Swing/emphasis settings in NVRAM were not being honoured due
to the driver not converting the serial-link options from LE
to host-endian format.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If the Get Port Database call fails during local-loop
update, then schedule the DPC routine to perform a rescan as
the firmware would have updated the Get ID List port-entries
of their new state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Small changes to register retrieval and order as per latest
firmware specification.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Driver would not correctly re-enable the write-protection
bits of the flash part after updates.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Problem report (against 2.4.x driver) from Jeff Layton
<jlayton@redhat.com>:
An OEM noticed that the U6 qla2200 driver would hang for
around 2 minutes at boot time and then proceed normally. I
found that the delay was occurring when loading the new
firmware into the card, and was due to a
schedule_timeout(10) added to the bottom of the polling
loop.
Some testing showed that the load ram operation on the card
was very quick (on the order of a couple of jiffies), but
the sleep in the polling loop was making each operation take
around 25-30.
The attached patch corrects this by making it skip sleeping
during the load ram operation, since I believe we only do
that when the module is plugged in. It also skips sleeping
if the mbox_int flag got set during the current loop.
This corrected the hang on my test setup, and OEM also
confirmed that it corrected the problem for them.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mailbox commands are polled for completion during ISP
initialization. During potentially 'long' mailbox commands
(i.e. fabric login), we really don't want a busy-wait delay
to potentially trigger a (benign) soft-lockup BUG().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no point in displaying the message during a valid
underrun case. Limit the message to potentially problematic
cases.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The initial-control-block references are not always correct
as the use-node-name qualifier during NVRAM configuration
will cause the firmware to use the portname as a base for
the nodename.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com:
We cannot handle filesystems like XFS becuase of the pages they
are sending us. We had thought page_count could be used to
work around this, but the correct test is for PageSlab.
The proper solution is to figure out what type of pages
filesystems can use so we do not have to add tests like
this or handle it in the block layer for all network block drivers
but the issue still has not been resolved on fs-devel
so we are sending this patch as a temporary fix.
This is last patch just in case it is Nakd with the explanation
that we need to push the correct fix through fs-devel, mm
or the block layer. The rest of the patchset can live without
the patch, but the driver will not work with filesystems like
XFS.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When we run the xmit code from queuecomand the stack trace
gets too deep. The patch runs the xmit code from the scsi_host
work queue. This fixes 4k stack and xfs support and should
fix the st and sg stack usage bugs.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.
The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.
This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>:
We cannot use page_address becuase some pages could be highmem.
Instead, we can use sock_no_sendpage which does kmap for us.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Users can write to a page while we are sending it and making
digest calculations. This ends up causing us to retry the command
when a digest error is later reported. By using sock_no_sendpage
when data digests are calculated we can avoid a lot of (not all but it
helps) the retries becuase sock_no_sendpage is not zero copy.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We should be taking the host_lock instead of the conn lock when
checking host_busy.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We need to check the ISCSI_FLAG_DATA_* flags.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove extra whitespaces.
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert a the 3w-9xxx.c and 3w-xxxx.c drivers to use mutexes instead
of semaphores. Untested, but compiles and looks obviously correct.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We will be mapping the RAID volumes in mptsas to a reserved
channel that
is one larger than the anticapated number of ports on the direct
attached host
adapter.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When James Smart fixed the issue of the userspace scan atributes
crashing the system with the FC transport class he added a patch to
let the transport class check if the parent is valid for a given
transport class.
When adding support for the integrated raid of fusion sas devices
we ran into a problem with that, as it didn't allow adding virtual
raid volumes without the transport class knowing about it.
So this patch adds a user_scan attribute instead, that takes over from
scsi_scan_host_selected if the transport class sets it and thus lets
the transport class control the user-initiated scanning. As this
plugs the hole about user-initiated scanning the target_parent hook
goes away and we rely on callers of the scanning routines to do
something sensible.
For SAS this meant I had to switch from a spinlock to a mutex to
synchronize the topology linked lists, in FC they were completely
unsynchronized which seems wrong.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the SCSI transport class code to use a mutex rather than a
semaphore.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The problem in dpt_i2o could be the pci config space accesses it
triggers as it loads, dangerous to do if there is any I/O activity going
on in the other driver (probable if a boot driver I guess).
I approve this patch to dpt_i2o.c, and am applying it to the Adaptec
branch of the driver.
Thanks for the investigation Ryoji.
---
In linux 2.6.15, data transfer does hang when both dpt_i2o
and i2o_block drivers are loaded.
It seems that location of pci_request_regions() are wrong.
I moved it just behind pci_enable_device() like other drivers,
and it becomes fine.
Signed-off-by: Ryoji Kamei <kamei@miraclelinux.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To avoid the "sda: got wrong page" message, the ServeRAID driver
should be setting flags indicating that the Mode Sense commands are
not supported.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add fc_host attribute permanent_port_name which is
used to show the port name of the primary port -
the port that initially logged into the fabric.
For a virtual port (registered via the primary port with
FDISC command) it is useful to know not only its (virtual)
port name but also the permanent port name.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
split each ioctl handled in sr_audio_ioctl into a function of it's own.
This cleans the code up nicely, and allows various places in sr_ioctl
to call these helpers directly instead of going through the multiplexer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
LLDDs should never see REQ_BLOCK_PC requests, we can handle them just
fine in the core code. There is a small behaviour change in that some
check in sr's rw_intr are bypassed, but I consider the old behaviour
a bug.
Mike found this cleanup opportunity and provdided early patches, so all
the credit goes to him, even if I redid the patches from scratch beause
that was easier than forward-porting the old patches.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We need to iterate over all children when removing and expander, else
stale objects will be around after host removal. This fixes the oops
Eric Moore saw when removing and reloading mptsas.
Also don't try the scsi_remove_target call unless operating on an end
device. The current unconditional call is harmless but confusing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While trying to get SUSE's SLES9 working on system with more than 4GB we've
noticed that SCSI layer happilly passes addresses over 4GB to the buslogic
driver, which is quite a big problem as buslogic can generate only 32bit
busmastering cycles.
Fortunately in the current kernels this problem does not exist anymore as
SCSI layer now assumes 4GB capable device by default, but it is still good
idea to pass correct device structure to the SCSI layer. If nothing else,
/sys/block/sda/device now points to
/sys/devices/pci0000:00/0000:00:10.0/host0/... instead of
/sys/devices/platform/host0/... like it did in the past.
Change does nothing for ISA based BusLogic adapters, they'll still end
under platform (and they are probably broken for long time as I do not see
anything forcing ISA 16MB limit for them).
Signed-off-by: Petr Vandrovec <petr@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This takes us past the old 1.x version of the SCSI driver and the 2.x
version of the aic website version to reflect the full incorporation
of both branches.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
SCSI-1 CD drives can't do MRW or be opened for writing, so mask off
those capabilities.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn.
Move the README from the driver directory to the Documentation directory.
Updated the documentation, added descriptions for cards that
were missing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn.
The Jaguar and Corsair class of adapters (2410, 2810, 2610, 21610, CERC)
perform better (about 10% better read performance, write performance
neutral) with current Firmware if the OS limits the number of scatter
gather elements to 17 per request.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
Provide more accurate adapter information.
Allows the Adapter Firmware to override the Adapter product
information.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
If the adapter has not instructed us otherwise that it can handle a
'large' FIB, then it can handle at most a 2KB FIB.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We need to clear the backpointer on rphy removal, else we'll run into
problems with host removal after a device has been hot unplugged.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
the scsi layer is using semaphores in a mutex way, this patch converts
these into using mutexes instead
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is doing a rather stupid mod_timer allegedly to "give
request sense more time to complete". This is illegal and pointless,
so just eliminate it. Also eliminate all the other uses of struct
timer_list in the driver, which are mostly bogus.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original From: Adrian Bunk
Here's a composite patch with Adrian's original additions and
help-text with the new Kconfig variable SCSI_QLA_FC.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding defines for RAID10 and RAID50 levels, in preparation
of adding RAID Transport support in the mpt fusion drivers.
(BTW: IME is RAID10, and IM is RAID1).
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
we always set ->SCp.ptr to physical address of buffer; for DMA that's
just what we need, but we end up using it as virtual address in PIO
case of esp_do_data(), with obvious breakage as soon as memory mapping
becomes non-trivial. The fix is obvious.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
oktagon_esp is described as modular. However, drivers/scsi/Makefile doesn't
handle it right - it's multi-object module, with one of the parts being built
from .S. Current makefile tries to declare each part a module of its own;
that not only wouldn't work (oktagon_io.o doesn't have the right parts for
that), it actually doesn't even build since kbuild doesn't believe in
single-object modules built from .S. Turned into proper multi-object
module...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
in amigahw.h custom renamed to amiga_custom, in drivers with few instances the
same replacement, in the rest - #define custom amiga_custom in driver itself
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.
Remove inclusion in various drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sg_page_malloc should clear the data buffer, not that extent of mem_map.
This fixes Jesper's sg_page_free "Bad page states"
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch works around a problem with spurious interrupts seen at boot time when
a MAXTOR 6H500F0 drive is present. An ATA interrupt condition is mysteriously
present at start of day. If we took too long in issuing the first command,
the kernel would basically get tired of the spurious interrupts and turn the interrupt
off. Issuing the first command essentially causes the interrupt condition to
get acknowledged.
I haven't seen this happen with any other drives.
What I basically do is ack ATA status by reading it regardless of whether we're
expecting to have to handle an interrupt. This clears the start-of-day anomalous
interrupt condition, and keeps the kernel from disabling that interrupt due to
too many spurious interrupts.
Also, I fixed a bug where hotplug interrupts weren't getting acknowledged as handled
in the ISR. This was not the cause of the spurious interrupts, but it's the right
thing to do anyway.
Signed-Off-By: Andrew Chew
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch moves the SCSI softirq handling to the block layer version.
There should be no functional changes.
Signed-off-by: Jens Axboe <axboe@suse.de>
Many ARM drivers do not need to include asm/irq.h - remove this
unnecessary include from some ARM drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HDIO_GETGEO is implemented in most block drivers, and all of them have to
duplicate the code to copy the structure to userspace, as well as getting
the start sector. This patch moves that to common code [1] and adds a
->getgeo method to fill out the raw kernel hd_geometry structure. For many
drivers this means ->ioctl can go away now.
[1] the s390 block drivers are odd in this respect. xpram sets ->start
to 4 always which seems more than odd, and the dasd driver shifts
the start offset around, probably because of it's non-standard
sector size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@suse.de>
Cc: <mike.miller@hp.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo Giarrusso <blaisorblade@yahoo.it>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds suspend patch to libata, and ata_piix in particular. For
most low level drivers, they should just need to add the 4 hooks to
work. As I can only test ata_piix, I didn't enable it for more
though.
Suspend support is the single most important feature on a notebook, and
most new notebooks have sata drives. It's quite embarrassing that we
_still_ do not support this. Right now, it's perfectly possible to
suspend the drive in mid-transfer.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make drivers that use directly PC parport HW depend on PARPORT_PC rather than
HW independent PARPORT.
Signed-off-by: Marko Kohtala <marko.kohtala@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reflect changes in SCSI midlayer and updated to use new
ordered request implementation
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
All ordered request related stuff delegated to HLD. Midlayer
now doens't deal with ordered setting or prepare_flush
callback. sd.c updated to deal with blk_queue_ordered
setting. Currently, ordered tag isn't used as SCSI midlayer
cannot guarantee request ordering.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
add @uptodate argument to end_that_request_last() and @error
to rq_end_io_fn(). there's no generic way to pass error code
to request completion function, making generic error handling
of non-fs request difficult (rq->errors is driver-specific and
each driver uses it differently). this patch adds @uptodate
to end_that_request_last() and @error to rq_end_io_fn().
for fs requests, this doesn't really matter, so just using the
same uptodate argument used in the last call to
end_that_request_first() should suffice. imho, this can also
help the generic command-carrying request jens is working on.
Signed-off-by: tejun heo <htejun@gmail.com>
Signed-Off-By: Jens Axboe <axboe@suse.de>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The distinction between hotplug and uevent does not make sense these
days, netlink events are the default.
udev depends entirely on netlink uevents. Only during early boot and
in initramfs, /sbin/hotplug is needed. So merge the two functions and
provide only one interface without all the options.
The netlink layer got a nice generic interface with named slots
recently, which is probably a better facility to plug events for
subsystem specific events.
Also the new poll() interface to /proc/mounts is a nicer way to
notify about changes than sending events through the core.
The uevents should only be used for driver core related requests to
userspace now.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ignore all files generated from *_shipped files, plus a few others.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The oops is characteristic of the underlying device being removed from
visibility before the class device, and sure enough we do device_del()
before transport_unregister() in the scsi_target_reap() routines. I've
no idea why this is suddenly showing up, since the code has been in
there since that function was first invented. However, I've confirmed
this fixes Andrew Vasquez's boot oops.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch prevents libata from incorrectly modifying inquiry
VPD pages and command support data from ATAPI devices. I have tested
the patch with a SATA ATAPI tape drive on an AHCI controller.
Patch is against kernel 2.4.32 with 2.4.32-libata1.patch applied.
Anthony J. Battersby
Cybernetics
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Miquel van Smoorenburg <miquels@cistron.nl> forwarded me this fix to
resolve a deadlock condition that occurs due to the API change in
2.6.13+ kernels dropping the host locking when entering the error
handling. They all end up calling adpt_i2o_post_wait(), which if you
call it unlocked, might return with host_lock locked anyway and that
causes a deadlock.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compile warnings with current scsi-misc git tree
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_reap_target() was desgined to be called from any context.
However it must do a device_del() of the target device, which may only
be called from user context. Thus we have to reimplement
scsi_reap_target() via a workqueue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When the sym1 driver was in the tree, it used to share various parts of
its infrastructure with the ncr driver. Now it's gone, these files are
just an annoyance, so merge sym53c8xx_comm.h into ncr53c8xx.c and merge
sym53c8xx_defs.h into ncr53c8xx.h.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ncr53c8xx driver had its own loop to print scsi messages. Use the
SPI one instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This update now allows this driver to be used on big endian bus
machines that aren't parisc. To do that, the driver must set a
CONFIG_53C700_BE_BUS in Kconfig to compile the right macro versions.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In the scenario that a link was broken, the devloss timer for each
rport was expire at roughly the same time, causing lots of "delete"
workqueue items being queued. Depth is dependent upon the number of
rports that were on the link.
The rport target remove calls were calling flush_scheduled_work(),
which would interrupt the stream, and start the next workqueue item,
which did the same thing, and so on until recursion depth was large.
This fix stops the recursion in the initial delete path, and pushes it
off to a host-level work item that reaps the dead rports.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce a new helper, print_nego() to handle SDTR/WDTR/PPR.
Split out the guts of show_spi_transport_period_helper() into period_to_str()
and use it in print_nego to get the period factor conversion right.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace the custom NO_*_MSGS definitions with uses of ARRAY_SIZE.
This fixes a bug in the definition of NO_EXTENDED_MSGS.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A missing comma meant that "Ordered Queue Tag" and "Ignore Wide Residue"
were being concatenated together.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rename scsi_print_msg to spi_print_msg and move its prototype from
scsi_dbg.h to scsi_transport_spi.h
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_print_msg() is an SPI-specific concept. This patch moves it from
constants.c to scsi_transport_spi.c and updates the Kconfig to link in
the SPI class for the drivers which use scsi_print_msg().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This merge is pretty extensive. The conflict is over the new
req->retries parameter, so I had to change the prototype to
scsi_setup_blk_pc_cmnd() and the usage in sd, sr and st.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Kai minus last sg_segs clearing which was merged already.
> > Was there a oops or lockup or any debug output you can send me? I will try
> > some more large request tests with scsi_debug. You also have to compile your
> > kernel with SCSI_MAX_PHYS_SEGMENTS == 255 to get larger requests now.
>
It was an oops in sgl_unmap_user_pages(). The reason is this:
/* XXX: just for debug. Remove when PageReserved is removed */
BUG_ON(PageReserved(page));
I was using /dev/zero as input and it triggers this. When I used a file as
input, this did not trigger. Should this BUG_ON be removed?
In the same log I noticed that there was another ->sg_segs inconsistency.
Also, the field ->last_SRpnt was not reset when scsi_execute_async()
failed. This caused the error message "Async command already active"
later and prevented proper close.
While doing the changes, I noticed that the current code (since
2.6.0-test4) does not set the pages dirty when reading with direct i/o.
All of these st problems (including the one I sent earlier) are fixed in
the patch at the end of this message. These fixes should probably be
included already in 2.6.15.
After these fixes, the tape seems to operate as expected. Without other
changes, the largest block size with sym53c896 SCSI adapter is 384 kB. The
maximum number of sg segments is set to 96 and clustering is disabled in
the driver. 96 x 4 kB = 384 kB. OK.
I enabled clustering and set max_sectors to 10000 in the SCSI HBA driver.
Now the block size limit is 5000 kB as expected.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- export __blk_put_request and blk_execute_rq_nowait
needed for async REQ_BLOCK_PC requests
- seperate max_hw_sectors and max_sectors for block/scsi_ioctl.c and
SG_IO bio.c helpers per Jens's last comments. Since block/scsi_ioctl.c SG_IO was
already testing against max_sectors and SCSI-ml was setting max_sectors and
max_hw_sectors to the same value this does not change any scsi SG_IO behavior. It only
prepares ll_rw_blk.c, scsi_ioctl.c and bio.c for when SCSI-ml begins to set
a valid max_hw_sectors for all LLDs. Today if a LLD does not set it
SCSI-ml sets it to a safe default and some LLDs set it to a artificial low
value to overcome memory and feedback issues.
Note: Since we now cap max_sectors to BLK_DEF_MAX_SECTORS, which is 1024,
drivers that used to call blk_queue_max_sectors with a large value of
max_sectors will now see the fs requests capped to BLK_DEF_MAX_SECTORS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
convert st to always send scatterlists and kill scsi_request
usage.
This is the same as last time as it was posted, but with Kai's patches
merged and we now pass the bytes value to scsi_execute_async.
TODO:
- move DIO code to common place or make block layers usable for ULDs.
- move buffer allocation code to common place for all ULDs to use. And
make buffer allocation code handle all queue limits so we can find
out about problems before calling scsi_execute_async.
- move indirect (copy_to/from_user) paths commone place or make block
layers usable for ULDs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert sg to always send scatterlists, and kill scsi_request usage.
TODO:
- move DIO code to common place or make block layers usable for ULDs.
- move buffer allocation code to common place for all ULDs to use. And
make buffer allocation code obey all queue limits so we can find
out about problems before calling scsi_execute_async. Currently, sg.c
could allocate a buffer that is too large, and send the request
to scsi_execute_async. scsi_execute_async will then check it against
all the queue limits and return a failure in this case. It would nicer
to know about the queue limit violation right away.
- move indirect (copy_to/from_user) paths commone place or make block
layers usable for ULDs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add kmemcache of scsi io contexts.
In the future when we finalize on where these functions will live
we can add a mempool for it and do a bioset for out REQ_BLOCK_PC
bios. This is needed becuase the dm-multipath handlers will
want to use the scsi_exectute* functions for failover and we cannot
have them and the bio device allocating from the same mempool.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sd does not allow scsi_io_completion to retry commands for
SG_IO requests, and it make sense that it should not happen for st
SG_IO commands too. If for st we hit the bottom of scsi_io_completion
we will probably screw things up pretty bad. This patch returns to the
block layer that the whole command completed and relies on the caller to check
the request errors field. For initialization commands like in sd, this adds
the previous behavior where scsi_io_completion did not process the error.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For tape we need to control the retries. This patch adds a retries
counter on the request for REQ_BLOCK_PC commands originating from
scsi_execute* to use. REQ_BLOCK_PC commands comming from the block
layer SG_IO path continue to use the retires set in the ULD init_command.
(scsi_execute* does not set the gendisk so we do not execute
the init_command in that path).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi helpers to create really-large-requests and convert
scsi-ml to scsi_execute_async().
Per Jens's previous comments, I placed this function in scsi_lib.c.
I made it follow all the queue's limits - I think I did at least :), so
I removed the warning on the function header.
I think the scsi_execute_* functions should eventually take a request_queue
and be placed some place where the dm-multipath hw_handler can use them
if that failover code is going to stay in the kernel. That conversion
patch will be sent in another mail though.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi_add_host() failure handling for aic7xxx
Also silence a compiler warning :
drivers/scsi/aic7xxx/aic7xxx_osm.c: In function `ahc_linux_register_host':
drivers/scsi/aic7xxx/aic7xxx_osm.c:1100: warning: ignoring return value of `scsi_add_host', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi_add_host() failure handling for aic79xx
Also silence a compiler warning :
drivers/scsi/aic7xxx/aic79xx_osm.c: In function `ahd_linux_register_host':
drivers/scsi/aic7xxx/aic79xx_osm.c:1099: warning: ignoring return value of `scsi_add_host', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This follows on from Jens' patch and consolidates all of the ULD
separate handlers for REQ_BLOCK_PC into a single call which has his
fix for our direction bug.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since nobody has offered an explanation for why the sd driver makes a
write-protect check only for devices with removable media, I'm submitting
this patch to get rid of the removable-media test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Add functionality to run in polled mode only. Includes run time
attribute to enable mode.
- Enable runtime writable hba settings for coallescing and delay parameters
Customers have requested a mode in the driver to run strictly polled.
This is generally to support an environment where the server is extremely
loaded and is looking to reclaim some cpu cycles from adapter interrupt
handling.
This patch adds a new "poll" attribute, and the following behavior:
if value is 0 (default):
The driver uses the normal method for i/o completion. It uses the
firmware feature of interrupt coalesing. The firmware allows a
minimum number of i/o completions before an interrupt, or a maximum
time delay between interrupts. By default, the driver sets these
to no delay (disabled) or 1 i/o - meaning coalescing is disabled.
Attributes were provided to change the coalescing values, but it was
a module-load time only and global across all adapters.
This patch allows them to be writable on a per-adapter basis.
if value is 1 :
Interrupts are left enabled, expecting that the user has tuned the
interrupt coalescing values. When this setting is enabled, the driver
will attempt to service completed i/o whenever new i/o is submitted
to the adapter. If the coalescing values are large, and the i/o
generation rate steady, an interrupt will be avoided by servicing
completed i/o prior to the coalescing thresholds kicking in. However,
if the i/o completion load is high enough or i/o generation slow, the
coalescion values will ensure that completed i/o is serviced in a timely
fashion.
if value is 3 :
Turns off FCP i/o interrupts altogether. The coalescing values now have
no effect. A new attribute "poll_tmo" (default 10ms) exists to set
the polling interval for i/o completion. When this setting is enabled,
the driver will attempt to service completed i/o and restart the
interval timer whenever new i/o is submitted. This behavior allows for
servicing of completed i/o sooner than the interval timer, but ensures
that if no i/o is being issued, then the interval timer will kick in
to service the outstanding i/o.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Release task management command before counting outstanding commands.
TMF was being erroneously counted as an active outstanding command.
- Serialize EH calls and block requests when EH function is running.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove locking wrappers around error handlers. Wrappers were added in
early 2.6.13 api change
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Remove unnecessary scsi_block_requests calls on rport deletes.
This was deadlocking the sdev removals as they wanted to flush commands.
- No longer block requests when adding the remote port (to block
discovery). Instead, register, then change port role. Maps to Qlogic
behavior, and closer to the register-node-upon-first-ELS behavior.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cause: Link bounces were causing discovery ELS's to be killed.
Driver was not properly flushing ELS commands upon the subsequent
link bounces. Thus, processing of ELS post link bounce erroneously
assumed discovery failure and device loss.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Miscellaneous Cleanups:
- Remove ProgType READ_REV mailbox command value check in lpfc_config_port_prep.
- Convert simple printk to an lpfc_printf_log in queuecommand.
- Modify lpfc_abort_handler message 0749 to display more accurate text and data.
- Minor style cleanup: fix 3 long lines in lpfc_hw.h
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the vendor, model and rev fields in scsi_device pointers to const
and update a few prototypes of functions using them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
check header digest for cmd and mgmt tasks
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
High queue depth was a problem for some targets so make queue_depth adjustable
From Mike Christie
Make default queue_depth a little lower
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From Wang Zhenyu:
data digest fix (the bug caused data corruption w/Wasabi StorageBuilder target)
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from Wang Zhenyu:
Must check SCSI CMD and R2T response according to the spec
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From tomof@acm.org:
There is one more issue about Equallogic systems. They send
re-direction info with FIN. I think that the kernel module needs to
let iscsid to read data from the socket before killing it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Must check only valid opcode bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Rather than print a list of targets at driver init time, print each
disabled target as we attempt to scan it.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The NVRAM for both Tekram and Symbios boards allows the user to set the
speed and width for individual targets. I took that code out in March
2004 when we introduced Domain Validation, but it seems there's still
a legitimate need for it in some configurations.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sym_show_msg was almost a duplicate of scsi_print_msg, except not as
featureful. So use the common code instead.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Now that this constant has been added to dma-mapping.h, we don't need our
own definition
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The upper layer doesn't send these down since 2.4.x (or 2.6 in
practice), so no need to handle it. Inline sym_setup_data_pointers
into its only caller so we can fail gracefully in the case we'd get
one neverless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Allocate the lcb in slave_alloc and free it in slave_destroy. This allows
us to remove all the code that checks to see if it's already been allocated.
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SYM_OPT_SNIFF_INQUIRY define is never set any more, and the
sym_sniff_inquiry() function doesn't exist
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
