An Agere FW643 OHCI 1.1 card works fine for video reception from one
camera but fails early if receiving from two cameras. After a short
while, no IR IRQ events occur and the context control register does not
react anymore. This happens regardless whether both IR DMA contexts are
dual-buffer or one is dual-buffer and the other packet-per-buffer.
This can be worked around by disabling dual buffer DMA mode entirely.
http://sourceforge.net/mailarchive/message.php?msg_name=4A7C0594.2020208%40gmail.com
(Reported by Samuel Audet.)
In another report (by Jonathan Cameron), an FW643 works OK with two
cameras in dual buffer mode. Whether this is due to different chip
revisions or different usage patterns (different video formats) is not
yet clear. However, as far as the current capabilities of
firewire-core's isochronous I/O interface are concerned, simply
switching off dual-buffer on non-working and working FW643s alike is not
a problem in practice. We only need to revisit this issue if we are
going to enhance the interface, e.g. so that applications can explicitly
choose modes.
Reported-by: Samuel Audet <samuel.audet@gmail.com>
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This fixes a regression due to post 2.6.30 commit "firewire: core: do
not DMA-map stack addresses" 6fdc037094.
As David Moore noted, a previously correct sizeof() expression became
wrong since the commit changed its argument from an array to a pointer.
This resulted in an oops in ohci_cancel_packet in the shared workqueue
thread's context when an isochronous resource was to be freed.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bug introduced by mainline commit e7432675f8
The bug causes ocfs2_write_begin_nolock() to oops when len=0.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Fix some problems seen in the chunk size processing when activating a
pre-existing snapshot.
For a new snapshot, the chunk size can either be supplied by the creator
or a default value can be used. For an existing snapshot, the
chunk size in the snapshot header on disk should always be used.
If someone attempts to load an existing snapshot and has the 'default
chunk size' option set, the kernel uses its default value even when it
is incorrect for the snapshot being loaded. This patch ensures the
correct on-disk value is always used.
Secondly, when the code does use the chunk size stored on the disk it is
prudent to revalidate it, so the code can exit cleanly if it got
corrupted as happened in
https://bugzilla.redhat.com/show_bug.cgi?id=461506 .
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Break the function set_chunk_size to two functions in preparation for
the fix in the following patch.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If a persistent snapshot fills up, a race can corrupt the on-disk header
which causes a crash on any future attempt to activate the snapshot
(typically while booting). This patch fixes the race.
When the snapshot overflows, __invalidate_snapshot is called, which calls
snapshot store method drop_snapshot. It goes to persistent_drop_snapshot that
calls write_header. write_header constructs the new header in the "area"
location.
Concurrently, an existing kcopyd job may finish, call copy_callback
and commit_exception method, that goes to persistent_commit_exception.
persistent_commit_exception doesn't do locking, relying on the fact that
callbacks are single-threaded, but it can race with snapshot invalidation and
overwrite the header that is just being written while the snapshot is being
invalidated.
The result of this race is a corrupted header being written that can
lead to a crash on further reactivation (if chunk_size is zero in the
corrupted header).
The fix is to use separate memory areas for each.
See the bug: https://bugzilla.redhat.com/show_bug.cgi?id=461506
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Refactor chunk_io to prepare for the fix in the following patch.
Pass an area pointer to chunk_io and simplify zero_disk_area to use
chunk_io. No functional change.
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Device-mapper userspace logs (like the clustered log) are
identified by a universally unique identifier (UUID). This
identifier is used to associate requests from the kernel to
a specific log in userspace. The UUID must be unique everywhere,
since multiple machines may use this identifier when communicating
about a particular log, as is the case for cluster logs.
Sometimes, device-mapper/LVM may re-use a UUID. This is the
case during pvmoves, when moving from one segment of an LV
to another, or when resizing a mirror, etc. In these cases,
a new log is created with the same UUID and loaded in the
"inactive" slot. When a device-mapper "resume" is issued,
the "live" table is deactivated and the new "inactive" table
becomes "live". (The "inactive" table can also be removed
via a device-mapper 'clear' command.)
The above two issues were colliding. More than one log was being
created with the same UUID, and there was no way to distinguish
between them. So, sometimes the wrong log would be swapped
out during the exchange.
The solution is to create a locally unique identifier,
'luid', to go along with the UUID. This new identifier is used
to determine exactly which log is being referenced by the kernel
when the log exchange is made. The identifier is not
universally safe, but it does not need to be, since
create/destroy/suspend/resume operations are bound to a specific
machine; and these are the operations that make up the exchange.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a bug which was triggering a case where the primary leg
could not be changed on failure even when the mirror was in-sync.
The case involves the failure of the primary device along with
the transient failure of the log device. The problem is that
bios can be put on the 'failures' list (due to log failure)
before 'fail_mirror' is called due to the primary device failure.
Normally, this is fine, but if the log device failure is transient,
a subsequent iteration of the work thread, 'do_mirror', will
reset 'log_failure'. The 'do_failures' function then resets
the 'in_sync' variable when processing bios on the failures list.
The 'in_sync' variable is what is used to determine if the
primary device can be switched in the event of a failure. Since
this has been reset, the primary device is incorrectly assumed
to be not switchable.
The case has been seen in the cluster mirror context, where one
machine realizes the log device is dead before the other machines.
As the responsibilities of the server migrate from one node to
another (because the mirror is being reconfigured due to the failure),
the new server may think for a moment that the log device is fine -
thus resetting the 'log_failure' variable.
In any case, it is inappropiate for us to reset the 'log_failure'
variable. The above bug simply illustrates that it can actually
hurt us.
Cc: stable@kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The output of 'dmsetup table' includes an internal field that should not
be there. This patch removes it. To make the fix simpler, we first
reorder a constructor argument
The 'device size' argument is generated internally. Currently it is
placed as the last space-separated word of the constructor string.
However, we need to use a version of the string without this word, so we
move it to the beginning instead so it is trivial to skip past it.
We keep a copy of the arguments passed to userspace for creating a log,
just in case we need to resend them. These are the same arguments that
are desired in the STATUSTYPE_TABLE request, except for one. When
creating the userspace log, the userspace daemon must know the size of
the mirror, so that is added to the arguments given in the constructor
table. We were printing this extra argument out as well, which is a
mistake.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix 'dmsetup table' output.
There is a missing ' ' at the end of the string causing two
words to run together.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Set sensible I/O hints for striped DM devices in the topology
infrastructure added for 2.6.31 for userspace tools to
obtain via sysfs.
Add .io_hints to 'struct target_type' to allow the I/O hints portion
(io_min and io_opt) of the 'struct queue_limits' to be set by each
target and implement this for dm-stripe.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A couple of recent warning messages make it difficult for the reader to
determine exactly what is wrong. This patch adds more information to
those messages.
The messages were added by these commits:
5dea271b6d ("dm table: pass correct dev area size
to device_area_is_valid")
ea9df47cc9 ("dm table: fix blk_stack_limits arg
to use bytes not sectors")
The patch also corrects references to logical_block_size in printk format
strings from %hu to %u.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The logic to check for valid device areas is inverted relative to proper
use with iterate_devices.
The iterate_devices method calls its callback for every underlying
device in the target. If any callback returns non-zero, iterate_devices
exits immediately. But the callback device_area_is_valid() returns 0 on
error and 1 on success. The overall effect without is that an error is
issued only if every device is invalid.
This patch renames device_area_is_valid to device_area_is_invalid and
inverts the logic so that one invalid device is sufficient to raise
an error.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Implement the .iterate_devices for the origin and snapshot targets.
dm-snapshot's lack of .iterate_devices resulted in the inability to
properly establish queue_limits for both targets.
With 4K sector drives: an unfortunate side-effect of not establishing
proper limits in either targets' DM device was that IO to the devices
would fail even though both had been created without error.
Commit af4874e03e ("dm target:s introduce
iterate devices fn") in 2.6.31-rc1 should have implemented .iterate_devices
for dm-snap.c's origin and snapshot targets.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Functions invoked early when booting up a cpu can't use
tracing because mcount requires a valid 'current_thread_info()'
and TLB mappings to be setup.
The code path of sun4v_register_mondo_queues --> register_one_mondo
is one such case. sun4v_register_mondo_queues already has the
necessary 'notrace' annotation, but register_one_mondo does not.
Normally register_one_mondo is inlined so the bug doesn't trigger,
but with some config/compiler combinations, it won't be so we
must properly mark it notrace.
While we're here, add 'notrace' annoations to prom_printf and
prom_halt so that early error handling won't have the same problem.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Reported-by: Leif Sawyer <lsawyer@gci.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compaq Presario R4000-series laptops are not sending a "volume up button
release" and "volume down button release" signal in the PS/2 protocol for
atkbd. The URL below has some of confirmed reports:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/385477
Signed-off-by: Dave Andrews <jetdog330@hotmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
kmem_cache_destroy() should call rcu_barrier() *after* kmem_cache_close() and
*before* sysfs_slab_remove() or risk rcu_free_slab() being called after
kmem_cache is deleted (kfreed).
rmmod nf_conntrack can crash the machine because it has to kmem_cache_destroy()
a SLAB_DESTROY_BY_RCU enabled cache.
Cc: <stable@kernel.org>
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
The function jffs2_nor_wbuf_flash_setup() doesn't allocate the verify buffer
if CONFIG_JFFS2_FS_WBUF_VERIFY is defined, so causing a kernel panic when
that macro is enabled and the verify function is called. Similarly the
jffs2_nor_wbuf_flash_cleanup() must free the buffer if
CONFIG_JFFS2_FS_WBUF_VERIFY is enabled.
The following patch fixes the problem.
The following patch applies to 2.6.30 kernel.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
Arithmetic conversion in the mask computation makes the upper word
of the second argument passed down to mtd->read_oob(), be always 0
(assuming 'offs' being a 64-bit signed long long type, and
'mtd->writesize' being a 32-bit unsigned int type).
This patch applies over the other one adding masking in nftl_write,
"nftl: write support is broken".
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Write support is broken in NFTL. Fix it.
Signed-off-by: <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a compromise and a temporary workaround for bootup NMI
watchdog triggers some people see with qla2xxx devices present.
This happens when, for example:
CPU 0 is in the driver init and looping submitting mailbox commands to
load the firmware, then waiting for completion.
CPU 1 is receiving the device interrupts. CPU 1 is where the NMI
watchdog triggers.
CPU 0 is submitting mailbox commands fast enough that by the time CPU
1 returns from the device interrupt handler, a new one is pending.
This sequence runs for more than 5 seconds.
The problematic case is CPU 1's timer interrupt running when the
barrage of device interrupts begin. Then we have:
timer interrupt
return for softirq checking
pending, thus enable interrupts
qla2xxx interrupt
return
qla2xxx interrupt
return
... 5+ seconds pass
final qla2xxx interrupt for fw load
return
run timer softirq
return
At some point in the multi-second qla2xxx interrupt storm we trigger
the NMI watchdog on CPU 1 from the NMI interrupt handler.
The timer softirq, once we get back to running it, is smart enough to
run the timer work enough times to make up for the missed timer
interrupts.
However, the NMI watchdogs (both x86 and sparc) use the timer
interrupt count to notice the cpu is wedged. But in the above
scenerio we'll receive only one such timer interrupt even if we last
all the way back to running the timer softirq.
The default watchdog trigger point is only 5 seconds, which is pretty
low (the softwatchdog triggers at 60 seconds). So increase it to 30
seconds for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
I had the codes for L1 D-cache load accesses and misses swapped
around, and the wrong codes for LL-cache accesses and misses.
This corrects them.
Reported-by: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@kernel.org>
LKML-Reference: <19103.8514.709300.585484@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Three bytes of uninitialized kernel memory are currently leaked to user
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The card model detection code introduced in 2.6.30 that tries to work
around partially broken EEPROM contents by reading the EEPROM directly
does not handle cards where the EEPROM has been omitted. In this case,
we have to use the default ID to allow the driver to load.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Ozan Çağlayan <ozan@pardus.org.tr>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New variant of IGDNG mobile chip has new host bridge id.
[anholt: Note that this new PCI ID doesn't impact the DRM, which doesn't
care about the PCI ID of the bridge]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Remember to release the local reference if we fail to wait on
the rendering.
(Also whilst in the vicinity add some whitespace so that the phasing of
the operations is clearer.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some i915/i945 platforms have a fairly high memory latency in certain
situations, so increase our constant a bit to avoid FIFO underruns.
The effect should be positive on other platforms as well; we'll have a
bit more insurance against a busy memory subsystem due to the extra
FIFO entries.
Fixes fdo bug #23368. Needed for 2.6.31.
Tested-by: Sven Arvidsson <sa@whiz.se>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The 32-bit parameters (len and csum) of csum_ipv6_magic() are passed in 64-bit
registers in2 and in4. The high order 32 bits of the registers were never
cleared, and garbage was sometimes calculated into the checksum.
Fix this by clearing the high order 32 bits of these registers.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/dma-mapping.c:14: warning: control reaches end of non-void function
arch/ia64/kernel/dma-mapping.c:14: warning: no return statement in function returning non-void
This warning was introduced by commit: 390bd132b2
Add dma_debug_init() for ia64
Signed-off-by: Tony Luck <tony.luck@intel.com>
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.
And when a qdisc gets reset, that's exactly what we need to do here.
We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.
This reverts the following 3 changesets:
a2cb6a4dd4
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")
38acce2d79
("pkt_sched: Convert CBQ to tasklet_hrtimer.")
ee5f9757ea
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b85a34e91
(net: No more expensive sock_hold()/sock_put() on each tx)
sk_free() frees socks conditionally and depends
on sk_wmem_alloc being set e.g. in sock_init_data(). But in some
cases sk_free() is called earlier, usually after other alloc errors.
Fix is to move sk_wmem_alloc initialization from sock_init_data()
to sk_alloc() itself.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a small typo in the compat ioctl handler that cause the swapext
compat handler to never be called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reviewed-by: Eric Sandeen <sandeen@sandeen.net>
Reviewed-by: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Felix Blyakher <felixb@sgi.com>
The patch "block: Use accessor functions for queue limits"
(ae03bf639a) changed queue_max_sectors_store()
to use blk_queue_max_sectors() instead of directly assigning the value.
But blk_queue_max_sectors() differs a bit
1. It sets both max_sectors_kb, and max_hw_sectors_kb
2. Never allows one to change max_sectors_kb above BLK_DEF_MAX_SECTORS. If one
specifies a value greater then max_hw_sectors is set to that value but
max_sectors is set to BLK_DEF_MAX_SECTORS
I am not sure whether blk_queue_max_sectors() should be changed, as it seems
to be that way for a long time. And there may be callers dependent on that
behaviour.
This patch simply reverts to the older way of directly assigning the value to
max_sectors as it was before.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit 4bc5d34135 is broken and causes regressions:
(1) cpufreq_driver->resume() and ->suspend() were only called on
__powerpc__, but you could set them on all architectures. In fact,
->resume() was defined and used before the PPC-related commit
42d4dc3f4e complained about in 4bc5d34135.
(2) Therfore, the resume functions in acpi_cpufreq and speedstep-smi
would never be called.
(3) This means speedstep-smi would be unusuable after suspend or resume.
The _real_ problem was calling cpufreq_driver->get() with interrupts
off, but it re-enabling interrupts on some platforms. Why is ->get()
necessary?
Some systems like to change the CPU frequency behind our
back, especially during BIOS-intensive operations like suspend or
resume. If such systems also use a CPU frequency-dependant timing loop,
delays might be off by large factors. Therefore, we need to ascertain
as soon as possible that the CPU frequency is indeed at the speed we
think it is. You can do this two ways: either setting it anew, or trying
to get it. The latter is what was done, the former also has the same IRQ
issue.
So, let's try something different: defer the checking to after interrupts
are re-enabled, by calling cpufreq_update_policy() (via schedule_work()).
Timings may be off until this later stage, so let's watch out for
resume regressions caused by the deferred handling of frequency changes
behind the kernel's back.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
percpu incorrectly assumed that cpu0 was always there which led to the
following warning and eventual oops on sparc machines w/o cpu0.
WARNING: at mm/percpu.c:651 pcpu_map+0xdc/0x100()
Modules linked in:
Call Trace:
[000000000045eb70] warn_slowpath_common+0x50/0xa0
[000000000045ebdc] warn_slowpath_null+0x1c/0x40
[00000000004d493c] pcpu_map+0xdc/0x100
[00000000004d59a4] pcpu_alloc+0x3e4/0x4e0
[00000000004d5af8] __alloc_percpu+0x18/0x40
[00000000005b112c] __percpu_counter_init+0x4c/0xc0
...
Unable to handle kernel NULL pointer dereference
...
I7: <sysfs_new_dirent+0x30/0x120>
Disabling lock debugging due to kernel taint
Caller[000000000053c1b0]: sysfs_new_dirent+0x30/0x120
Caller[000000000053c7a4]: create_dir+0x24/0xc0
Caller[000000000053c870]: sysfs_create_dir+0x30/0x80
Caller[00000000005990e8]: kobject_add_internal+0xc8/0x200
...
Kernel panic - not syncing: Attempted to kill the idle task!
This patch fixes the problem by backporting parts from devel branch to
make percpu core not depend on the existence of cpu0.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Meelis Roos <mroos@linux.ee>
Cc: David Miller <davem@davemloft.net>
Do not forget to program the MCLK ratio for the I2S output.
Otherwise, the master clock frequency can be too high for
the DACs at sample frequencies above 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the recent change by Al Viro that changes verious subsystems
to use "struct path" one case was missed in the autofs4 module
which causes mounts to no longer expire.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
My previous patch (commit 4f8ee2c9cc: "lmb: Remove __init from
lmb_end_of_DRAM()") removed __init in lmb.c but missed the fact that it
was also marked as such in the .h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit log for commit 517d3cc15b
("[libata] ata_piix: Enable parallel scan") says:
This patch turns on parallel scanning for the ata_piix driver.
This driver is used on most netbooks (no AHCI for cheap storage it seems).
The scan is the dominating time factor in the kernel boot for these
devices; with this flag it gets cut in half for the device I used
for testing (eeepc).
Alan took a look at the driver source and concluded that it ought to be safe
to do for this driver. Alan has also checked with the hardware team.
and it is all true but once we put all things together additional
constraints for PATA controllers show up (some hardware registers
have per-host not per-port atomicity) and we risk misprogramming
the controller.
I used the following test to check whether the issue is real:
@@ -736,8 +736,20 @@ static void piix_set_piomode(struct ata_
(timings[pio][1] << 8);
}
pci_write_config_word(dev, master_port, master_data);
- if (is_slave)
+ if (is_slave) {
+ if (ap->port_no == 0) {
+ u8 tmp = slave_data;
+
+ while (slave_data == tmp) {
+ pci_read_config_byte(dev, slave_port, &tmp);
+ msleep(50);
+ }
+
+ dev_printk(KERN_ERR, &dev->dev, "PATA parallel scan "
+ "race detected\n");
+ }
pci_write_config_byte(dev, slave_port, slave_data);
+ }
/* Ensure the UDMA bit is off - it will be turned back on if
UDMA is selected */
and it indeed triggered the error message.
Lets fix all such races by adding an extra locking to ->set_piomode
and ->set_dmamode methods for PATA controllers.
[ Alan: would be better to take the host lock in libata-core for these
cases so that we fix all the adapters in one swoop. "Looks fine as a
temproary quickfix tho" ]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Improve CRTDDC mapping by using VBT info
drm/i915: Fix CPU-spinning hangs related to fence usage by using an LRU.
drm/i915: Set crtc/clone mask in different output devices
drm/i915: Always use SDVO_B detect bit for SDVO output detection.
drm/i915: Fix typo that broke SVID1 in intel_sdvo_multifunc_encoder()
drm/i915: Check if BIOS enabled dual-channel LVDS on 8xx, not only on 9xx
drm/i915: Set the multiplier for SDVO on G33 platform
This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.
Reference: kernel bug#14078
http://bugzilla.kernel.org/show_bug.cgi?id=14078
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element. Simpliy
adding the call of get_mux_nids() fixes the problem.
Reference: Novell bnc#534904
https://bugzilla.novell.com/show_bug.cgi?id=534904
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should call em28xx_ir_init(dev) only when disable_ir is true.
Signed-off-by: Shine Liu <shinel@foxmail.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
