Patrick Keene wrote to the linux-dvb list, asking where in menuconfig he
can enable dvb-bt8xx for his AVerMedia DVB card. I pointed the following
out to him:
config DVB_BT8XX
tristate "Nebula/Pinnacle PCTV/Twinhan PCI cards"
It has been agreed upon that this description is extremely misleading.
This patch changes the one-liner description text of dvb-bt8xx to something
more meaningful, and adds AVerMedia to the detailed description.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IPMI power control function proc_write_chassctrl was badly written, it
directly used userspace pointers, it assumed that strings were NULL
terminated, and it used the evil sscanf function. This converts over to
using the sysctl interface for this data and changes the semantics to be a
little more logical.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes use of the previously underutilized cpuset flag
'mem_exclusive' to provide what amounts to another layer of memory placement
resolution. With this patch, there are now the following four layers of
memory placement available:
1) The whole system (interrupt and GFP_ATOMIC allocations can use this),
2) The nearest enclosing mem_exclusive cpuset (GFP_KERNEL allocations can use),
3) The current tasks cpuset (GFP_USER allocations constrained to here), and
4) Specific node placement, using mbind and set_mempolicy.
These nest - each layer is a subset (same or within) of the previous.
Layer (2) above is new, with this patch. The call used to check whether a
zone (its node, actually) is in a cpuset (in its mems_allowed, actually) is
extended to take a gfp_mask argument, and its logic is extended, in the case
that __GFP_HARDWALL is not set in the flag bits, to look up the cpuset
hierarchy for the nearest enclosing mem_exclusive cpuset, to determine if
placement is allowed. The definition of GFP_USER, which used to be identical
to GFP_KERNEL, is changed to also set the __GFP_HARDWALL bit, in the previous
cpuset_gfp_hardwall_flag patch.
GFP_ATOMIC and GFP_KERNEL allocations will stay within the current tasks
cpuset, so long as any node therein is not too tight on memory, but will
escape to the larger layer, if need be.
The intended use is to allow something like a batch manager to handle several
jobs, each job in its own cpuset, but using common kernel memory for caches
and such. Swapper and oom_kill activity is also constrained to Layer (2). A
task in or below one mem_exclusive cpuset should not cause swapping on nodes
in another non-overlapping mem_exclusive cpuset, nor provoke oom_killing of a
task in another such cpuset. Heavy use of kernel memory for i/o caching and
such by one job should not impact the memory available to jobs in other
non-overlapping mem_exclusive cpusets.
This patch enables providing hardwall, inescapable cpusets for memory
allocations of each job, while sharing kernel memory allocations between
several jobs, in an enclosing mem_exclusive cpuset.
Like Dinakar's patch earlier to enable administering sched domains using the
cpu_exclusive flag, this patch also provides a useful meaning to a cpuset flag
that had previously done nothing much useful other than restrict what cpuset
configurations were allowed.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove (or edit) remaining references to the now dead verify_area() function
from files in Documentation/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Frank Sorenson <frank@tuxrocks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since early userspace was added, there's no way to override which init to
run from it. Some people tack on an extra cpio archive with a link from
/init depending on what they want to run, but that's sometimes impractical.
Changing the "init=" to also override the early userspace isn't feasible,
since it is still used to indicate what init to run from disk when early
userspace has completed doing whatever it's doing (i.e. load filesystem
modules and drivers).
Instead, introduce "rdinit=" and make it override the default "/init" if
specified.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds the Dell Systems Management Base Driver with sysfs support.
This driver has been tested with Dell OpenManage.
Signed-off-by: Doug Warzecha <Douglas_Warzecha@dell.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Newer Sony VAIO models (VGN-S480, VGN-S460, VGN-S3XP etc) use a new method to
initialize the SPIC device. The new way to initialize (and disable) the
device comes directly from the AML code in the _CRS, _SRS and _DIS methods
from the DSDT table. This patch adds support for the new models.
Signed-off-by: Erik Waling <erikw@acc.umu.se>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All users have been converted.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Uses of RCU for dynamically changeable NMI handlers need to use the new
rcu_dereference() and rcu_assign_pointer() facilities. This change makes
it clear that these uses are safe from a memory-barrier viewpoint, but the
main purpose is to document exactly what operations are being protected by
RCU. This has been tested on x86 and x86-64, which are the only
architectures affected by this change.
Signed-off-by: <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's the latest version of relayfs, against linux-2.6.11-mm2. I'm hoping
you'll consider putting this version back into your tree - the previous
rounds of comment seem to have shaken out all the API issues and the number
of comments on the code itself have also steadily dwindled.
This patch is essentially the same as the relayfs redux part 5 patch, with
some minor changes based on reviewer comments. Thanks again to Pekka
Enberg for those. The patch size without documentation is now a little
smaller at just over 40k. Here's a detailed list of the changes:
- removed the attribute_flags in relay open and changed it to a
boolean specifying either overwrite or no-overwrite mode, and removed
everything referencing the attribute flags.
- added a check for NULL names in relayfs_create_entry()
- got rid of the unnecessary multiple labels in relay_create_buf()
- some minor simplification of relay_alloc_buf() which got rid of a
couple params
- updated the Documentation
In addition, this version (through code contained in the relay-apps tarball
linked to below, not as part of the relayfs patch) tries to make it as easy
as possible to create the cooperating kernel/user pieces of a typical and
common type of logging application, one where kernel logging is kicked off
when a user space data collection app starts and stops when the collection
app exits, with the data being automatically logged to disk in between. To
create this type of application, you basically just include a header file
(relay-app.h, included in the relay-apps tarball) in your kernel module,
define a couple of callbacks and call an initialization function, and on
the user side call a single function that sets up and continuously monitors
the buffers, and writes data to files as it becomes available. Channels
are created when the collection app is started and destroyed when it exits,
not when the kernel module is inserted, so different channel buffer sizes
can be specified for each separate run via command-line options. See the
README in the relay-apps tarball for details.
Also included in the relay-apps tarball are a couple examples
demonstrating how you can use this to create quick and dirty kernel
logging/debugging applications. They are:
- tprintk, short for 'tee printk', which temporarily puts a kprobe on
printk() and writes a duplicate stream of printk output to a relayfs
channel. This could be used anywhere there's printk() debugging code
in the kernel which you'd like to exercise, but would rather not have
your system logs cluttered with debugging junk. You'd probably want
to kill klogd while you do this, otherwise there wouldn't be much
point (since putting a kprobe on printk() doesn't change the output
of printk()). I've used this method to temporarily divert the packet
logging output of the iptables LOG target from the system logs to
relayfs files instead, for instance.
- klog, which just provides a printk-like formatted logging function
on top of relayfs. Again, you can use this to keep stuff out of your
system logs if used in place of printk.
The example applications can be found here:
http://prdownloads.sourceforge.net/dprobes/relay-apps.tar.gz?download
From: Christoph Hellwig <hch@lst.de>
avoid lookup_hash usage in relayfs
Signed-off-by: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates documentation a bit (mostly removing obsolete stuff), and
marks swsusp as no longer experimental in config.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change filemode to use defines in stead of 0644,
based on suggestions by Walter Harms and Domen Puncer.
Signed-off-by: Jan Veldeman <Jan.Veldeman@advalvas.be>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix whitespace after comma between parameters.
Signed-off-by: Jan Veldeman <Jan.Veldeman@advalvas.be>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 24RF08 corruption would better be prevented at i2c-core level than
at chip driver level, for several reasons:
* The second quick write should happen as soon as possible after the
first one, so as to limit the risk that another command is issued on
the bus inbetween, causing the corruption.
* As a matter of fact, the protection code at driver level was reworked
at least three times already, which proves how hard it is to get it
right there, while it's straightforward at i2c-core level.
* It's easy to add a new driver that would need the protection, and
forget to add it. This did happen already.
* As additional probing addresses can be passed to most i2c chip drivers
as module parameters, virtually every i2c chip driver would need the
protection if we want to be really safe.
* Why duplicate code when we can easily avoid it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe was quite complex and slow, so I rewrote it in a more
efficient and hopefully clearer way.
Note that this slightly changes the way the module parameters are
handled. This shouldn't change anything for the most common cases
though.
For one thing, the function now respects the order of the parameters
for address probing. It used to always do lower addresses first. The
new approach gives the user more control.
For another, ignore addresses don't overrule probe addresses anymore.
This could have been restored the way it was at the cost of a few more
lines of code, but I don't think it's worth it. Both lists are given
as module parameters, so a user would be quite silly to specify the
same addresses in both lists. The normal addresses list is the only
one that isn't controlled by a module parameter, thus is the only one
the user may reasonably want to remove an address from.
Another significant change is the fact that i2c_probe() will no more
stop when a detection function returns -ENODEV. Just because a driver
found a chip it doesn't support isn't a valid reason to stop all
probings for this one driver. This closes the long standing lm_sensors
ticket #1807.
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1807
I updated the documentation accordingly.
In terms of algorithmic complexity, the new code is way better. If
I is the ignore address count, P the probe address count, N the
normal address count and F the force address count, the old code
was doing 128 * (F + I + P + N) iterations max, while the new code
does F + P + ((I+1) * N) iterations max. For the most common case
where F, I and P are empty, this is down from 128 * N to N.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a typo in the i2c documentation: the i2c bus scanning tool found in
lm_sensors is called i2cdetect, not i2c_detect.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds documentation entry for W83792D chip.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill all uses of i2c_is_isa_adapter except for the hybrid drivers (it87,
lm78, w83781d). The i2c-isa adapter not being registered with the i2c
core anymore, drivers don't have to fear being erroneously attached to
it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.
normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the separate client name for the LM78-J chip. This is really
only a later revision of the LM78, with almost no difference and
no difference the driver handles in any case.
This was the only client name that had a dash in it, and special care
had to be taken in libsensors because of it. As we plan to write a new
library soon, I'd like to get rid of this exception before we do.
As a nice side effect, it saves 876 bytes in lm78.ko.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updates to the max6875 driver documentation.
This brings the documentation in sync with the code, which was recently
simplified.
This patch is based off 2.6.13-rc2-mm2.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch contains a mini howto for using dm-crypt together with
swsusp.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PowerPC 40x and Book-E processors support a watchdog timer at the processor
core level. The timer has implementation dependent timeout frequencies
that can be configured by software.
One the first Watchdog timeout we get a critical exception. It is left to
board specific code to determine what should happen at this point. If
nothing is done and another timeout period expires the processor may
attempt to reset the machine.
Command line parameters:
wdt=0 : disable watchdog (default)
wdt=1 : enable watchdog
wdt_period=N : N sets the value of the Watchdog Timer Period.
The Watchdog Timer Period meaning is implementation specific. Check
User Manual for the processor for more details.
This patch is based off of work done by Takeharu Kato.
Signed-off-by: Matt McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a "smaps" entry to /proc/pid: show howmuch memory is resident in each
mapping.
People that want to perform a memory consumption analysing can use it
mainly if someone needs to figure out which libraries can be reduced for
embedded systems. So the new features are the physical size of shared and
clean [or dirty]; private and clean [or dirty].
Take a look the example below:
# cat /proc/4576/smaps
08048000-080dc000 r-xp /bin/bash
Size: 592 KB
Rss: 500 KB
Shared_Clean: 500 KB
Shared_Dirty: 0 KB
Private_Clean: 0 KB
Private_Dirty: 0 KB
080dc000-080e2000 rw-p /bin/bash
Size: 24 KB
Rss: 24 KB
Shared_Clean: 0 KB
Shared_Dirty: 0 KB
Private_Clean: 0 KB
Private_Dirty: 24 KB
080e2000-08116000 rw-p
Size: 208 KB
Rss: 208 KB
Shared_Clean: 0 KB
Shared_Dirty: 0 KB
Private_Clean: 0 KB
Private_Dirty: 208 KB
b7e2b000-b7e34000 r-xp /lib/tls/libnss_files-2.3.2.so
Size: 36 KB
Rss: 12 KB
Shared_Clean: 12 KB
Shared_Dirty: 0 KB
Private_Clean: 0 KB
Private_Dirty: 0 KB
...
(Includes a cleanup from "Richard Purdie" <rpurdie@rpsys.net>)
From: Torsten Foertsch <torsten.foertsch@gmx.net>
show_smap calls first show_map and then prints its additional information to
the seq_file. show_map checks if all it has to print fits into the buffer and
if yes marks the current vma as written. While that is correct for show_map
it is not for show_smap. Here the vma should be marked as written only after
the additional information is also written.
The attached patch cures the problem. It moves the functionality of the
show_map function to a new function show_map_internal that is called with an
additional struct mem_size_stats* argument. Then show_map calls
show_map_internal with NULL as struct mem_size_stats* whereas show_smap calls
it with a real pointer. Now the final
if (m->count < m->size) /* vma is copied successfully */
m->version = (vma != get_gate_vma(task))? vma->vm_start: 0;
is done only if the whole entry fits into the buffer.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The idea of a swap_device_lock per device, and a swap_list_lock over them all,
is appealing; but in practice almost every holder of swap_device_lock must
already hold swap_list_lock, which defeats the purpose of the split.
The only exceptions have been swap_duplicate, valid_swaphandles and an
untrodden path in try_to_unuse (plus a few places added in this series).
valid_swaphandles doesn't show up high in profiles, but swap_duplicate does
demand attention. However, with the hold time in get_swap_pages so much
reduced, I've not yet found a load and set of swap device priorities to show
even swap_duplicate benefitting from the split. Certainly the split is mere
overhead in the common case of a single swap device.
So, replace swap_list_lock and swap_device_lock by spinlock_t swap_lock
(generally we seem to prefer an _ in the name, and not hide in a macro).
If someone can show a regression in swap_duplicate, then probably we should
add a hashlock for the swap_map entries alone (shorts being anatomic), so as
to help the case of the single swap device too.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the feature is removed, there's no need to keep the entry in
feature-removal-schedule.txt.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The XTEA implementation was incorrect due to a misinterpretation of
operator precedence. Because of the wide-spread nature of this
error, the erroneous implementation will be kept, albeit under the
new name of XETA.
Signed-off-by: Aaron Grothe <ajgrothe@yahoo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)
There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive. In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.
There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.
Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
