kernel
for a long time, but now that there is a good da9030 pmic driver
available the last major hurdle no longer exists.
All comments welcomed.
The Imote2's big brother (stargate2) will follow once any problems
with this one have been cleaned up and a few bits and bobs have
been added to the da903x driver. Hopefully the cc2420 driver will
get cleaned up and submitted in the not too distant future as
well.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I2C platform data setups.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Matrix and single key setups for all phones.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Pin configs for different generations and phones.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Our bootloader now supports ATAGS_MEM
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Some smart panel requires a delay between command sequences, while PXA
LCD controller didn't provide such one, let's emulate this by software.
A software delay marker can be inserted into the command sequence, once
pxafb_smart_queue() detects this, it flushes the previous commands and
delay for a specified number of milliseconds.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
For smart panels (LCD panel with internal framebuffer), the following
LCCR3 register bits have different meanings than the parallel one:
LCCR3_PCP - controls the L_PCLK_WR polarity
LCCR3_HSP - controls the L_LCLK_A0 polarity
LCCR3_VSP - controls the L_FCLK_RD polarity
To keep minimum change to the original parallel timing, the .lcd_conn
flags and 'pxafb_mode_info.sync' are re-used to reflect this:
LCD_PCLK_EDGE_{RISE,FALL} - configures LCCR3_PCP
sync & FB_SYNC_{HOR,VERT}_HIGH_ACT - configures LCCR3_{HSP,VSP}
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patchset provides support for the TMIO based IO controller used in the
Toshiba e-series PDAs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Fix kernel-doc notation to use correct syntax. Even though this should be
moved to where the function is actually implemented...
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
drivers/built-in.o: In function `pci_set_consistent_dma_mask':
hid-quirks.c:(.text+0x2664): multiple definition of `pci_set_consistent_dma_mask'
drivers/built-in.o: In function `pci_set_dma_mask':
hid-quirks.c:(.text+0x42c4): multiple definition of `pci_set_dma_mask'
because drivers/pci/pci.c was not seeing the definition disabling these
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The gpio setup for AM200 specific GPIO pins should be done in the AM200
code rather than in generic gumstix code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.
Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).
Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.
This machine will be used as "real user" for these new drivers.
This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add platform data necessary to support tmiofb on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.
But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).
Remove the not needed anymore dependency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Following the removal of the "->policy" usage for PXA255 in patch
459fc208ab (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.
It also cures the runtime warning that was printed each time the
frequency was changed.
Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.
Tested on an Arcom/Eurotech Viper.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit da1a3dc0eb.
The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.
Also, fix the incorrect GPIO number passed in pxa27x_init_irq().
Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Both of these symbols should be defined by a platform, or neither
should be defined. Ensure that all platforms conform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid unnecessarily pollution of the kernel's namespace by avoiding
mach/hardware.h. Include this header file where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0 is a valid GPIO number, use a negative number to specify, that this camera
doesn't have a GPIO for bus-width switching.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch makes do_hw_reset the default reboot behavior when nothing
else matches. This restores reboot functionality on gumstix basix
devices where reboot=cold is the default boot argument.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original incorrect configuration caused GPIO79_nCS_3 being overriden,
thus resulted in the NAND flash not being detected. The real PSKTSEL pin
is on GPIO104 instead of GPIO79.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
this patch adds asoc audio driver for pxa27x based Palm PDAs. I tested it for
palmtx, t5 and ld, it should work with palmz72 as well (slapin, please test).
I sent it here some time ago, but now I got to fixing bugs in it. It should
be somehow mostly ok and ready for applying.
[Converted to use snd_soc_dapm_nc_pin() and bool Kconfig -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Finally move registration of sharpsl-nand device to board-specific code.
sharpsl nand driver is now clean and simple.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.
This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit 68677ab3d0.
A smoother migration path would be making corgi_ts.c and other drivers
depending on corgi_ssp.c and corgi_lcd.c to depend on BROKEN instead,
and still allows those to exist around for some time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On Sharp SL-6000 lcd/backlight is a bit complex, so add two drivers
one for lcd-driving chip, other one for dac regulating the backlight
LEDS.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.o-hand.com/linux-mfd:
mfd: further unbork the ucb1400 ac97_bus dependencies
mfd: ucb1400 needs GPIO
mfd: ucb1400 sound driver uses/depends on AC97_BUS:
mfd: Don't use NO_IRQ in WM8350
mfd: update TMIO drivers to use the clock API
mfd: twl4030-core irq simplification
mfd: add base support for Dialog DA9030/DA9034 PMICs
mfd: TWL4030 core driver
mfd: support tmiofb cell on tc6393xb
mfd: add OHCI cell to tc6393xb
mfd: Fix htc-egpio compile warning
mfd: do tcb6393xb state restore on resume only if requested
mfd: provide and use setup hook for tc6393xb
mfd: update sm501 debugging/low information messages
mfd: reduce stack usage in mfd-core.c
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
As requested by Ian make state restore only if it's requested
by platform data: some platforms do correctly save the state of
the chip during suspend/resume, but some (like tosa) incorrectly
power off the chip at suspend, so the driver supports restoring
some bits of the tc6393xb state (not full, merely enough to support
resume on tosa). With this patch this code is disabled by default.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of using bitfields for initial gpio setup,
provide generic setup/teardown hooks that can be used
to set the gpio states, register child devices, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Rather than having everything that needs DMABOUNCE also select
ZONE_DMA, arrange for DMABOUNCE to select it instead. This is
far more sensible.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If period_cycles is 0, prescale becomes silly.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-pxa/include/mach/irqs.h:193:1: warning: "NR_IRQS" redefined
arch/arm/mach-pxa/include/mach/irqs.h:263:1: warning: this is the location of the previous definition
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As policy->governor is already set to CPUFREQ_DEFAULT_GOVERNOR in the
(always built-in) cpufreq core, we do not need to set it in the drivers.
This fixes the sparc64 allmodconfig build failure.
Also, remove a totally useles setting of ->policy in cpufreq-pxa3xx.c.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ISA IRQ renumbering broke the Viper ISA code in interesting ways.
It originally assumed that ISA interrupt were numbered in the order that
is defined by the CPLD registers. Unfortunately, this is no longer the
case.
Furthermore, the viper_irq_handler() function being a chained IRQ
handler, it must ACK the interrupt by itself, or the handler will be
immediately reentered, with the expected damages.
This fix was made possible thanks to the help of David Raeman, who
provided debug information and tested each version of this patch.
Tested-by: David Raeman <david.raeman@gmail.com>
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix build for CM-X2XX with CONFIG_RTC_DRV_V3020 unset:
CC arch/arm/mach-pxa/cm-x270.o
/mnt/sdb1/git/linux-2.6-arm/arch/arm/mach-pxa/cm-x270.c: In function 'cmx270_init':
/mnt/sdb1/git/linux-2.6-arm/arch/arm/mach-pxa/cm-x270.c:338: error: implicit declaration of function 'cmx270_init_rtc'
make[2]: *** [arch/arm/mach-pxa/cm-x270.o] Error 1
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make .power and .reset callbacks per camera instead of per host, also move
their invocation to camera drivers.
.arch/arm/mach-pxa/include/mach/camera.h | 2 -
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Some machines don't have the pullup/down on their reset
pin, so configuring the reset generating pin as input makes
them reset immediately. Fix that by making reset pin direction
configurable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:
| text data bss dec hex filename
|3826182 102384 111700 4040266 3da64a vmlinux
|3823593 101616 111700 4036909 3d992d vmlinux.nodmazone
This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.
So let's configure this zone only on machines that need split zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains Palm Zire 72 power
management support.
Depends on #5238/1
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. DRCMRxx is no longer recommended, use DRCMR(xx) instead, and
pass DRCMR index by "struct resource" if possible
2. DCSRxx, DDADRxx, DSADRxx, DTADRxx, DCMDxx is never used, use
DCSR(), DDADR(), DSADR(), DTADR(), DCMD() instead
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The initialization of mfp sysdev in pxa2xx_mfp_init() shall really be
avoided when !cpu_is_pxa2xx().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for NOR and NAND flashes on CM-X255.
The NAND flash support uses not yet merged GPIO NAND driver.
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Change CM-X255 and CM-X270 common function prefix from cmx270 to cmx2xx
- Split cmx2xx_init to common and CM-X270-specific parts
- Use dynamic assignement for DM9000 resources and led GPIOs.
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds basic support for the Mobilepro
900/c mini-laptop. At present it won't do much
more than build and boot.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds generic battery driver for wm97xx chips.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: Jürgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- use MFP-API for GPIO
- support TRIZEPS4WL module
- cleanups
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
TOUCH_PANEL_IRQ is never referenced, and set_irq_type() shouldn't
be called in this way, remove it, as well as the idp_init_irq(),
and use pxa25x_init_irq() instead.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Cliff Brake <cliff.brake@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.
Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains very basic support of Palm Zire 72.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PXA26x (PXA261/262) is actually a PXA250 with stacked Intel(R)
StartaFlash. And this can be decided by bit 3 (PKG_TYPE) of
BOOT_DEF register.
Due to this extra I/O register access, make cpu_is_pxa26x() a
public function instead of a macro.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. add a CPUID table in the comment
2. make cpu_is_pxa25x() true for PXA210/250/255/26x
3. PXA210 is treated as PXA25x, all related code modified to
reflect this
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move asm-arm/cnt32_to_63.h to include/linux/ so that MN10300 can make
use of it too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use generic pca953x which provides gpiolib interface instead of
akita-specific akita-ioexp with non-standard interface to pins.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz
Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's inital scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi
Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's inital scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now poodle/corgi/spitz have been been converted to use SPI-based
drivers, remove the now unused corgi_ssp.c and corgi_lcd.c. And
as well as the unused reference of {corgi,spitz}ssp_device.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
TODO: figure out the MFP configuration of the SSP2 which looks like
to be already configured by the boot loader, though.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.
Separated into this dedicated generic GPIO conversion patch for the
work of deprecating pxa_gpio_mode().
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MFP configuration table is reverse engineered from those
magic GAFRx_{L|U} values, and it looks much better now.
Also, the deprecated pxa_gpio_mode() invocations are removed.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct manipulation of GPIO registers are no longer encouraged, use
the new GPIO API instead. Since the GPIO has to be requested before
use, .startup and .shutdown are added to the IrDA device platform
data to request and free the GPIO.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clock alias for clock that is used by tc6393xb device on tosa.
As that chip plays pretty major part in tosa life and is currently
disabled, this is 2.4.27 material.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, we set PSPR just before entering sleep mode. However,
some platforms have different requirements for setting PSPR in
order to properly wake up.
Set PSPR earlier in the suspend cycle so that platforms can
change the setting by using a sysdev driver instead.
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce accessors for the SSP registers so that drivers don't need to
open code offsets from the MMIO base.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add power I2C support for PXA3xx processors
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves some attributes out from the platform data into the
dynamically created nand device. This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch marks some attributes as 'const' which are set only once and
never be modified by the driver. There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine. This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.
This is the first one of a set of patches which:
* allows to specify used NAND flash in the platform code and allows to turn
off the old way to specify NAND characteristics in the driver. This way did
not worked well as these characteristics depend on the platform and can not be
derived from NAND id alone.
E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but
have different timings (which are written in the common driver currently and
must be modified there).
* adds 'const' annotations at various places
Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Allow PXA IRQs to be numbered starting at 16, leaving 0 to 15 for the
ISA IRQs, if needed.
This patch depends on RMK's PXA_HAVE_BOARD_IRQS patch.
Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>
Acked-by: Russel King <linux@arm.linux.org.uk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
