No longer need read_lock(&dev_base_lock), use RCU instead.
We also can avoid taking references on inet6_dev structs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define two symbols needed in both kernel and user space.
Remove old (somewhat incorrect) kernel variant that wasn't used in
most cases. Default should apply to both RMSS and SMSS (RFC2581).
Replace numeric constants with defined symbols.
Stand-alone patch, originally developed for TCPCT.
Signed-off-by: William.Allen.Simpson@gmail.com
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In r8169 driver MTU is used to calculate receive buffer size.
Receive buffer size is used to configure hardware incoming packet filter.
For jumbo frames:
Receive buffer size = Max frame size = MTU + 14 (ethernet header) + 4
(vlan header) + 4 (ethernet checksum) = MTU + 22
Bug:
driver for all MTU up to 1536 use receive buffer size 1536
As you can see from formula, this mean all IP packets > 1536 - 22
(for vlan tagged, 1536 - 18 for not tagged) are dropped by hardware
filter.
Example:
host_good> ifconfig eth0 mtu 1536
host_r8169> ifconfig eth0 mtu 1536
host_good> ping host_r8169
Ok
host_good> ping -s 1500 host_r8169
Fail
host_good> ifconfig eth0 mtu 7000
host_r8169> ifconfig eth0 mtu 7000
host_good> ping -s 1500 host_r8169
Ok
Bonus: got rid of magic number 8
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing "get_xstats_size" callback for the
netlink interface, which is required if "fill_xstats" is used,
as pointed out by Patrick McHardy.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.
This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.
As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.
Thanks,
Oliver
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The other error paths in front of this one have a dev_put() but this one
got missed.
Found by smatch static checker.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wang Chen <ellre923@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due commit 4b77b0a2ba, it is not more
possible to pci_restore_state() more than once without calling
pci_save_state() in the middle.
Actually running a ethtool test on s2io makes the card inactive,
and it needs to unload/reload the module to fix.
This patch just save the state just after it restore in order to
keep the old behaviour
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commits
sctp: Get rid of an extra routing lookup when adding a transport
and
sctp: Set source addresses on the association before adding transports
changed when routes are added to the sctp transports. As such,
we didn't set the socket source address correctly when adding the first
transport. The first transport is always the primary/active one, so
when adding it, set the socket source address. This was causing
regression failures in SCTP tests.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new (unrealeased to the user) sctp_connectx api
c6ba68a266
sctp: support non-blocking version of the new sctp_connectx() API
introduced a regression cought by the user regression test
suite. In particular, the API requires the user library to
re-allocate the buffer and could potentially trigger a SIGFAULT.
This change corrects that regression by passing the original
address buffer to the kernel unmodified, but still allows for
a returned association id.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit 8da645e101
sctp: Get rid of an extra routing lookup when adding a transport
introduced a regression in the connection setup. The behavior was
different between IPv4 and IPv6. IPv4 case ended up working because the
route lookup routing returned a NULL route, which triggered another
route lookup later in the output patch that succeeded. In the IPv6 case,
a valid route was returned for first call, but we could not find a valid
source address at the time since the source addresses were not set on the
association yet. Thus resulted in a hung connection.
The solution is to set the source addresses on the association prior to
adding peers.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add myself to the list of maintainers for the rt2x00 driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b8ecd988b1.
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both vlan and macvlan devices usually don't use a qdisc and immediately
queue packets to the underlying device. Propagate transmission state of
the underlying device to the upper layers so they can react on congestion
and/or inform the sending process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ->ndo_hard_start_xmit() callbacks are only permitted to return
one of the NETDEV_TX codes. This prevents any kind of error propagation for
virtual devices, like queue congestion of the underlying device in case of
layered devices, or unreachability in case of tunnels.
This patches changes the NET_XMIT codes to avoid clashes with the NETDEV_TX
codes and changes the two callers of dev_hard_start_xmit() to expect either
errno codes, NET_XMIT codes or NETDEV_TX codes as return value.
In case of qdisc_restart(), all non NETDEV_TX codes are mapped to NETDEV_TX_OK
since no error propagation is possible when using qdiscs. In case of
dev_queue_xmit(), the error is propagated upwards.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of rcv_nxt allows to discern whether the skb
was out of place or tp->copied. Also catch fancy combination
of flags if necessary (sadly we might miss the actual causer
flags as it might have already returned).
Btw, we perhaps would want to forward copied_seq in
somewhere or otherwise we might have some nice loop with
WARN stuff within but where to do that safely I don't
know at this stage until more is known (but it is not
made significantly worse by this patch).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ieee802154 initialisation to subsys_initcall call, so that
wpan-phy class is initialised before all devices (thus saving us from
oops during bootup).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
We have two implementations of the compat_ioctl handling for ATM, the
one that we have had for ages in fs/compat_ioctl.c and the one added to
net/atm/ioctl.c by David Woodhouse. Unfortunately, both versions are
incomplete, and in practice we use a very confusing combination of the
two.
For ioctl numbers that have the same identifier on 32 and 64 bit systems,
we go directly through the compat_ioctl socket operation, for those that
differ, we do a conversion in fs/compat_ioctl.c.
This patch moves both variants into the vcc_compat_ioctl() function,
while preserving the current behaviour. It also kills off the COMPATIBLE_IOCTL
definitions that we never use here.
Doing it this way is clearly not a good solution, but I hope it is a
step into the right direction, so that someone is able to clean up this
mess for real.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling for SIOCSHWTSTAMP is broken on architectures
with a split user/kernel address space like s390,
because it passes a real user pointer while using
set_fs(KERNEL_DS).
A similar problem might arise the next time somebody
adds code to dev_ifsioc.
Split up dev_ifsioc into three separate functions for
SIOCSHWTSTAMP, SIOC*IFMAP and all other numbers so
we can get rid of set_fs in all potentially affected
cases.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Wake on LAN (WOL) reception and waking the device up from
this signal via the ethtool interface. Currently we are only supporting
the magic-packet variant of wakeup.
WOL is enabled by specifying a second interrupt resource to the driver
which indicates where the interrupt for the WOL is being signalled. This
then enables the necessary ethtool calls to leave the device in a state
to receive WOL frames when going into suspend.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values of r_idx and rx_ring are not used after the last time they
are set in ixgbe_msix_clean_rx(), so they can be removed.
Signed-off-by: Ali Gholami Rudi <ali@rudi.ir>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason for this lock to be reader/writer since
the reader only has lock held for a very brief period.
The overhead of read_lock is more expensive than spinlock.
Compile tested only, I am not a decnet user.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing locking in the case of auto binding to the
default device. The address list might change while this code is looking
at the list.
Compile tested only, I am not a decnet user.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The full_name_hash function does not produce well distributed values in
the lower bits, so most code uses hash_32() to fold it. This is really
a bug introduced when name hashing was added, back in 2.5 when I added
name hashing.
hash_32 is all that is needed since full_name_hash returns unsigned int
which is only 32 bits on 64 bit platforms.
Also, there is no point in using hash_32 on ifindex, because the is naturally
sequential and usually well distributed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to change the frame routing to direct all frames to the
management fifo during suspend. This is now done by the firmware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling gfar_clean_tx_ring() the driver grabs an irqsave
spinlock, and then tries to recycle skbs. But since
skb_recycle_check() returns 0 with IRQs disabled, we'll never
recycle any skbs.
It appears that gfar_clean_tx_ring() and gfar_start_xmit() are
mostly idependent and can work in parallel, except when they
modify num_txbdfree.
So we can drop the lock from most sections and thus fix the skb
recycling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_error() can arrive at the middle of gfar_start_xmit() processing,
and so it can trigger transfers of BDs that we don't yet expect to
be transmitted.
Fix this by locking the tx queues in gfar_error().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We obviously want to write a modified 'temp' value back to the
register, not the saved IRQ flags.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fba4ed030c ("gianfar: Add Multiple
Queue Support") introduced the following build failure:
CC gianfar.o
gianfar.c: In function 'gfar_restore':
gianfar.c:1249: error: request for member 'napi' in something not a structure or union
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is OK to poll with disabled IRQs, so remove the warning.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers try to recycle SKBs in their polling routine, but we
generally don't know the context in which the polling will be called,
and the skb recycling itself may require IRQs to be enabled.
This patch adds irqs_disabled() test to the skb_recycle_check()
routine, so that we'll not let the drivers hit the skb recycling
path with IRQs disabled.
As a side effect, this patch actually disables skb recycling for some
[broken] drivers. E.g. gianfar driver grabs an irqsave spinlock during
TX ring processing, and then tries to recycle an skb, and that caused
the following badness:
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
------------[ cut here ]------------
Badness at kernel/softirq.c:143
NIP: c003e3c4 LR: c423a528 CTR: c003e344
...
NIP [c003e3c4] local_bh_enable+0x80/0xc4
LR [c423a528] destroy_conntrack+0xd4/0x13c [nf_conntrack]
Call Trace:
[c15d1b60] [c003e32c] local_bh_disable+0x1c/0x34 (unreliable)
[c15d1b70] [c423a528] destroy_conntrack+0xd4/0x13c [nf_conntrack]
[c15d1b80] [c02c6370] nf_conntrack_destroy+0x3c/0x70
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Stephen Rothwell:
--------------------
Today's linux-next build (x86_64 allmodconfig) produced this warning:
net/ipv6/addrconf.c: In function 'inet6_dump_ifinfo':
net/ipv6/addrconf.c:3833: warning: unused variable 'err'
Introduced by commit 84d2697d96 ("ipv6:
speedup inet6_dump_ifinfo()").
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
I may have botched my merge conflict resolution instructions for Dave...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function to avoid doing read_lock().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also needs to be optimized for large number of devices.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When showing device statistics use RCU rather than read_lock(&dev_base_lock)
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to other cases where for_each_netdev_rcu
can be used when gathering information.
By inspection, don't have platform or cross-build environment
to validate.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to walk list of network devices in qdisc dump.
This could be optimized for large number of devices.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not need to use read_lock(&dev_base_lock), use RCU instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an RCU macro for continuing search, useful for some
network devices like vlan.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change udp6_portaddr_hash() to use ipv6_addr_v4mapped()
inline instead of ipv6_addr_type().
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use for_each_netdev_rcu() and dont lock dev_base_lock anymore
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the SIT DF bit handling using the new IPIP DF
code. The only externally visible effect should be the case where
PMTU is enabled and the MTU is exactly 1280 bytes. In this case the
previous code would send packets out with DF off while the new code
would set the DF bit. This is inline with RFC 4213.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>
