qcacld-2.0 to qcacld-3.0 propagation
Currently, driver doesn't consider tx power which was negotiated
at the time of connection for max tx power for RRM Link Measurement
Request.
Fix this by not allowing tx power more than pSessionEntry->maxTxPower.
Change-Id: Idebe6d11e05da0b3b8186e2c84ff8ad4ac124fdc
CRs-Fixed: 2021835
When Driver does disconnect as part of heartbeat failure
or kickout event, trigger fatal event to capture pktlog.
Change-Id: I43a486afeccc4acd4be542357b803d492afde9c0
CRs-Fixed: 2030718
Currently, a hard-coded enhanced multicast filter configuration is being
sent to firmware. Instead, create a set of enable/disable APIs, and
configure enhanced multicast filter based on advertised firmware
capability.
Change-Id: I488b4a921612e1081266be8831be098d755375f9
CRs-Fixed: 2078615
In the suspend path, the code waits for all active/pending scans to be
cancelled before continuing the suspend. Instead, for better power
savings, abort all active/pending scans during suspend and immediately
continue the suspend process.
Change-Id: I16a5429c00034fe58fb4c70a8dacda666ac54227
CRs-Fixed: 2073229
Fix incorrect processing of encrypted auth frame by allocating
appropriate local buffer and using correct type for frame length.
Change-Id: I87d6f4c3c43dd332d5b1877ddf4b3b46a717468b
CRs-Fixed: 2081734
Currently, numap is int and is assigned with a uint32 value from
fw which might lead to integer overflow. Also, when multiplying
the uint32 value with sizeof dest_ap could lead to int overflow
if the value of numap is close to uint32's maximum limit.
Fix/Modify numap to uint32 to be in sync with value from fw cmd.
Also add check to trim down numap value to max (10) if value is
greater than max (10).
Change-Id: I060f585c8c951807cd32b5eec75c1bad2e84a75b
CRs-Fixed: 2082665
QCA_WIFI_3_0_EMU flag is introduced for IHelium emulation
platform, where wait/error timeouts are kept for larger values.
Remove this flag for production target.
Increase tx completion drain delay to 1sec from 500ms to avoid
unwanted suspend abort.
Change-Id: Ie0633b3a2bbc9e2237039311af7417952961aada
CRs-Fixed: 2047750
qcacld-2.0 to qcacld-3.0 propagation
Update EDCA parameter if the country is in European
Union based on new ETSI RED channel access parameters.
Change-Id: I08b1a0d7cd0ee1f6985cd0810c5c4c1108e582b4
CRs-Fixed: 2078985
Skip FW memory dump in SSR case for HL SDIO solution.
HL SDIO uses the diag read API to read by 4 bytes,
which is too slow to meet SSR time requirement.
Change-Id: Iacde90ab0ec84f29f3744bf4497ec8fd8517600a
CRs-Fixed: 2071329
Vendor features are used to indicate OCE support
from driver to user space which are set based on ini
params for STA and SAP.
Change-Id: I1b9039307d5477883a2fd23e972d20234908ee24
CRs-Fixed: 2031980
Fix array out-of-bounds access while populating the BSS rate set.
The issue was seen while populating the basic supported rate
and extended rate sets.
CRs-Fixed: 2081423
Change-Id: I8626399b7f9a04dc368daa582b6a09500a7ea015
propagation from qcacld-2.0 to qcacld-3.0.
While processing setpno ioctl, input arguments are not validated
and also while parsing arguments, there is a possibility of Host
accessing memory beyond memory allocated as there is no check
whether is Host is accessing valid memory or not.
Validate input arguments and make sure Host won't access invalid
memory, while processing setpno ioctl.
Change-Id: Ica9ea56283d55282cff3ccd349e4bc1c08b80e70
CRs-Fixed: 1097868
Rx hash deinit sets hash_table to NULL, at the same time
there can be active tasklet context accessing the rx hash list.
Prevent rx hashlist access after rx hash deinit and set the netbuf
to NULL once netbuff is popped out of the list.
Change-Id: I4e30dd69ece33c3cc768842274d5307c0bf29a37
CRs-Fixed: 2049121
sap_restart_on_ch_avoid ini parameter holds good for both SAP and GO.
So to make it generic, rename to ignore_restart_on_chan_avoid_event.
Change-Id: Ic68014a71b36e00c268da50528bf5e14fd87d007
CRs-Fixed: 2027436
Driver is disabling the tdls for 5s from the last p2p-listen request
received. This is leading to tdls connection failure even after p2p
find has been stopped.
So reducing the min and default timer values 500ms and 2s respectively.
CRs-Fixed: 2078933
Change-Id: Id1ab3945d029de8154aede403b354aec99f4cd79
The function is not present as inline in the non debug build, which will
cause a compilation error.
Fix issue by having an empty inline function in the header file.
Some counters need to be defined outside of DEBUG_RX_RING_BUFFER.
Change-Id: I755616aa55c2f38bca017137e91cc469de7fbdcf
CRs-Fixed: 2004927
Make sure sta is not null before dereferencing in
lim_send_assoc_rsp_mgmt_frame function.
Change-Id: Ifb7c4a3b1e02297906bfa1b7908c27929682cf28
CRs-Fixed: 2030304
qcacld-2.0 to qcacld-3.0 propagation
Add eCSA capability record of STAs which associated to SAP.
Change-Id: I1d7892bb1dc4e490a587e8372a4bdc7f419e8b36
CRs-Fixed: 1094958
Presently during the mac open the globalmac context is memset to
zero and the based on the driver_type pe sessions will be created.
During the switch from the FTM to mission mode, pe checks the
driver mode from the mac context and tries to access the invalid
lim sessions which are not created for FTM mode.
To mitigate the issue set the driver_type in the mac context during
mac_open
CRs-Fixed: 2017035
Change-Id: Iddefd2f74afb71197c3830a51f107d86736745f1
Current driver is assigning listening interval based on beacon interval
value which is incorrect.
Listen interval should be taken based on INI value.
CRs-Fixed: 2080042
Change-Id: I0ad52a8042589604d51fc632fe3ce31547a26628
Due to multiple beacon miss issues observed in firmware,
Host is changing final bmiss count to 20 from 10.
Hence firmware can receive beacon in noisy environment.
Change-Id: I87e4a6eaec016f36ca22a057e0d9812c0b8696ff
CRs-Fixed: 2082088
