This is the long overdue conversion of sparc64 over to
the generic IRQ layer.
The kernel image is slightly larger, but the BSS is ~60K
smaller due to the reduced size of struct ino_bucket.
A lot of IRQ implementation details, including ino_bucket,
were moved out of asm-sparc64/irq.h and are now private to
arch/sparc64/kernel/irq.c, and most of the code in irq.c
totally disappeared.
One thing that's different at the moment is IRQ distribution,
we do it at enable_irq() time. If the cpu mask is ALL then
we round-robin using a global rotating cpu counter, else
we pick the first cpu in the mask to support single cpu
targetting. This is similar to what powerpc's XICS IRQ
support code does.
This works fine on my UP SB1000, and the SMP build goes
fine and runs on that machine, but lots of testing on
different setups is needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Inspired by PowerPC XICS interrupt support code.
All IRQs are virtualized in order to keep NR_IRQS from needing
to be too large. Interrupts on sparc64 are arbitrary 11-bit
values, but we don't need to define NR_IRQS to 2048 if we
virtualize the IRQs.
As PCI and SBUS controller drivers build device IRQs, we divy
out virtual IRQ numbers incrementally starting at 1. Zero is
a special virtual IRQ used for the timer interrupt.
So device drivers all see virtual IRQs, and all the normal
interfaces such as request_irq(), enable_irq(), etc. translate
that into a real IRQ number in order to configure the IRQ.
At this point knowledge of the struct ino_bucket is almost
entirely contained within arch/sparc64/kernel/irq.c There are
a few small bits in the PCI controller drivers that need to
be swept away before we can remove ino_bucket's definition
out of asm-sparc64/irq.h and privately into kernel/irq.c
Signed-off-by: David S. Miller <davem@davemloft.net>
And reuse that struct member for virt_irq, which will
be used in future changesets for the implementation of
mapping between real and virtual IRQ numbers.
This nicely kills off a ton of SBUS and PCI controller
PIL assignment code which is no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't piggy back the SMP receive signal code to do the
context version change handling.
Instead allocate another fixed PIL number for this
asynchronous cross-call. We can't use smp_call_function()
because this thing is invoked with interrupts disabled
and a few spinlocks held.
Also, fix smp_call_function_mask() to count "cpus" correctly.
There is no guarentee that the local cpu is in the mask
yet that is exactly what this code was assuming.
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch converts arch/sparc64 to kzalloc usage.
Crosscompile tested with allyesconfig.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the PCI controller drivers were doing the same thing
setting up the IOMMU software state, put it all in one spot.
Signed-off-by: David S. Miller <davem@davemloft.net>
There were three changes necessary in order to allow
sparc64 to use setup-res.c:
1) Sparc64 roots the PCI I/O and MEM address space using
parent resources contained in the PCI controller structure.
I'm actually surprised no other platforms do this, especially
ones like Alpha and PPC{,64}. These resources get linked into the
iomem/ioport tree when PCI controllers are probed.
So the hierarchy looks like this:
iomem --|
PCI controller 1 MEM space --|
device 1
device 2
etc.
PCI controller 2 MEM space --|
...
ioport --|
PCI controller 1 IO space --|
...
PCI controller 2 IO space --|
...
You get the idea. The drivers/pci/setup-res.c code allocates
using plain iomem_space and ioport_space as the root, so that
wouldn't work with the above setup.
So I added a pcibios_select_root() that is used to handle this.
It uses the PCI controller struct's io_space and mem_space on
sparc64, and io{port,mem}_resource on every other platform to
keep current behavior.
2) quirk_io_region() is buggy. It takes in raw BUS view addresses
and tries to use them as a PCI resource.
pci_claim_resource() expects the resource to be fully formed when
it gets called. The sparc64 implementation would do the translation
but that's absolutely wrong, because if the same resource gets
released then re-claimed we'll adjust things twice.
So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource()
conversion before passing it on to pci_claim_resource().
3) I was mistakedly __init'ing the function methods the PCI controller
drivers provide on sparc64 to implement some parts of these
routines. This was, of course, easy to fix.
So we end up with the following, and that nasty SPARC64 makefile
ifdef in drivers/pci/Makefile is finally zapped.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Firstly, if the direction is TODEVICE, then dirty data in the
streaming cache is impossible so we can elide the flush-flag
synchronization in that case.
Next, the context allocator is broken. It is highly likely
that contexts get used multiple times for different dma
mappings, which confuses the strbuf flushing code and makes
it run inefficiently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
