To start with, arch_notes_size() etc. is a little too ambiguous a name for
my liking, so change the function names to be more explicit.
Calling through macros is ugly, especially with hidden parameters, so don't
do that, call the routines directly.
Use ARCH_HAVE_EXTRA_ELF_NOTES as the only flag, and based on it decide
whether we want the extern declarations or the empty versions.
Since we have empty routines, actually use them in the coredump code to
save a few #ifdefs.
We want to change the handling of foffset so that the write routine updates
foffset as it goes, instead of using file->f_pos (so that writing to a pipe
works). So pass foffset to the write routine, and for now just set it to
file->f_pos at the end of writing.
It should also be possible for the write routine to fail, so change it to
return int and treat a non-zero return as failure.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because spufs might be built as a module, we can't have other parts of the
kernel calling directly into it, we need stub routines that check first if the
module is loaded.
Currently we have two structures which hold callbacks for these stubs, the
syscalls are in spufs_calls and the coredump calls are in spufs_coredump_calls.
In both cases the logic for registering/unregistering is essentially the same,
so we can simplify things by combining the two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spu_create and spu_run are wrapped by the cell syscall layer, so
we don't need the asmlinkage.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, a built-in spufs will not use the spufs_calls callbacks, but
directly call sys_spu_create. This saves us an indirect branch, but
means we have duplicated functions - one for CONFIG_SPU_FS=y and one for
=m.
This change unifies the spufs syscall path, and provides access to the
spufs_calls structure through a get/put pair. At present, the only user
of the spufs_calls structure is spu_syscalls.c, but this will facilitate
adding the coredump calls later.
Everyone likes numbers, right? Here's a before/after comparison with
CONFIG_SPU_FS=y, doing spu_create(); close(); 64k times.
Before:
[jk@cell ~]$ time ./spu_create
performing 65536 spu_create calls
real 0m24.075s
user 0m0.146s
sys 0m23.925s
After:
[jk@cell ~]$ time ./spu_create
performing 65536 spu_create calls
real 0m24.777s
user 0m0.141s
sys 0m24.631s
So, we're adding around 11us per syscall, at the benefit of having
only one syscall path.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current status of APUS:
- arch/powerpc/: removed in 2.6.23
- arch/ppc/: marked BROKEN since 2 years
This therefore removes the remaining parts of APUS support from
arch/ppc, include/asm-ppc, arch/powerpc and include/asm-powerpc.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current definition of struct ccsr_guts in immap_86xx.h was for 85xx.
This patch fixes that and replaces the vague integer types with sized types
of the correct endianness. The unused struct ccsr_pci is also deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the clrsetbits_xxx() macros, which are used to set and clear
multiple bits in a single read-modify-write operation. Specify the bits to
clear in the 'clear' parameter and the bits to set in the 'set' parameter.
These macros can also be used to set a multiple-bit bit pattern using a mask,
by specifying the mask in the 'clear' parameter and the new bit pattern in the
'set' parameter. There are big-endian and little-endian versions for 8, 16,
32, and 64 bits.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to configure and control QE pario pins from the kernel.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These I/O accessors will be used in code under drivers/,
which is expected to still work in arch/ppc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We get warnings like the following from the various ppc32 head*.S files:
WARNING: vmlinux.o(.text+0x358): Section mismatch: reference to .init.text:early_init (between 'skpinv' and 'interrupt_base')
WARNING: vmlinux.o(.text+0x380): Section mismatch: reference to .init.text:machine_init (between 'skpinv' and 'interrupt_base')
WARNING: vmlinux.o(.text+0x384): Section mismatch: reference to .init.text:MMU_init (between 'skpinv' and 'interrupt_base')
WARNING: vmlinux.o(.text+0x3aa): Section mismatch: reference to .init.text:start_kernel (between 'skpinv' and 'interrupt_base')
WARNING: vmlinux.o(.text+0x3ae): Section mismatch: reference to .init.text:start_kernel (between 'skpinv' and 'interrupt_base')
Added a .text.head section simliar to what other architectures do since
modpost already excludes this from its warnings.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so that SPE support can be determined at runtime. This is similiar
to how we handle AltiVec. This allows us to have SPE support built in and
work on processors with and without SPE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added basic board port for MPC8572 DS reference platform that is
similiar to the MPC8544/33 DS reference platform in uniprocessor mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new error codes that may be returned by the LV1 hypervisor
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some versions of PWRficient 1682M have an interrupt controller in which
the first register in each pair for interrupt sources doesn't always
read with the right polarity/sense values.
To work around this, keep a software copy of the register instead. Since
it's not modified from the mpic itself, it's a feasible solution. Still,
keep it under a config option to avoid wasting memory on other platforms.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's no need to call the runlatch on functions on processors that
don't implement them (CPU_FTR_CTRL).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export some of the implementation-specific registers via sysfs.
Useful when debugging, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The majority of irq_host implementations (3 out of 4) are associated
with a device_node, and need to stash it somewhere. Rather than having
it somewhere different for each host, add an optional device_node pointer
to the irq_host structure.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit f629307c85 introduced uses of
kernel_termios_to_user_termios_1 and user_termios_to_kernel_termios_1
on all architectures. However, powerpc, s390, avr32 and frv don't
currently define those functions since their termios struct didn't
need to be changed when the arbitrary baud rate stuff was added, and
thus the kernel won't currently build on those architectures.
This adds definitions of kernel_termios_to_user_termios_1 and
user_termios_to_kernel_termios_1 to include/asm-generic/termios.h
which are identical to kernel_termios_to_user_termios and
user_termios_to_kernel_termios respectively. The definitions are the
same because the "old" termios and "new" termios are in fact the same
on these architectures (which are the same ones that use
asm-generic/termios.h).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Taneli Vähäkangas <vahakang@cs.helsinki.fi> reported that commit
786d7e1612 aka "Fix rmmod/read/write races
in /proc entries" broke SBCL + SLIME combo.
The old code in do_select() used DEFAULT_POLLMASK, if couldn't find
->poll handler. The new code makes ->poll always there and returns 0 by
default, which is not correct. Return DEFAULT_POLLMASK instead.
Steps to reproduce:
install emacs, SBCL, SLIME
emacs
M-x slime in *inferior-lisp* buffer
[watch it doing "Connecting to Swank on port X.."]
Please, apply before 2.6.23.
P.S.: why SBCL can't just read(2) /proc/cpuinfo is a mystery.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: T Taneli Vahakangas <vahakang@cs.helsinki.fi>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AdvanSys driver wants to align some pointers, and the ALIGN macro
doesn't work for pointers. Rather than try to make it work, add a new
PTR_ALIGN macro which is typesafe.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch has added #include <linux/spinlock.h> to include/linux/leds.h
for rwlock_t.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: irq and pci_ids patch for Intel Tolapai
PCI: unhide SMBus on Compaq Deskpro EP 401963-001 motherboard
PCI: Remove __devinit from pcibios_get_irq_routing_table
PCI: remove devinit from pci_read_bridge_bases
PCI AER: fix warnings when PCIEAER=n
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[INET_DIAG]: Fix oops in netlink_rcv_skb
[IPv6]: Fix NULL pointer dereference in ip6_flush_pending_frames
[NETFILTER]: Fix/improve deadlock condition on module removal netfilter
[NETFILTER]: nf_conntrack_ipv4: fix "Frag of proto ..." messages
[NET] DOC: Update networking/multiqueue.txt with correct information.
[IPV6]: Freeing alive inet6 address
[DECNET]: Fix interface address listing regression.
[IPV4] devinet: show all addresses assigned to interface
[NET]: Do not dereference iov if length is zero
[TG3]: Workaround MSI bug on 5714/5780.
[Bluetooth] Fix parameter list for event filter command
[Bluetooth] Update security filter for Bluetooth 2.1
[Bluetooth] Add compat handling for timestamp structure
[Bluetooth] Add missing stat.byte_rx counter modification
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] libiscsi: sync up iscsi and scsi eh's access to the connection
[SCSI] libiscsi: fix null ptr regression when aborting a command with data to transfer
[SCSI] qla2xxx: Update version number to 8.02.00-k3.
[SCSI] qla2xxx: Correct mailbox register dump for FWI2 capable ISPs.
[SCSI] qla2xxx: Correct 8GB iIDMA support.
[SCSI] qla2xxx: Correct management-server login-state synchronization issue.
[SCSI] qla2xxx: Don't modify parity bits during ISP25XX restart.
[SCSI] qla2xxx: Allocate enough space for the full PCI descriptor.
[SCSI] zfcp: fix the data buffer accessor patch
[SCSI] zfcp: allocate gid_pn_data objects from gid_pn_cache
[SCSI] zfcp: fix memory leak
This patch adds the Intel Tolapai LPC and SMBus Controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix warnings when CONFIG_PCIEAER=n:
drivers/pci/pcie/portdrv_pci.c:105: warning: statement with no effect
drivers/pci/pcie/portdrv_pci.c:226: warning: statement with no effect
drivers/scsi/arcmsr/arcmsr_hba.c:352: warning: statement with no effect
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So I've had a deadlock reported to me. I've found that the sequence of
events goes like this:
1) process A (modprobe) runs to remove ip_tables.ko
2) process B (iptables-restore) runs and calls setsockopt on a netfilter socket,
increasing the ip_tables socket_ops use count
3) process A acquires a file lock on the file ip_tables.ko, calls remove_module
in the kernel, which in turn executes the ip_tables module cleanup routine,
which calls nf_unregister_sockopt
4) nf_unregister_sockopt, seeing that the use count is non-zero, puts the
calling process into uninterruptible sleep, expecting the process using the
socket option code to wake it up when it exits the kernel
4) the user of the socket option code (process B) in do_ipt_get_ctl, calls
ipt_find_table_lock, which in this case calls request_module to load
ip_tables_nat.ko
5) request_module forks a copy of modprobe (process C) to load the module and
blocks until modprobe exits.
6) Process C. forked by request_module process the dependencies of
ip_tables_nat.ko, of which ip_tables.ko is one.
7) Process C attempts to lock the request module and all its dependencies, it
blocks when it attempts to lock ip_tables.ko (which was previously locked in
step 3)
Theres not really any great permanent solution to this that I can see, but I've
developed a two part solution that corrects the problem
Part 1) Modifies the nf_sockopt registration code so that, instead of using a
use counter internal to the nf_sockopt_ops structure, we instead use a pointer
to the registering modules owner to do module reference counting when nf_sockopt
calls a modules set/get routine. This prevents the deadlock by preventing set 4
from happening.
Part 2) Enhances the modprobe utilty so that by default it preforms non-blocking
remove operations (the same way rmmod does), and add an option to explicity
request blocking operation. So if you select blocking operation in modprobe you
can still cause the above deadlock, but only if you explicity try (and since
root can do any old stupid thing it would like.... :) ).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata clear horkage on ata_dev_init()
[libata, IDE] add new VIA bridge to VIA PATA drivers
pata_it821x: fix lost interrupt with atapi devices
Fix broken pata_via cable detection
The earlier crash dump fix on x86_64 depended on patches in -mm which
are intended for post-2.6.23. Without those, it broke the build when
it went into 2.6.23-rc5.
This changes the field references in ELF_CORE_COPY_REGS back to those
still used in mainline.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Ocelot: remove remaining bits
[MIPS] TLB: Fix instruction bitmasks
[MIPS] R10000: Fix wrong test in dma-default.c
[MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
[MIPS] Sibyte: Remove broken dependency on EXPERIMENTAL from SIBYTE_SB1xxx_SOC.
[MIPS] Kconfig: whitespace cleanup.
[MIPS] PCI: Set need_domain_info if controller domain index is non-zero.
[MIPS] BCM1480: Fix computation of interrupt mask address register.
[MIPS] i8259: Add disable method.
[MIPS] tty: add the new ioctls and definitions.
Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()
[...]
on_each_cpu(do_drain, cachep, 1, 1);
check_irq_on();
[...]
may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting
in a back-to-back hazard.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Same as all the others, just put in the constants for the existing kernel
code and termios2 structure
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Cell BE Architecture spec states that the SPU MFC Class 0 interrupt
is edge-triggered. The current spu interrupt handler assumes this
behavior and does not clear the interrupt status.
The PS3 hypervisor visualizes all SPU interrupts as level, and on return
from the interrupt handler the hypervisor will deliver a new virtual
interrupt for any unmasked interrupts which for which the status has not
been cleared. This fix clears the interrupt status in the interrupt
handler.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The names of STI and CLI macros were derived from i386 arch historically,
but their name are incomprehensible.
So, for easy to understand, rename these macros to ENABLE_INTERRUPTS
and DISABLE_INTERRUPTS, respectively.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Some braille keyboards have 10 dots, so extend the Input braille keys
definitions.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some m32r platforms, cascaded ICUs are used.
This patch is required to simplify ei_handler and consolidate platform-
dependent ICU check routines.
platform ICU/INT1 ICU/INT0 ICU/INT2
-------------- -------- -------- --------
m32104ut o - -
m32700ut o o o
opsput o o o
usrv o - -
(others) - - -
Signed-off-by: Hitoshi Yamamoto <hitoshiy@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Ryusuke Konishi says:
The recent truncate_complete_page() clears the dirty flag from a page
before calling a_ops->invalidatepage(),
^^^^^^
static void
truncate_complete_page(struct address_space *mapping, struct page *page)
{
...
cancel_dirty_page(page, PAGE_CACHE_SIZE); <--- Inserted here at
kernel 2.6.20
if (PagePrivate(page))
do_invalidatepage(page, 0); ---> will call
a_ops->invalidatepage()
...
}
and this is disturbing nfs_wb_page_priority() from calling
nfs_writepage_locked() that is expected to handle the pending
request (=nfs_page) associated with the page.
int nfs_wb_page_priority(struct inode *inode, struct page *page, int how)
{
...
if (clear_page_dirty_for_io(page)) {
ret = nfs_writepage_locked(page, &wbc);
if (ret < 0)
goto out;
}
...
}
Since truncate_complete_page() will get rid of the page after
a_ops->invalidatepage() returns, the request (=nfs_page) associated
with the page becomes a garbage in nfs_inode->nfs_page_tree.
------------------------
Fix this by ensuring that nfs_wb_page_priority() recognises that it may
also need to clear out non-dirty pages that have an nfs_page associated
with them.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
After my last patch we have a new header file for HP simulator use.
Here's code to use it for stuff that used to have `extern' statements
inline in the code. Functionality should not change with this patch.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
