Specify sr4 when flushing kernel space (we could equally well use sr5-7,
but must not use sr0).
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
replace use of "0" with "%r0" since PA 1.1 I/D flush ops only take a
general register and not an immediate value for the index field.
This just forces the code to always be PA 1.1 "clean".
From: Joel Soete <soete.joel@tiscali.be>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc2-pa3 fix copy_user_page_asm to NOT access past end of page.
My bad. /o\
Lamont confirmed that instructions following a conditional
branch are *alway* executed regardless if the branch is taken or not.
Unless they are nullified (which was missing in this case).
He also noted:
Conditional branches nullify on forward taken branch, and on
non-taken backward branch. Note that .+4 is a backwards branch.
This makes alot more sense than the giberish in the PA20 arch book.
Compiles and boots on both 64-bit (a500) and 32-bit (j6k).
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
remove the spurious do_softirq calls from entry.S
With these in we were calling do_softirq twice; plus the calls in
entry.S took no account of nesting.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix the alloc_slabmgmt panic
Hopefully this should also fix a lot of other intermittent kernel bugs.
The problem has been around since 2.6.9-rc2-pa6 when we allowed
floating point registers to be used in kernel code. The essence of
the problem is that gcc prefers to use floating point for integer
divides and multiples. Further, it can rely on the values in the no
clobber fp regs being correct across a function call. Unfortunately,
our task switch function only saves the integer no clobber registers,
not the fp ones, so if gcc makes a function call to any function in
the kernel which could sleep, the values it is relying on in any no
clobber floating point register may be lost. In the case of
alloc_slabmgmt, the value of the page offset is being stored in %fr12
across a call to kmem_getpages(), which sleeps if no pages are
available. Thus, the offset can be trashed and the slab code can end
up with a completely bogus address leading to corruption.
Kudos to Randolph who came up with the program to trip this problem at
will and thus allowed it to be tracked and fixed.
Signed-off-by: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* arch/parisc/kernel/process.c (sys_clone): Use 5 args, and process
CLONE_PARENT_SETTID, CLONE_CHILD_SETTID, CLONE_CHILD_CLEARTID.
(copy_thread): First cut at CLONE_SETTLS.
Signed-off-by: Carlos O'Donell <carlos@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.14-rc2-pa1: enable 100/250/1000HZ itimer selection
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Mark floppy as broken. Thanks Joel
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
make DISCONTIGMEM depend on 64BIT
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Prefix changed in debian, include "gnu" in the commandline.
Signed-off-by: Carlos O'Donell <carlos@parisc-linux.org>
Ensure the compiler version is new enough (>= 3.3)
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Document history of PDC_NARROW a bit as it will still show
up in an older kernel's .config file.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Generate a more informative message when a resource does not have
a parent.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Get rid of some unnecessary includes
Remove a layer of macro indirection around pdc_console_device
Delete pdc_console_die() as it is unused
Avoid double-printing on panic by clearing CON_PRINTBUFFER rather than
setting con_start to be log_end
Make con_start and log_end static again
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.13-rc6-pa2
use force_sigsegv() if we have a problem setting up a frame. This is
required to prevent SIGSEGV loops.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
We're using fp regs now in the kernel, so we want to print them
on stack dump
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Disable use of fpregs in pa_memcpy, and turn on the
-mdisable-fpregs flag.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
PA20 arch book (page 7-52 and 7-55) indicate a "sync" is required after
the FDC "to enforce instruction ordering". And we want to make
sure FIC is executed after FDC has retired.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc1-pa6 use work queue in LED/LCD driver instead of tasklet.
Main advantage is it allows use of msleep() in the led_LCD_driver to
"atomically" perform two MMIO writes (CMD, then DATA).
Lead to nice cleanup of the main led_work_func() and led_LCD_driver().
Kudos to David for being persistent.
From: David Pye <dmp@davidmpye.dyndns.org>
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
update comment about CAFL_STRIDE
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fixed a bug in parisc_setup_cache_timing() which caused it to calculate
a poor value for parisc_cache_flush_threshold.
Thanks to Joel Soete for spotting the bug.
Thanks to James Bottomley for pointing out the clean way to fix this.
Signed-off-by: Stuart Brady <sdb@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
convert some bl calls to b,l or bv to use longer offsets
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
export profile_pc() symbol - oprofile needs it when built as a module.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Take into account nullified insn and lock functions for profiling
This is needed at the end of functions; it is typical that the return
branch nullifies the next insn, which is in the next function. This
causes profiling data to show up against the "wrong" function.
We also count lock times against the locker. This is consistent with
other architectures.
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
2.6.12-rc4-pa3 : first pass at making sure use of RFI conforms to
PA 2.0 arch pages F-4 and F-5, PA 1.1 Arch page 3-19 and 3-20.
The discussion revolves around all the rules for clearing PSW Q-bit.
The hard part is meeting all the rules for "relied upon translation".
.align directive is used to guarantee the critical sequence ends more than
8 instructions (32 bytes) from the end of page.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix parse_tree_node. much more needs to be done to fix this file.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Make drivers.c compile based on a patch from Pat Mochel.
From: Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix drivers.c to create new device tree nodes when no match is found.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Do a proper depth-first search returning parents before children, using the
new klist infrastructure.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Fixed parisc_device traversal so that pdc_stable works again
Fixed check_dev so it doesn't dereference a parisc_device until it
has verified the bus type
Signed-off-by: Randolph Chung <tausq@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Use insert_resource() instead of request_mem_region().
Request resources at bus walk time instead of driver probe time.
Don't release the resources as we don't have any hotplug parisc_device
support yet.
Add parisc_pathname() to conveniently get the textual representation
of the hwpath used in sysfs.
Inline the remnants of claim_device() into its caller.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
I noticed that some of the STI regions weren't showing up in iomem.
Reading the STI spec indicated that all STI devices occupy at least 32MB.
So check for STI HPAs and give them 32MB instead of 4kB.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Not sure how it slipped by, but here's a trivial typo fix for powernow.
Signed-off-by: Chris Wright <chrisw@osdl.org>
[ It's "nurter" backwards.. Maybe we have a hillbilly The Shining fan? ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD recently discovered that on some hardware, there is a race condition
possible when a C-state change request goes onto the bus at the same
time as a P-state change request.
Both requests happen, but the southbridge hardware only acknowledges the
C-state change. The PowerNow! driver is then stuck in a loop, waiting
for the P-state change acknowledgement. The driver eventually times
out, but can no longer perform P-state changes.
It turns out the solution is to resend the P-state change, which the
southbridge will acknowledge normally.
Thanks to Johannes Winkelmann for reporting this and testing the fix.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a stupid typo bug in the iSeries hash table code.
When we place a hash PTE in the secondary bucket, instead of setting the
SECONDARY flag bit, as we should, we (redundantly) set the VALID flag.
This was introduced with the patch abolishing bitfields from the hash
table code. Mea culpa, oops. It hasn't been noticed until now because
in practice we don't hit the secondary bucket terribly often.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While working on 64K pages, I found this little buglet in our
update_mmu_cache() implementation.
The code calls __hash_page() passing it an "access" parameter (the type
of access that triggers the hash) containing the bits _PAGE_RW and
_PAGE_USER of the linux PTE. The latter is useless in this case and the
former is wrong. In fact, if we have a writeable PTE and we pass
_PAGE_RW to hash_page(), it will set _PAGE_DIRTY (since we track dirty
that way, by hash faulting !dirty) which is not what we want.
In fact, the correct fix is to always pass 0. That means that only
read-only or already dirty read write PTEs will be preloaded. The
(hopefully rare) case of a non dirty read write PTE can't be preloaded
this way, it will have to fault in hash_page on the actual access.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes a typo in the div128_by_32 function used in the timekeeping
calculations on ppc64. If you look at the code it's quite obvious
that we need (rb + c) rather than (rb + b). The "b" is clearly just a
typo.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
The current Simtec BAST nand area timings are a little
too slow to be obtained by a 2410 running at 266MHz,
so reduce the timings slightly to bring them into the
acceptable range.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Matt Reimer
Adds an I2S platform_device for PXA. I2S is used to interface
with sound chips on systems like iPAQ h1910/h2200/hx4700 and
Asus 716.
Signed-off-by: mreimer@vpop.net
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Missing half of the [PATCH] uml: Fix sysrq-r support for skas mode
We need to remove these (UPT_[DEFG]S) from the read side as well as the
write one - otherwise it simply won't build.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This introduces a limit parameter to the core bootmem allocator; The new
parameter indicates that physical memory allocated by the bootmem
allocator should be within the requested limit.
We also introduce alloc_bootmem_low_pages_limit, alloc_bootmem_node_limit,
alloc_bootmem_low_pages_node_limit apis, but alloc_bootmem_low_pages_limit
is the only api used for swiotlb.
The existing alloc_bootmem_low_pages() api could instead have been
changed and made to pass right limit to the core allocator. But that
would make the patch more intrusive for 2.6.14, as other arches use
alloc_bootmem_low_pages(). We may be done that post 2.6.14 as a
cleanup.
With this, swiotlb gets memory within 4G for both x86_64 and ia64
arches.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The implementation of __kernel_gettimeofday() in the 32 bits vDSO has a
small bug (a typo actually) that will cause it to lose 1 bit of precision.
Not terribly bad but worth fixing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Tony Lindgren
Machine restart calls cpu_proc_fin() to clean and disable
cache, and turn off interrupts. This patch adds proper
cpu_v6_proc_fin.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Check that the device we are looking at is really
a platform device before trying to cast it to one
to find out the platform bus number.
Thanks to RMK for pointing this out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andreas Schwab spotted that recent kernels broke reporting of the PowerMac
machine model in /proc/cpuinfo. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes the following BUG message of arch/m32r/smp.c for
CONFIG_DEBUG_PREEMPT:
BUG: using smp_processor_id() in preemptible
This message is displayed by an smp_processor_id() execution during
kernel's preemptible-state.
Signed-off-by: Hitoshi Yamamoto <hitoshiy@isl.melco.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/mips/pci/fixup-tb0226.c: In function `pcibios_map_irq':
arch/mips/pci/fixup-tb0226.c:31: warning: implicit declaration of function `vr41xx_set_irq_trigger'
arch/mips/pci/fixup-tb0226.c:32: error: `TRIGGER_LEVEL' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:32: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-tb0226.c:32: error: for each function it appears in.)
arch/mips/pci/fixup-tb0226.c:33: error: `SIGNAL_THROUGH' undeclared (first use in this function)
arch/mips/pci/fixup-tb0226.c:34: warning: implicit declaration of function `vr41xx_set_irq_level'
arch/mips/pci/fixup-tb0226.c:34: error: `LEVEL_LOW' undeclared (first use in this function)
Signed-off-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doing a "SUNW,stop-self" firmware call on the other cpus is not the
correct thing to do when dropping into the firmware for a halt,
reboot, or power-off.
For now, just do nothing to quiet the other cpus, as the system should
be quiescent enough. Later we may decide to implement smp_send_stop()
like the other SMP platforms do.
Based upon a report from Christopher Zimmermann.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Richard Purdie
Remove a couple of lines of accidently added code causing compile
errors.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
