It is now possible to specify a ccw/fcp dump device which is used to
automatically create a system dump in case of a kernel panic. The dump
device can be configured under /sys/firmware/dump.
In addition it is now possible to specify a ccw/fcp device which is used
for the next reboot of Linux. The reipl device can be configured under
/sys/firmware/reipl.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Correct some comments in the hypervisor filesystem.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move initrd if the bitmap of the bootmem allocator would overwrite it.
In addition this patch sets the default size and address of the initrd to 0.
Therefore all boot loaders must set the initrd size and address correctly.
This is especially relevant for ftp boot via HMC/SE, where this change
requires a special patch file entry in the .ins file which sets these two
values contained at address 0x10408 and 0x10410.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Grundy <grundym@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This abstracts the operations used in the bootwrapper, and defines
the operations needed for the bootwrapper to run on an OF platform.
The operations have been divided up into platform ops (platform_ops),
firmware ops (fw_ops), device tree ops (dt_ops), and console ops
(console_ops).
The proper operations will be hooked up at runtime to provide the
functionality that you need.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This produces essentially the same code and will make the iSeries i/o
consolidation easier.
The count parameter is changed to long since that will produce the same
(better) code on 32 and 64 bit builds.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
The io accessors insw_ns, outsw_ns, insl_ns and outsl_ns are unused
(except for one unnecessary use in drivers/net/3c509.c that is addressed
in a previous patch) and are only defined in powerpc/ppc, so remove them.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This reverts commits 11012d419c and
40dd2d20f2, which allowed us to use the
MMIO accesses for PCI config cycles even without the area being marked
reserved in the e820 memory tables.
Those changes were needed for EFI-environment Intel macs, but broke some
newer Intel 965 boards, so for now it's better to revert to our old
2.6.17 behaviour and at least avoid introducing any new breakage.
Andi Kleen has a set of patches that work with both EFI and the broken
Intel 965 boards, which will be applied once they get wider testing.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(And reset it on new thread creation)
It turns out that eflags is important to save and restore not just
because of iopl, but due to the magic bits like the NT bit, which we
don't want leaking between different threads.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3815/1: headers_install support for ARM
[ARM] 3794/1: S3C24XX: do not defined set_irq_wake when no CONFIG_PM
[ARM] 3793/1: S3C2412: fix wrong serial info struct
[ARM] 3780/1: Fix iop321 cpuid
[ARM] 3786/1: pnx4008: update defconfig
[ARM] 3785/1: S3C2412: Fix idle code as default uses wrong clocks
[ARM] 3784/1: S3C2413: fix config for MACH_S3C2413/MACH_SMDK2413
This patch corrects the buffer length checking in the
sys_getdomainname() implementation for sparc/sparc64.
Signed-off-by: Andy Walker <andy@puszczka.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
Do not define set_irq_wake as a real function if
the CONFIG_PM option is not set.
Fixes bug reported by Thomas Gleixner.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dan Williams
commit a6a38a6622 changed the iop321 id to a value that does not work with all platforms. Change the mask to permit bit 11. Tested on an iq80321 600Mhz CRB.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Fix the idle code on the s3c2412 as the default
code is using bits in the CLKCON register that are
no-longer there.
Provide an override for the idle code, and ensure
that the power configuration is set to allow idle
instead of stop or sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
These two machines are identical, and supported
by the SMDK2413 configuration. When MACH_SMDK2413
is selected, we must also select MACH_S3C2413
to allow machine_is_smdk2413() or machine_is_s3c2413()
to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a compile error that only surfaces on CONFIG_SMP=n builds;
<asm/hvcall.h> seems to get pulled in through another header file for
SMP builds. This problem was introduced by the hvcall stats patch.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It seems that the occasional data corruption observed with the tg3
driver wasn't due to missing barriers after all, but rather seems to
be due to the DART (= IOMMU) in the U4 northbridge reading stale
IOMMU table entries from memory due to a race. This fixes it by
making the CPU read the entry back from memory before using it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Tested on G5 (PPC970) and POWER5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export copy_4K_page() for use by modules via copy_page() (such as
CacheFiles).
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xmon does not print a backtrace per default. This is bad on systems with
USB keyboard, the most needed info about the crash is lost.
print a backtrace during the very first xmon entry.
Booting with xmon=nobt disables the autobacktrace functionality.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix the following whitespace warnings when compiling with ARCH=ppc
arch/ppc/Kconfig:1207:warning: leading whitespace ignored
arch/ppc/Kconfig:1226:warning: leading whitespace ignored
arch/ppc/Kconfig:1231:warning: leading whitespace ignored
Also fix a typo ("Supprt").
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add instrumentation for hypervisor calls on pseries. Call statistics
include number of calls, wall time and cpu cycles (if available) and
are made available via debugfs. Instrumentation code is behind the
HCALL_STATS config option and has no impact if not enabled.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Base patch for PA6T and PA6T-1682M. This introduces the
arch/powerpc/platform/pasemi directory, together with basic
implementations for various setup.
Much of this was based on other platform code, i.e. Maple, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reduce default cacheline size on 64-bit powerpc from 128 bytes to 64.
This is the architected minimum. In most cases we'll still end up using
cache line information from the device tree, but defaults are used during
early boot and doing a few dcbst/icbi's too many there won't do any harm.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following patch allows XMON to run on the 4xx platform. Tested on
Walnut, Ebony, and Nova (440GX based) eval boards. 440EP, 440SP, and
440SPE boards should work as well. Patch is against 2.6.18-rc6.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the pm_power_off function variable in PPC to work as an override.
This makes the function consistent with the other architectures and it
allows generic poweroff operations (like those provided in IPMI
systems) to work properly on PPC.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Joseph Barnett <jbarnett@motorola.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In an attempt to make it easier for a power5 optimized app to run on a
power4 or a 970 or random earlier machine, this provides emulation of
the popcntb instruction.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As part of the new irq code pseries_kexec_cpu_down() was split into a
xics and mpic version. The vpa unregister logic is now only done in the
xics routine, and although that's ok in practice (we don't have SPLPAR
machines with mpic), I'd rather have the two concepts stay separate.
So move the vpa unregister into pseries_kexec_cpu_down(), which gets called
by both the xics and mpic routines. This also gives us an obvious place to
put any new kexec-down logic needed in future.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call chip->eoi(irq) to clear any pending interrupt in case of kdump
shutdown sequence. chip->end(irq) does not serve this purpose.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update PReP defconfig, disable some drivers for hardware that is not
used on those systems; enable SL82C105 IDE driver for Powerstack.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'audit.b29' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] sparc64 audit syscall classes hookup
[PATCH] syscall class hookup for all normal targets
... that should do it for all targets; the only remaining issues are
mips (currently treated as non-biarch) and handling of other OS
emulations (OSF/SunOS/Solaris/???). The latter would need to be
assigned new AUDIT_ARCH_... ABI numbers anyway...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Take default arch/*/kernel/audit.c to lib/, have those with special
needs (== biarch) define AUDIT_ARCH in their Kconfig.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
sh64 wasn't providing a sensible pm_power_off(), add one,
and just wrap it to machine_power_off, which already does
the right thing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While we've been sorting out the toolchain fiasco, some of
the code has suffered a bit of bitrot. Building with GCC4
also brings up some more build warnings. Trivial fixes for
both issues.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The original sh64 toolchains required that we tune the ISA
level accordingly to not have head.S/entry.S blow up. With
current toolchains, this is no longer the case, and the
syntax magically changed as well, causing all current
toolchains to die a horrible death.
Incidentally, code generation in other parts of the kernel
is now significantly complex enough that none of the older
toolchains make it very far these days, so there's not
even any point in preserving legacy compatability via
as-option.
This fixes a long-standing issue, as noted here:
http://lkml.org/lkml/2005/1/5/223
Though at the time the current toolchains were too broken
to make adjusting the tuning worthwhile.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3778/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [simtec]
[ARM] 3783/1: S3C2412: fix IRQ_EINT0 to IRQ_EINT3 handling
[ARM] 3779/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [left]
[ARM] 3777/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410 [regs-*.h]
[ARM] 3776/1: S3C24XX: remove changelogs from include/asm-arm/arch-s3c2410
[ARM] 3775/1: S3C24XX: do not add same sysdev_driver to two classes
[ARM] 3774/1: S3C24XX: SMDK2413 has two machine IDs
[ARM] 3773/1: Add the HWCAP_VFP bit for the ARM926 CPUs
[ARM] 3772/1: Fix compilation error in mach-ixp4xx/nslu2*
[ARM] 3767/1: S3C24XX: remove changelog comments from arch/arm/mach-s3c2410
[ARM] 3766/1: Fix typo in ARM _raw_read_trylock
Patch from Ben Dooks
The IRQ_EINT0 through IRQ_EINT3 handling has changed
on the S3C2412 from the previous SoCs in the range,
and thus we need to add code to handle this.
The changes come about due to these IRQs being
displayed in two different registers, and needing to
be acked and masked in both.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c244x-irq.c code makes the mistake of adding
the same drive to two different sys-classes. This
causes the class lists to become corrupted and the
suspend code to OOPS.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sn_cpu_init() is required for cpu initialization on SN platforms.
Change __init to __cpuinit so that the function is not freed with init code/data.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The SN PROM uses the register stack in the slave loop. The contents
must be preserved for the OS to return to the slave loop via offlining
a cpu or for kexec. A 'flushrs" is needed to force the stack to be written
to memory prior to changing bspstore.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The syscalls set/get_robust_list must not be wired up until
futex_atomic_cmpxchg_inatomic is implemented. Otherwise the kernel will
hang in handle_futex_death.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix a bug in sys_perfmonctl() whereby it was not correctly
decrementing the file descriptor reference count.
Signed-off-by: stephane eranian <eranian@hpl.hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This prevents cross-region mappings on IA64 and SPARC which could lead
to system crash. They were correctly trapped for normal mmap() calls,
but not for the kernel internal calls generated by executable loading.
This code just moves the architecture-specific cross-region checks into
an arch-specific "arch_mmap_check()" macro, and defines that for the
architectures that needed it (ia64, sparc and sparc64).
Architectures that don't have any special requirements can just ignore
the new cross-region check, since the mmap() code will just notice on
its own when the macro isn't defined.
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[ Cleaned up to not affect architectures that don't need it ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
It turns out we have both SMDK2413 and S3C2413 for
the same board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The ARM926EJ-S CPU has the VFP coprocessor and therefore it should be shown
in the /proc/cpuinfo if CONFIG_VFP is enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Martin Michlmayr
Include linux/irq.h in the nslu2 code in order to avoid the following
compiler error:
CC arch/arm/mach-ixp4xx/nslu2-power.o
arch/arm/mach-ixp4xx/nslu2-power.c: In function 'nslu2_power_init':
arch/arm/mach-ixp4xx/nslu2-power.c:53: warning: implicit declaration of function 'set_irq_type'
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: 'IRQ_TYPE_LEVEL_LOW' undeclared (first use in this function)
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: (Each undeclared identifier is reported only once
arch/arm/mach-ixp4xx/nslu2-power.c:53: error: for each function it appears in.)
arch/arm/mach-ixp4xx/nslu2-power.c:54: error: 'IRQ_TYPE_LEVEL_HIGH' undeclared (first use in this function)
make[5]: *** [arch/arm/mach-ixp4xx/nslu2-power.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove the pointless changelog comments from
arch/arm/mach-s3c2410 files, as all this can
be found from the revision control system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the generic time stuff for FRV.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some buggy BIOSes do a "software any" kind of coordination without telling
about it to OS. So, when OS sets frequency on one CPU on these platforms,
it will also impact all the other logical CPUs that are in the same power
domain. Attached patch is a workaround for those buggy BIOSes.
Patch should be a noop on the normal non-buggy platforms.
Applies over previously sent acpi-cpufreq and software coordination
bug fix patch
Signed-off-by: Denis Sadykov <denis.m.sadykov@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Rename option "dont_scale_voltage" to "scale_voltage" because
don't will be default.
Use "pos" for calculating voltage. In this way driver don't need
to know mV value or low level value. Simply min U is one pos and
max U is second pos. All pos between these two are used.
Assume that min U is for min f and max U for max f. For frequency
between min and max calculate pos based on difference between
current frequency and min f.
Values in mobile VRM table changed to values from
C3-M datasheet.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
New sparse caught that typo which could have caused erratic hardware
behaviour on some machines if the platform functions are used by the
firmware to change bits in some FCR registers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from George G. Davis
Resolve ARM1136 VIPT non-aliasing cache coherency issues observed when
using ptrace to set breakpoints and cleanup copy_{to,from}_user_page()
while we're here as requested by Russell King because "it's also far
too heavy on non-v6 CPUs".
NOTES:
1. Only access_process_vm() calls copy_{to,from}_user_page().
2. access_process_vm() calls get_user_pages() to pin down the "page".
3. get_user_pages() calls flush_dcache_page(page) which ensures cache
coherency between kernel and userspace mappings of "page". However
flush_dcache_page(page) may not invalidate I-Cache over this range
for all cases, specifically, I-Cache is not invalidated for the VIPT
non-aliasing case. So memory is consistent between kernel and user
space mappings of "page" but I-Cache may still be hot over this
range. IOW, we don't have to worry about flush_cache_page() before
memcpy().
4. Now, for the copy_to_user_page() case, after memcpy(), we must flush
the caches so memory is consistent with kernel cache entries and
invalidate the I-Cache if this mm region is executable. We don't
need to do anything after memcpy() for the copy_from_user_page()
case since kernel cache entries will be invalidated via the same
process above if we access "page" again. The flush_ptrace_access()
function (borrowed from SPARC64 implementation) is added to handle
cache flushing after memcpy() for the copy_to_user_page() case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The port to genirq & the new powerpc interrupt model in 2.6.18 introduced a
bug in the legacy PowerMac PIC code (used on older machines) because of a
typo potentially causing hangs due to interrupt storms. This fixes it,
along with a performance issue causing us to do spurrious retriggers after
masking an interrupt.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently some systems export valid HPET addresses, but hpet_enable()
fails. Then when the HPET clocksource starts up, it only checks for a
valid HPET address, and the result is a system where time does not advance.
See http://bugme.osdl.org/show_bug.cgi?id=7062 for details.
This patch just makes sure we better check that the HPET is functional
before registering the HPET clocksource.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
The type naming in the s3c24xx dma code is riddled with
typedefs creating _t types, from the code import from 2.4
which is contrary to the current Kernel coding style.
This patch cleans this up, removing the typedefs and
and fixing up the resultant code changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
This adds RTC support to the csb337 default config. Both the AT91
and the ds1307 RTCs are enabled (rtc0 and rtc1 respectively).
The ds1307 is used to initialize the system time, since it's battery-backed.
From then on the AT91 RTC is used, since it's more capable (with both
alarm and update irqs, and system wakeup capability) even though it
needs manual initialization (symlink /dev/rtc to /dev/rtc0 for older
versions of hwclock, then "hwclock --systohc") in an rc script or
from inittab.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix return value from memcpy
[POWERPC] iseries: Define insw et al. so libata/ide will compile
[POWERPC] Fix irq enable/disable in smp_generic_take_timebase
[POWERPC] Fix problem with time not advancing on 32-bit platforms
[POWERPC] Restore copyright notice in arch/powerpc/kernel/fpu.S
[POWERPC] Fix up ibm_architecture_vec definition
[POWERPC] Make OF irq map code detect more error cases
[POWERPC] Support for "weird" MPICs and fixup mpc7448_hpc2
[POWERPC] Fix MPIC sense codes in documentation
[POWERPC] Fix performance regression in IRQ radix tree locking
[POWERPC] Add mpc7448hpc2 device tree source file
[POWERPC] Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
[POWERPC] modify mpc83xx platforms to use new IRQ layer
[POWERPC] Adapt ipic driver to new host_ops interface, add set_irq_type to set IRQ sense
[POWERPC] back up old school ipic.[hc] to arch/ppc
[POWERPC] Use mpc8641hpcn PIC base address from dev tree.
[POWERPC] Allow MPC8641 HPCN to build with CONFIG_PCI disabled too.
[POWERPC] Fix powerpc 44x_mmu build
[POWERPC] Remove flush_dcache_all export
This fixes a hang on ppc32.
The problem was that I was comparing a 32-bit quantity with a 64-bit
quantity, and consequently time wasn't advancing. This makes us use a
64-bit quantity on all platforms, which ends up simplifying the code
since we can now get rid of the tb_last_stamp variable (which actually
fixes another bug that Ben H and I noticed while going carefully through
the code).
This works fine on my G4 tibook. Let me know how it goes on your
machines.
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As pointed out by Herbert Xu <herbert@gondor.apana.org.au>, our
memcpy implementation didn't return the destination pointer as its
return value, and there is code in the kernel that expects that.
This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Increase default nodes shift to 10, nr_cpus to 1024
[IA64] remove redundant local_irq_save() calls from sn_sal.h
[IA64] panic if topology_init kzalloc fails
[IA64-SGI] Silent data corruption caused by XPC V2.
It's possible to get an invalid page fault in kernel mode when we try to
write out segments from vsyscall32 when dumping core for a 32bit process if
the vsyscall32 DSO is not mapped in its address space (which can happen if,
for example, ulimit -v 100 is run).
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The values in init_tss.ist[] can change when an IST event occurs. Save
the original IST values for checking stack addresses when debugging or
doing stack traces.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was a bogus hunk from the genirq merge that essentially
broke stack switching for hard interrupts. Remove it since it isn't
needed.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a replacement for the earlier removal of the e820 MCFG check
we blacklist the Intel SDV with the original BIOS bug that
motivated that check. On those machines don't use MMCONFIG.
This also adds a new pci=mmconf parameter to override the blacklist.
Cc: Greg KH <gregkh@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Noticed by Jan Beulich.
When the kernel was moved from 1MB to 2MB in 2.6.17 the kernel reservation
code wasn't adjusted and it still reserved starting with 1MB. This means 1MB always
were lost.
This patch fixes this by reserving only starting with _text.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The unwinder fallback logic still had potential for falling through to
the legacy stack trace code without printing an indication (at once
serving as a separator) of this.
Further, the stack pointer retrieval for the fallback should be as
restrictive as possible (in order to avoid having the legacy stack
tracer try to access invalid memory). The patch tightens that, but
this could certainly be further improved.
Also making the call_trace command line option now conditional upon
CONFIG_STACK_UNWIND (as it's meaningless otherwise).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One open question: Should this added push perhaps be made conditional
upon CONFIG_STACK_UNWIND or CONFIG_UNWIND_INFO?
[AK: not needed, these are all very slow paths]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One open question: Should these added pushes perhaps be made
conditional upon CONFIG_STACK_UNWIND or CONFIG_UNWIND_INFO?
[AK: Not needed -- these are all very slow paths]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The check for the MCFG table being reserved in the e820 map was originally
added to detect a broken BIOS in a preproduction Intel SDV. However it also
breaks the Apple x86 Macs, which can't supply this properly, but need
a working MCFG. With this patch they wouldn't use the MCFG and not work.
After some discussion I think it's best to remove the heuristic again.
It also failed on some other boxes (although it didn't cause much
problems there because old style port access for PCI config space
still works as fallback), but the preproduction SDVs can just use
pci=nommcfg. Supporting production machines properly is more
important.
Edgar Hucek did all the debugging work.
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Edgar Hucek <hostmaster@ed-soft.at>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Daniel Jacobowitz
vfp_put_double didn't work in a CONFIG_AEABI kernel. By swapping
the arguments, we arrange for them to be in the same place regardless
of ABI. I made the same change to vfp_put_float for consistency.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The copy_in_user primitive does not work as advertised. If the source
and target area are available copy_in_user copies one byte too much.
If one of the memory areas is not available it does not copy as much
data as it can, but up to 257 bytes less.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Eran Ben-Avi <eranpublic@yahoo.com> pointed out that the arch/ppc version
of smp_generic_take_timebase disables interrupts on entry but exits without
restoring them. However, both it and the arch/powerpc version have another
problem, which is that they use local_irq_disable/enable rather than
local_irq_save/restore, and they are called with interrupts disabled.
This fixes both problems; it changes a return to a break in the arch/ppc
version, and changes both versions to use local_irq_save/restore.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a problem introduced in 5db9fa9593.
The last_jiffy per-cpu variable is only 32 bits on 32-bit machines, but it
was being compared with a 64-bit quantity (tb_next_jiffy), which resulted in
time not advancing.
This fixes it by changing last_jiffy to be 64 bits on all platforms. With
this, we no longer need tb_last_stamp as a 32-bit version of tb_last_jiffy,
so this gets rid of tb_last_stamp and we just use tb_last_jiffy instead.
This also fixes a bug when the boot cpu is not online, because using
tb_last_stamp could have caused the wrong timebase origin value to be used
when calculating the time of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This code got moved from head.S but the copyright notice on head.S didn't
get transferred with it. Noticed by Cort Dougan <cort@fsmlabs.com>.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This problem was noticed by one of the Phyp firmware folks.
Our ibm,client-architecture-support call was failing.
This corrects the vector length parameters being passed in.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device-tree bugs on js20 with some versions of SLOF were causing the
interrupt for IDE to not be parsed correctly and fail to boot. This
patch adds a bit more sanity checking to the parser to detect some of
those errors and fail instead of returning bogus information. The
powerpc PCI code can then trigger a fallback that works on those
machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a new hardware information table for mpic. This enables
the mpic code to deal with mpic controllers with different register
layouts and hardware behaviours.
This introduces CONFIG_MPIC_WEIRD. For boards with non standard mpic
controllers, select CONFIG_MPIC_WEIRD and add its hardware information
in the mpic_infos[] array.
TSI108/109 PIC takes the first index of weird hardware information
table. :) The table can be extended. The Tsi108/109 PIC looks like
standard OpenPIC but, in fact, is different in register mapping and
behavior.
The patch does not affect the behavior of standard mpic. If
CONFIG_MPIC_WEIRD is not defined, the code is essentially identical to
the current code.
[benh@kernel.crashing.org:
This patch is a slightly cleaned up version of Zang Roy's support for
the TSI108 MPIC variant. It also fixes up MPC7448_hpc2 to use the new
version of the type macros and changes the way MPIC is selected in
Kconfig to better match what is done for other system devices.
]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This problem was introduced by changeset
14778d9072
Unlike the hugetlb code paths, the normal fault code is not setup to
propagate PTE changes for large page sizes correctly like the ones we
make for I/O mappings in io_remap_pfn_range().
It is absolutely necessary to update all sub-ptes of a largepage
mapping on a fault. Adding special handling for this would add
considerably complexity to tlb_batch_add(). So let's just side-step
the issue and forcefully dirty any writable PTEs created by
io_remap_pfn_range().
The only other real option would be to disable to large PTE code of
io_remap_pfn_range() and we really don't want to do that.
Much thanks to Mikael Pettersson for tracking down this problem and
testing debug patches.
Signed-off-by: David S. Miller <davem@davemloft.net>
When reworking the powerpc irq code, I figured out that we were using
the radix tree in a racy way. As a temporary fix, I put a spinlock in
there. However, this can have a significant impact on performances. This
patch reworks that to use a smarter technique based on the fact that
what we need is in fact a rwlock with extremely rare writers (thus
optimized for the read path).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the mpc7448hpc2 device tree source file.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code.
renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This converts ipic code to Benh's IRQ mods. For the IPIC, IRQ sense values in the device tree equal those in include/linux/irq.h; that's 8 for low assertion (most internal IRQs on mpc83xx), and 2 for high-to-low change.
spinlocks added to [un]mask, ack operations; default handler and type now set in host_map; and redundant condition check eliminated.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Keep from breaking 83xx arch/ppc build. Back up old school arch/powerpc/sysdev/ipic.[hc] to arch/ppc/syslib.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change both the NODES_SHIFT and the NR_CPUS so that even big machines
can boot all nodes and processors with a generic kernel.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3761/1: fix armv4t breakage after adding thumb interworking to userspace helpers
[ARM] Add Integrator support for glibc outb() and friends
[ARM] Move prototype for register_isa_ports to asm/io.h
[ARM] Arrange for isa.c to use named initialisers
[ARM] 3741/1: remove sa1111.c build warning on non-sa1100 systems
[ARM] 3760/1: This patch adds timeouts while working with SSP registers. Such timeouts were en
[ARM] 3758/1: Preserve signalling NaNs in conversion
[ARM] 3749/3: Correct VFP single/double conversion emulation
[ARM] 3748/3: Correct error check in vfp_raise_exceptions
Patch from Lennert Buytenhek
On armv4t systems, we have always compiled the kernel with -march=armv4
instead of -march=armv4t, which means that any use of bx will bomb out.
Commit ba9b5d7637 introduced the use of
bx in the kernel, which means we need to compile with -march=armv4t on
armv4t systems now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the necessary call to register_isa_ports() so that glibc knows
where these are found on Integrator platforms.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we select NUMA with i386, the system is only X86_NUMAQ or using ACPI.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ignore the return value of early_init_acpi(), as it can give false error
messages. If there is something really wrong, then register_driver will
fail cleanly with EINVAL later.
[ background: modprobe acpi-cpufreq on systems not capable of speed-scaling
started failing with 'invalid argument', where previously it would only
ever -ENODEV
I'm not 100% happy with the solution. It'd be better to handle
failure properly, but this is a low-impact change for 2.6.18
We can always revisit doing this better in .19 --davej.]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from David Brownell
Remove buld warning when building sa1111 on non-sa1100 platforms (e.g. PXA).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Paul Sokolovsky
This patch adds timeouts while working with SSP registers. Such
timeouts were envisioned by docstrings in ssp.c, but were not
implemented. There were actual lockups while accessing
touchscreen for iPaqs h1910, h4000 due to lack of the timeouts.
This is updated version of previously submitted patch: 3738/1.
Signed-off-by: Paul Sokolovsky <pmiscml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtds and fcvtsd instructions were generating a qnan bit pattern
for both quiet and signalling NaNs.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The fcvtsd/fcvtds emulation was left behind when the numbering of double
precision registers was changed from 0-30 to 0-15. Both conversion
instructions were writing their results to the wrong register. Also,
the conversion instructions should stop after the first element even
if a vector length is specified.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
The recent fix to hide VFP_NAN_FLAG broke the check in vfp_raise_exceptions;
it would attempt to deliver an exception mask of 0xfffffeff instead of reporting
a serious error condition using printk. Define a safe constant to use for
an invalid exception maskm, and use it at both ends.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It moves the smp_procesors_ready variable to sun4d_smp.c only.
Signed-off-by: Krzysztof Helt (krzysztof.h1@wp.pl)
Signed-off-by: David S. Miller <davem@davemloft.net>
smp_setup_cpu_possible_map() needs to run after paging_init()
so that the in-kernel device tree is setup.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
On i386 PCI mmconfig forgets the bus number when setting the fallback_slots
bits which means fallback to conf1 only works for bus 0.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
there was a change in 2.6.17 which affected the order in which the PCI
access methods are probed. this gives regressions on some machines with
broken BIOS. the problem is that PCBIOS sometimes reports last bus wrong,
leaving cardbus non-funcational. previously those system worked fine with
direct access.
The patch changes the PCI init code to have PCBIOS as last fallback, yet
the PCBIOS code still has to run first to set pcibios_last_bus to the value
reported by the BIOS. this is needed in case legacy PCI probing
(arch/i386/pci/legacy.c) is used to detect peer busses. using direct
access if available fixes the cardbus problems.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After going through the trouble of setting up the PIC base
address in the pic@40000 device tree node, use it instead
of the obsolete hard-coded value.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PIN_SIZE definition name changed, update 44x_mmu.c accordingly.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removes the flush_dcache_all export for non coherent platforms.
We removed the last in-kernel user of this years ago in arch/ppc
so it no longer serves a purpose. Plus, it breaks the build
at the moment.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only call into RTAS when booted with panic=0 because the RTAS call
does not return. The system has to be rebooted via the HMC or via the
management console right now. This is cumbersome and not what the
default panic=180 is supposed to do.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
gcc 4.1 produces some warnings that say it is ignoring the packed
attribute on some structure elements, so, since all the elements of
these structs are packed, pack the structs instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Several RTAS calls take a "config_addr" parameter, which is a particular
way of specifying a PCI busno, devfn and register number into a 32-bit word.
Currently these are open-coded, and I'll be adding another soon, replace
them with a helper that encapsulates the logic. Be more strict about masking
the busno too, just in case.
Booted on P5 LPAR.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Just one bit of fallout from the constification of the get_property
return value.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rtas console doesn't have to be Cell specific. If we get both
RTAS tokens, we should just enabled the console then and there.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup CPU inits a bit more, Geoff Levand already did some earlier.
* Move CPU state save to cpu_setup, since cpu_setup is only ever done
on cpu 0 on 64-bit and save is never done more than once.
* Rename __restore_cpu_setup to __restore_cpu_ppc970 and add
function pointers to the cputable to use instead. Powermac always
has 970 so no need to check there.
* Rename __970_cpu_preinit to __cpu_preinit_ppc970 and check PVR before
calling it instead of in it, it's too early to use cputable.
* Rename pSeries_secondary_smp_init to generic_secondary_smp_init since
everyone but powermac and iSeries use it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename cpu_setup_power4.S to cpu_setup_ppc970.S, since that's
really what it is.
No functional or other changes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup some of the #define magic as suggested by Milton.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There really is no sense trying to continue if the kzalloc of sysfs_cpus[]
fails in ia64 topology_init. The code calling into here doesn't check
errors very well, and one ends up with a nonobvious boot failure that
wastes peoples time debugging.
See for example the lkml thread at:
http://lkml.org/lkml/2006/3/2/215
Since the system is totally dead when this kzalloc fails, not having yet
even booted, might as well announce one's death boldly and plainly.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On Tue, 2006-08-15 at 08:22 -0700, Dave Hansen wrote:
> kernel BUG in cache_free_debugcheck at mm/slab.c:2748!
Alright, this one is only triggered when slab debugging is enabled. The
slabs are assumed to be aligned on a HUGEPTE_TABLE_SIZE boundary. The free
path makes use of this assumption and uses the lowest nibble to pass around
an index into an array of kmem_cache pointers. With slab debugging turned
on, the slab is still aligned, but the "working" object pointer is not.
This would break the assumption above that a full nibble is available for
the PGF_CACHENUM_MASK.
The following patch reduces PGF_CACHENUM_MASK to cover only the two least
significant bits, which is enough to cover the current number of 4 pgtable
cache types. Then use this constant to mask out the appropriate part of
the huge pte pointer.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compile fails without defining CONFIG_PCI.
The patch fix this.
[paulus@samba.org: Moved of_irq_pci_swizzle so we only need one #ifdef]
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we get an illegal instruction exception, we check to see whether
the instruction is one that we emulate for the user program. Some of
the masks we use in checking whether the offending instruction is one
we care about didn't have the top bit set, which is the MSB of the
major opcode. Thus some undefined opcodes could get emulated as other
(defined but unimplemented) instructions. This corrects the masks.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch passes the UPIO_TSI flag to general 8259 serial driver
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch rewrites mpc7448hpc2 board irq support according to the new
mpic device tree interface.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootx_init.c trampoline didn't properly add the ramdisk to the
"reserve map" (list of reserved areas of memory), thus causing all sorts
of failures when using BootX with an initrd. Also fixes a possible
problem if the ramdisk is located before the device-tree passed by
BootX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are two problems in the powerpc gettimeofday code which can
cause incorrect results to be returned.
The first is that there is a race between do_gettimeofday and the
timer interrupt:
1. do_gettimeofday does get_tb()
2. decrementer exception on boot cpu which runs timer_recalc_offset,
which also samples the timebase and updates the do_gtod structure
with a greater timebase value.
3. do_gettimeofday calls __do_gettimeofday, which leads to the
negative result from tb_val - temp_varp->tb_orig_stamp.
The second is caused by taking the boot cpu offline, which can cause
the value of tb_last_jiffy to be increased past the currently
available timebase, causing the same underflow as above.
[paulus@samba.org - define and use data_barrier() instead of mb().]
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code. Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 919fede6ed commit)
* Fix IRQ support in the 85xx CDS boards so it uses the new
generic stuff
* Fix PCI IRQ mapping to use the device tree
* Disabled i8259 support to allow the CDS to boot. This will be
fixed soon, but the current code doesn't even compile, so this
is a vast improvement
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Fixed 8540 ADS support for the new irq layer
* Fixed 8540 ADS support for mapping PCI interrupts
* Updated 8540 ADS to use device tree for interrupt assignment
and sense values
Signed-off-by: Paul Mackerras <paulus@samba.org>
This contains board-specific portion to respect driver changes (for 8272ads ,
885ads and 866ads). Altered platform_data structures as well as initial setup
routines relevant to fs_enet.
Changes to the mpc8560ads ppc/ code are also introduced, but mainly as
reference, since the entire board support is going to appear in arch/powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI 3.0 appended a variable length UID string to the LAPIC structure
as part of support for > 256 processors. So the BAD_MADT_ENTRY() sanity
check can no longer compare for equality with a fixed structure length.
Signed-off-by: Alexey Y Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Patch from Nicolas Pitre
The userspace helpers in clean/arch/arm/kernel/entry-armv.S are called
directly in/from userspace. They need to cope with being called from
Thumb code.
Patch below uses the bx interworking instruction when
CONFIG_ARM_THUMB=y.
Based on an earlier patch from Paul Brook <paul@codesourcery.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
This is instead of a magic number.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Kevin Hilman
Previous locking changes to dmabounce incorrectly return non-NULL even
when buffer not found. Fix it up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
tidy up the makefile by using TABs to indent, and ensure
that all items are indented the same.
Move the DMA to its own section, ready for the next set
of updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
A number of small issues with the S3C24XX DMA have
cropped up, which this patch fixes. These are:
- check wether we can load another buff in start
- update state handling in s3c2410_dma_lastxfer
- only reload in irq if channel is not idle
- more informative timeout errors (add source)
- do not call request_irq() with irqs locked
- added waitforstop function
The patch also adds a S3C2410_DMAOP_STARTED for
the occasions when the driver wants to ensure that
the DMA system load state is resynced after loading.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per list discussion, let's add device tree source files
under powerpc/boot/dts. If nothing else, it is a starting point.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also accept "local-mac-address". However the old "address"
is now obsolete, but accepted for backwards compatibility.
It should be removed after all device trees have been
converted to use "mac-address".
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clear HID0[en_attn] at CPU init time on PPC970. Closes CVE-2006-4093.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code for using the radix tree for reverse mapping of interrupts has
a typo that causes it to create incorrect mappings if the software and
hardware numbers happen to be different. This would, among others, cause
the IDE interrupt to fail on js20's. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- On archs that have no-exec support, we vmalloc() a executable scratch
area of PAGE_SIZE and divide it up into an array of slots of maximum
instruction size for that arch
- On a kprobe registration, the original instruction is copied to the
first available free slot, so if multiple kprobes are registered, chances
are, they get contiguous slots
- On POWER4, due to not having coherent icaches, we could hit a situation
where a probe that is registered on one processor, is hit immediately on
another. This second processor could have fetched the stream of text from
the out-of-line single-stepping area *before* the probe registration
completed, possibly due to an earlier (and a different) kprobe hit and
hence would see stale data at the slot.
Executing such an arbitrary instruction lead to a problem as reported
in LTC bugzilla 23555.
The correct solution is to call flush_icache_range() as soon as the
instruction is copied for out-of-line single-stepping, so the correct
instruction is seen on all processors.
Thanks to Will Schmidt who tracked this down.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To compile kexec on 32-bit we need a few more bits and pieces. Rather
than add empty definitions, we can make crash.c work on 32-bit, with
only a couple of kludges.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We're missing a few functions for kexec to compile on 32-bit. There's
nothing really 64-bit specific about the 64-bit versions, so make them
generic rather than adding empty definitions for 32-bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updating the defconfigs for iseries, pseries, and G5. Sticking with
the defaults, with the following exceptions: I've turned off HW_RANDOM
for all three configs. For G5, I've enabled SND_AOA and friends as
modules; this includes the FABRIC_LAYOUT, ONYX, TAS, TOONIE and
SOUNDBUS* config options.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the case of a system hang, the user will invoke soft-reset to
initiate the kdump boot. If xmon is enabled, the CPU(s) enter into the
xmon debugger. Unfortunately, the secondary CPU(s) will return to the
hung state when they exit from the debugger (returned from die() ->
system_reset_exception()). This causes a problem in kdump since the
hung CPU(s) will not respond to the IPI sent from kdump. This patch
fixes the issue by calling crash_kexec_secondary() directly from
system_reset_exception() without returning to the previous state. These
secondary CPUs wait 5ms until the kdump boot is started by the primary
CPU. In the case we exited from the debugger to "recover" (command 'x'
in xmon) the primary and the secondary CPUs will all return from die()
-> system_reset_exception() ->crash_kexec_secondary() wait 5ms, then
return to the previous state. A kdump boot is not started in this case.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A BIOS has been found that resumes from S3 to the routine that invoked suspend,
ignoring the resume vector. This appears to the OS as a failed S3 attempt.
This same system suspend/resume's properly with Windows.
It is possible to invoke the protected mode register restore routine (which
would normally restore the sysenter registers) when the BIOS returns from
S3. This has no effect on a correctly running system and repairs the
damage from the deviant BIOS.
Signed-off-by: William Morrow <william.morrow@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously the message was "Fatal exception: panic_on_oops", as introduced
in a recent patch whith removed a somewhat dangerous call to ssleep() in
the panic_on_oops path. However, Paul Mackerras suggested that this was
somewhat confusing, leadind people to believe that it was panic_on_oops
that was the root cause of the fatal exception. On his suggestion, this
patch changes the message to simply "Fatal exception". A suitable oops
message should already have been displayed.
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some laptops with VIA C3 processor, CLE266 chipset and
AMI BIOS have incorrect latency values in FADT table. These
laptops seems to be C3 capable, but latency values are to
big: 101 for C2 and 1017 for C3. This option will allow
user to skip C3 latency test but not C3 address test. AMI
BIOS is setting C3 address to correct value in DSDT table.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Yoav Steinberg
Flash resource mapping for versatile machine included one extra byte for the end address. This results in failure to map other resources on physical address directly after the NOR flash.
Signed-off-by: Yoav Steinberg <yoav@monfort.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ACPI C3 works for "Powersaver" processors, so use it only for them.
Older CPU will change frequency on "halt" only. But we can protect transition
in two ways:
- by ACPI PM2 register, there is "bus master arbiter disable" bit.
This isn't tested because VIA mainboards don't have PM2 register,
- by PLE133 PCI/AGP arbiter disable register.
There are two bits in this register. First is "PCI arbiter disable",
second "AGP arbiter disable". This is working on VIA Epia 800 mainboards.
Test on bm_control is more proper because this is true
when PM2 register exist.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Jack Steiner identified a problem where XPC can cause a silent
data corruption. On module load, the placement may cause the
xpc_remote_copy_buffer to span two physical pages. DMA transfers are
done to the start virtual address translated to physical.
This patch changes the buffer from a statically allocated buffer to a
kmalloc'd buffer. Dean Nelson reviewed this before posting. I have
tested it in the configuration that was showing the memory corruption
and verified it works. I also added a BUG_ON statement to help catch
this if a similar situation is encountered.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This adds a shadow buffer for the SLBs and regsiters it with PHYP.
Only the bolted SLB entries (top 3) are shadowed.
The SLB shadow buffer tells the hypervisor what the kernel needs to
have in the SLB for the kernel to be able to function. The hypervisor
can use this information to speed up partition context switches.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PIN_SIZE definition name changed, update 44x_mmu.c accordingly.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removes the flush_dcache_all export for non coherent platforms.
We removed the last in-kernel user of this years ago in arch/ppc
so it no longer serves a purpose. Plus, it breaks the build
at the moment.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As per list discussion, let's add device tree source files
under powerpc/boot/dts. If nothing else, it is a starting point.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't have much in the way of doc comments, but some of those we do have
don't work because they start with "/***" or "/*", not "/**" which is what
kernel-doc requires.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I think that most people who use maple_defconfig are doing so for a JS21,
so it might make sense to turn Tigon3 support on by default.
Built and booted on a JS21.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code. Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Noticing the following might_sleep warning (dump_stack()) during kdump
testing when CONFIG_DEBUG_SPINLOCK_SLEEP is enabled. All secondary CPUs
will be calling rtas_set_indicator with interrupts disabled to remove
them from global interrupt queue.
BUG: sleeping function called from invalid context at
arch/powerpc/kernel/rtas.c:463
in_atomic():1, irqs_disabled():1
Call Trace:
[C00000000FFFB970] [C000000000010234] .show_stack+0x68/0x1b0 (unreliable)
[C00000000FFFBA10] [C000000000059354] .__might_sleep+0xd8/0xf4
[C00000000FFFBA90] [C00000000001D1BC] .rtas_busy_delay+0x20/0x5c
[C00000000FFFBB20] [C00000000001D8A8] .rtas_set_indicator+0x6c/0xcc
[C00000000FFFBBC0] [C000000000048BF4] .xics_teardown_cpu+0x118/0x134
[C00000000FFFBC40] [C00000000004539C]
.pseries_kexec_cpu_down_xics+0x74/0x8c
[C00000000FFFBCC0] [C00000000002DF08] .crash_ipi_callback+0x15c/0x188
[C00000000FFFBD50] [C0000000000296EC] .smp_message_recv+0x84/0xdc
[C00000000FFFBDC0] [C000000000048E08] .xics_ipi_dispatch+0xf0/0x130
[C00000000FFFBE50] [C00000000009EF10] .handle_IRQ_event+0x7c/0xf8
[C00000000FFFBF00] [C0000000000A0A14] .handle_percpu_irq+0x90/0x10c
[C00000000FFFBF90] [C00000000002659C] .call_handle_irq+0x1c/0x2c
[C00000000058B9C0] [C00000000000CA10] .do_IRQ+0xf4/0x1a4
[C00000000058BA50] [C0000000000044EC] hardware_interrupt_entry+0xc/0x10
--- Exception: 501 at .plpar_hcall_norets+0x14/0x1c
LR = .pseries_dedicated_idle_sleep+0x190/0x1d4
[C00000000058BD40] [C00000000058BDE0] 0xc00000000058bde0 (unreliable)
[C00000000058BDF0] [C00000000001270C] .cpu_idle+0x10c/0x1e0
[C00000000058BE70] [C000000000009274] .rest_init+0x44/0x5c
To fix this issue, rtas_set_indicator_fast() is added so that will not
wait for RTAS 'busy' delay and this new function is used for kdump (in
xics_teardown_cpu()) and for CPU hotplug ( xics_migrate_irqs_away() and
xics_setup_cpu()).
Note that the platform architecture spec says that set-indicator
on the indicator we're using here is not permitted to return the
busy or extended busy status codes.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We should not be calling power4_enable_pmcs() in
pseries_lpar_enable_pmcs(); just doing the hypercall is sufficient.
Prior to 2.6.15 we did not call power4_enable_pmcs() for an lpar.
power4_enable_pmcs() tries to read the hid0 register which is no
longer legal for an lpar in newer Power processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use __cpuinit for CPU hotplug notifier function.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Conflicts:
arch/ia64/hp/sim/simscsi.c
Stylistic differences in two separate fixes for buffer->request_buffer
problem.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean up proc file removal in sq module for superh arch. currently on a
failed module load or on module unload a proc file is left registered which
can cause a random memory execution or oopses if read after unload. This
patch cleans up that deregistration.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Martin Michlmayr
Fix the following compilation error in arm/mach-ixp4xx/gtwx5715-setup:
CC arch/arm/mach-ixp4xx/gtwx5715-setup.o
arch/arm/mach-ixp4xx/gtwx5715-setup.c:110: error: expected identifier or '(' before = token
arch/arm/mach-ixp4xx/gtwx5715-setup.c:121: error: 'gtwx5715_flash_resource' undeclared here (not in a function)
arch/arm/mach-ixp4xx/gtwx5715-setup.c: In function 'gtwx5715_init':
arch/arm/mach-ixp4xx/gtwx5715-setup.c:133: error: 'flash_resource' undeclared (first use in this function)
arch/arm/mach-ixp4xx/gtwx5715-setup.c:133: error: (Each undeclared identifier is reported only once
arch/arm/mach-ixp4xx/gtwx5715-setup.c:133: error: for each function it appears in.)
make[1]: *** [arch/arm/mach-ixp4xx/gtwx5715-setup.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
Fix "WARNING: "rtc_next_alarm_time" [drivers/rtc/rtc-sa1100.ko]
undefined!"
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The uncached allocator has a function, uncached_get_new_chunk(), that needs
to be serialized on a per node basis. It also has a global variable,
allocated_granules, which should be defined on a per node basis and protected
by that serialization. Additionally, all error returns from functions called
(like ia64_pal_mc_drain()) should be handled appropriately.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Acked-by: Jes Sorenson <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Propagate acpi_processor_preregister_performance return value.
[CPUFREQ] [2/2] demand load governor modules.
[CPUFREQ] [1/2] add __find_governor helper and clean up some error handling.
[CPUFREQ] Longhaul - Rename & fix multipliers table
[CPUFREQ] Longhaul - Fix power state test to do something more useful
[CPUFREQ] Longhaul - Readd accidentally dropped line
[CPUFREQ] Make longhaul_walk_callback() static
[CPUFREQ] X86_GX_SUSPMOD must depend on PCI
[CPUFREQ] Longhaul - Initialise later.
[CPUFREQ] Longhaul - Workaround issues with APIC.
[CPUFREQ] Longhaul - Hook into ACPI C states.
[CPUFREQ] return error when failing to set minfreq
contig.c (FLATMEM) requires the same optimization as in discontig.c for show_mem
when VIRTUAL_MEM_MAP is in use. Otherwise FLATMEM has softlockup timeouts.
This was boot tested for memory configuration: SPARSEMEM,
DISCONTIG+VIRTUAL_MEM_MAP, FLATMEM, FLATMEM+VIRTUAL_MEM_MAP and
FLATMEM+VIRTUAL_MEM_MAP with largest memory gap less than LARGE_GAP by
using boot parameter "mem=".
This was boot tested and "echo m >/proc/sysrq-trigger" output evaluated for
: FLATMEM, FLATMEM+VIRTUAL_MEM_MAP, DISCONTIGMEM+VIRTUAL_MEM_MAP and
SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Assure that vmem_map's high endpoint is MAX_ORDER aligned. Not doing so violates
the buddy allocator algorithm. Also anyone using mem=XXX on boot line and
not aligned to MAX_ORDER requires this patch in order to satisfy buddy
allocator. vmem_map always starts at pfn 0. The potentially large MAX_ORDER
on ia64 (due to hugetlbfs) requires that the end of vmem_map be aligned
to MAX_ORDER_NR_PAGES.
This was boot tested for: FLATMEM, FLATMEM+VIRTUAL_MEM_MAP,
DISCONTIGMEM+VIRTUAL_MEM_MAP and SPARSEMEM.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
CONFIG_MD_RAID5 became CONFIG_MD_RAID456 in drivers/md/Kconfig. Make
the same change in arch/ia64
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Aron Griffis <aron@hp.com>
Acked-by: Jes Sorenson <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
If CONFIG_IOMMU_DEBUG is set force_iommu defaults to 1. In the case
where no HW IOMMU is present in the machine and we end up using nommu,
leaving force_iommu set to 1 causes dma_alloc_coherent to do the wrong
thing. Therefore, if we end up using nommu, make sure force_iommu is
0.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Re-add backlink for old style unwinder to stack switching. Add proper
stack frame and CFI annotations to call_softirq
This prevents a oops when backtracing with fallback through the
interrupt stack top.
Suggested by Jan Beulich and Herbert Xu wanted it in 2.6.18.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I think ia64_switch_mode_phys and ia64_switch_mode_virt
does not need to alloc an empty frame.
An empty frame is required by loadrs but flushrs
does not need that.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We found an issue in pal.S.
According to the software runtime SPEC,
The caller's output registers do not need to be preserved for
caller. The callee may reuse input registers for any other
purpose within the procedure.
in ia64_pal_call_phys_stacked,
input registers are copied to output registers before call
into ia64_switch_mode_phys, then used to call into PAL. This
assumes output registers are preserved in ia64_switch_mode_phys,
which may not be true.
In this particular case, ia64_switch_mode_phys alloc a null frame
, and mask off psr.i.
If an interrupt comes at this small window,
or an MCA comes inside the procedure, output registers
maybe changed,
then the pal call may got some staled input registers.
This patch moves the copies from input to output
after ia64_switch_mode_phys to follow the software
runtime convention.
It also removed some unused labels in
ia64_pal_call_phys_stacked.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix some sparse warnings on ia64. Large constants that should be long
instead of int. Use NULL instead of 0. Add some missing __iomem
casts. Replace a non-C99 structure assignment.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from David Brownell
ARM genirq cleanups/updates:
- Start switching platforms to newer APIs
* use "irq_chip" name, not "irqchip"
* providing irq_chip.name
- Show irq_chip.name in /proc/interrupts, like on x86.
This update a bit more than half of the ARM code. The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our pseries hcall interfaces are out of control:
plpar_hcall_norets
plpar_hcall
plpar_hcall_8arg_2ret
plpar_hcall_4out
plpar_hcall_7arg_7ret
plpar_hcall_9arg_9ret
Create 3 interfaces to cover all cases:
plpar_hcall_norets: 7 arguments no returns
plpar_hcall: 6 arguments 4 returns
plpar_hcall9: 9 arguments 9 returns
There are only 2 cases in the kernel that need plpar_hcall9, hopefully
we can keep it that way.
Pass in a buffer to stash return parameters so we avoid the &dummy1,
&dummy2 madness.
Signed-off-by: Anton Blanchard <anton@samba.org>
--
Signed-off-by: Paul Mackerras <paulus@samba.org>
Note how any error from acpi_processor_preregister_performance is ignored.
From: bert hubert <bert.hubert@netherlabs.nl>
Signed-off-by: Dave Jones <davej@redhat.com>
This table is only used by Ezra-T CPUs currently, and has values
for some other CPU. Fix them to match the values used by that CPU,
and for now make it clearer by renaming the variable.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This is changing "always true" test to something usefull.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch makes the needlessly global longhaul_walk_callback() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
It seems commit 32ee8c3e47 accidentially
reverted cdc9cc1d74, IOW, it reintroduced
the following compile error with CONFIG_PCI=n:
<-- snip -->
...
CC arch/i386/kernel/cpu/cpufreq/gx-suspmod.o
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c: In function ‘gx_detect_chipset’:
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: error: implicit declaration of function ‘pci_match_id’
arch/i386/kernel/cpu/cpufreq/gx-suspmod.c:193: warning: comparison between pointer and integer
make[3]: *** [arch/i386/kernel/cpu/cpufreq/gx-suspmod.o] Error 1
<-- snip -->
This patch therefore re-adds the dependency of X86_GX_SUSPMOD on PCI.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Without this longhaul will always fail when compiled into kernel,
as it needs to initialise after the ACPI processor module.
I lost this when I was splitting patches. Sorry.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
There is no need to worry about local APIC.
There is need to worry about I/O APIC, because I/O APIC
is replacing good old 8259. According to Nehemiah datasheet VIA is
using 3-wire bus to connect local APIC to I/O APIC.
"[...] When IA32_APIC_BASE[11] is set to 0, processor APICs based on the 3-wire APIC
bus cannot be generally re-enabled until a system hardware reset. The 3-wire bus
looses track of arbitration that would be necessary for complete re-enabling. Certain
(local) APIC functionality can be enabled. [...]"
So we must set disable bit for each interrupt in I/O APIC registers.
Same situation as for PIC - we must poke registers direcly.
How to do this? I don't know. So at the moment it is better to fail.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Minimal change necessary for hardware support.
Changes in longhaul.c:
- most important - now C3 state is causing transition,
- code responsible for clearing "bus master" bit removed,
- protect bcr2 transition in the same way as longhaul.
Signed-off-by: Rafa Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Minor comment fix for misc_64.S
[POWERPC] Use H_CEDE on non-SMT
[POWERPC] force 64bit mode in fwnmi handlers to workaround firmware bugs
[POWERPC] PMAC_APM_EMU should depend on ADB_PMU
[POWERPC] Fix new interrupt code (MPIC detection)
[POWERPC] Fix new interrupt code (MPIC endianness)
[POWERPC] Add cpufreq support for Xserve G5
[POWERPC] Xserve G5 thermal control fixes
[POWERPC] Fix mem= handling when the memory limit is > RMO size
[POWERPC] More offb/bootx fixes
[POWERPC] Fix legacy_serial.c error handling on 32 bits
[POWERPC] Fix default clock for udbg_16550
[POWERPC] Fix non-MPIC CHRPs with CONFIG_SMP set
[POWERPC] Fix 32 bits warning in prom_init.c
[POWERPC] Workaround Pegasos incorrect ISA "ranges"
[POWERPC] fix up front-LED Kconfig
This patch fixes several problems:
- The legacy backlight value might be set at interrupt time. Introduced
a worker to prevent it from directly calling the backlight code.
- via-pmu allows the backlight to be grabbed, in which case we need to
prevent other kernel code from changing the brightness.
- Don't send PMU requests in via-pmu-backlight when the machine is about
to sleep or waking up.
- More Kconfig fixes.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CFA needs to be adjusted upwards for push, and downwards for pop.
arch/i386/kernel/entry.S gets it wrong in one place.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The latest toolchains can produce a new ELF section in DSOs and
dynamically-linked executables. The new section ".gnu.hash" replaces
".hash", and allows for more efficient runtime symbol lookups by the
dynamic linker. The new ld option --hash-style={sysv|gnu|both} controls
whether to produce the old ".hash", the new ".gnu.hash", or both. In some
new systems such as Fedora Core 6, gcc by default passes --hash-style=gnu
to the linker, so that a standard invocation of "gcc -shared" results in
producing a DSO with only ".gnu.hash". The new ".gnu.hash" sections need
to be dealt with the same way as ".hash" sections in all respects; only the
dynamic linker cares about their contents. To work with older dynamic
linkers (i.e. preexisting releases of glibc), a binary must have the old
".hash" section. The --hash-style=both option produces binaries that a new
dynamic linker can use more efficiently, but an old dynamic linker can
still handle.
The new section runs afoul of the custom linker scripts used to build vDSO
images for the kernel. On ia64, the failure mode for this is a boot-time
panic because the vDSO's PT_IA_64_UNWIND segment winds up ill-formed.
This patch addresses the problem in two ways.
First, it mentions ".gnu.hash" in all the linker scripts alongside ".hash".
This produces correct vDSO images with --hash-style=sysv (or old tools),
with --hash-style=gnu, or with --hash-style=both.
Second, it passes the --hash-style=sysv option when building the vDSO
images, so that ".gnu.hash" is not actually produced. This is the most
conservative choice for compatibility with any old userland. There is some
concern that some ancient glibc builds (though not any known old production
system) might choke on --hash-style=both binaries. The optimizations
provided by the new style of hash section do not really matter for a DSO
with a tiny number of symbols, as the vDSO has. If someone wants to use
=gnu or =both for their vDSO builds and worry less about that
compatibility, just change the option and the linker script changes will
make any choice work fine.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The SGI IOC4 IDE device always shares an interrupt with other devices which
are part of IOC4. As such, IDEPCI_SHARE_IRQ should always be enabled when
BLK_DEV_SGIIOC4 is enabled.
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use hotplug version of register_cpu_notifier in late init functions.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few of the callback functions and notifier blocks that are associated with cpu
notifications incorrectly have __devinit and __devinitdata. They should be
__cpuinit and __cpuinitdata instead.
It makes no functional difference but wastes text area when CONFIG_HOTPLUG is
enabled and CONFIG_HOTPLUG_CPU is not.
This patch fixes all those instances.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is part of an effort to unify the panic_on_oops behaviour across
all architectures that implement it.
It was pointed out to me by Andi Kleen that if an oops has occured in
interrupt context, then calling sleep() in the oops path will only cause a
panic, and that it would be really better for it not to be in the path at
all.
This patch removes the ssleep() call and reworks the console message
accordinly. I have a slght concern that the resulting console message is
too long, feedback welcome.
For powerpc it also unifies the 32bit and 64bit behaviour.
Fror x86_64, this patch only updates the console message, as ssleep() is
already not present.
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When resuming from suspend-to-RAM, the NMI watchdog detects a lockup in
ide_wait_not_busy. Here's a screenshot of the trace taken by a digital
camera: http://www.uamt.feec.vutbr.cz/rizeni/pom/DSC03510-2.JPG
Let's touch the NMI watchdog in ide_wait_not_busy. The system then resumes
correctly from STR.
[akpm@osdl.org: modular build fix]
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kprobe inserts breakpoint instruction in probepoint and then jumps to
instruction slot when breakpoint is hit, the instruction slot icache must
be consistent with dcache. Here is the patch which invalidates instruction
slot icache area.
Without this patch, in some machines there will be fault when executing
instruction slot where icache content is inconsistent with dcache.
Signed-off-by: bibo,mao <bibo.mao@intel.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Keshavamurthy Anil S <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove a
duplicate of the macro. Also remove some trailing whitespaces and needless
braces.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is described as being experimental, but doesn't actually depend on
EXPERIMENTAL. Change the text.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kprobe-booster's safety check against preemption does not work well
now, because the preemption count has been modified by read_rcu_lock() in
atomic_notifier_call_chain() before we check it. So, I'd like to prevent
boosting kprobe temporarily if the kernel is preemptable.
Now we are searching for the good solution.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of my original comments in machine_kexec was unclear
and this should fix it.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Horms <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Move the tsc synchronisation variables into a struct, mark it __initdata
- local `realdelta' wants to be 64-bit
- Print the skew for negative skews, as well as for positive ones
- remove dead code
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mce_disabled cannot be __initdata - we access it during APM resume.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/ia64/hp/sim/simscsi.c: In function `simscsi_sg_readwrite':
arch/ia64/hp/sim/simscsi.c:154: error: structure has no member named `buffer'
arch/ia64/hp/sim/simscsi.c: In function `simscsi_fillresult':
arch/ia64/hp/sim/simscsi.c:247: error: structure has no member named `buffer'
hch said:
>Just change it to access the request_buffer member instead. buffer
>and request_buffer have been synonymous 99% of the time, and a driver
>never even wants to access buffer.
Signed-off-by: Tony Luck <tony.luck@intel.com>
