Backport the "pio flush" from the libata major update to 2.6.17 for via atapi.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a byte-swap issue on PPC, found by Zang Roy-r61911
on the powerpc platform. His original patch also had some other
platform-specific changes in #ifdef's, but I'm not sure yet how to
incorporate them. Look for another patch for those (soon).
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver currently keeps local copies of the hardware request/response queue indexes.
But it expends significant effort ensuring consistency between the two views,
and still gets it wrong after an error or reset occurs.
This patch removes the local copies, in favour of just accessing the hardware
whenever we need them. Eventually this may need to be tweaked again for NCQ,
but for now this works and solves problems some users were seeing.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 60xx chips, and possibly others, incorrectly assert DEV_IRQ interrupts
on a regular basis. The cause of this is under investigation (by me and
in theory by Marvell also), but regardless we do need to deal with these events.
This patch tidies up some interrupt handler code, and ensures that we ignore
DEV_IRQ interrupts when the drive still has ATA_BUSY asserted.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interface control register of the 60xx (and later) Marvell chip
requires certain bits to always be set when writing to it. These bits
incorrectly read-back as zeros, so the pattern must be ORed in
with each write of the register. Also, bit 12 should NOT be set
(note that Marvell's own driver also had bit-12 wrong here).
While we're at it, we also now do pci_set_master() in the init code.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In some systems, it is possible that the BIOS may have enabled interrupt coalescing
for the Marvell controllers which support it. This patch adds code to detect/ack
interrupts from the chip's coalescing (combing) logic.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv_err_intr() function is invoked from the driver's interrupt handler,
as well as from the timeout function. This patch prevents it from triggering
a one-after-the-other double reset of the controller when invoked
from the timeout function.
This also adds a check for a timeout race condition that has been observed
to occur with this driver in earlier kernels. This should not be needed,
in theory, but in practice it has caught bugs. Maybe nuke it at a later date.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the lpfc driver to revision 8.1.6, which includes
the following changes:
- Fix data corruption in SCSI BUS reset path, due to reusing
the same request structure for each target.
- Change version number to 8.1.6
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Let people enable the advansys driver on x86-32, even though it's broken
on other architectures due to missing DMA mapping infrastructure.
It's used by Jeffrey Phillips Freeman <jeffreyfreeman@syncleus.com> and
possibly others.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When abort failed, the driver gets reset handleer called. In the reset
handler, driver calls 'scsi_done()' callback for same SCSI command packet
(struct scsi_cmnd) multiple times if there are multiple SCSI command packet
in the pend_list. More over, if there are entry in the pend_lsit with
IOCTL packet associated, the driver returns it to wrong free_list so that,
in turn, the driver could end up with 'NULL pointer dereference..' during
I/O command building with incorrect resource.
Also, the patch contains several minor/cosmetic changes besides this.
Signed-off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some versions of the IBM 2104-DU3 disk enclosure
have been observed to hang Inquiries to non zero
LUNs to the SES device. This device only has LUN 0,
so this patch adds it to the BLIST to prevent scsi
core from scanning beyond LUN 0.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some pioneer DVDs are apparently returning odd "not ready" status
codes that the mid-layer doesn't recognise and so passes back to the
user as errors.
This patch overhauls our not-ready handling and adds transparent retries for:
format in progress
rebuild in progress
recalculation in progress
operation in progress
Long write in progress
self test in progress
The Pioneer was actually returning "long write in progress"
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix resource leak in
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c::ahc_linux_pci_dev_probe()
Found by the coverity checker (#668)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix ahc_pci_write_config's (wrong order of arguments).
Signed-off-by: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/megaraid.c: In function `mega_internal_command':
drivers/scsi/megaraid.c:4474: warning: unused variable `flags'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one() fails before calling request_irq() but gets to
qla2x00_free_device() then it will mistakenly try to free an irq it didn't
request. It's chosing to free based on ha->pdev->irq which is always set.
host->irq is set after request_irq() succeeds so let's use that to decide
to free or not.
This was observed and tested when a silly set of circumstances lead to
firmware loading failing on a 2100.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes coverity bug id #480. Since id_array is declared as
id_array[MAX_SLOTS], the check for i>MAX_SLOTS is obviously false.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Contains the following misc fixes:
- Fix build warnings
- Race condition in lpfc_workq_post_event() could corrupt phba->work_list.
- nlp_sid was not being initialized properly
- Fix some RSCN handling during the re-discovery after Link Up event.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Additional fixes to LOGO, PLOGI, and RSCN processing
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix cleanup code in the lpfc_pci_probe_one() error code path.
This changes the original patch by:
- hardsetting the return value from lpfc_pci_probe_one() to
-ENODEV (negative value) if we fail attach
- removes the checks from lpfc_pci_remove_one() validating the
host and phba pointers as it's no longer needed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed FC protocol violation in handling of PRLO.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use asynchronous ABTS completion to speed up abort completions
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix Discovery processing for NPorts that hit nodev_tmo during discovery
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes a NULL pointer dereference spotted by the Coverity
checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Any end device that can't support any of the scanning protocols
shouldn't be scanned, so set its id to -1 to prevent
scsi_scan_target() being called for it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Equivalent of the same patch for the 3w-xxxx driver.
Signed-off-by: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_kill_request() completes requests via normal SCSI completion path
which decrements busy counts; however, requests which get passed to
scsi_kill_request() aren't holding busy counts and scsi_kill_request()
don't increment them before invoking completion path resulting in
incorrect busy counts. Bump up busy counts before invoking completion
path.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As previously reported via Michael Reed, the FC transport took a hit
in 2.6.15 (perhaps a little earlier) when we solved a recursion error.
There are 2 deadlocks occurring:
- With scan and the delete items sharing the same workq, flushing the
workq for the delete code was getting it stalled behind a very long
running scan code path.
- There's a deadlock where scsi_remove_target() has to sit behind
scsi_scan_target() due to contention over the scan_lock().
This patch resolves the 1st deadlock and significantly reduces the
odds of the second. So far, we have only replicated the 2nd deadlock
on a highly-parallel SMP system. More on the 2nd deadlock in a following
email.
This patch reworks the transport to:
- Only use the scsi host workq for scanning
- Use 2 other workq's internally. One for deletions, the other for
scheduled deletions. Originally, we tried this with a single workq,
but the occassional flushes of the scheduled queues was hitting the
second deadlock with a slightly higher frequency. In the future, we'll
look at the LLDD's and the transport to see if we can get rid of this
extra overhead.
- When moving to the other workq's we tightened up some object states
and some lock handling.
- Properly syncs adds/deletes
- minor code cleanups
- directly reference fc_host_attrs, rather than through attribute
macros
- flush the right workq on delayed work cancel failures.
Large kudos to Michael Reed who has been working this issue for the last
month.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a target is added aic79xx tries to be overly clever: it changes
the command on the fly to TEST UNIT READY and tries to requeue the
original command. Sadly this breaks SCSI compability and of course
the midlayer is getting a bit confused by it.
So we're just removing that bit of code and let the midlayer deal with
it. It's clever enough by now. And the driver code is getting simpler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It's no longer needed after the convrsion to use the linux srp.h file.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As James B. correctly noted, ahd_reset_channel() in
ahd_linux_bus_reset() should be protected by ahd_lock(). However, the
main reason for not doing so was a deadlock with the interesting
polling mechanism to detect the end a bus reset.
This patch replaces the polling mechanism with a saner signalling via
flags; it also gives us the benefit of detecting any multiple calls to
ahd_reset_channel().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Ingo Flaschberger <if@xip.at>
To support the RA4100 array from Compaq.
This patch now correctly handles SCSI_UNKNOWN types with regard to
BLIST_REPORTLUNS2 (allow it) and cdb[1] LUN inclusion (don't).
It also allows a BLIST_MAX_512 flag to restrict the maximum transfer
length to 512 blocks (apparently this is an RA4100 problem).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When spinlock debugging is turned on, a struct completion grows beyond the
size allowed for the scsi_pointer. So move the struct completion back onto
the stack. The additional memory barriers are to keep us from completing
a random piece of kernel stack if the command happens to complete after
the error handling has finished.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Encapsulate some more of the device reset processing in
preparation for SATA support.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove some unused printk macros, make some more robust, and
convert some to use standard printk macros when possible.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify the dumping of the command status area by
removing some device specific information that has proven
to not be worthwhile.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixup a check used by the ipr driver to determine if a given
device is a SCSI disk. Due to the addition of support for
attaching SATA devices, this check needs to be more robust.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Instead of NULLing the resource entry pointer when a disk
goes away to prevent any new commands being sent to it,
set the adapter resource handle to an invalid value so
new ops getting sent to it will fail with a selection timeout
response. This patch is needed for future SATA patches.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
when the sg driver is unable to setup direct IO, free that scatter
gather list prior to falling back to indirect IO
Further to this thread started by Bryan Holty:
http://marc.theaimsgroup.com/?l=linux-scsi&m=114306885116728&w=2
Here is the reworked patch again. This time it has been
tested with a program provided by Bryan.
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
