We want to use the "struct slab" size, not the size of the pointer to
same. As it is, we'd not print out the last <n> entry pointers in the
slab (where <n> is ~10, depending on whether it's a 32-bit or 64-bit
kernel).
Gaah, that slab code was written by somebody who likes unreadable crud.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
memset() is called before check.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Steinar H. Gunderson reported:
- For some reason, it detects the 9845 as a 9735 -- it appears this is
simply related to the ordering in parport_serial_pci_tbl[]. If we move
the 9845 up above the 9735, it prints out 9710:9845, but no change in
behaviour. (We didn't find out why this was the case; we left it alone
since it didn't affect our problem.)
- The card has no parallel port (at least no physical ones), yet it reports
(via its subsystem ID of 0x0014) one parallel port and four serial ports.
The probe for the parallel port fails, and the driver just aborts. Thus,
it doesn't find the serial ports.
Fix the debugging code to use dev_dbg, but don't bother displaying the
PCI ID of the detected board (that's accessible via other means.)
Also, arrange for parport_register() to return 0 even if it finds no
ports.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We must use the "a" (allocate) attribute every time we
emit an entry into the __ex_table section.
For consistency, use "a" instead of #alloc which is some
Solaris compat cruft GNU as provides on Sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances 0 is returned by dccp_li_hist_calc_i_mean which
leads to a divide by zero in ccid3_hc_rx_packet_recv. Explicitly check
for zero return now. Update copyright notice at same time.
Found by Arnaldo.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
The earlier round of kobject/sysfs changes to bridge caused
it not to generate a uevent on removal. Don't think any application
cares (not sure about Xen) but since it generates add uevent
it should generate remove as well.
Signed-off-by: Stephen Hemminger <shemmigner@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the STP timers for a port when it is created,
rather than when it is enabled. This will prevent future race conditions
where timer gets started before port is enabled.
Signed-off-by: Stephen Hemminger <shemmigner@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge would crash because of uninitailized timer if STP is used and
device was inserted into a bridge before bridge was up. This got
introduced when the delayed port checking was added. Fix is to not
enable STP on port unless bridge is up.
Bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=6140
Dup: http://bugzilla.kernel.org/show_bug.cgi?id=6156
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
session when multiply mounted.
Fixes slow response when cifs client is mounted to shares on multiple
servers and oplock break occurs (usually due to attempt to multiply open a
file). When treeids on mutiple mounted shares match and we find the wrong
match first, we searched for the wrong cached files to send oplock break
response for which usually meant that no matching file was found and thus
the server would have to timeout the notification. Oplock break timeout is
about 20 seconds on some servers so this could cause significantly slower
performance on file open calls in a few cases (in particular when multiple
shares are mounted from multiple servers, tree ids match, and we have a
cached file which is later opened multiple times). This was the most
important of the bugs that was found and fixed at Connectathon
(interoperability testing event) this week.
Acked-by: Shaggy (shaggy@austin.ibm.com)
Signed-off-by: Steve French (sfrench@us.ibm.com)
* master.kernel.org:/home/rmk/linux-2.6-mmc:
[MMC] au1xmmc: Fix a compilation warning ('status' is not used)
[MMC] au1xmmc: Fix linking error because mmc_rsp_type doesn't exist
[MMC] au1xmmc: Fix compilation error by using platform_driver
Fix a trivial compilation warning:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_dma_callback’:
drivers/mmc/au1xmmc.c:743: warning: unused variable ‘status’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c doesn't compile because commit
e92251762d introduced a typo and passes
the wrong argument to the mmc_resp_type macro.
Error because of the typo:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: warning: implicit declaration of function ‘mmc_rsp_type’
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `au1xmmc_request':au1xmmc.c:(.text+0x89504): undefined reference to `mmc_rsp_type'
:au1xmmc.c:(.text+0x8968c): undefined reference to `mmc_rsp_type'
make: *** [.tmp_vmlinux1] Error 1
Error because of the wrong argument:
CC drivers/mmc/au1xmmc.o
drivers/mmc/au1xmmc.c: In function ‘au1xmmc_send_command’:
drivers/mmc/au1xmmc.c:197: error: invalid type argument of ‘->’
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mmc/au1xmmc.c currently doesn't compile; it needs to be
converted to use platform_driver. I cannot test this change because
of lack of hardware but I followed the drivers this one is based on,
and the code is certainly not worse than before.
drivers/mmc/au1xmmc.c: At top level:
drivers/mmc/au1xmmc.c:1002: error: ‘platform_bus_type’ undeclared here (not in a function)
make[2]: *** [drivers/mmc/au1xmmc.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
yaboot is scrogged and calls us with an invalid stack alignment,
it seems.
Thanks to David Woodhouse to pointing me to the problem.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Checking e100.c code against Documentation/io_ordering.txt I found the
following problem:
spin_lock_irq...
write
spin-unlock
e100_write_flush
The attached patch fix the code like this:
spin_lock_irq...
write
e100_write_flush
spin-unlock
Signed-off-by: Catalin BOIE <catab@umbrella.ro>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As documented in National application note 1287 the RX state machine on
the natsemi chip can lock up under some conditions (mostly related to
heavy load). When this happens a series of bogus packets are reported
by the chip including some oversized frames prior to the final lockup.
This patch implements the fix from the application note: when an
oversized packet is reported it resets the RX state machine, dropping
any currently pending packets.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts the natsemi driver to use NAPI. It was originally
based on one written by Harald Welte, though it has since been modified
quite a bit, most extensively in order to remove the ability to disable
NAPI since none of the other drivers seem to provide that functionality
any more.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mac_addr variable doesn't get reset between
(re)additions of multicast addresses. One byte
of all multicast addresses (except the first)
can be incorrect.
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This documentation is mostly obsolete, and should therefore either be
updated or removed (this patch does the latter).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This adds support for the 4th port and other new features of the
BCM1480 SOC.
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Almost all the code for the VIA RNG is guarded with __i386__ #ifdefs,
the only exception being the enumeration of RNG types which is used to
index into the rng_vector ops array. This patch adds an ifdef around
that for consistency and since the guard makes a difference when adding
new RNG types on non-i386 hardware.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-Off-By: Jeff Garzik <jeff@garzik.org>
Originally submitted by Kenzo Iwami; his original description is:
The current bonding driver receives duplicate packets when broadcast/
multicast packets are sent by other devices or packets are flooded by the
switch. In this patch, new flags are added in priv_flags of net_device
structure to let the bonding driver discard duplicate packets in
dev.c:skb_bond().
Modified by Jay Vosburgh to change a define name, update some
comments, rearrange the new skb_bond() for clarity, clear all bonding
priv_flags on slave release, and update the driver version.
Signed-off-by: Kenzo Iwami <k-iwami@cj.jp.nec.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
