pxa2xx_i2s_resume is :
- unconditionnaly setting SACR0_ENB
- unsetting SACR0_ENB in saved SACR0 pxa_i2s.sacr0
fix these.
In pxa2xx_i2s_{resume,suspend}, save/restore registers even
when !dai->active.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
i2s_clk is 'put' for no reason in pxa2xx_i2s_shutdown.
Now we 'get' i2s_clk at probe and 'put' it at driver removal or when
probe fails.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- hw_params enables both RPL and REC functions each time : Enable the
appropriate function in pxa2xx_i2s_trigger.
- pxa2xx_i2s_shutdown disables i2s anytime one of RPL or REC function is
off : Turn it off only when both functions are off.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we are in a know good state at end of probe :
Reset FIFO logic and registers, and make sure REC and RPL functions
along with FIFO service are disabled (SACR0_RST enables REC and RPL).
Resetting loses current settings so remove reset from stream startup.
Now reset occurs only at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Resending the patch after fixing the minor issues.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reset FIFO logic and registers, and make sure REC and RPL functions along
with FIFO service are disabled at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The inputs of the twl4030 codec can be mixed, so we will use the mixer
DAPM for the analog microphone registers(0x05, 0x06), but if we enable
more than one input at the same time, the input impedance of the input
amplifier will be reduced.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the card was not instantiated in snd_soc_instantiate_card, calling
soc-remove will crash because some of codec, cpu_dai and card .remove
methods are called twice.
Fix this by returning from soc_remove immediately.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC uses the standard ALSA data format definitions to specify the wire
format used between the CPU and CODEC. Since the ALSA data formats all
include the endianess of the data but this information is not relevant
by the time the data has been encoded onto the serial link to the CODEC
this means that either all the CODEC drivers need to declare both big and
little endian variants or the core needs to fix up the format constraints
specified by CODEC drivers.
For now take the latter approach - this will need to be revisited if any
CODECs are endianness dependant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC driver for AT91SAM9260-based AFEB9260 board
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Copy-paste error: TWL4030_PRECKL_GAIN >> TWL4030_PRECKR_GAIN
It has not caused problems, since
TWL4030_PRECKL_GAIN == TWL4030_PRECKR_GAIN == 0x30
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the magic 0x80 value with a suitable macro definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the VIBRA output on TWL4030 codec.
The VIBRA output can be driven with audio data or with
local vibrator driver.
Add the needed DAPM elements and routes for the VIBRA output and
controls for the VIBRA driver configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the ASoC side of the board support for the Crossbow
IMB400 daughter board.
Thanks to Crossbow for considerable assistance.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add voice digital loopback (sidetone) to the twl4030
driver. It mixes voice uplink attenuated (by sidetone gain) with
voice downlink when the codec is working in option2 (voice/audio
mode).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voice downlink analog bypass switch. It follows
the same approach as in other analog bypass switches.
DAC switch is moved from 'DAC Voice' to 'Analog Voice Playback Mixer',
that will also allow voice DAC to be powered in digital voice
loopback (sidetone).
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mis-typing exist in dapm controller definitions and dapm route definitions,
so happen mis-matched error when snd_soc_dapm_add_routes().
Cc: stable@kernel.org
Signed-off-by: Jinyoung Park <parkjy@mtekvision.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com
The AC97 wire format is completely fixed so CODECs don't have any choice
about the formats they accept but controllers accept a variety of data
formats and render them down onto the bus. Have a shared define so all
the CODEC drivers will interoperate with any of our controller drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.
Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On startup we try to make sure that the port is quiesced but if the
port is already stopped then this will generate a warning about the
RX/TX mode configuration. Configure the mode before doing the teardown
to suppress these warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The data format configuration for S3C64xx IISv2 is completely different
to that for S3C24xx. Instead of a single bit configuration in bit 0 of
IISMOD we have format selection in bits 13 and 14 and bit clock rate
selection in bits 1 and 2. While we're here add support for 24 bit
samples in S3C64xx.
At some point it may be desirable to expose the bit clock rate selection
to users but given the limited configuration options that may not be
required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes the interface usable with the s3c-iis-v2 rate calculator
and consistent with S3C2412.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The gain control for earpiece amplifier uses 0dB ~ 12dB according to the
TRM, but the present code is implemented to -6dB ~ 6dB.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added SNDRV_PCM_INFO_BATCH flag to PCM info field of some drivers that
really don't give the precise pointer value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to check only if the WM8350 is master and only when starting
the stream so if either is not true then we can skip the check.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a new control named 'Master Playback Switch' for cs4270
codecs. It is implemented using the new SOC_DOUBLE_EXT macro to catch
the put function and store the information about manually set mute
controls from userspace. When a manual mute is set, we don't want the
soc core to un-mute the outputs.
Renamed cs4270_mute() to cs4270_dai_mute() to avoid confusion.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The control modifies the MUTE register, hence the polarity must be
inverted.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Say what invalid values we're seeing when we see an invalid value and
ensure that errors are displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's expected behaviour for the CODEC header to provide them but the
WM8350 doesn't due to having all the registers together under drivers/mfd.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* fix/asoc:
ASoC: s3c-i2s-v2 needs to declare a license for modular builds
ASoC: remove non-existing referece to CONFIG_SND_SOC_CODEC_WM8991
ASoC: Fix WM8580 volume update handling for large register changes
ASoC: Fix offset of freqmode in WM8580 PLL configuration
The S3C64xx IIS code had a number of problems with device registration.
The hardware has two IIS ports of which the driver supported only one
at once via a single exported DAI, attempting to identify the DAI to
use based on the dev->id of the ASoC platform device. As well as
limiting the driver to only supporting one IIS port at once this also
meant that the ID of the soc-audio device (or in future the card device)
had to match the IIS ID.
Fix both problems by converting the driver to register the DAIs based on
probing of platform devices registered by the arch/arm code, using those
platform devices to interact with the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the four channel TDM mode
on Beagle board.
Depending on the channel count, the interface needs to be
configured differently (I2S for stereo DSP_A for four channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add 4 channel support to omap-mcbsp.
This mode is going to be used by the twl4030 codec, when it
is configured in Option1 mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original idea came from pHilipp, and this makes the code looks
more consistent.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSP DMA parameters can actually be easily generated at run-time since
they are almost similar except for the FIFO width and direction. Another
benefit is the re-use of information from 'struct ssp_device', like SSDR
physical FIFO address and DRCMR register index for both directions.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: pHilipp Zabel <philipp.zabel@gmail.com>
Add DAPMs for VDL(Voice Down Link) path. To support VDL path, we have
to change DAPMs of outputs(Earpiece, PreDrive Left/Right, Headset
Left/Right, Carkit Left/Right) from mux to mixer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save a little extra power by enabling the DC servo offset correction
for the output channels only when the relevant channels are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the default startup sequence in the chip to set the DC servo
dither level for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CLK_DSP provides a master clock for the DAC and ADC related functionality
on the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.
Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.
Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add checking in hw_params and prepare to detect bufferless pcms(i.e. BT
<--> codec).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add Voice DAI to support the PCM voice interface of the twl4030 codec.
The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.
The PCM voice interface has two modes
- PCM mode1 : This uses the normal FS polarity and the rising edge of
the clock signal.
- PCM mode2 : This uses the FS polarity inverted and the falling edge
of the clock signal.
If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Firstly, this patch makes the palm27x asoc driver a little more sane. Also,
since all affected devices use GPIO95 as AC97_nRESET, this patch sets that
properly. Affected are PalmT5, TX and LifeDrive.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I notice that the fixes were merged, minus one:
sound/soc/codecs/wm9705.c: At top level:
sound/soc/codecs/wm9705.c:445: warning: initialization from incompatible pointer type
so you might find this trivial patch useful.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The original implementation of the constraints were good against sane
applications.
If the opening sequence is:
stream1_open, stream1_hw_params, stream2_open, stream2_hw_params -> the
constraints are set correctly for stream2.
But if the sequence is:
stream1_open, stream2_open, stream2_hw_params, stream1_hw_params -> than stream2
would receive constraint rate = 0, sample_bits = 0, since the stream1 has not
yet called hw_params...
The command to trigger this event:
gst-launch-0.10 alsasrc device=hw:0 ! alsasink device=hw:0 sync=false
This patch does some 'black magic' in order to always set the correct
constraints and sets it only when it is needed for the other stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My email address is going to expire soon so update it. Adding also
Peter Ujfalusi <peter.ujfalusi@nokia.com> as a second contact to OMAP core
drivers since I won't have anymore access to non-public OMAP documentation
in the future and Peter is working with these drivers as well.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Those macros are just screwed as soon as CONFIG_PXA25x is enabled.
This patch
- changes ssp_set_scr to take an ssp_dev pointer instead of ssp_device
- adds a corresponding ssp_get_scr function.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DSP_A mode is similar to the DSP_B, but the MSB is delayed with
one bclk (appears after the FS pulse and not under it).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use single-phase mode for the DSP mode and keep the dual phase
mode for the I2S mode.
The mono (1 channel) mode already used single phase mode,
now it is more cleaner. There is no need to configure the
second phase, when the single phase is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using inverted FS polarity in OSK5912 must be an error since TLV320AIC23
do not have support for inverted polarities. This is mostly due the hassle
with the DSP formats in OMAP McBSP DAI and inversion on OMAP side probably
just made this configuration working at some point.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSP format wasn't still correct in OMAP McBSP DAI even after the commit
bd25867a6c.
Thanks to Peter Ujfalusi <peter.ujfalusi@nokia.com> for noticing and being
part of the fix. Now the FS length definition is more clear by defining
it with FWID(0).
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix accidental change of <mach/regs-gpio.h> to
<plat/regs-gpio.h> in s3c2412-i2s.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the build error in s3c-i2s-v2.c caused by
a change to the snd_soc_dai ops field.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The definition of s3c_i2sv2_iis_calc_rate was never
renamed from s3c2412_iis_calc_rate, so rename this
to allow the build to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build errors in sound/soc/s3c24xx/jive_wm8750.c
from changes to ASoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
pxa_ssp_set_dai_fmt() currently has an early exit if the desired format
equals the current configuration. This is correct behaviour unless this
function is called with a zero value parameter for the first time.
Zero is a valid value for this function, but the early exit is bogus in
this case.
Hence, set priv->dai_fmt to -1 in the beginning so we can configure the
port.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
